300 Femtosecond pulses at 497 nanometer generated by an excimer laser pumped cascade of distributed feedback dye lasers

The setup is a cascade of 3 lasers: A competing cavity dye laser pumped by a XeCl excimer laser, followed by two distributed feedback dye lasers. The typical durations of the pulses from the lasers are 100 ps, 5 ps, and 300 fs, respectively. The output pulses at 497 nm are amplified up to 500 MW. The shortest pulse duration obtained was 198 fs.     

分布反馈光纤激光器阵列中外腔反馈特性研究

以半导体激光器中的复合腔模型和实测的分布反馈光纤激光器的外腔端面反射率为基础,对不同反射率条件下分布反馈光纤激光器的输出功率进行了仿真,同时搭建了二基元分布反馈光纤激光器阵列实验平台,对仿真结果进行了验证.仿真与实验结果表明:外腔反馈光重新注入分布反馈光纤激光器会增加激光器的输出功率,降低了阵列的输出功率平坦性.并且外腔端面反射率越大,这种平坦性降低的效果越明显.在构建分布反馈光纤激光器阵列时,应考虑外腔反馈对阵列输出功率平坦性造成的影响,尽量选择外腔端面反射率较小的激光器进行组阵.     

Modeling a distributed feedback dye laser pumped by a Nd-glass laser

A mathematical model has been developed to describe the dynamic emission of a distributed feedback dye laser (DFDL) pumped by a Nd-glass laser. The model is based on the coupled-wave theory. It allows the investigation of the temporal behavior of the Nd-glass pumping laser source and the DFDL pulses. The model allows studying the effect of the variation of the laser input parameters of the Nd-glass laser, such as maximum amplification coefficient, loss coefficient and pumping rate on the characteristics of DFDL pulses regarding the pulse width, delay time and separation time. The feedback process of the DFDL is provided either by changes of the refractive index or by optical gain or by both together. The model estimates the following: temporal behavior of the density of emitted radiation, energy densities of the first excited singlet and triplet states, DFDL output power, cavity decay time and the temperature of the produced grating. The numerical solution of the nonlinear coupled rate equation system predicts the generation of DFDL picosecond pulses. The calculated results are in good agreement with the available experimental data. The calculations were done using rhodamine 6G dissolved in ethanol as the investigated matrix.     

抑制相位噪声实现主动锁模光纤激光器稳定工作

腔长漂移是引起主动锁模光纤激光器不稳定的一个主要原因。通过理论分析得出了主动锁模光纤激光器输出脉冲相位噪声和腔长漂移的关系，并采用抑制相位噪声的方法实现了主动锁模光纤激光器长达８小时的稳定工作。     

新型电光陶瓷调Q光纤激光器

报道了基于OptoCeramic(R)电光陶瓷材料的新型调Q光纤激光器.采用976 nm半导体激光器作为抽运源,电光陶瓷调制器作为Q开关,峰值吸收系数1200 Db/m的高掺杂镱纤作为增益介质构成环形腔激光器.增益光纤的高掺杂浓度使得激光器的腔长得到缩短,输出光脉冲的宽度得到压缩.通过调节电光元件的电压,控制材料的折射率,调节谐振腔的损耗,实现Q开关作用.实验中通过改变腔长、抽运功率和重复频率,研究了脉冲的输出特性.获得最窄脉宽104 ns,重复频率3～40 kHz连续可调的调Q脉冲输出.     

闪耀光栅外腔反馈压窄半导体激光器线宽技术的研究

在讨论半导体激光线宽压窄理论的基础上,利用闪耀光栅作为外部反馈元件,介绍了由中心波长为949.6nm、原始线宽为1.2THz的单管半导体激光器构成的反馈外腔,它能够很好的改善半导体激光器的性能。实验得到了中心波长稳定的、单纵模的高质量激光输出,边模抑制比大于30dB,线宽优于1.2MHz(Δλ<3.6×10-6nm)。实验证实了强反馈能够很好地改善外腔半导体激光器的动态特性。     

激光器内腔频差对双折射外腔激光回馈系统输出影响的理论及实验研究

玻璃材料的内应力关系及所在系统的稳定性、安全性和可靠性,是精密加工领域的重要问题.基于双折射外腔激光回馈效应的应力测量技术以其先进新颖的测量原理受到普遍关注.传统理论普遍认为双折射回馈系统中激光器的输出相位仅由外腔相位延迟决定,而将测量误差归因于外腔镜的非线性运动.本文结合正交偏振激光原理和三镜腔等效模型,测量了激光器的内腔双折射引起的频差大小,进行了频率调谐回馈实验,并根据结论计算了内腔频差对外腔相位延迟测量结果的影响,发现激光器的输出相位由外腔相位延迟、内腔频差、外腔长度共同决定.本文总结了内腔和外腔各向异性共同作用下激光器正交偏振态的相位特性,补充了激光回馈的物理内容,对于应力-双折射、位移、距离等重要参量的精确测量,都具有重要指导意义.     

Stable multigigahertz pulse-train formation in a short-cavity passively harmonic mode-locked erbium/ytterbium fiber laser

We demonstrate a short-cavity erbium-ytterbium fiber laser that is passively mode locked by a saturable Bragg reflector with a fundamental repetition rate of 235 MHz . The laser operates in the soliton regime and under passive harmonic mode locking with 11 pulses in the cavity and produces output pulse trains at 2.6 GHz with transform-limited 270-fs pulses and 1.6 mW of average power. Within the cavity the multiple pulses form a stable pattern with fixed, nearly equal pulse-to-pulse temporal spacings, causing the output pulse train to have timing offsets of less than 15 ps. A slow gain-recovery model is proposed to explain the pulse-train self-organization.     

Mathematical modeling of ruby laser as a pumping source of a “self Q-switched” distributed feedback dye laser

A mathematical model describing the dynamic emission of the ruby laser as a pumping source of a distributed feedback dye laser (DFDL) has been adapted. The suggested model allows the temporal behavior investigation of the ruby laser and the DFDL on mode characteristics and, moreover, investigating the affect of laser input parameters on the output laser pulses in the ruby laser and in the DFDL.The numerical solutions of a coupled nonlinear rate equations system of the adapted model that predict the generation of picoseconds pulses, with neglecting the effect of refractive index variation, are discussed (feedback process is achieved only by optical gain). The model estimates the density of the emitted radiation, energy density of the first excited state, and the output power of the DFDL. The adapted mathematical model is in good agreement with the available experimental data.     

激光二极管自混合干涉的计算分析和实验观察

实验上观察到自混合干涉信号的幅度仅仅为静态光强的百分之几.反馈光会引起激光二极管阈值电流减小,静态输出光强变化几倍,使激光二极管工作在实际的阈值电流之上.按三镜法布里-珀罗腔结构模型计算激光二极管的出射光强,由干涉函数主极大条件得出光频与反馈光的关系.计算出的自混合干涉信号的波形,以及自混合干涉信号的幅度与静态光强的比值均同实验测量结果一致.在τrC/τ1=22.8的情况下,复合谐振腔可同时有15个谐振模式,这些模随外腔长度的变化小于2.6×10-2cm-1,远小于法布里-珀罗谐振腔谐振模的线宽3.1cm-1,光频在内腔谐振模的线宽以内变化.     

半导体激光器混沌输出的延时特征和带宽

外腔延时特征和带宽是影响混沌激光应用的两个重要参量.本文将一个单路光反馈的半导体激光器输出的激光部分地注入到另一个双路滤波光反馈的半导体激光器中,从而构成一个具有外光注入的双路滤波光反馈半导体激光器系统,即主从激光器系统,用于抑制混沌激光的延时特征并研究其带宽.数值研究了外光注入系数、反馈强度、抽运因子和滤波器带宽对系统输出混沌激光的延时特征的影响,然后将该系统对延时特征的抑制效果和具有外光注入的单路光反馈半导体激光器系统、具有外光注入的双路光反馈半导体激光器系统、具有外光注入的单路滤波光反馈半导体激光器系统以及无光注入双路滤波光反馈半导体激光器系统进行对比和分析,结果表明本文提出的方案对延时特征的抑制效果最好.然后在本文提出的具有外光注入的双路滤波光反馈半导体激光器系统中,延时特征被有效抑制的参数条件下研究系统输出混沌激光的带宽,结果表明,通过适当选择参数的取值,本文提出的方案可以提高系统输出混沌激光的带宽.     

双光反馈半导体激光混沌系统的外腔反馈强度对延时特征的影响

通过构建一个双光反馈半导体激光混沌系统,本文实验研究了双腔之间不同反馈强度对系统混沌输出的延时特征的影响.结果表明:固定一个腔的反馈量,而适当调节另一个腔的反馈强度,可实现对混沌输出延时特征的良好抑制.同时,在延时反馈特征抑制较好的情况下,还存在时间漂移（即从混沌输出所提取的特征延时与系统真实延时之差）明显增大的现象.因此采用双光反馈半导体系统可以很好地隐藏激光混沌的延时参量,从而显著提升其在相关领域的表现性能.     

Laser Intensity Variation in Amplitude and Phase Induced by Elliptically Polarized Feedback

The laser output characteristics under elliptically polarized optical feedback effect are studied. Elliptically polarized light is generated by wave plate placed in the feedback cavity. By analyzing the amplitude and phase of the laser output in the orthogonal direction, some new phenomena are firstly discovered and explained theoretically.Elliptically polarized feedback light is amplified in the gain medium in the resonator, and the direction perpendicular to the original polarization direction is easiest to oscillate. The laser intensity variation in amplitude and phase are related to the amplified mode and the anisotropy of external cavity. The theoretical analysis and experimental results agree well. Because the output characteristic of the laser has a relationship with the anisotropy of the external cavity, the phenomenon also provides a method for measuring birefringence.     

外光注入半导体激光器实现时钟分频

从理论和实验上研究了利用光注入半导体激光器对高重复速率光脉冲产生的周期振荡和时钟分频现象.结果表明，光注入半导体激光器引起的二倍周期振荡是使注入脉冲重复频率分频的直接原因.通过耦合速率方程，数值模拟了半导体激光器在外光注入时输出光的时间序列和功率谱，并且分析了激光腔内各种周期振荡的特征.研究表明，当注入光使半导体激光器出现稳定的二倍周期振荡，且注入光的重复频率为此振荡频率的二倍时，时钟分频即可产生实验中，采用重复频率为6.32GHz的光脉冲注入Fabry-Perot激光器，实现了3.16GHz时钟分频信号 关键词： 周期振荡 时钟分频 光谱侧带 光注入     

Self-pulsing in Er3+-doped fibre laser

The output intensity of an erbium-doped fibre laser was studied. Experiments were performed with three pumping wavelengths: 514.5 nm, 810 nm and 980 nm. The laser output intensity exhibits three different dynamical behaviours: steady-state, sinusoidal variation or self-pulsing. In particular, in a bad (high-loss) cavity configuration, when the pumping ratio is increased above the lasing threshold the output intensity changes continuously from a steady-state to an infinite train of pulses. We also show that, depending on the cavity configuration, the transient oscillations display different forms.     

波长可调谐超短光脉冲的简便高质的生成技术

提出了一种以处于增益开关调制状态下的法布里珀罗(Fabry-Pérot)半导体激光器作为光源,采用简单的自激注入锁定方式,以生成波长可调谐的超短光脉冲的实验系统。该实验装置中,激光器的外腔包括两个串联在一起的布拉格光纤光栅,一个掺铒光纤放大器(EDFA),一个光耦合器和两个环行器,其作用是选模,以及增强并控制反馈回激光器内腔的光强。该实验系统简单而高效,在24nm的波长调谐范围内获得了边模抑制比高于40dB的单模光脉冲输出;而在1521.8nm和1550.0nm之间28.2nm的波长调谐范围内,边模抑制比高于35dB。所得到的各个单波长激光脉冲的时域半峰全宽为140~260ps,各个脉冲的光谱半峰全宽皆为0.1nm。     

Compact 10-GHz Nd:GdVO4 laser with 0.5-W average output power and low timing jitter

We demonstrate a compact, diode-pumped Nd:GdVO4 laser with a repetition rate of 9.66 GHz and 0.5-W average output power. The laser is passively mode locked with a semiconductor saturable absorber mirror (SESAM), yielding 12-ps-long sech2-shaped pulses. For synchronization of the pulse train to an external reference clock, the SESAM is mounted on a piezoelectric transducer. With an electronic feedback loop of only a few kilohertz loop bandwidth we achieved a rms timing jitter of 146 fs (integrated from 10 Hz to 10 MHz). This is an upper limit because it is mostly limited by the measurement system. The laser setup with a simple linear cavity has a footprint of only 130 mm x 30 mm.     

Strong intensity variations of laser feedback interferometer caused by atmospheric turbulence

The significant variation of the laser output can be caused by feedback of a small part of laser beam, which is reflected or backscattered by a target at a long distance from laser source, into the laser cavity. This paper describes and analyzes theoretically and experimentally the influence of atmospheric turbulence on interference caused by laser feedback. The influence depends upon both the energy of feedback into the laser cavity and the strength of turbulence over a laser propagation path in the atmosphere. In the case of stronger energy of feedback and weak turbulence variance of fluctuation of the laser output can be enhanced by hundreds to thousands times. From our measurements and theoretical analysis it shows that these significant enhancements can result from the change of laser-cavity-modes which can be stimulated simultaneously and from beat oscillations between a variety of frequencies of laser modes. This also can result from optical chaos inside the laser resonator because a non-separabl     

Experimental investigations on the external cavity time signature in chaotic output of an incoherent optical feedback external cavity semiconductor laser

Chaotic dynamics of a semiconductor laser subject to incoherent optical feedback (IOF) are experimentally investigated, and the external cavity time are retrieved and measured from intensity time series of the laser output by using self-correlation function and the mutual information. Through moderating feedback strength and injection current of the laser, the external cavity time signature of the laser chaotic output is effectively attenuated, and then the security of such chaos encryption system can be assured to a certain degree.     

Dynamics of Semiconductor Lasers with Optical Feedback from Photorefractive Phase Conjugate Mirror

The dynamics of semiconductor lasers with photorefractive phase conjugate optical feedback are experimentally studied. Photorefractive fringes considered here are rather static compared with time fluctuations of laser output power. Therefore, it is expected that a semiconductor laser with photorefractive feedback shows similar dynamics to those with conventional optical feedback. We examine relaxation oscillation and external cavity modes of laser output power in the presence of photorefractive phase conjugate feedback. It is proved that the dynamics of photorefractive phase conjugate feedback are fundamentally the same as those of conventional optical feedback.