On the topological bifurcation of flows around a rotating circular cylinder

Flow fields around a rotating circular cylinder in a uniform stream are computed using a low dimensional Galerkin method. Reslts show that the formation of a Fopple vortex pair behind a stationary circular cylinder is caused by the structural instability in the vicinity of the saddle located at the rear of the cylinder. For rotating cylinder a bifurcation diagram with the consideration of two parameters, Reynolds numberRe and rotation parameter α, is built by a kinematic analysis of the steady flow fields. The project supported by the National Natural Science Foundation of China     

NUMERICAL STUDY ON THE FLOW AROUND A CIRCULAR CYLINDER WITH SURFACE SUCTION OR BLOWING USING VORTICITY-VELOCITY METHOD

A vorticity-velocity method was used to study the incompressible viscous fluid flow around a circular cylinder with surface suction or blowing. The resulted high order implicit difference equations were effeciently solved by the modified incomplete LU decomposition conjugate gradient scheme (MILU-CG). The effects of surface suction or blowing ' s position and strength on the vortex structures in the cylinder wake, as well as on the drag and lift forces at Reynoldes number Re = 100 were investigated numerically. The results show that the suction on the shoulder of the cylinder or the blowing on the rear of the cylinder can effeciently suppress the asymmetry of the vortex wake in the transverse direction and greatly reduce the lift force; the suction on the shoulder of the cylinder, when its strength is properly chosen , can reduce the drag force significantly , too.     

Computation of high Reynolds number flow around a circular cylinder with surface roughness

Incompressible high-Reynolds-number flows around a circular cylinder are analyzed by direct integration of the Navier-Stokes equations using finite-difference method. A generalized coordinate system is used so that a sufficient number of grid points are distributed in the boundary layer and the wake. A numerical scheme which suppresses non-linear instability for calculations of high-Reynolds-number flows is developed. The computation of an impulsively started flow at Re = 1200 is compared with corresponding experimental observations, and excellent agreements are obtained.A series of computations are carried out on the flow around a circular cylinder with surface roughness. The height of the roughness in these computations is 0.5% of the diameter. The range of Reynolds numbers is from 10³ to 10⁵; no turbulence model is employed. Sharp reduction of drag coefficient is observed near Re = 2 × 10⁴, which indicates that the critical Reynolds number is captured in the present computation.     

Mixed convection cooling of a heated circular cylinder by laminar upward-directed slot jet impingement

An experimental and numerical study has been carried out to investigate the heat transfer characteristics of a horizontal circular cylinder exposed to a slot jet impingement of air. A square-edged nozzle is mounted parallel with the cylinder axis and jet flow impinges on the bottom of the cylinder. The study is focused on low Reynolds numbers ranging from 120 to 1,210, Grashof numbers up to Gr = 10Re ² and slot-to-cylinder spacing from 2 to 8 of the slot width. The flow field is greatly influenced by the slot exit velocity and the buoyancy force due to density change. A Mach–Zehnder Interferometer is used for measurement of local Nusselt number around the cylinder at 10° interval. It is observed that the average Nusselt number decreases with increasing the jet spacing and increases with rising the Reynolds number. A finite volume method utilizing a curvilinear coordinate transformation is used for numerical modeling. The numerical results show good agreement with the experimental results. The flow and thermal field are seen to be stable and symmetric around the cylinder over the range of parameters studied.     

Unsteady characteristics of the cavity flow around a rough circular cylinder

Effects of surface roughness on the unsteady cavitating flow around a two-dimensional circular cylinder were experimentally investigated at Reynolds numbers from 1.36 × 10⁵ to 1.78 × 10⁵. Two patterns of surface roughness were investigated, a double-cut pattern and a single-cut pattern. The cavity elongates with an increase of the surface roughness, especially in supercavitating flow. However, for some roughness parameters tested, the cavity length exhibits an extreme decrease. In a particular case of the double-cut pattern, there exists the minimum cavity behind the cylinder.     

Formation of vortex street and vortex pair from a circular cylinder oscillating in water

The flow around a circular cylinder undergoing sinusoidal oscillating movement in still water is investigated by phase-locked PIV measurements. The pattern and development of large-scale vortex structures in the flow are studied from the velocity vectors and vorticity contours obtained at eight successive phases of an oscillating cycle. Experiments are performed at three Keulegan–Carpenter numbers; KC=12, 6.28 and 4.25. Results at KC=12 reveal the mechanism of vortex formation and the development of the shed vortices into a vortex street at a lateral direction to the line of cylinder movement. The role of a biased flow stream and the length of the cylinder stroke in the formation of the vortex street are discussed. At the lower KC numbers, a symmetric pair of vortices is found attached to the leeward face of the cylinder. The vortex pair exhibits an increasing degree of asymmetry when KC increases from 4.25 to 6.28. An explanation in terms of the length of the cylinder strokes and the degree of flow asymmetry is offered for the transition of flow regimes from a vortex pair to a vortex street. The present results are compared with the observations made in previous experimental and numerical studies in the literature.     

An application of the finite difference‐based lattice Boltzmann model to simulating flow‐induced noise

This paper presents a novel approach to simulate aerodynamically generated sounds by modifying the finite difference‐based lattice BGK compressible fluid model for the purpose of speeding up the calculation and also stabilizing the numerical scheme. With the model, aerodynamic sounds generated by a uniform flow around a two‐dimensional circular cylinder at Re = 150 are simulated. The third‐order‐accurate up‐wind scheme is used for the spatial derivatives, and the second‐order‐accurate Runge–Kutta method is applied for the time marching. The results show that we successively capture very small acoustic pressure fluctuations, with the same frequency of the Karman vortex street, much smaller than the whole pressure fluctuation around a circular cylinder. The propagation velocity of the acoustic waves shows that the points of peak pressure are biased upstream owing to the Doppler effect in the uniform flow. For the downstream, on the other hand, it is faster. It is also apparent that the amplitude of sound pressure is proportional to r^?1/2, r being the distance from the centre of the circular cylinder. Moreover, the edgetone generated by a two‐dimensional jet impinging on a wedge to predict the frequency characteristics of the discrete oscillations of a jet‐edge feedback cycle is investigated. The jet is chosen long enough to guarantee the parabolic velocity profile of the jet at the outlet, and the edge is of an angle of α = 23°. At a stand‐off distance w, the edge is inserted along the centreline of the jet, and a sinuous instability wave with real frequency is assumed to be created in the vicinity of the nozzle exit and to propagate towards the downstream. We have succeeded in capturing small pressure fluctuations resulting from periodic oscillation of jet around the edge. Copyright © 2006 John Wiley & Sons, Ltd.     

Numerical simulation of Reynolds number effects on velocity shear flow around a circular cylinder

Three-dimensional Direct Numerical Simulation (DNS) and Large Eddy Simulation (LES) are performed to investigate the shear effects on flow around a circular cylinder at Reynolds numbers of Re=60–1000. The shear parameter, β, which is based on the velocity gradient, cylinder diameter and upstream mean velocity at the center plane of the cylinder, varies from 0 to 0.30. Variations of Strouhal number, drag and lift coefficients, and unsteady wake structures with shear parameter are studied, along with their dependence on Reynolds number. The presented simulation provides detailed information for the flow field around a circular cylinder in shear flow. This study shows that the Strouhal number exhibits no significant variation with shear parameter. The stagnation point moves to the high-velocity side almost linearly with shear parameter, and this result mainly influences the aerodynamic forces acting on a circular cylinder in shear flow. Both the Reynolds number and shear parameter influence the movement of the stagnation point and separation point. Mode A wake instability is suppressed into parallel vortex shedding mode at a certain shear parameter. The lift force increases with increasing shear parameter and acts from the high-velocity side to the low-velocity side. In addition, a simple method to estimate the lift force coefficient in shear flow is provided.     

A numerical investigation of the effects of the spanwise length on the 3-D wake of a circular cylinder

The numerical prediction of vortex-induced vibrations has been the focus of numerous investigations to date using tools such as computational fluid dynamics. In particular, the flow around a circular cylinder has raised much attention as it is present in critical engineering problems such as marine cables or risers. Limitations due to the computational cost imposed by the solution of a large number of equations have resulted in the study of mostly 2-D flows with only a few exceptions. The discrepancies found between experimental data and 2-D numerical simulations suggested that 3-D instabilities occurred in the wake of the cylinder that affect substantially the characteristics of the flow. The few 3-D numerical solutions available in the literature confirmed such a hypothesis. In the present investigation the effect of the spanwise extension of the solution domain on the 3-D wake of a circular cylinder is investigated for various Reynolds numbers between 40 and 1000. By assessing the minimum spanwise extension required to predict accurately the flow around a circular cylinder, the infinitely long cylinder is reduced to a finite length cylinder, thus making numerical solution an effective way of investigating flows around circular cylinders. Results are presented for three different spanwise extensions, namely πD/2, πD and 2πD. The analysis of the force coefficients obtained for the various Reynolds numbers together with a visualization of the three-dimensionalities in the wake of the cylinder allowed for a comparison between the effects of the three spanwise extensions. Furthermore, by showing the different modes of vortex shedding present in the wake and by analysing the streamwise components of the vorticity, it was possible to estimate the spanwise wavelengths at the various Reynolds numbers and to demonstrate that a finite spanwise extension is sufficient to accurately predict the flow past an infinitely long circular cylinder.     

大雷诺数线性剪切流绕圆柱的分离流动

本文采用离散涡方法计算了大雷诺数下线性剪切流绕圆柱的分离流动,计算结果给出阻力系数、横向力系数、边界层分离点、斯特罗哈数及尾流中旋涡的分布图案,计算数据与已有的实验数据相吻合。     

大雷诺数线性剪切流绕圆柱的分离流动

本文采用离散涡方法计算了大雷诺数下线性剪切流绕圆柱的分离流动,计算结果给出阻力系数、横向力系数、边界层分离点、斯特罗哈数及尾流中旋涡的分布图案,计算数据与已有的实验数据相吻合。     

High-order ghost-point immersed boundary method for viscous compressible flows based on summation-by-parts operators

A high-order immersed boundary method is devised for the compressible Navier-Stokes equations by employing high-order summation-by-parts difference operators. The immersed boundaries are treated as sharp interfaces by enforcing the solid wall boundary conditions via flow variables at ghost points. Two different interpolation schemes are tested to compute values at the ghost points and a hybrid treatment is used. The first method provides the bilinearly interpolated flow variables at the image points of the corresponding ghost points and the second method applies the boundary condition at the immersed boundary by using the weighted least squares method with high-order polynomials. The approach is verified and validated for compressible flow past a circular cylinder at moderate Reynolds numbers. The tonal sound generated by vortex shedding from a circular cylinder is also investigated. In order to demonstrate the capability of the solver to handle complex geometries in practical cases, flow in a cross-section of a human upper airway is simulated.     

Numerical predictions for unsteady viscous flow past an array of cylinders

The unsteady two-dimensional flow around an array of circular cylinders submerged in a uniform onset flow is analysed. The fluid is taken to be viscous and incompressible. The array of cylinders consists of two horizontal rows extending to infinity in the upstream and downstream directions. The centre-to-centre distance between adjacent cylinders is fixed at three diameters, and the rows are staggered. Advantage is taken of spatially periodic boundary conditions in the flow direction. This reduces the computational domain to a rectangular region surrounding a single circular cylinder. Two cases, for Reynolds numbers of 1000 and 10,000, are presented.     

A NUMERICAL SIMULATION OF VORTEX SHEDDING FROM AN OSCILLATING CIRCULAR CYLINDER

Vortex shedding from an oscillating circular cylinder is studied by numerical solutions of the two-dimensional unsteady Navier–Stokes equations. A physically consistent method is used for the reconstruction of velocity fluxes which arise from discrete equations for the mass and momentum balances. This method ensures a second-order accuracy. Two phenomena are investigated and, in both cases, the cylinder oscillation is forced. The first is the flow induced by the harmonic in-line oscillation of cylinder in water at rest. The Reynolds number is equal to 100 and the Keulegan–Carpenter number is equal to 5. A comparison of phase-averaged velocity vectors between measurements and predictions is presented. Applying the widely used model of Morison to the computed in-line force history, the drag and the inertia coefficients are calculated and compared for different grid levels. Using these to reproduce the force functions, deviations from those originally computed are revealed. The second problem is an investigation of a transversely oscillating cylinder in a uniform flow at fixed Reynolds number equal to 185. The cylinder oscillation frequency ranges between 0·80 and 1·20 of the natural vortex-shedding frequency, and the oscillation amplitude is 20% of the cylinder diameter. As the frequency of excitation of the cylinder increases relative to the inherent vortex formation frequency, the initially formed concentration of vorticity moves closer to the cylinder until a limiting position is reached. At this point, the vorticity concentration abruptly switches to the opposite side of the cylinder. This process induces distinct changes of the topology of the corresponding streamline patterns.     

NUMERICAL STUDY OF THE BLOCKAGE EFFECTS ON VISCOUS FLOW PAST A CIRCULAR CYLINDER

In various numerical solutions of flow around bluff bodies the unbounded physical domain is replaced by a restricted computational one whose extent depends on the size of the computational grid network. The truncation of the solution domain in the cross-flow direction reduces the computer time required for the solution, but introduces numerical blockage effects which influence considerably the values of the various flow parameters. In the present paper the finite element solution of steady and unsteady flow around a circular cylinder at Re=106 is presented for blockage ratios of 0·05, 0·15 and 0·25. A boundary condition was tested for which the streamfunction values at the outer boundaries were those of the irrotational solution around a circular cylinder. The size of the standing vortices decreases with the blockage ratio when the flow is steady, while the spacing of the vortices decreases in both directions with increasing blockage ratio when the wake becomes unsteady. The hydrodynamic forces on the cylinder and the Strouhal number are magnified as the blockage ratio increases. The application of the streamfunction values derived from the irrotational solution at the outer boundaries reduced blockage effects only at high blockage ratio.     

Higher order finite element methods and multigrid solvers in a benchmark problem for the 3D Navier–Stokes equations

This paper presents a numerical study of the 3D flow around a cylinder which was defined as a benchmark problem for the steady state Navier–Stokes equations within the DFG high‐priority research program flow simulation with high‐performance computers by Schafer and Turek (Vol. 52, Vieweg: Braunschweig, 1996). The first part of the study is a comparison of several finite element discretizations with respect to the accuracy of the computed benchmark parameters. It turns out that boundary fitted higher order finite element methods are in general most accurate. Our numerical study improves the hitherto existing reference values for the benchmark parameters considerably. The second part of the study deals with efficient and robust solvers for the discrete saddle point problems. All considered solvers are based on coupled multigrid methods. The flexible GMRES method with a multiple discretization multigrid method proves to be the best solver. Copyright © 2002 John Wiley & Sons, Ltd.     

Simulation of the flow past a circular cylinder in the supercritical regime by blending RANS and variational-multiscale LES models

A strategy which blends a variational multiscale large eddy simulation (VMS-LES) model and a RANS model in a hybrid approach is investigated. A smooth blending function, which is based on the value of a blending parameter, is used for switching from VMS-LES to RANS. Different definitions of the blending parameter are investigated. The capabilities of the novel hybrid approach are appraised in the simulation of the flow around a circular cylinder at a Reynolds number 1.4×10⁵, based on the freestream velocity and on the cylinder diameter, in the presence of turbulent boundary-layer due to turbulent inflow conditions. A second study at Reynolds numbers from Re=6.7×10⁵ to 1.25×10⁶ is also presented. The effect of using the VMS-LES approach in the hybrid model is evaluated. Results are compared to those of other RANS, LES and hybrid simulations in the literature and with experimental data     

A local domain‐free discretization method for simulation of incompressible flows over moving bodies

This paper presents a local domain‐free discretization (DFD) method for the simulation of unsteady flows over moving bodies governed by the incompressible Navier–Stokes equations. The discretization strategy of DFD is that the discrete form of partial differential equations at an interior point may involve some points outside the solution domain. All the mesh points are classified as interior points, exterior dependent points and exterior independent points. The functional values at the exterior dependent points are updated at each time step by the approximate form of solution near the boundary. When the body is moving, only the status of points is changed and the mesh can stay fixed. The issue of ‘freshly cleared nodes/cells’ encountered in usual sharp interface methods does not pose any particular difficulty in the presented method. The Galerkin finite‐element approximation is used for spatial discretization, and the discrete equations are integrated in time via a dual‐time‐stepping scheme based on artificial compressibility. In order to validate the present method for moving‐boundary flow problems, two groups of flow phenomena have been simulated: (1) flows over a fixed circular cylinder, a harmonic in‐line oscillating cylinder in fluid at rest and a transversely oscillating cylinder in uniform flow; (2) flows over a pure pitching airfoil, a heaving–pitching airfoil and a deforming airfoil. The predictions show good agreement with the published numerical results or experimental data. Copyright © 2010 John Wiley & Sons, Ltd.     

Simulation of a Viscous Flow Around an Oscillating Cylinder at Low Keulegan-Carpenter Numbers

A finite difference simulation method for a viscous flow around a circular cylinder sinusoidally oscillating at low Keulegan-Carpenter numbers is presented. Navier-Stokes equations in finite difference form are solved on a moving grid system, based on a time dependent coordinate transformation. Evolution with time of the flow structures induced by a circular cylinder performing sinusoidal oscillations in a fluid at rest, by means of stream lines, pressure contours and vortex shedding is studied in detail at Keulegan-Carpenter numbers, Kc = 9.4 and 14. The time dependent drag and lift are also explained.     

Vortex shedding and aerodynamic forces on a circular cylinder in linear shear flow at subcritical Reynolds number

Vortex shedding and aerodynamic forces on a circular cylinder in a linear shear flow with its axis normal to the plane of the velocity shear profile at subcritical Reynolds number are investigated experimentally. The shear parameter β, which is based on the velocity gradient, cylinder diameter and upstream mean velocity at the center plane of the cylinder, varies from 0 to 0.27. The Strouhal number has no significant variation with the shear parameter. The time-mean base pressure increases and the fluctuating component of the base pressure decreases significantly with increasing shear parameter. Vortex shedding is suppressed by the velocity shear. Dislocation of the stagnation point takes place and this influences the pressure distribution around the cylinder together with the velocity shear. A mean lift force arises in the shear flow due to asymmetry of the pressure distribution, and it acts from the high velocity side to the low velocity side. In addition, the lift coefficient increases and the drag coefficient decreases with increasing shear parameter.