Solvent-based de-emulsification dispersive liquid–liquid microextraction combined with gas chromatography–mass spectrometry for determination of trace organochlorine pesticides in environmental water samples

In this work, we propose solvent-based de-emulsification dispersive liquid–liquid microextraction (SD-DLLME) as a simple, rapid and efficient sample pretreatment technique for the extraction and preconcentration of organochlorine pesticides (OCPs) from environmental water samples. Separation and analysis of fifteen OCPs was carried out by gas chromatography–mass spectrometry (GC/MS). Parameters affecting the extraction efficiency were systematically investigated. The detection limits were in the range of 2–50 ng L⁻¹ using selective ion monitoring (SIM). The precision of the proposed method, expressed as relative standard deviation, varied between 3.5 and 10.2% (n = 5). Results from the analysis of spiked environmental water samples at the low-ppb level met the acceptance criteria set by the EPA.     

Dispersive liquid–liquid–liquid microextraction combined with liquid chromatography for the determination of chlorophenoxy acid herbicides in aqueous samples

A novel sample preparation method “Dispersive liquid–liquid–liquid microextraction” (DLLLME) was developed in this study. DLLLME was combined with liquid chromatography system to determine chlorophenoxy acid herbicide in aqueous samples. DLLLME is a rapid and environmentally friendly sample pretreatment method. In this study, 25 μL of 1,1,2,2-tetrachloroethane was added to the sample solution and the targeted analytes were extracted from the donor phase by manually shaking for 90 s. The organic phase was separated from the donor phase by centrifugation and was transferred into an insert. Acceptor phase was added to this insert. The analytes were then back-extracted into the acceptor phase by mixing the organic and acceptor phases by pumping those two solutions with a syringe plunger. After centrifugation, the organic phase was settled and removed with a microsyringe. The acceptor phase was injected into the UPLC system by auto sampler. Fine droplets were formed by shaking and pumping with the syringe plunger in DLLLME. The large interfacial area provided good extraction efficiency and shortened the extraction time needed. Conventional LLLME requires an extraction time of 40–60 min; an extraction time of approximately 2 min is sufficient with DLLLME. The DLLLME technique shows good linearity (r² ≥ 0.999), good repeatability (RSD: 4.0–12.2% for tap water; 5.7–8.5% for river water) and high sensitivity (LODs: 0.10–0.60 μg/L for tap water; 0.11–0.95 μg/L for river water).     

Low-density extraction solvent-based solvent terminated dispersive liquid–liquid microextraction combined with gas chromatography-tandem mass spectrometry for the determination of carbamate pesticides in water samples

A simple and fast method of low-density extraction solvent-based solvent terminated dispersive liquid–liquid microextraction (ST-DLLME) was developed for the highly sensitive determination of carbamate pesticides in the water samples by gas chromatography-tandem mass spectrometry (GC-MSMS). After dispersing, the obtained emulsion cleared into two phases quickly when an aliquot of acetonitrile was introduced as a chemical demulsifier into the aqueous bulk. Therefore, the developed procedure does not need centrifugation to achieve phase separation. It was convenient for the usage of low-density extraction solvents in DLLME. Under the optimized conditions, the limits of detection for all target carbamate pesticides were in range of 0.001–0.50 ng mL⁻¹ and the precisions were in the range of 2.3–6.8% (RSDs, 2 ng mL⁻¹, n = 5). The proposed method has been successfully applied to the analysis of real water samples and good spiked recoveries over the range of 94.5–104% were obtained.     

Dispersive liquid–liquid microextraction followed by gas chromatography–mass spectrometry for the rapid and sensitive determination of UV filters in environmental water samples

The performance of the dispersive liquid–liquid microextraction (DLLME) technique for the determination of eight UV filters and a structurally related personal care species, benzyl salicylate (BzS), in environmental water samples is evaluated. After extraction, analytes were determined by gas chromatography combined with mass spectrometry detection (GC-MS). Parameters potentially affecting the performance of the sample preparation method (sample pH, ionic strength, type and volume of dispersant and extractant solvents) were systematically investigated using both multi- and univariant optimization strategies. Under final working conditions, analytes were extracted from 10 mL water samples by addition of 1 mL of acetone (dispersant) containing 60 μL of chlorobenzene (extractant), without modifying either the pH or the ionic strength of the sample. Limits of quantification (LOQs) between 2 and 14 ng L⁻¹, inter-day variability (evaluated with relative standard deviations, RSDs) from 9% to 14% and good linearity up to concentrations of 10,000 ng L⁻¹ were obtained. Moreover, the efficiency of the extraction was scarcely affected by the type of water sample. With the only exception of 2-ethylhexyl-p-dimethylaminobenzoate (EHPABA), compounds were found in environmental water samples at concentrations between 6 ± 1 ng L⁻¹ and 26 ± 2 ng mL⁻¹.     

Dispersive liquid–liquid microextraction followed by high-performance liquid chromatography for the determination of three carbamate pesticides in water samples

A simple, rapid and efficient method, dispersive liquid–liquid microextraction (DLLME) in conjunction with high-performance liquid chromatography (HPLC), has been developed for the determination of three carbamate pesticides (methomyl, carbofuran and carbaryl) in water samples. In this extraction process, a mixture of 35 µL chlorobenzene (extraction solvent) and 1.0 mL acetonitrile (disperser solvent) was rapidly injected into the 5.0 mL aqueous sample containing the analytes. After centrifuging (5 min at 4000 rpm), the fine droplets of chlorobenzene were sedimented in the bottom of the conical test tube. Sedimented phase (20 µL) was injected into the HPLC for analysis. Some important parameters, such as kind and volume of extraction and disperser solvent, extraction time and salt addition were investigated and optimised. Under the optimum extraction condition, the enrichment factors and extraction recoveries ranged from 148% to 189% and 74.2% to 94.4%, respectively. The methods yielded a linear range in the concentration from 1 to 1000 µg L^?1 for carbofuran and carbaryl, 5 to 1000 µg L^?1 for methomyl, and the limits of detection were 0.5, 0.9 and 0.1 µg L^?1, respectively. The relative standard deviations (RSD) for the extraction of 500 µg L^?1 carbamate pesticides were in the range of 1.8–4.6% (n = 6). This method could be successfully applied for the determination of carbamate pesticides in tap water, river water and rain water.     

Analysis of carbamate pesticides in water samples using single-drop microextraction and gas chromatography–mass spectrometry

Single-drop microextraction (SDME) followed by gas chromatography–mass spectrometry detection was used for the determination of some carbamate pesticides in water samples. The studied pesticides were thiofanox, carbofuran, pirimicarb, methiocarb, carbaryl, propoxur, desmedipham and phenmedipham. Two alternative sample introduction methods have been examined and compared; SDME followed by cool on-column injection (without derivatization) and SDME followed by in-microvial derivatization and splitless injection. Acetic anhydride was used as derivatization reagent. Parameters that affect the derivatization reaction yield and the extraction efficiency of the SDME method were studied and optimized. The analytical performances and possible applications of both approaches were investigated. Relative standard deviations for the studied compounds ranged from 3.2 to 8.3%. The detection limits obtained by the derivatization method were found to be in the range 3–35 ng/L. Using cool on-column injection (without derivatization), the detection limits were between 30 and 80 ng/L.     

Nonequilibrium hollow-fiber liquid-phase microextraction with in situ derivatization for the measurement of triclosan in aqueous samples by gas chromatography–mass spectrometry

Hollow-fiber liquid-phase microextraction (HF-LPME), a relatively new sample preparation technique, has attracted much interest in the field of environmental analysis. In the current study, a novel method based on hollow-fiber liquid-phase microextraction with in situ derivatization and gas chromatography–mass spectrometry for the measurement of triclosan in aqueous samples is described. Hollow-fiber liquid-phase microextraction conditions such as the type of extraction solvent, the stirring rate, the volume of derivatizing reagent, and the extraction time were investigated. When the conditions had been optimized, the linear range was found to be 0.05–100 μg l⁻¹ for triclosan, and the limit of detection to be 0.02 μg l⁻¹. Tap water and surface water samples collected from our laboratory and Wohushan reservoir, respectively, were successfully analyzed using the proposed method. The recoveries from the spiked water samples were 83.6 and 114.1%, respectively; and the relative standard deviation (RSD) at the 1.0 μg l⁻¹ level was 6.9%.     

Dispersive liquid–liquid microextraction combined with high-performance liquid chromatography–tandem mass spectrometry for the identification and the accurate quantification by isotope dilution assay of Ochratoxin A in wine samples

A novel approach for the rapid analysis of ochratoxin A (OTA) in wine samples is presented. Mycotoxin was extracted and concentrated from matrix using dispersive liquid–liquid microextraction (DLLME). The final extract is analyzed by liquid chromatography coupled to positive electrospray ionization tandem mass spectrometry employing [²H₅]-ochratoxin A as internal standard. Some important parameters, such as the nature and volume of extraction solvent and dispersive solvent, and salt effect were investigated and optimized to achieve the best extraction efficiency and higher enrichment factor. Under the optimum extraction condition, the method provided enrichment factor around 80 times and showed a high sensitivity with method detection and quantification limits of 0.005 and 0.015 ng mL⁻¹, respectively. To test the accuracy of the analytical procedure, the optimized method was applied to the analysis of reference material T1755 (naturally contaminated white wine), with excellent results (accuracy of 103%) and showing a good precision with a CV (n = 6) of 5.8%. The proposed method, which is demonstrated to be quick, cheap, accurate and highly selective, was successfully applied to the analysis of Italian wines.     

Coacervative microextraction ultrasound-assisted back-extraction technique for determination of organophosphates pesticides in honey samples by gas chromatography–mass spectrometry

Coacervative microextraction ultrasound-assisted back-extraction technique (CME-UABE) is proposed for the first time for extracting and preconcentrating organophosphates pesticides (OPPs) from honey samples prior to gas chromatography–mass spectrometry (GC–MS) analysis. The extraction/preconcentration technique is supported on the micellar organized medium based on non-ionic surfactant. To enable coupling the proposed technique with GC, it was required to back extract the analytes into hexane. Several variables including, surfactant type and concentration, equilibration temperature and time, matrix modifiers, pH and buffers nature were studied and optimized over the relative response of the analytes. The best working conditions were as follows: an aliquot of 10 mL 50 g L⁻¹ honey blend solution was conditioned by adding 100 μL 0.1 mol L⁻¹ hydrochloric acid (pH 2) and finally extracted with 100 μL Triton X-114 100 g L⁻¹ at 85 °C for 5 min using CME technique. Under optimal experimental conditions, the enrichment factor (EF) was 167 and limits of detection (LODs), calculated as three times the signal-to-noise ratio (S/N = 3), ranged between 0.03 and 0.47 ng g⁻¹. The method precision was evaluated over five replicates at 1 ng g⁻¹ with RSDs ≤9.5%. The calibration graphs were linear within the concentration range of 0.3–1000 ng g⁻¹ for chlorpirifos; and 1–1000 ng g⁻¹ for fenitrothion, parathion and methidathion, respectively. The coefficients of correlation were ≥0.9992. Validation of the methodology was performed by standard addition method at two concentration levels (2 and 20 ng g⁻¹). The recoveries were ≥90%, indicating satisfactory robustness of the methodology, which could be successfully applied for determination of OPPs in honey samples of different Argentinean regions. Two of the analyzed samples showed levels of methidathion ranged between 1.2 and 2.3 ng g⁻¹.     

Dispersive liquid–liquid microextraction method based on solidification of floating organic drop for extraction of organochlorine pesticides in water samples

A new simple and rapid dispersive liquid–liquid microextraction method has been developed for the extraction and analysis of organochlorine pesticides (OCPs) in water samples. The method is based on the solidification of a floating organic drop (DLLME-SFO) and is combined with gas chromatography/electron capture detection (GC/ECD). Very little solvent is required in this method. The disperser solvent (200 μL acetonitrile) containing 10 μL hexadecane (HEX) is rapidly injected by a syringe into the 5.0 mL water sample. After centrifugation, the fine HEX droplets (6 ± 0.5 μL) float at the top of the screw-cap test tube. The test tube is then cooled in an ice bath. After 5 min, the HEX solvent solidifies and is then transferred into a conical vial, where it melts quickly at room temperature, and 1 μL of it is injected into a gas chromatograph for analysis. Under optimum conditions, the enrichment factors and extraction recoveries are high and range between 37–872 and 82.9–102.5%, respectively. The linear range is wide (0.025–20 μg L⁻¹), and the limits of detection are between 0.011 and 0.11 μg L⁻¹ for most of the analytes. The relative standard deviation (RSD) for 1 μg L⁻¹ of OCPs in water was in the range of 5.8–8.8%. The performance of the method was gauged by analyzing samples of lake and tap water.     

Rapid determination of amide herbicides in environmental water samples with dispersive liquid–liquid microextraction prior to gas chromatography–mass spectrometry

This paper describes a novel, simple and environmentally friendly method for rapid determination of the amide herbicides metoalchlor, acetochlor, and butachlor. It is based on dispersive liquid-liquid microextraction and gas chromatography–mass spectrometry. Factors that may influence the enrichment efficiency, such as type and volume of extraction solvent, type and volume of dispersive solvent, extraction time, and content of NaCl, were investigated and optimized in detail. Under the optimum conditions, the limits of detection of metoalchlor, acetochlor, and butachlor were 0.02, 0.04, and 0.003 μg L⁻¹, respectively. The experimental results indicated that there was linearity over the range 0.1–50 μg L⁻¹ and good reproducibility with relative standard deviations over the range 1.6–3.0% (n = 5). The proposed method has been applied for the analysis of real-world water samples, and satisfactory results were achieved. Average recoveries of spiked herbicides were in the range 80.3–108.8%. All of these indicated that the developed method would be an efficient method for simultaneous determination of the three herbicides in environmental water samples.     

Application of SiO2 hollow fibers for sorptive microextraction and gas chromatography–mass spectrometry determination of organochlorine pesticides in herbal matrices

A method involving simultaneous extraction and sample clean-up procedure: hollow fiber sorptive microextraction, coupled with gas chromatography–mass spectrometric detection for quantification of seven organochlorine pesticides in Radix et Rhizoma Rhei is described. SiO₂ hollow fiber with porous structure was synthesized for the first time. The internal diameter of SiO₂ hollow fiber is 380 μm and average wall thickness is 100 μm. Aggregated SiO₂ particles deposited on the surface of the hollow fiber in a regular array lead to porous structure. SiO₂ hollow fiber was applied to the determination of organochlorine pesticides in Radix et Rhizoma Rhei to avoid sample clean-up and minimize the matrix effects. Extraction solvent, extraction temperature and equilibration time were optimized. Fiber to fiber repeatability over the concentration ranges were less than 10%. Recoveries were satisfactory (between 63% and 115%) for most of organochlorine pesticides at spiking levels. Furthermore, the proposed method was also applied to determine seven organochlorine pesticides in 43 commercial Radix et Rhizoma Rhei samples, in which the selected pesticides were found in eight samples. The results have been further confirmed by solvent extraction methods according to China Pharmacopoeia (2005).     

Application of dispersive liquid–liquid microextraction followed by gas chromatography/mass spectrometry as effective tool for trace analysis of organochlorine pesticide residues in honey samples

A dispersive liquid–liquid microextraction (DLLME) method followed by gas chromatography/mass spectrometry (GC/MS) was applied for the trace determination of organochlorine pesticides in honey samples. The type and volume of organic extraction and disperser solvents, pH, effect of added salt content and centrifuging time and speed were optimized to find the appropriate extraction conditions. In DLLME, 30 µL of 1,2-dibromomethane (serving as extractant) and 1.5 mL of acetonitrile (serving as disperser) were applied. The limit of detection (3 s) and limit of quantification (10 s) for all the analytes of interest (organochlorine pesticides) varied from 0.004 to 0.07 and from 0.02 to 0.3 ng g^?1, respectively. The extraction recovery ranged from 91 to 100 %, and the enrichment factors ranged from 171 to 199. The relative standard deviation was <6 % for intraday (n = 6) and <8 % interday (n = 4) measurements. The proposed DLLME–GC/MS method was confirmed to be fast, simple to perform, friendly to environment and suitable for analysis of organochlorine pesticide residues at trace levels in honey samples.     

Dispersive liquid–liquid microextraction combined with high performance liquid chromatography-DAD detection for the determination of sulfonylurea herbicides in water samples

A new method for the determination of four sulfonylurea herbicides (metsulfuron-methyl, chlorsulfuron, bensulfuron-methyl and chlorimuron-ethyl) in water samples was developed by dispersive liquid–liquid microextraction coupled with high performance liquid chromatography-diode array detector. Parameters that affect the extraction efficiency, such as the kind and volume of the extraction and disperser solvent, extraction time and salt addition, were investigated and optimised. Under the optimum conditions, the enrichment factors were in the range between 102 and 216. The linearity of the method was obtained in the range of 1.0–100 ng mL^?1 with the correlation coefficients (r) ranging from 0.9982 to 0.9995. The method detection limits were 0.2–0.3 ng mL^?1. The proposed method has been successfully applied to the analysis of target sulfonylurea herbicides in river, stream and well water samples with satisfactory results.     

Development of ultrasound-assisted emulsification microextraction for the determination of seven pesticides in apple juice by gas chromatography–mass spectrometry

Α simple, relatively rapid, sensitive and cost-effective method based on ultrasound-assisted emulsification microextraction (USAEME) followed by gas chromatography coupled with mass spectrometry has been developed for the determination of seven endocrine disruptor pesticides (chlorpyrifos, deltamethrin, dimethoate, fenitrothion, malathion, pendimethalin and procymidone) in apple juice. This approach is based on the emulsification of organic extraction solvent in a diluted apple juice sample by ultrasound radiation and further separation of both liquids phases by centrifugation. The influence of the different parameters affecting the procedure (extraction solvent, extraction solvent volume, ultrasound time, centrifugation time, ionic strength and pH) was evaluated in order to optimise the efficiency of the extraction process. Target analytes were extracted from a 0.5 g apple juice sample that was diluted by 10 times with aqueous buffer solution (pH 7). The optimised USAEME procedure used 100 μL of chloroform as extraction solvent, 8 min of ultrasound extraction, ionic strength (2.5% w/v) and 7.5 min of centrifugation at 3800 rpm. The optimised method presented recoveries between 70 and 113% for the target analytes. Acceptable linearity for all target analytes was recorded with correlation coefficients (r) higher than 0.992. The limits of quantification were found between 1.1 and 4.6 μg kg^?1 ensuring compliance with the maximum residue limits established by the European Commission. The proposed method was applied for the determination of the endocrine disruptor pesticides in apple samples proving its suitability to the Commission Implementing Regulation (EU) no. 400/2014.     

Pre-concentration of phenolic compounds in water samples by novel liquid–liquid microextraction and determination by gas chromatography–mass spectrometry

Pre-concentration and determination of 8 phenolic compounds in water samples has been achieved by in situ derivatization and using a new liquid–liquid microextraction coupled GC–MS system. Microextraction efficiency factors have been investigated and optimized: 9 μL 1-undecanol microdrop exposed for 15 min floated on surface of a 10 mL water sample at 55 °C, stirred at 1200 rpm, low pH level and saturated salt conditions. Chromatographic problems associated with free phenols have been overcome by simultaneous in situ derivatization utilizing 40 μL of acetic anhydride and 0.5% (w/v) K₂CO₃. Under the selected conditions, pre-concentration factor of 235–1174, limit of detection of 0.005–0.68 μg/L (S/N = 3) and linearity range of 0.02–300 μg/L have been obtained. A reasonable repeatability (RSD ≤ 10.4%, n = 5) with satisfactory linearity (0.9995 ≥ r² ≥ 0.9975) of results illustrated a good performance of the present method. The relative recovery of different natural water samples was higher than 84%.     

Multi-residue determination of organochlorine pesticides in vegetables in Kirklareli,Turkey by gas chromatography–mass spectrometry

The aim of this study was to investigate the level of organochlorine pesticides use for treatment of tomatoes, eggplants and cucumbers in Kirklareli, Turkey. Eighteen organochlorine pesticides were identified in vegetable samples using microwave or Soxhlet extraction, and results were obtained by gas chromatography–mass spectrometry. The optimized conditions were 1 mL/min for flow rate in the mobile phase, 1 μL for injection volume and 70 V for fragmentation potential. The analytical parameters show that the microwave oven extraction procedure provided the best results when compared to the Soxhlet extraction procedure. Samples were prepared for analysis with hexane?dichlormethane (1: 1, v/v, 40 mL) using a solid-phase extraction method. The limits of detection and quantitation for the eighteen analytes were between 0.02–0.26 and 0.06–0.87 μg/L, respectively, and the relative standard deviations of the migration time ranged from 2.4 to 8.9%. The recoveries of surrogate spiked in vegetable samples ranged from 70 to 116%, respectively. The obtained concentrations of pesticides in all vegetables studied were proved in the range of ND–123 μg/kg. The organochlorine pesticide sum was below the legal limit, except for Endrin and Methoxychlor, which requires a further elucidation of the organochlorine pesticides pollution sources in the region. These studies on accumulation of organochlorine pesticides were necessary for accomplishing a comprehensive ecological risk assessment.     

Dispersive liquid–liquid microextraction combined with flow injection inductively coupled plasma mass spectrometry for simultaneous determination of cadmium, lead and bismuth in water samples

Dispersive liquid–liquid microextraction (DLLME) was combined with flow injection inductively coupled plasma mass spectrometry for simultaneous determination of cadmium, lead and bismuth in water samples. The metal elements were complexed with sodium diethyldithiocarbamate, and then the complexes were extracted into carbon tetrachloride by using DLLME. Under the optimized conditions, the enrichment factors for Cd, Pb and Bi are 460, 900 and 645 in 5 mL of a spiked water sample, respectively. The calibration graphs for the three metals are linear in the range of concentrations from <10 ng L^?1 to 1,000 ng L^?1. The detection limits are 0.5 ng L^?1, 1.6 ng L^?1 and 4.7 ng L^?1, respectively. The relative standard deviations for ten replicate measurements of 50 ng L^?1 cadmium, lead and bismuth are 2.6%, 6.7%, and 4.9%, respectively, and the relative recoveries in various water samples at a spiking level of 50 ng L^?1 range from 83.6% to 107.0%.     

Low-density magnetofluid dispersive liquid–liquid microextraction for the fast determination of organochlorine pesticides in water samples by GC-ECD

A new micro-extraction technique named low-density magnetofluid dispersive liquid–liquid microextraction (LMF-DMMLE) has been developed, which permits a wider range of solvents and can be combined with various detection methods. Comparing with the existing low density solvents micro-extraction methods, no special devices and complicated operations were required during the whole extraction process. Dispersion of the low-density magnetofluid into the aqueous sample is achieved by using vortex mixing, so disperser solvent was unnecessary. The extraction solvent was collected conveniently with an external magnetic field placed outside the extraction container after dispersing. Then, the magnetic nanoparticles were easily removed by adding precipitation reagent under the magnetic field. In order to evaluate the validity of this method, ten organochlorine pesticides (OCPs) were chosen as the analytes. Parameters influencing the extraction efficiency such as extraction solvents, volume of extraction solvents, extraction time, and ionic strength were investigated and optimized. Under the optimized conditions, this method showed high extraction efficiency with low limits of detection of 1.8–8.4 ng L⁻¹, good linearity in the range of 0.05–10.00 μg L⁻¹ and the precisions were in the range of 1.3–9.6% (RSD, n = 5). Finally, this method was successfully applied in the determination of OCPs in real water samples.