泡沫聚合法制备超大多孔水凝胶

采用泡沫体系分散聚合法,过硫酸铵(APS)及N,N,N′,N′-四甲基乙二胺(TMEDA)为氧化还原引发体系,N,N′-亚甲基双丙烯酰胺(MBA)为交联剂,碳酸钠为发泡剂,聚氧化乙烯-氧化丙稀(PF127)为泡沫稳定剂,用羧甲基纤维素钠(CMC)接枝丙烯酸(AA)和2-丙烯酰胺基-2-甲基丙磺酸(AMPS)合成了CMC-g-(AA-co-AMPS)超大多孔水凝胶。通过FTIR、SEM表征,表明材料是具有超大多孔结构的CMC-g-(AA-co-AMPS)水凝胶。对各影响因素的研究表明,在m(CMC)∶m(AA)∶m(AMPS)为1∶4∶1,w(APS)为0.8%[其中m(APS)∶m(TMEDA)=2∶1],w(Na2CO3)=65%,w(PF127)=0.2%,温度为65℃时,制得的凝胶吸蒸馏水倍率可达1281g/g,吸0.9%盐水倍率达143g/g,10min时已基本达到溶胀平衡。     

泡沫分散聚合法制备超大孔水凝胶及其性能研究

采用泡沫分散聚合法,以自制的4-乙酰基丙烯酰乙酸乙酯(AAEA)和2-丙烯酰胺基-2-甲基丙磺酸(AMPS)、丙烯酸(AA)为单体,制备了具有相互贯穿超大孔结构的快速响应型水凝胶.结果表明,引发剂和交联剂用量分别为2.5%和0.6%时平衡溶胀度最高;当以饱和碳酸钠溶液为发泡剂时制得的凝胶孔洞均匀贯穿;凝胶经无水乙醇处理...     

接枝改性羧甲基纤维素对铜离子的吸附研究

将离子型单体丙烯酸(AA)及非离子型单体丙烯酰胺(AM)接枝在羧甲基纤维素(CMC)上,通过协同作用提高材料的吸水性及吸水速率,并研究了其对铜离子的吸附性能.通过傅里叶红外(FTIR)对材料分析表明,从及AM成功接枝在CMC上;对吸附物进行了表面分析,扫描电镜图(SEM)显示吸附物表面有大量颗粒状物质,X射线能谱(XPS)证实材料表面吸附了铜离子;在浓度为10mmol/L的铜离子溶液中,CMC-g-P(AA-co-AM)材料的吸附容量为20.30mmol/g.     

P(AA-co-DMDAAC)/PVA凝胶的制备和吸金性能研究

以丙烯酸(AA)、二甲基二烯丙基氯化铵(DMDAAC)为单体,聚乙烯醇(PVA)为第二网络,通过水溶液聚合法制备P(AA-co-DMDAAC)/PVA半互穿水凝胶(SIPNH)。采用FT-IR、XRD、SEM等对凝胶的结构进行了表征。结果表明,PVA用量为5%时,PVA与P(AA-co-DMDAAC)能形成较完善的半互穿网络结构。探讨了凝胶的抗压缩性能、溶胀/消溶胀性能。结果表明,SIPNH形成的半互穿网络结构可以改善凝胶的抗压缩强度,最大抗压缩强度达到0.37MPa。凝胶的溶胀/消溶胀速率随PVA用量的增加呈下降趋势。着重研究了PVA及氯金酸(HAuCl4)用量对SIPNH吸金能力的影响。结果表明,PVA用量大于5%时,SIPNH的吸金能力明显降低。当HAuCl4浓度为250mg/L时,最大吸附量为108.5mg/g。     

聚乙烯醇/羧甲基壳聚糖共混水凝胶的辐射合成及性能

采用电子加速器辐照法制备了聚乙烯醇(PVA)/羧甲基壳聚糖(CMCH)共混水凝胶;研究了PVA与CMCH的配比、辐照剂量、温度以及pH值对PVA/CMCH共混水凝胶性能的影响.实验发现,PVA与CMCH在辐照剂量为40 kGy、配比为w(PVA)/w(CMCH)=5/1的条件下可得到强度较好的PVA/CMCH共混水凝胶,该水凝胶具有一定的温度和pH敏感性:在5~20℃时具有较高的溶胀率,温度在20℃以上溶胀率较低;水凝胶在pH<4.0和pH>6.0时溶胀率均较大,而当pH为4.0~6.0时溶胀率较小.     

P(AMPS-co-HEMA)凝胶的合成与吸银性能研究

以2-丙烯酰胺基-2-甲基丙磺酸(AMPS)和甲基丙烯酸羟乙酯(HEMA)为单体,N,N′-亚甲基双丙烯酰胺(MBA)为交联剂,过硫酸钾(KPS)为引发剂,采用自由基水溶液聚合法制备P(AMPS-co-HEMA)共聚凝胶,通过傅里叶红外光谱(FT-IR)对材料结构进行了表征.研究单体配比、交联剂的用量、引发剂的用量对共聚凝胶吸水性能的影响,并在此基础上对凝胶的溶胀、吸银及消溶胀性能进行研究.结果表明,当单体摩尔比n(AMPS)∶n(HEMA)=2∶1,交联剂用量ω(MBA)=0.6％,引发剂用量ω(KPS)=0.8％,所制得的凝胶吸水性能最好;凝胶在蒸馏水中的溶胀过程属于松弛平衡扩散;凝胶在AgNO3溶液中60min左右达到消溶胀平衡,且当AgNO3溶液的浓度为0.05mol/L时,银离子吸附量最大,为0.04g/g,消溶胀速率最快.     

温度和pH敏感P（NIPA／AA）／黏土互穿网络水凝胶的辐射合成与表征

以N-异丙基丙烯酰胺(NIPA)和丙烯酸(AA)为聚合单体、有机黏土作为改性剂,采用60Co-γ射线为放射源,辐射合成了P(NIPA/AA)/黏土互穿网络(IPN)水凝胶,研究了IPN的表面形貌以及AA浓度、黏土对水凝胶溶胀性能和压缩性能的影响.SEM电镜观察表明:P(NIPA/AA)共聚水凝胶的表面致密,没有明显相分离,而IPN凝胶表面疏松多孔且非连续,有明显的相分离,形成了较好的IPN结构.P(NIPA/AA)IPN水凝胶在碱性和弱碱性溶液中的溶胀率高,且其溶胀速率由网络中高分子链的松弛运动控制;而在酸性介质中,水分子的扩散为水凝胶溶胀的决定过程.P(NIPA/AA)IPN水凝胶具有良好的力学性能,加入黏土后凝胶的压缩性能参数均有不同程度的提高,水凝胶受压时只发生塑性变形,没有被破坏.     

PVA-PAMPS-PAA三元互穿网络型水凝胶的合成及其性能研究

以2-丙烯酰胺基-2-甲基丙磺酸(AMPS)、丙烯酸(AA)以及聚乙烯醇(PVA)为原料,制备了PVA-PAMPS-PAA三元互穿网络型(T-IPN)水凝胶.红外分析表明,PVA与PAA以及PAMPS之间形成了较强的氢键,使得PVA分子上的C—O伸缩震动吸收峰移向了低波数处.X射线衍射以及电镜分析表明,当PVA用量较低时,PVA能均匀的穿插于凝胶网络中,形成完善的互穿网络结构,当PVA用量过高时,部分的PVA结晶而使得凝胶出现相分离.研究了该三元互穿网络型水凝胶的溶胀性能,结果表明,该水凝胶的平衡溶胀比在200至340之间,并且随着AA以及AMPS用量的增加,凝胶的溶胀速率以及平衡溶胀比均升高.该三元互穿网络型水凝胶在酸性溶液中和在碱性溶液中表现出截然不同的消溶胀性能;并且随着溶液pH的升高,凝胶在pH=9.0附近出现体积突变,表现出pH敏感性.通过研究T-IPN水凝胶的抗压缩性能发现,利用线型高分子、柔性高分子网络以及刚性高分子网络制备的三元互穿网络型水凝胶能在高溶胀比下保持较高的强度.溶胀比为180的T-IPN水凝胶,其最大抗压缩强度可达12.1 MPa.进一步研究发现,凝胶的组成以及溶胀比均对凝胶的抗压缩强度和压缩应变均存在较大的影响.     

反相微乳液聚合法制备聚(丙烯酰胺-co-丙烯酸)pH敏感微凝胶及其性能

以丙烯酰胺(AM)和丙烯酸(AA)单体的水溶液为分散相,失水山梨醇单油酸脂(Span80)/聚氧乙烯失水山梨醇脂肪酸脂(Tween80)/异辛烷为分散介质,分别以N,N′-亚甲基双丙烯酰胺(MBA)、过硫酸铵/亚硫酸氢钠((NH4)2S2O8/NaHSO3)为交联剂和氧化还原引发剂,在30℃进行反相微乳液聚合制备了一系列不同单体摩尔百分数的P(AM-co-AA)微凝胶.通过傅立叶红外光谱、浊度法、透射电镜(TEM)和动态光散射(DLS)等测试手段分别对微凝胶特征官能团的存在、pH敏感性、微观形态、粒径大小及粒径分布等进行表征分析.结果表明,共聚物中存在AM和AA结构单元;样品的TEM照片显示在原料中AA的摩尔百分数为60%时,P(AM-co-AA)微凝胶粒子的数均粒径为90 nm左右,呈现非规则球形;DLS结果表明,P(AM-co-AA)微凝胶与PAM微凝胶相比具有较宽的粒径分布,且随原料中AA摩尔百分数增加,粒径分布逐渐变宽;P(AM-co-AA)微凝胶具有良好的pH敏感性,敏感pH值与AA的解离常数有关,通过调节pH值可以迅速控制自身体积的溶胀与收缩.     

聚乙烯醇/丙烯酸共聚物水凝胶的制备及溶胀性

制备了具有pH敏感性的聚乙烯醇(PVA)/丙烯酸(AA)共聚物水凝胶,研究了PVA与AA之间配比、交联剂、引发剂用量对凝胶转化率的影响,对水凝胶的溶胀行为和pH敏感性也进行了详细研究.实验表明PVA与AA的质量比为(1∶9)~(3∶7)之间时,引发剂和交联剂分别为PVA和AA总量的0.2%和0.3%时,凝胶转化率高.随着水溶液pH值从3增加到9,凝胶的溶胀比也相应的增加,表现出明显的pH敏感性.     

大孔PAMPS/PVA半互穿网络型水凝胶的制备及其性能研究

以PEG6000为成孔剂, 合成了大孔聚(2-丙烯酰胺-2-甲基丙磺酸)/聚乙烯醇半互穿网络型(s-IPN)水凝胶. 红外分析表明, PVA与PAMPS之间形成了较强的氢键, 使得PVA分子上的C—O伸缩振动吸收峰移向了低波数处. X射线衍射分析发现, 当PVA用量较高时, 由于部分的PVA结晶, 使得凝胶的半互穿网络结构不均匀. 电镜分析结果表明, 没有使用成孔剂的凝胶表面成褶皱形, 不存在任何孔洞结构; 而以PEG6000为成孔剂的凝胶表面存在相互贯穿的大孔结构. 研究了该水凝胶的溶胀性能, 结果表明, 该水凝胶的平衡溶胀度在116至320之间; 而成孔剂PEG6000的加入能较大幅度提高凝胶的溶胀速率, 凝胶在240 min之内就能达到溶胀平衡. 对凝胶抗压缩性能的研究表明, 当PVA用量为9.1% (w)时, 凝胶的抗压缩强度最大, 可达12.0 MPa; 而成孔剂的加入会在一定程度削弱凝胶的抗压缩强度. 该凝胶具有较好的电场敏感性, 研究发现, 将吸去离子水达到溶胀平衡的凝胶放入施加有电场的0.2 mol&#8226;L－1 NaCl溶液中时, 凝胶迅速偏向阳极. 而PVA和成孔剂PGE6000的用量均对凝胶的偏转速度以及最大偏转角存在较大的影响.     

Chemical–physical behavior of hydrogels of poly(vinyl alcohol) and poly(ethylene glycol)

New hydrogels based on polyethylene glycol (PEG) and poly(vinyl alcohol) (PVA) of different degrees of hydrolysis were synthesized. To form the network the PEG was modified at their ends with acyl chloride groups to be used as the crosslinking agent. The compositions of the hydrogels were between 50% and 90% by weight of PEG and PVA of various degrees of hydrolysis were used. It was found that the degree of hydrolysis of the PVA and the PEG content influence the equilibrium water content of the hydrogel. The process of swelling of all the hydrogels prepared followed a second-order kinetics.     

Impacts of some macromolecules on the characteristics of hydrogels prepared from pineapple peel cellulose using ionic liquid

Composite hydrogels were prepared from pineapple peel cellulose with the combinations of polyethylene glycol (PEG), polyvinyl alcohol (PVA), к-carrageenan (CN), or soluble starch (SH) in 1-allyl-3-methylimidazolium chloride solvent. Impacts of these macromolecules on the texture profile analysis (TPA) parameters, equilibrium swelling ratio (ESR), and sodium salicylate (NaSA) load of the prepared hydrogels were studied. The NaSA release kinetics of the composite hydrogels were also compared. The composite hydrogels exhibited differences in Fourier transform infrared spectroscopy (FTIR), TPA parameters, ESR, NaSA load ratio, and release kinetics. CN addition increased the hardness of the hydrogels, while PEG played an opposite role. SH and PVA could decrease hardness, gumminess, and resilience, and SH could increase the springiness and cohesiveness of the hydrogels. Most of the composite hydrogels exhibited the same basic FTIR features as the simple hydrogel. Freeze-dried composite hydrogels exhibited a markedly higher ESR than the oven-dried ones, and additions of PEG, PVA, CN, and SH showed the same effect. Addition of the PEG and PVA combination could lower the ESR of the hydrogels, whereas additions of the PEG and CN combination or PEG and SH combination could markedly increase the ESR of the hydrogels. Addition of PEG, PVA, CN, and SH respectively could increase the NaSA load ratio of the hydrogels. Oven-drying treatment, additions of the PEG and PVA combination or PEG and CN combination were propitious for extending the NaSA fast-release phase of the hydrogels.     

A novel method to prepare microporous and nanofibrous hydrogel scaffolds as neural tissue engineering

A new method to prepare poly (vinyl alcohol) hydrogels by nebulization method.is introduced. A blend of Poly (vinyl alcohol) (PVA), sodium gum malate (SGM) and cellulose nanofibers (CNFs) originated from Catha Edulis was prepared and tested as neural tissue substitutes. Glutaraldehyde (GLA) was used as a crosslinker. Presence of SGM and CNFs in the formulation improved the nebulization process of PVA solution as well as mechanical properties of the fabricated hydrogels. The tensile strength of neat PVA films attains 46.7 MPa, while the tensile strength was 94.23 MPa for crosslinked-PVA. The tensile strength was found to increase with the increase in the CNFs content in the PVA compared with PVA/SGM. These soft tissues were characterized by using FTIR, SEM, and DSC. Scanning electron microscopy (SEM) results showed that PVA/SGM/CNFs blends has a diameter about 50 ± 8µm. The hydrogels were tested also for antimicrobial activities against pathogenic bacteria like Candida albicans (fungus), Bacillus subtilis (G + Ve), Staphylococcus aureus (G + Ve), Proteus vulgaris (G ? Ve) and Erwinia carotovora (G ? Ve). Favorable mechanical, thermal properties and biodegradation nature of the hydrogels, as well as antimicrobial property indicate that prepared hydrogels are suitable for tissue engineering applications.     

Etude rheologique de gels mixtes de poly(alcool vinylique) et d'alginate de sodium

Snake-cage hydrogels were prepared by the association of poly(vinyl alcohol) (PVA) and sodium alginate. The aim of this work is to study the viscoelastic properties of PVA networks having different molecular weights and trapping alginates of various mannuronate/guluronate ratios, molecular weights and aqueous concentration. The elastic and viscous moduli, G′ and G″, were found to depend on alginate concentration. With the sodium alginate (mannuronate/guluronate =1.78, M̄w=380 000), the elasticity was observed to be independent of the PVA molecular weight in the 7.5% to 10% (w/w) concentration range. Hydrogels elasticity was found to be sodium alginate nature-dependent only in the case of PVA with M̄w =22 000. Moreover, it seems that the viscoelastic parameters G′ and G″ become increasingly insensitive to the nature of sodium alginate as the molecular weight of PVA increases.     

PVA改性PAMPS-PAM超高力学性能双网络水凝胶的制备

采用紫外光引发聚合制备了聚乙烯醇(PVA)改性的聚(2-丙烯酰胺基-2-甲基丙磺酸)-聚丙烯酰胺(PAMPS-PAM)双网络(DN)水凝胶.测定并比较了PVA改性前后PAMPS-PAM双网络水凝胶的溶胀动力学;通过扫描电子显微镜(SEM)观察了单网络水凝胶的结构;测定PVA改性前后PAMPS-PAM双网络水凝胶的压缩及拉伸性能.结果表明,经PVA改性后的PAMPS-PAM双网络水凝胶有较高的溶胀比;0.82%PVA用量的PAMPS-PAM双网络水凝胶在90%压缩形变率下仍保持完整、最大拉伸应力达到0.5 MPa,大幅提高PAMPS-PAM双网络水凝胶的力学性能.     

Preparation and characterization of PVA/SA/HA composite hydrogels for wound dressing

A composite hydrogel based on, by introducing, polyvinyl alcohol, sodium alginate, and hyaluronic acid was fabricated using CaCl₂ as a cross-linker. The physical properties including morphology, water vapor transmission rate, and hydrophilicity were investigated. All PVA/SA/HA composite hydrogels with different compositions had highly homogeneous and interconnected pores, and the morphologies of the PVA/SA/HA hydrogels ranged from fibrous structure to irregular structure with increasing content of SA. The introduction of sodium alginate enhanced the hydrophilicity and water vapor transmission capacity of the hydrogel; however, the hydrophilicity of the composite hydrogels decreased with the increasing cross-linker content.     

快速响应的温敏性聚(N-异丙基丙烯酰胺)水凝胶 Ⅱ.热力学行为及水的状态研究

对使用CaCO3为成孔剂合成的快速响应的温敏性聚 (N 异丙基丙烯酰胺 ) (PNIPA)水凝胶进行了热力学行为和水的状态研究 .热力学研究表明 ,多孔结构的PNIPA水凝胶的平衡膨胀比随着反应物中CaCO3含量的增加而增加 ,随着交联剂浓度的增加而显著减小 ,但相转变温度均不受影响 .在水溶液中加入NaCl则使PNIPA水凝胶的相转变温度 (LCST)线性减小 .利用DSC分析了水凝胶中水的存在状态 ,证明了上述多孔PNIPA水凝胶中存在三种不同状态的水 ,研究了不同CaCO3粒子含量和离子强度对三种不同状态水的影响     

淀粉-丙烯酸钠接枝共聚物的固体高分辨核磁共振研究

运用固体高分辨核磁共振技术,通过测量13C魔角旋转/交叉极化(CP/MAS)谱、1H自旋-晶格弛豫时间T1及旋转坐标系中的自旋-晶格弛豫时间T1ρ,对一系列淀粉-丙烯酸钠接枝共聚物的相结构进行了研究,并与淀粉、均聚丙烯酸钠及两者共混物的实验结果进行了比较.结果表明,接枝共聚导致了淀粉结晶度的明显降低;在共混物和接枝共聚物中,淀粉和聚丙烯酸钠组分都具有纳米尺度的相容性,由于接枝的效应,接枝共聚物中两个组分表现出比共混物更高的相容水平.     

Synthesis and Properties of Hydrogels Based on Chitosan and Poly(Vinyl Alcohol) Crosslinked by Genipin

Semi‐interpenetrating polymeric networks of chitosan and poly(vinyl alcohol) [PVA] were prepared by varying the ratio of the constituents. The hydrogels were crosslinked using genipin, a naturally occurring nontoxic cross‐linking agent. The swelling behavior of these hydrogels was studied by immersing the films in deionized water at various temperatures and in buffer solutions of different pH. The states of water in the hydrogels, swollen at 25°C and pH 7, were determined using Differential Scanning Calorimetry (DSC). The swelling behavior of the gels was found to be dependent on temperature and pH of the medium. The amount of freezing water in the swollen hydrogels increased, whereas the amount of nonfreezing bound water remained more or less the same with increasing PVA concentration.