具有光催化性能的TiO2-SiO2/TiO2两层增透膜的设计与制备

采用膜层设计理论设计了以TiO₂为内层膜,TiO₂-SiO₂复合膜为外层膜的两层增透膜,以钛酸丁酯（TBOT）和正硅酸乙酯（TEOS）作为前驱体,采用溶胶-凝胶法制备了TiO₂溶胶以及SiO₂溶胶,将两种溶胶按比例混合得到了TiO₂-SiO₂复合溶胶,在高硼硅玻璃上镀膜测试。透过率测试结果表明,在波长为550nm处的透过率最高能达到99.4%。在光催化实验中,采用罗丹明B模拟有机污染物,考察了TiO₂对光催化反应的影响。结果表明,在TiO₂存在的情况下,罗丹明B的降解速度大大提高,光催化效率显著增加。     

疏水介孔二氧化硅膜的制备与表征

用甲基三乙氧基硅烷(MTES)代替部分正硅酸乙酯(TEOS)作为前驱体，以聚乙烯醚-聚丙烯醚-聚乙烯醚三嵌段共聚物(P123)作有机模板剂，通过共水解缩聚反应制备了甲基修饰的介孔SiO₂膜。利用N₂吸附、FTIR、²⁹Si MAS NMR以及接触角测量仪对膜的孔结构和疏水性进行了表征。结果表明，修饰后的膜材料具有良好的介孔结构，最可几孔径为4.65 nm，孔体积为0.69 cm³·g^-1，比表面积为938.4 m²·g^-1；同时疏水性明显提高，当n_MTES/n_TEOS达到1.0时，其对水的接触角达到109°± 1.1°。气体渗透实验表明气体通过膜孔的扩散由努森机制所控制。     

三氟丙基修饰的二氧化硅膜制备、氢气分离及其水热稳定性能

以三氟丙基三甲氧基硅烷(TFPTMS)和正硅酸乙酯(TEOS)作为前驱体,通过溶胶-凝胶法制备三氟丙基修饰的SiO₂膜材料,研究了三氟丙基修饰对膜材料孔结构和疏水性的作用、疏水膜材料的氢气渗透和分离性能以及水热稳定性能。结果表明三氟丙基修饰后的膜材料仍保持良好的微孔结构,孔径狭窄分布在0.45~0.7 nm之间。修饰后膜材料疏水性明显提高,当n_TFPTMS/n_TEOS=0.6时,对水的接触角达到(102.7°±0.1°)。H₂在修饰后膜材料的输运遵循微孔扩散机理,在300 ℃时,H₂的单组份渗透率达到4.77×10^-7 mol·m^-2·s^-1·Pa^-1,H₂/CO₂的理想分离系数以及双组份分离系数分别达到6.99和6.93,均高于其Knudsen扩散分离因子。在200 ℃水蒸气物质的量含量为5%的环境中陈化220 h后,H₂的单组份渗透率仅在前3 h有轻微下降,然后基本保持不变,说明三氟丙基修饰的SiO₂膜具有良好的水热稳定性。     

掺杂纳米SiO2的PVDF-g-PSSA质子交换膜

以聚偏氟乙烯(PVDF)为骨架, 采用溶液接枝苯乙烯磺酸, 合成了掺杂纳米SiO₂颗粒的复合质子交换膜(PVDF/xSiO₂-g-PSSA). 利用红外光谱、热失重分析方法、扫描电镜, 对膜的结构、热稳定性、表面及断面形态进行了表征. 考察了膜的吸水率、电导率、甲醇渗透性等性质. 结果表明, 纳米SiO₂颗粒能提高膜的阻醇性能, 掺杂质量分数10%的适量SiO₂颗粒所得的复合膜的甲醇渗透系数达1.0×10^－7 cm²/s, 低于聚偏氟乙烯接枝苯乙烯磺酸(PVDF-g-PSSA)膜的1.7×10^－7 cm²/s, 仅为Nafion-117的渗透系数的二十分之一. PVDF/10% SiO₂-g-PSSA复合膜具有较高的选择性, 在直接甲醇燃料电池中具有良好的应用前景.     

疏水性对溶胶-凝胶SiO2薄膜抗真空污染及抗激光损伤能力的影响

以正硅酸乙酯作为前驱体, 利用碱催化方式制备了SiO₂溶胶, 通过在溶胶中添加含疏水基团(-CH₃)的六甲基二硅氮烷(HMDS)对溶胶进行改性, 使用添加不同物质的量比HMDS改性后的溶胶用提拉法在K9基片上镀膜, 获得了具有疏水性能的SiO₂薄膜。采用自制接触角测量仪、紫外-可见-近红外分光光度计研究了薄膜的水接触角和透过率。测试了薄膜的激光损伤阈值, 并观察了激光辐照后薄膜的损伤形貌。通过真空污染实验对薄膜的抗污染能力及抗激光损伤能力进行了研究。实验结果表明:经疏水改性的溶胶所镀制的薄膜激光损伤阈值由未改性样品的24.3 J·cm^-2增加到37 J·cm^-2(1 064 nm, 10 ns), 且抗真空污染能力大大加强:在真空环境下保存168 h后, 未改性样品的峰值透过率下降了2%, 而疏水改性后的样品峰值透过率仅下降了0.25%, 并保持了较高的激光损伤阈值(30.8 J·cm^-2)。     

耐环境性SiO2/SiO2-TiO2 增透膜的设计与制备

根据膜层设计理论设计出以K9玻璃为基体的耐环境性的双层增透膜, 这种增透膜在特定波长处具有超高的透过率. 以盐酸为催化剂, 分别以正硅酸乙酯和钛酸丁酯为前驱体制备了SiO2和TiO2溶胶, 将SiO2和TiO2溶胶按一定比例混合得到SiO2-TiO2复合溶胶. 通过改变复合溶胶中SiO2的含量调节复合膜的折射率, 通过改变提拉速度控制薄膜的厚度. 实验结果表明, 双层增透膜在550 nm处的透过率达到99.9%. 增透膜经较强机械摩擦后峰值透过率基本保持不变, 表明该增透膜具有优良的耐摩擦性. 进一步采用六甲基二硅氮烷对增透膜表面进行修饰, 修饰后增透膜的接触角增大至98.3°, 增透膜的疏水性及环境稳定性得到较大提高.     

SiO2/PE/ Bi2S3核壳结构纳米颗粒的合成与性能(英)

以多层电解质作为微型反应器，制备了SiO₂/ Polyelectrolyte(PE) / Bi₂S₃核壳纳米粒子。XRD结果表明Bi₂S₃颗粒属于正交晶系。由透射电镜和场发射扫描电镜照片可知，在直径为640 nm左右的SiO₂表面覆盖了厚度35 nm的Bi₂S₃壳层。红外光谱分析结果表明硅烷网络在结构上发生了变化(SiO₂表面的硅烷醇键沉积在Bi₂S₃的表面)。SiO₂核和SiO₂ / PE / Bi₂S₃的紫外-可见吸收光谱显示在900 nm存在典型吸收边。     

静电纺丝技术制备TiO2@SiO2亚微米同轴电缆与表征

用静电纺丝技术成功制备出大量的TiO₂＠SiO₂亚微米同轴电缆. 用TGA-DTA, XRD, SEM, TEM, EDS, FTIR分析技术对样品结构和组成进行了系统的表征. 结果表明, 得到的产物为TiO₂＠SiO₂亚微米级同轴电缆, 以无定型SiO₂为壳层, 晶态TiO₂为芯层, 电缆平均直径450 nm, 壳层厚度90 nm, 电缆长度＞300 μm, 同时在样品中发现个别纤维呈现管状结构, 对其形成机理进行了讨论.     

静电纺丝技术制备TiO2@SiO2亚微米同轴电缆与表征

用静电纺丝技术成功制备出大量的TiO₂＠SiO₂亚微米同轴电缆. 用TGA-DTA, XRD, SEM, TEM, EDS, FTIR分析技术对样品结构和组成进行了系统的表征. 结果表明, 得到的产物为TiO₂＠SiO₂亚微米级同轴电缆, 以无定型SiO₂为壳层, 晶态TiO₂为芯层, 电缆平均直径450 nm, 壳层厚度90 nm, 电缆长度＞300 μm, 同时在样品中发现个别纤维呈现管状结构, 对其形成机理进行了讨论.     

十三氟辛基修饰的疏水有机-无机杂化二氧化硅膜孔结构、氢气分离及水热稳定性

采用1,2-双（三乙氧基硅基）乙烷（BTESE）和十三氟辛基三乙氧基硅烷（PFOTES）为前驱体,在酸性条件下通过溶胶-凝胶法制备了十三氟辛基修饰的有机-无机杂化SiO₂膜材料。利用接触角测量、红外光谱、动态光散射和N₂吸附等测试技术分别对膜材料的疏水性、溶胶粒径和孔结构进行表征,并深入研究有支撑膜材料的氢气渗透、分离性能以及长期水热稳定性。结果表明,十三氟辛基修饰后的膜材料由亲水性变成了疏水性,当n_PFOTES/n_BTESE=0.6时膜材料对水的接触角达到（110.4±0.4）°,膜材料还保持微孔结构,孔径分布在0.5~0.8nm。氢气在修饰后的膜材料中的输运遵循微孔扩散机理,在300℃时,氢气的渗透率达到8.5×10^-7mol·m^-2·s^-1·Pa^-1,H₂/CO₂,H₂/CO和H₂/SF₆的理想分离系数分别为5.49,5.90和18.36,均高于相应的Knudsen扩散分离因子。在250℃且水蒸气物质的量分数为5%水热环境下陈化250h,氢气渗透率和H₂/CO₂的理想分离系数基本保持不变,膜材料具有良好的水热稳定性。     

Preparation and characterization of polyvinyl butyral/silica hybrid antireflective coating: effect of PVB on moisture-resistance and hydrophobicity

A new modified antireflective coating was prepared by base catalyzed sol–gel process using tetraethylorthosilicate as precursor and polyvinyl butyral as modifier. The properties of the silica sols and AR coatings were characterized with Fourier-transfer infrared absorption spectroscopy, particle size analyzer, transmission electron microscope, programmable rheometer, UV–Vis spectrophotometry, ellipsometry, atomic force microscope and contact angle measurement. It was found that addition of 4% PVB greatly enhanced moisture-resistance of the AR coating. Optical transmittance of 4% PVB modified AR coating on BK7 substrate was found to be nearly 100%. The water contact angles of normal and 4% PVB modified AR coating were 51 and 53°, respectively, which indicates no significant increase of hydrophobicity of the modified coating. The peak transmittance of 4% PVB modified AR coating was almost unaffected after being exposed to the moist surroundings while that of normal silica coating decreased sharply from 99.8 to 96.5% within 2 weeks. The excellent moisture-resistance of PVB modified AR coating may be attributed to the adsorption of PVB on the surface of AR coating.     

Focus on moisture-resistance and hydrophobicity of SiO<Subscript>2</Subscript> antireflective film improved by poly(isopropylene oxide) glycerolether

The poly(isopropylene oxide) glycerolether (PO) modified silica antireflective (AR) coating films were prepared by sol–gel method. The properties of the silica sols and AR films were characterized by particle size analyzer, transmission electron microscope, UV–Vis spectro-photometry, spectroscopic ellipsometer and contact angle measurement. The results show that PO addition has inconspicuous effect on the transmittance of AR coatings; the maximum transmittance reached 99.5%. Thicknesses of films increase and refractive index decrease with increase of PO concentration. The contact angle with water for the silica films with and without PO was 68.5^o and 28.5^o, respectively, which indicates an increase of hydrophobicity of the modified coating. When the films were placed in 95% relative humidity at room temperature for 30 days, transmittance loss for the unmodified and modified silica films were 2.5 and 0.6% respectively. Moisture-resistance of the film is greatly improved by PO addition.     

New approach to fabricate an extremely super‐amphiphobic surface based on fluorinated silica nanoparticles

Superoleophobic surfaces possessing static contact angles greater than 140° with organic liquids are extremely rare. A simple approach has been developed to fabricate an extremely superamphiphobic coating material based on fluorinated silica nanoparticles resulting contact angles of water and diiodomethane at 167.5° and 158.6°, respectively. The contact angle of diiodomethane at 158.6° is substantially higher than the highest literature reported value we know of at 110°. In addition, this developed film also possesses extremely high contact angles with other organic liquids such as soybean oil (146.6°), decahysronaphthalene (142.5°), diesel fuel (140.4°), and xylene (140.5°). This developed superamphiphobic organic–inorganic hybrid film possesses unique liquid repellency for both water and organic liquids that can be used as functional coatings on numerous substrates by a simple coating process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1984–1990, 2008     

Highly transparent superhydrophobic thin film with low refractive index prepared by one-step coating of modified silica nanoparticles

An easy and effective method to prepare superhydrophobic thin film has been developed. The film with optically transparent and low refractive index was composed by one-step coating with modified silica nanoparticles. The silica nanoparticles were prepared by sol–gel process of hydrolysis and condensation of alkoxysilane compounds and then surface modification silica nanoparticles, 50 ± 10 nm, were accomplished using methoxytrimethylsilane (MOTMS). Water contact angle of film increased with the weight of MOTMS of silica sol. When the weight of MOTMS was optimized, the water contact angle and sliding angle of film were 152.8° and less than 10°, respectively. The transmittance of film was also increased as compared to the un-coated microscope glass slide, from 91 to 93.5 %. The refractive index of the film was approximately 1.09 as measured by ellipsometer. The superhydrphobic thin film was also successfully made by using spray coating and the water contact angle of this film was more than 160°. Surface morphology of difference coating methods, dip and spray, were studied. Our result suggests that the film can be applied for superhydrophobicity and optical applications.     

Fabrication of PZT/CuO composite films and their photovoltaic properties

In this paper, we reported the design and preparation of a double-layer antireflective (AR) coating, which possessed relatively high transmittance at 351, 527, and 1053?nm. The refractive indices and film thicknesses of the under layer and upper layer of the simulated AR coating were determined as 1.27, 95?nm and 1.18, 106?nm, respectively. The under layer of the double-layer coating dip-coated from a mixture of base-catalyzed and acid-catalyzed silica sols had a refractive index of 1.27. The upper layer fabricated by the deposition of methylated silica nanoparticles by simply adding methyltriethoxysilane into the base-catalyzed silica sols possessed a refractive index of 1.18. The hydrophobicity of coatings could be dramatically improved with the water contact angle increasing from 23.4° to 150.0°, and the refractive indices of the pure base-catalyzed silica coatings were easily decreased from 1.20 to 1.12 through the surface treatment of silica nanoparticles. Thus, we have successfully prepared a double-layer AR coating, which had a high transmittance of 99.8%, 96.1%, and 99.7% at 351, 527, and 1053?nm, respectively.

Open image in new window

     

Fabrication and characterization of superhydrophobic silica nanotrees

Superhydrophobic silica nanotrees were obtained by sol–gel method with hybrid silica sol and jelly-like resorcinol formaldehyde resin. Rough surfaces were obtained by removing the organic polymer at high temperature. After the films with rough surface were modified by trimethylchlorosilane (TMCS), the wettability of the film changed from superhydrophilic to superhydrophobic. The surface roughness of the silica nanotrees film is about 20 nm, and it is transparent and superhydrophobic with a water contact angle higher than 150°.     

Polysilazane as the source of silica: the formation of dense silica coatings at room temperature and the new route to organic–inorganic hybrids

Xylene solutions of perhydropolysilazane (PHPS) were used as the coating solutions for preparing silica coatings at room temperature. The PHPS-to-silica conversion was achieved by exposing the spin-on coatings to the vapor from aqueous ammonia. In order to examine the significance of the mechanical properties of the PHPS-derived silica coatings, the pencil hardness was measured, which was compared with that of tetraethoxysilane (TEOS)-derived silica coatings. The pencil hardness was over 9H at a load of 1 kg, which was much higher than that of the TEOS-derived silica gel films, and was comparable to that of the TEOS-derived films heat treated at 300 °C. Second, poly(methyl methacrylate) (PMMA)–silica hybrid coatings were prepared from xylene solutions of PMMA and PHPS via exposure to the vapor from aqueous ammonia. Crack-free, optically transparent PMMA–silica hybrid coatings could be prepared, where PHPS-to-silica conversion was confirmed by infrared absorption spectroscopy. The refractive index was around 1.42–1.50, and the contact angle with water increased from 35 to 70° with increasing PMMA content. The pencil hardness greatly increased during the PHPS-to-silica conversion, and was much higher than that of the non-heat treated TEOS-derived hybrid coatings. The durability in tetrahydrofuran (THF) was also evaluated by measuring the reduction in thickness occurring during soaking in THF. The durability decreased with increasing PMMA content, but was much higher than that of the non-heat treated TEOS-derived hybrid coatings. Both the hardness and the durability were comparable to those of the TEOS-derived coatings heated at 300 °C. The hybrid coatings could also be deposited on poly(ethylene terephthalate) substrates, where no cracks were observed at high PMMA contents even when the substrate was bent.     

聚氧化丙烯醚对SiO2减反膜性质的影响

采用溶胶-凝胶制备的SiO2减反膜具有优良的光学特性和高损伤阈值,可以用做高反膜和减反膜的低折射率匹配层.在高功率激光领域具有十分诱人的应用前景.     

Organic–inorganic hybrid silica film coated for improving resistance to capsicum oil on natural substances through sol–gel route

This study concerns the organic–inorganic hybrid coating of silica sol based on dyed cotton, silk and wool fabrics in order to increase the repellence to capsicum oil via adding methyltriethoxysilane, octyltriethoxysilane, hexadec-ltrimethoxysilane or tridecafluorooctyltriethoxysilane (FAS) in the inorganic silica sol. The dyed cotton fabric treated with hybrid silica sol doped with FAS (F-silica sol, FAS 4 %) presents oil-repellent capability, and the contact angles of capsicum oil on the treated cotton, silk and wool fabrics are 98.5°, 111.59° and 122.15°, respectively. A high FAS concentration (20 %) can improve the oil-repellent ability to 5 grades comparing to the untreated fabrics. The color strengths (K/S) of the coated fabrics change slightly, while the maximum absorption wavelengths of the coated fabrics are the same as the untreated fabrics. Although the drape coefficient of cotton fabric is increased to 54 % from 39 % after coated with F-silica sol, the effect is not significant. Compared to the weight gain rate of untreated cotton, silk and wool samples (1.89, 1.23 and 2.38 %), the weight gain rate of the cotton, silk and wool samples coated with F-silica sol are 6.99, 4.76 and 7.69 %, respectively. The calculated sol–gel weight gains (5.10, 3.53 and 5.31 %) of coated fabrics indicate that the silica coating is subsistent on the fiber surfaces.     

Silica/Silicone Nanofilament Hybrid Coatings with Almost Perfect Superhydrophobicity

A facile method for the preparation of silica/silicone nanofilament hybrid coatings with almost perfect superhydrophobicity (contact angle=179.8° and sliding angle=1.3°) is presented. The coatings are obtained by dip‐coating of silica nanoparticles, followed by chemical vapor deposition of silicone nanofilaments. Predominant growth of silicone nanofilaments onto aggregated silica nanoparticles generates a two‐tier structure. The effect of silica nanoparticle size on the growth of silicone nanofilaments, along with their anti‐wetting properties and transparency are investigated in detail. Surface roughness and anti‐wetting properties can be simply regulated by controlling the size of silica nanoparticles.