Solubility and binding properties of PEGylated lysozyme derivatives with increasing molecular weight on hydrophobic-interaction chromatographic resins

Dynamic binding capacities and resolution of PEGylated lysozyme derivatives with varying molecular weights of poly (ethylene) glycol (PEG) with 5 kDa, 10 kDa and 30 kDa for HIC resins and columns are presented. To find the optimal range for the operating conditions, solubility studies were performed by high-throughput analyses in a 96-well plate format, and optimal salt concentrations and pH values were determined. The solubility of PEG-proteins was strongly influenced by the length of the PEG moiety. Large differences in the solubilities of PEGylated lysozymes in two different salts, ammonium sulfate and sodium chloride were found. Solubility of PEGylated lysozyme derivatives in ammonium sulfate decreases with increased length of attached PEG chains. In sodium chloride all PEGylated lysozyme derivatives are fully soluble in a concentration range between 0.1 mg protein/ml and 10 mg protein/ml. The binding capacities for PEGylated lysozyme to HIC resins are dependent on the salt type and molecular weight of the PEG polymer. In both salt solutions, ammonium sulfate and sodium chloride, the highest binding capacity of the resin was found for 5 kDa PEGylated lysozyme. For both native lysozyme and 30 kDa mono-PEGylated lysozyme the binding capacities were lower. In separation experiments on a TSKgel Butyl-NPR hydrophobic-interaction column with ammonium sulfate as mobile phase, the elution order was: native lysozyme, 5 kDa mono-PEGylated lysozyme and oligo-PEGylated lysozyme. This elution order was found to be reversed when sodium chloride was used. Furthermore, the resolution of the three mono-PEGylated forms was not possible with this column and ammonium sulfate as mobile phase. In 4 M sodium chloride a resolution of all PEGylated lysozyme forms was achieved. A tentative explanation for these phenomena can be the increased solvation of the PEG polymers in sodium chloride which changes the usual attractive hydrophobic forces in ammonium sulfate to more repulsive hydration forces in this hydrotrophic salt.     

Radiation induced synthesis and swelling characterization of thermo-responsive N-isopropylacrylamide-co-ionic hydrogels

Two-component thermo-responsive hydrogels poly(N-isopropylacrylamide)-co-vinylbenzyltrimethylammonium chloride (NIPA-co-VBT) and poly(N-isopropylacrylamide)-co-p-sodium styrene sulphonate (NIPA-co-SSS) were prepared by using high energy gamma radiation. The gels were characterized by Fourier transformed infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and sol-gel analysis. The presence of ionic monomers in NIPA leads to lower gel content. Introduction of ionic components in the matrix enhanced swelling extent but caused slower volume transition. The swelling studies in alcohol indicated that swelling extent was function of polarity of the swelling medium and all gels followed the order water > methanol > ethanol > iso-propanol. In mixed co-solvents (water-alcohol), they exhibit complex reentrant behavior. The co-polymer gels containing VBT swelled faster and to higher extent than those containing SSS. The dynamic swelling studies indicated that diffusion of water in PNIPA gel shifts from Fickian for PNIPA to anomalous for NIPA-co-ionic gels also the mean swelling time (MST) decreases for gels containing ionic monomers.     

ATRP synthesis and association properties of temperature responsive dextran copolymers grafted with poly(N-isopropylacrylamide)

Temperature responsive copolymers of dextran grafted with poly(N-isopropylacrylamide) (Dex-g-PNIPAAM) were prepared by atom transfer radical polymerization (ATRP) in homogeneous mild conditions without using protecting group chemistry. Dextran macroinitiator was synthesized by reaction of dextran with 2-chloropropionyl chloride at room temperature in DMF containing 2% LiCl. ATRP was carried out in DMF:water 50:50 (v/v) mixtures at room temperature with CuBr/Tris(2-dimethylaminoethyl)amine (Me₆TREN) as catalyst. Several grafted copolymers with well defined number and length of low polydispersity grafted chains were prepared. Temperature induced association properties in aqueous solution were studied as a function of temperature and polymer concentration by dynamic light scattering, fluorescence spectroscopy and atomic force microscopy (AFM). LCST, ranging from 35 to 41 °C, was significantly affected by number and length of grafted chains. The fine tuning of LCST around body temperature is an important characteristic not obtainable by conventional radical grafting of PNIPAAM. Well defined spherical nanoparticles were formed above the LCST of PNIPAAM. Hydrodynamic diameter was in the range 73-98 nm.     

Graft polymerization from pore wall of three-dimensionally ordered macroporous cross-linked polystyrene via atom transfer radical polymerization

The surface-initiated atom-transfer radical polymerization (ATRP) technique was applied to the graft polymerization of methyl methacrylate (MMA) and N-isopropylacrylamide (NIPAm) from three-dimensionally ordered macroporous cross-linked polystyrene (3DOM CLPS) on which the initiator, halogen atom was immobilized onto the pore wall of 3DOM CLPS by chloromethylation. FT-IR and TG-DWA analyses confirm that the graft polymerization of MMA and NIPAm via ATRP had been taken place at the pore wall of 3DOM CLPS. The initiating efficiency of chloromethyl groups was calculated according to the data of TGA-titration, revealed that the benzyl chloride is not only distributed on the surface of the pore walls but also must be present throughout the inner of the cross-linked polystyrene matrix. SEM analyses show that the grafted layers are smooth and homogeneous, and the ordered structure is well preserved after polymerization. By the adjustment of the graft polymerization time, the thickness of grafted polymer layers can be controlled. The max thickness of grafted PMMA layer is 85 nm and the max thickness of grafted PNIPAm layer is 35 nm.     

Synthesis of cationic guar gum-graft-polyacrylamide at low temperature and its flocculating properties

Acrylamide grafted cationic guar gum (CGG-g-PAM), induced by ceric ammonium sulfate, was synthesized using aqueous polymerization technique at 10 °C and the flocculation property was studied with high-turbidity tobacco wastewater (NTU > 4500). Thus five grades of graft copolymers were obtained through alteration of initiator and monomer concentrations in order to understand the effect of molecular weight on flocculation. The grafted copolymer was characterized by FTIR and SEM. Study of DTG demonstrated that CGG-g-PAM had better heat-resistant performance than guar gum, cationic guar gum (CGG) and polyacrylamide. The dosage of polyaluminium chloride (PAC) and CGG-g-PAM, pH value and molecular weight were considered to be the factors that can influence flocculation efficiency. The result showed best flocculation efficiency occurs at pH 5 when the dosage of CGG-g-PAM and PAC are 3.6 ppm and 120 ppm, respectively. The percentage of turbidity and COD removal are 98% and 24% correspondingly, and its flocculating efficiency prevails over that of CGG and cationic polyacrylamide (CPAM).     

Method optimization for quantitative analysis of octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) by liquid chromatography-electrospray ionization mass spectrometry

A simple, sensitive LC-ESI-MS method was optimized for quantitative analysis of octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) in environmental samples. Under negative ionization mode, HMX can form adduct ions with various organic acids and salts, including acetic acid, formic acid, propionic acid, ammonium nitrate, ammonium chloride, sodium nitrite, and sodium nitrate. Acetic acid was chosen as additive and the ion, [M + CH₃COO]⁻ with m/z = 355 was used for selective ion monitoring (SIM) in this study. Good sensitivity was achieved with low acetic acid concentration in the mobile phase and relatively low capillary temperature. The method detection limit was 0.78 pg for HMX in standard solution. Linearity (R² > 0.9998) was obtained at low concentrations (0.5-50 μg/L). This method has been used to determine HMX concentrations in water samples and lizard egg samples from an animal exposure study.     

Radical polymerization behavior of 3-(N-2-methacryloyloxyethyl-N,N-dimethyl)ammonatopropanesulfonate in water

The homogeneous polymerization of 3-(N-2-methacryloyloxyethyl-N,N-dimethyl)ammonatopropanesulfonate (MDAPS) with potassium peroxydisulfate (KPS) was kinetically in situ investigated in water by means of FT-near IR spectroscopy. The overall activation energy of the polymerization was calculated to be 16.0 kcal/mol. The initial polymerization rate (R_p) at 40 °C was expressed by R_p=k[KPS]^0.65[MDAPS]^1.0. The presence of alkaline metal salts was observed to accelerate the polymerization. The order of acceleration at 40 °C was CsCl > KCl > NaCl > LiCl when the chloride salts were used. NaCl showed higher acceleration effect than NaF. NaBr and NaI exhibited retardation and inhibition effect, respectively, because of reduction of KPS and its primary radical with bromide and iodide ions. The polymerization of MDAPS with KPS in water in the presence of NaCl at 2.0 mol/l gave R_p=k[KPS]^0.70[MDAPS]^1.4 at 40 °C. The overall activation energy of the polymerization in the presence of NaCl was estimated to be 11.6 kcal/mol being considerably lower value compared with that in its absence. The syndiotacticity of poly(MDAPS) tended to increase with rising temperature and decrease in the presence of NaCl.     

Dispersion copolymerization of acrylamide with quaternary ammonium cationic monomer in aqueous salts solution

Dispersion copolymerization of acrylamide (AM) with 2-methylacryloylxyethyl trimethyl ammonium chloride (DMC) has been carried out in aqueous salts solution containing ammonium sulfate and sodium chloride with poly(acryloylxyethyl trimethyl ammonium chloride) (PDAC) as the stabilizer and 2,2′-azobis[2-(2-inidazolin-2-yl)propane]-dihydro chloride (VA-044) as the initiator. A new particle formation mechanism of the dispersion polymerization for the present system has been proposed. The effects of inorganic salts and stabilizer concentration on dispersion polymerization have been investigated. The results show that varying the salt concentration could affect the morphology and molecular weight of the resultant copolymer particles significantly. With increasing the stabilizer concentration, the particle size decreased at first and then increased, meanwhile the effect on the copolymer molecular weight was the contrary. These results had been rationalized based on the proposed mechanism.     

Surface modification of lyocell fibres by graft copolymerization of thermo-sensitive poly-N-isopropylacrylamide

Thermo-sensitive poly-N-isopropylacrylamide (poly-NIPAAm) was grafted onto lyocell fibres using cerium ammonium nitrate (CAN) as initiator. The effects of initiation time, initiator concentration, monomer concentration and grafting time on the degree of grafting were investigated. A 15-60 min exposure time, 7.5 mM CAN solution concentration and a 0.5-1 mM NIPAAm monomer concentration were optimal for obtaining a maximum degree of grafting (60-70% at 24 h grafting time) of poly-NIPAAm on lyocell fibres. Higher degree of grafting was obtained increasing the grafting time, such as 120% at 72 h.The properties of the obtained poly-NIPAAm/lyocell copolymer were also investigated. Specifically, the effects of temperature and degree of grafting of poly-NIPAAm on the swelling behaviour of the copolymer were experimentally determined. Moreover, structural characterization, thermal behaviour and morphology of the poly-NIPAAm/lyocell copolymers were examined by Fourier Transform Infrared Spectroscopy (FTIR), Differencial Scanning Calorimetry (DSC) and Scanning electron microscopy (SEM) techniques, respectively.     

Preparation of poly(N-isopropylacrylamide)-grafted well-controlled 3D skeletal monolith based on E-51 epoxy resin for protein separation

A novel type of poly(N-isopropylacrylamide) grafted E-51 epoxy-based monoliths in a 100 mm × 4.6 mm I.D. stainless steel column with well-controlled three-dimensional skeletal structures has been prepared and proposed for the separation of proteins. The grafted PNIPAAm chain via surface-initiated atom transfer radical polymerization was successfully performed. The proposed method provided a new route to modify the E-51 epoxy-based monoliths for widening their applications. Meanwhile, the temperature and the salt concentration responses of the grafted monolithic columns were investigated. Under the salt gradient, six proteins were well separated in hydrophobic interaction mode. Moreover, for further confirming the application of the prepared monolith was meaningful for proteome analysis in actual system, the separation of human serum sample was performed.     

Preparation, characterization and enzyme inhibition of methylmethacrylate copolymer nanoparticles with different hydrophilic polymeric chains

Methylmethacrylate copolymer nanoparticles with different hydrophilic chains were prepared by the free radical polymerization of methylmethacrylate with N-isopropylacrylamide (NIPAAm), N-methacrylic acid (MAA), N-trimethylaminoethylmethacrylate chloride (TMAEMC) or N-dimethylaminoethylmethacrylate hydrochloride (DMAEMC). These particles were characterized by particle size and zeta potential. The polymerization conditions were shown to influence the particle size and surface charge. Particle sizes of MMA-NIPAAm nanoparticles after 3 h of reaction reached constant level at 180 nm. An increasing amount of total monomer (0.5-5%) would result in the nanoparticles of particle size of 115-204 nm for 30% NIPAAm of the total monomer. In the same range of 5-40% NIPAAm of the total monomer, the particle size decreased from 280 to 170 nm. The concentration of the initiator APS up to a concentration of 0.2% for MMA-TMAEMC and 0.1% for MMA-NIPAAm showed no effect on the particle size of the final nanoparticle suspensions, while higher concentration would lead to aggregation in the polymerization process. MMA-NIPAAm nanoparticles were pH-dependent in zeta potential at pH 1-12 values reducing from 12.2 mV to −16.8 mV, respectively. Nanoparticles were incubated with pepsin and trypsin at 37 °C for 20 min and their enzyme inhibition was determined. The activity of pepsin decreased to 27% in the presence of MMA-NIPAAm nanoparticles, and MMA-MAA nanoparticles reduced the activity of trypsin to 39%, respectively.     

Preparation and characterization of dendrimer-star PNIPAAM using dithiobenzoate-terminated PPI dendrimer via RAFT polymerization

Two dendritic reversible addition-fragmentation transfer (RAFT) agents with 8 and 16 terminal dithiobenzoate (DTB) groups on the surface of poly(propylene imine) (PPI) dendrimers (generation 2.0 and 3.0, respectively) were successively prepared, and they were used in the RAFT polymerization of N-isopropylacrylamide (NIPAAM). The polymerization kinetics was confirmed to pseudo-first-order behavior. The ¹H NMR and GPC analyses show that the dendrimer-star den (NIPAAM)_x (x = 8 or 16) prepared by RAFT method has well-defined structure, controlled molecular weight and low polydispersities (PDI < 1.3). The aqueous solution prepared from dendrimer-star PNIPAAM showed reversible changes in optical properties: transparent below a lower critical solution temperature (LCST) and opaque above the LCST.     

Improved methods for the synthesis and isolation of imidazolium based ionic salts

Solvent-free reactions were used for the synthesis of a series of imidazolium-based ionic salts: 3,3′-[pyridine-2,6-diylbis(methylene)]bis(1-R-1H-imidazol-3-ium)chloride; (R = methyl, ethyl, butyl, isobutyl, hexyl, and benzyl). A simple and effective filtration process was used to isolate all the products in high purity and with yields ?93% within a 24 h period. The highly pure ionic compounds which are precursors to N-heterocyclic carbene ligands used in catalysis were fully characterized as gray-white hygroscopic salts.     

Conductivity and thermal behavior of proton conducting polymer electrolyte based on poly (N-vinyl pyrrolidone)

The polymer electrolytes based on poly N-vinyl pyrrolidone (PVP) and ammonium thiocyanate (NH₄SCN) with different compositions have been prepared by solution casting technique. The amorphous nature of the polymer electrolytes has been confirmed by XRD analysis. The shift in T_g values and the melting temperatures of the PVP-NH₄SCN electrolytes shown by DSC thermo-grams indicate an interaction between the polymer and the salt. The dependence of T_g and conductivity upon salt concentration have been discussed. The conductivity analysis shows that the 20 mol% ammonium thiocyanate doped polymer electrolyte exhibit high ionic conductivity and it has been found to be 1.7 × 10⁻⁴ S cm⁻¹, at room temperature. The conductivity values follow the Arrhenius equation and the activation energy for 20 mol% ammonium thiocyanate doped polymer electrolyte has been found to be 0.52 eV.     

Temperature-dependent molecular-recognizable membranes based on poly(N-isopropylacrylamide) and β-cyclodextrin

A novel temperature-dependent molecular-recognizable membrane, poly(N-isopropylacylamide-co-glycidyl methacrylate/cyclodextrin)-grafted-polyethylene terephthalate (P(NIPAM-co-GMA/CD)-g-PET) membrane, is prepared by the combination of plasma-induced pore-filling grafting polymerization and chemical reaction. Scanning electron microscope (SEM) images show that the surfaces and cross-sections of the prepared membranes are uniformly grafted by polymeric layer. Fourier transform infrared (FT-IR) results show that CDs are successfully induced onto the P(NIPAM-co-GMA) grafted chains through reaction with epoxy groups. When the environmental temperature increases from 25 °C to 45 °C, the contact angle of prepared P(NIPAM-co-GMA/CD)-g-PET membrane increases from 65° to 76.9°; whereas, that of substrate membrane decreases from 84.8° to 77.1°. During the dynamic adsorption experiments, the guest 8-anilino-1-naphthalenesulfonic acid ammonium salt (ANS) molecules are adsorbed onto the P(NIPAM-co-GMA/CD)-g-PET membrane at lower temperature (25 °C) and desorbed from it at higher temperature (40 °C) with good repeatability. This phenomenon of adsorption at low temperature and desorption at high temperature of the P(NIPAM-co-GMA/CD)-g-PET membrane is attributable to both the “swollen–shrunken” configuration change of P(NIPAM-co-GMA) grafted chains and the molecular recognition of CD toward ANS. The P(NIPAM-co-GMA/CD)-g-PET membrane show both good thermo-responsibility and temperature-dependent molecular-recognizable characteristics toward guest molecules, which is highly potential to be applied in temperature-controlled affinity separations.     

Drug permeation modeling through the thermo-sensitive membranes of poly(N-isopropylacrylamide) brushes grafted onto micro-porous films

Temperature-sensitive N-isopropylacrylamide (NIPAAm) polymer brushes of known molecular weight (20k–25k) were grafted onto micro-porous polycarbonate (PC) films (pore size 0.4 μm) using argon plasma treatment. The resulting composite membranes were tested for controlled drug release at various grafted chain density, which was controlled using 1–3% polymer concentrations. The composites were also characterized in terms of graft yield, membrane thickness, Fourier transform infrared (FTIR) spectra and scanning electron micrography (SEM). The drug permeabilities of 4-acetamidophenol and ranitidine HCl in the resulting membranes were determined at temperatures between 30 and 40 °C. The drug permeability changed remarkably at 34 °C, near the lower critical solution temperature (LCST). The drug passage was regulated by swelling (which occurs at a temperature lower than the LCST) or shrinkage (occurring at an elevated temperature) of the PNIPAAm polymer brushes. These membranes demonstrated on–off ratios of drug permeabilities up to 11 and 14 for the model drugs, respectively. These values are higher than most literature data with similar-size model molecules. The excellent on–off valve mechanism was discussed in terms of the suitable molecular weight and grafted chain density in relation to the pore size and porosity of the PC support. A mathematical model was proposed to predict the drug permeation flux based on the gel conformation data, graft density, characteristics of the micro-porous support, and drug concentrations and diffusivities in water and in the PNIPAAm gel. The model can successfully estimate the drug permeation flux through the composite with higher (0.42 mg cm⁻²) graft density with a coefficient of determination of 0.95. The discrepancy between the predicted and experimental data at the lower graft density (0.12 mg cm⁻²) was ascribed to pore channel narrowing resulting from the uneven polymer chain distribution.     

Temperature and pH dual-responsive coatings of oligoperoxide-graft-poly(N-isopropylacrylamide): Wettability, morphology, and protein adsorption

Poly(N-isopropylacrylamide) (PNIPAM) coatings attached to glass with novel approach involving polymerization from oligoperoxide grafted to surface with (3-aminopropyl)triethoxysilane exhibit not only temperature- but also pH-dependence of wettability and protein adsorption. Wettability and composition of coatings, fabricated with different polymerization times, were determined using contact angle measurements and Time Of Flight-Secondary Ion Mass Spectrometry (TOF-SIMS), respectively. Thermal response of wettability, measured between 20 and 40 °C, was prominent at pH 9 and 7 and diminished or absent at pH 5 and 3. This indicates a transition between hydrated loose coils and hydrophobic collapsed chains that is blocked at low pH. Higher surface roughness and dramatically increased adsorption of model protein (lentil lectin labeled with fluorescein isothiocyanate) were observed with AFM and fluorescence microscopy to occur in hydrophobic phases (at pH 3, for pH varied at constant temperature of 22 °C and at ∼33 °C, for temperature varied at constant pH 9). Protein adsorption response to pH was confirmed by TOF-SIMS and Principal Component Analysis.     

Salt addition effect on partition coefficient of some phenolic compounds constituents of olive mill wastewater in 1-octanol-water system at 298.15 K

The 1-octanol-water partition coefficient is an important property to measure the hydrophobicity of organic compounds, which has been demonstrated to be a parameter in studying the conformation of biomolecules in aqueous solutions. For biological systems, electrolytes play an important role in thermodynamic properties. The salt addition effect on the distribution of phenolic compounds between water and 1-octanol at 298.15 K has been studied. The phenolic compounds used were vanillic acid, protocatechuic acid, vanillin, tyrosol, cathecol, caffeic acid and syringic acid, and the considered salts were potassium chloride, sodium chloride and lithium chloride. The influence of both the concentration and size of the added salt on the partition coefficient (K _ow) have been considered. This study shows a salting in with the following decreasing order: LiCl > NaCl > KCl. The Gibbs energies of transfer of phenolic compounds (168–1) form chloride solutions to organic phase have been calculated using experimental 1-octanol-water partition coefficients.     

The kinetics of poly(N-isopropylacrylamide) microgel latex formation

Conversion versus time curves were measured for poly(N-isopropylacrylamide) microgel latexes prepared by polymerization in water with sodium dodecyl sulfate, SDS. Polymerization rates increased with temperature with methylenebisacrylamide crosslinking monomer consumed faster thanN-isopropylacrylamide. The particle diameter decreased with increasing concentrations of SDS in the polymerization recipe and there was evidence that the rate of polymerization increased somewhat with SDS concentration. Particle formation occurred by homogeneous nucleation as micelles were absent.Comparison of particle size distributions from dynamic light scattering to those from a centrifugal sizer led to the conclusion that larger particles within a specific latex were less swollen with acetonitrile than were the smaller ones. This was interpreted as evidence for the polymer in larger particles having a higher crosslink density. Particle swelling was estimated from swelling ratios defined as the particle volume at 25 °C divided by the volume at 50 °C. In the absence of crosslinking poly(N-isopropylacrylamide) linear chains would disolve at 25 °C. The swelling results indicated that the average crosslink density in the particles decreased with conversion. This was explained by the observation that the methylenebisacrylamide was consumed more quickly and is typical of crosslinking in emulsion polymerization where polymer particles have high polymer concentrations at their birth.     

Polymeric cation-exchange monolithic columns containing phosphoric acid functional groups for capillary liquid chromatography of peptides and proteins

Two different monoliths, both containing phosphoric acid functional groups and polyethylene glycol (PEG) functionalities were synthesized for cation-exchange chromatography of peptides and proteins. Phosphoric acid 2-hydroxyethyl methacrylate (PAHEMA) and bis[2-(methacryloyloxy)ethyl] phosphate (BMEP) were reacted with polyethylene glycol diacrylate (PEGDA) and polyethylene glycol acrylate (PEGA), respectively, in 75-μm i.d. UV-transparent fused-silica capillaries by photo-initiated polymerization. The hydrophobicities of the monoliths were evaluated using propyl paraben under reversed-phase conditions and synthetic peptides under ion-exchange conditions. The resulting monoliths exhibited lower hydrophobicities than strong cation-exchange monoliths previously reported using PEGDA as cross-linker. Dynamic binding capacities of 31.2 and 269 mg/mL were measured for the PAHEMA–PEGDA and BMEP–PEGA monoliths, respectively. Synthetic peptides were eluted from both monoliths in 15 min without addition of acetonitrile to the mobile phase. Peak capacities of 50 and 31 were measured for peptides and proteins, respectively, using a PAHEMA–PEGDA monolith. The BMEP–PEGA monolith showed negligible hydrophobicity. A peak capacity of 31 was measured for the BMEP–PEGA monolith when a 20-min salt gradient rate was used to separate proteins. The effects of functional group concentration, mobile phase pH, salt gradient rate, and hydrophobicity on the retention of analytes were investigated. Good run-to-run [relative standard deviation (RSD) < 1.99%] and column-to-column (RSD < 5.64) reproducibilities were achieved. The performance of the monoliths in ion-exchange separation of peptides and proteins was superior to other polymeric monolithic columns reported previously when organic solvents were not added to the mobile phase.