潮流中污染物离散的理论分析与应用

利用浓度矩法推导了纵向流速分布可分离为空间函数与时间函数相乘型式的二维潮汐流动中剪切离散系数的表达式,获得了对数流速分布下正弦式潮汐流离散系数随时间的变化过程,对离散与潮流特征的关系以及负离散问题进行了分析。最后将理论分析成果应用于珠江黄埔河段,获得了与实测资料相符的结果。     

HIGH-ORDER-ACCURATE DISCRETIZATION STENCIL FOR AN ELLIPTIC EQUATION

The coefficients for a nine-point high-order-accurate discretization scheme for an elliptic equation ∇²u− γ²u=r₀ (∇² is the two-dimensional Laplacian operator) are derived. Examples with Dirichlet and Neumann boundary condtions are considered. In order to demonstrate the high-order accuracy of the method, numerical results are compared with exact solutions.     

叶栅可压缩流场的数值分析

将一维ＡＵＳＭ＾＋格式与三阶精度ＭＵＳＣＬ格式融合,给出了其在任意风线坐标下的二维形式,采用有限体积法,将ＡＵＳＭ＾＋格式与Ｒｕｎｇｅ－Ｋｕｔｔａ格式结合,对叶栅可压缩流场进行了数值模拟,典型算例的计算结果与有关献结果相符很好,表明ＲＫ－ＡＵＳＭ＾＋混合格式对叶栅可压缩流场进行数值模拟是可行的。     

内分液结构调控竖直管间歇流型建模研究

内分液流型调控管依靠微尺度网孔阻气通液的毛细力学特性,调控气液两相间歇流型以实现传热强化.基于Lockhart-Martinelli 分相模型以及Zuber-Findlay 漂移流动模型,建立描述内分液竖直管内流体动力特性的一维数学模型. 采用模型求解实验工况,计算结果与实验结果误差均在20% 以内. 计算发现,液速对流动现象起决定作用,而气速影响通过丝网的渗透程度. 在定性分析基础上,采用三角立方插值与最小二乘B 样条拟合获得了流动特性与气速、液速的定量函数关系. 据此得出结论,当Re_l < 693 7 时,一定出现第1 类工况;当Re_l > 693 7,且Re_g < 67 时,可能会出现第2 类工况,此时较低的气速会促进第2 类工况的出现. 根据建立的模型与拟合关系式可实现内分液调控管的优化设计.      

竖直管道中固-液两相流动流态化实验探讨

主要探讨竖直管道中不同颗粒级配、流体流速条件下的固-液两相流动的流态化规律.首先通过量纲分析获得关键控制参数,然后以玻璃珠(粒径:0.25mm~2.0mm)、粉细砂(d10=0:044mm)两种固体和水为实验介质,开展了两相流动流态化实验,考虑流体流速(相对于管道雷诺数介于640~3300之间)和颗粒级配的影响.通过分析发现:具有均匀粒径分布的玻璃珠床,床层膨胀高度随流速的增加而增加,流速与浓度的对数呈线性关系,与Richardson-Zaki公式一致;具有较宽粒径分布的粉细砂,细颗粒随水流逐渐流出管道,剩余颗粒质量与雷诺数呈指数递减趋势.     

NUMERICAL STUDY OF EFFECTS OF PULSATILE AMPLITUDE ON UNSTEADY LAMINAR FLOWS IN RIGID PIPE WITH RING-TYPE CONSTRICTIONS

The effects of pulsatile amplitude on sinusoidal laminar flows through a rigid pipe with sharp-edged ring-type constrictions have been studied numerically. The parameters considered are: mean Reynolds number (Re) of the order of 100; Strouhal number (St) in the range 0·0–3·98; Womersley number (Nw) in the range 0·0–50·0. The pulsatile amplitude (A) varies in the range 0·0–2·0. The flow characteristics were studied through the pulsatile contours of streamline, vorticity, shear stress and isobars. Within a pulsatile cycle the relations between instantaneous flow rate (Q) and instantaneous pressure gradient (dp/dz) are observed to be elliptic. The relations between instantaneous flow rate (Q) and pressure loss (P_loss) are quadratic. Linear relations exist between instantaneous flow rate (Q) and maximum velocity, maximum vorticity and maximum shear stress. © by 1997 John Wiley & Sons, Ltd.     

垂直湍流液-固流中大颗粒的相对速度

通过量纲分析和实验测量,对于垂直、局部均匀的湍流稀态液一固流中,大颗粒的相对速度,建立了无量纲参数表达式．用分析和实验相结合的方法,确定了表达式中无量纲参数的幂次及有关系数．实验中用激光多普勒分相测量技术,分别测出流体和颗粒的时均速度结果表明,大颗粒相对速度强烈依赖于流体雷诺数,当流体雷诺数较高时,其幂次渐近于1.5。     

张量方程在三维粘性绕流计算中的应用

本文采用张量形式的粘性激波层方程,用空间推进的数值方法计算了球锥、椭球锥有攻角高超音速绕流问题,并计算了组合椭球锥的粘性绕流,从而说明了本文的方法可推广应用于一般外型飞行器的小攻角绕流计算问题。文中考虑了在高超音速流动条件下空气的非平衡化学反应,认为化学反应的速率是有限的     

火炮制退机流场的数值模拟

利用Rodi ASM模型和SIMPLER计算程式对接近于实际结构的制退机流场做了数值模拟,获得了制退机湍流流场的结构,并对数值模拟结果进行了分析,数值模拟结果揭示了制退机流场中存在流动截面收缩现象。     

MODELING TWO-PHASE FLOW IN PULSED FLUIDIZED BED

Mathematical models for pulsed fluidization are systematically discussed. Several undetermined constitutive relationships are included in the General Two-Fluid Model (GTFM), the adjustable parameters of which are always chosen at will to some extent. Although there are no adjustable parameters in the Basic Two-Fluid Model (BTFM), its eigenvalues are complex numbers and it is ill-posed for initial-value problems. The Local Equilibrium Model (LEM), a further simplification of BTFM, is discussed at length. Although the model is very simple, it is highly capable of simulating complex processes in pulsed fluidization over a broad range of operating parameters, and its numerical results well fit experimental results in both the variation of bed height and the distribution of particle concentration as fluidizina velocitv varies.     

MODEL VERIFICATION ON 3D TIDAL CURRENT ANALYSIS IN TOKYO BAY

The results of a research project to verify the newly improved multiple- level model for 3D tidal current analysis in Tokyo Bay are presented. The improved multiple-level model includes additional effects due to Coriolis force, river inflows and wind shear stresses. Furthermore, a new numerical treatment of the open boundary condition was applied which effectively eliminated the spurious reflective waves often generated by various numerical methods simulating free surface flows. The mean (time-averaged or residual) and tidal currents in Tokyo Bay were simulated as examples to demonstrate the validity and capability of the newly improved multiple-level model. A series of numerical experiments was conducted to carefully examine the tidal circulations affected by the forcing factors of Coriolis force, river inflows and wind shears, both individually and combined. The numerical results demonstrated that the effects of each forcing term are physically reasonable, with the wind shear effect being the most significant and the case including all forcing terms being in best overall agreement with the field data collected in Tokyo Bay by the Ministry of Transportation. This study has contributed not only to the verification of the newly improved multiple-level model but also to the enhancement of the accuracy of numerical simulations of three-dimensional flow in coastal waters by this model.     

谈谈渗流

渗流是流体在多孔介质中的流动,渗流现象广泛地存在于自然界、工程材料、动物、植物中。多孔介质种类繁多,包括岩石(含各类矿藏)、土壤、生物材料和人工多孔介质材料等。渗流理论已经成为人类开发地下水、地热、石油、天然气、煤炭与煤层气等诸多地下资源的重要理论基础。本文从渗流的基本概念、渗流的分类、渗流的影响因素、渗流的特征以及渗流的研究意义等方面进行了阐述。     

分支流理论研究进展

分支流技术具有广泛的工程应用背景和理论价值．本文分析研究了多孔管摩擦系数、动量交换系数等分支流基础性实验数据，回顾综述了分支流的理论模型、计算方法，以及研究中遇到的主要问题，并介绍了分支流理论的最新进展和今后的研究重点     

ON FLOW IN POROUS MEDIA

渗流是流体在多孔介质中的流动,渗流现象广泛地存在于自然界、工程材料、动物、植物中。多孔介质种类繁多,包括岩石(含各类矿藏)、土壤、生物材料和人工多孔介质材料等。渗流理论已经成为人类开发地下水、地热、石油、天然气、煤炭与煤层气等诸多地下资源的重要理论基础。本文从渗流的基本概念、渗流的分类、渗流的影响因素、渗流的特征以及渗流的研究意义等方面进行了阐述。     

绕流直接数值模拟误差分析

对于无边界绕流问题的计算流体力学模拟通常是将物体置于“足够大”的槽道中,而通过不断改变槽道尺寸以及离散网格密度,后验对比方式来检查模拟误差。本文结合多种经典流场理论,提出一种简单的先验误差估计方法来确定槽道尺寸以及相应的网格分布。在此方法中,对于槽道尺寸的确定基于线性叠加原理（即在极小雷诺数下采用Stokes理论解叠加,而在其他雷诺数条件下采用势流理论解叠加）,来估计槽道尺寸对绕流结果的影响。而对网格尺寸与分布,则是使用多项式逼近中的基本误差分析工具,应用到速度边界层,远场势流,以及Rankine涡等简单流动,从而确定整个绕流问题中的离散误差。为了验证前面的理论分析结果,本文模拟了相当大雷诺数范围内的二维翼型以及三维圆球绕流,所得数值结果非常好地验证了理论分析。结果表明,对于Stokes流动问题,槽道尺寸需要大约100倍于物体特征尺寸来保证其结果与无边界绕流相差不超过1%;而在雷诺数超过大约100时,槽道尺寸只需10倍（二维绕流）或者5倍（三维绕流）于物体特征尺寸来达到同等精度。在此先验误差估计方法可应用于一般化的绕流问题。

     

几何构型对流动聚焦生成微液滴的影响

流动聚焦型微流控装置能够方便、高效地生成均一度好且大小精确可调的微液滴(气泡),故被广泛应用于颗粒材料合成、药物封装、细胞培养等诸多领域. 进一步优化通道结构有助于实现对合成微粒粒径、均一度和尺寸范围的精确调控. 本文数值研究了通道深度、缩颈段长度以及两相夹角等几何构型因素对流动聚焦生成微液滴直径及其生成周期各个阶段的影响. 控制液滴生成方式为滴流式,发现液滴直径随通道深度d 的增加近似呈线性增大,且当通道深度小于30 μm 时,随着通道深度的下降,微液滴生成周期在毛细力的强烈作用下出现骤升,通道深度超过80 μm 时,微液滴的生成周期基本接近恒定. 连续相和离散相的夹角θ接近90°时,液滴直径及其生成周期最短,夹角太大或太小均不利于生成均一度好且粒径微小可控的液滴. 调整缩颈段长度l引起液滴直径及其生成周期的变化幅度仅为其平均值的3%~5% 左右. 此外,缩颈段宽度也是影响流动聚焦生成微液滴直径及其生成周期的重要因素,在通道深度固定时,缩颈段越宽,微液滴直径及其生成周期越大.      

NUMERICAL SIMULATIONS OF HYDRODYNAMIC BEHAVIORS IN CONICAL SPOUTED BEDS

The axial and radial distributions of static pressures and vertical particle velocities of conical spouted beds have been simulated and compared with experimental data. Simulation results show that, among all factors investigated, the Actual Pressure Gradient (the APG term) in conical spouted beds, introduced as the default gravity term plus an empirical axial solid phase source term, has the most significant influence on static pressure profiles, followed by the restitution coefficient and frictional viscosity, while other factors almost have no effect. Apart from the solid bulk viscosity, almost all other factors affect the radial distribution of the axial particle velocity, although the influence of the APG term is less significant. For complex systems such as conical spouted beds where a fluidized spout region and a defluidized annulus region co-exist, the new term introduced in this work can improve the CFD simulation. Furthermore, for other systems with the Actual Pressure Gradient different from either fluidized beds or packed beds, the new approach can also be applied.     

管内充分发展流动与传热数值模拟的教学方法探讨

由于缺乏数值计算的基础理论知识,工科本科生在学习流体流动与传热过程的数值模拟方法并进行程序设计时,往往觉得难度较大。本文围绕圆管内不可压缩流体充分发展流动与传热,采用边界层积分法,推导出无量纲控制方程组;针对层流工况和湍流工况,开发出相应的数值方法。基于该方法的程序代码易于理解,且计算结果表明该方法具有预测精度高、收敛速度快的优点。本文的工作可以为计算流体力学、数值传热学及热工计算等系列课程的本科教学提供参考。

     

单裂缝中携砂液流动规律研究

裂缝中携砂液流动是一种固液两相流,携砂液的运移与支撑剂的铺置是水力压裂裂缝保持导流能力的关键. 本文基于FLUENT 流体计算软件,采用双流体模型,将颗粒看作拟流体,携砂液按照牛顿流体处理,分析了支撑剂体积分数αs、阿基米德数Ar、颗粒雷诺数Re以及裂缝入口边界对流动规律的影响. 研究结果表明：携砂液在裂缝中的流动过程中,发展成为支撑剂体积分数不同的四个区域,包括砂堤区、颗粒悬浮区、颗粒滚流区和无砂区;支撑剂的沉降程度随着支撑剂体积分数和阿基米德数的增加而增加,而随着雷诺数增加而降低;入口为网眼型时,进入裂缝后过流面积的增加导致流速突降,使得支撑剂更容易在入口处产生堆积,在同一入口流速下,较均匀入口的工况铺砂高度大.     

NUMERICAL SIMULATIONS OF HYDRODYNAMIC BEHAVIORS IN CONICAL SPOUTED BEDS

The axial and radial distributions of static pressures and vertical particle velocities of conical spouted beds have been simulated and compared with experimental data. Simulation results show that, among all factors investigated, the Actual Pressure Gradient （the APG term） in conical spouted beds, introduced as the default gravity term plus an empirical axial solid phase source term, has the most significant influence on static pressure profiles, followed by the restitution coefficient and frictional viscosity, while other factors almost have no effect. Apart from the solid bulk viscosity, almost all other factors affect the radial distribution of the axial particle velocity, although the influence of the APG term is less significant. For complex systems such as conical spouted beds where a fluidized spout region and a defluidized annulus region co-exist, the new term introduced in this work can improve the CFD simulation. Furthermore, for other systems with the Actual Pressure Gradient different from either fluidized beds or packed beds, the new approach can also be applied.