抗氧化剂1790合成反应的研究

以6-叔丁基-3-氯甲基-2,4-二甲基苯酚和氰尿酸三钠盐为原料,在N,N-二甲基甲酰胺溶剂中合成1,3,5-三(4-叔丁基-3-羟基-2,6-二甲基苄基)-1,3,5-三嗪-2,4,6-(1H,3H,5H)-三酮(抗氧化剂1790),确定较佳的缩合工艺条件。考察了溶剂种类及用量、物料配比、反应温度及时间对反应收率的影响。实验结果表明:在N,N-二甲基甲酰胺溶剂中,反应温度为110℃,反应时间为2.5 h,n(6-叔丁基-3-氯甲基-2,4-二甲基苯酚)/n(氰尿酸三钠盐)=3.2∶1,产品收率为89%,纯度99%(HPLC面积归一化法)。产品结构经IR、MS和~1H-NMR表征。     

含糖基水溶性紫外吸收剂的合成与表征

以三聚氯氰(TCT)、2,4-二羟基二苯甲酮(UV-0)、双丙酮葡萄糖为原料,经三步反应合成一种具有反应性基团的水溶性紫外吸收剂3-(2-(2-羟基苯基苯甲酮-4-氧基)-4-氯-1,3,5-三嗪-6-氧基)-1,2-异丙叉-α-D-葡萄糖(UV-DTM),产物的结构经IR、NMR和MS表征。探讨了每一步反应的条件对反应产率的影响。合成3-(4,6-二氯-1,3,5-三嗪-2-氧基)-1,2,5,6-双异丙叉-α-D-葡萄糖(DTDT)的优化反应条件为:n(三聚氯氰)∶n(双丙酮葡萄糖)∶n(Na OH)=0.9∶1∶1.7,在丙酮和水的混合体系中0℃下反应8h,产率73%。合成3-(2-(2-羟基苯基苯甲酮-4-氧基)-4-氯-1,3,5-三嗪-6-氧基)-1,2,5,6双异丙叉-α-D-葡萄糖(UV-DT)的优化条件为:n(DTDT)∶n(UV-0)∶n(Na OH)=1∶1.1∶1,在丙酮和水的混合体系中30℃下反应2h,产率74%。合成UV-DTM的优化条件为:每1mmol UV-DT与0.5m L盐酸(36%)在THF体系中25℃下反应5h,产率74%。UV-DTM的紫外吸收性能在240~400 nm内表现良好,水溶性得到大幅改善。     

主链型阳离子表面活性剂聚季铵盐的制备

以N,N-二甲基-1,3-丙二胺、尿素及1,4-二氯丁烷为原料,通过共缩聚反应两步法制备了一种新的主链型的水溶性聚季铵盐.采用正交试验获得了制备聚季铵盐的最佳条件：N,N-二甲基-1,3-丙二胺与尿素的物质的量比为2∶1,反应温度为135℃,反应时间为11h,得到中间体双[3-（N,N-二甲基丙胺基）]丙脲,产率高达99％;中间体与1,4-二氯丁烷的物质的量比为1∶1,于90℃下反应6h.采用红外光谱和核磁氢谱对产物结构进行表征,测定了其热稳定性和特性粘数.     

主链含芳基均三嗪环结构杂萘联苯共聚芳醚腈的结构与性能

以含均三嗪环结构的双氟单体2,4-二(4-氟苯基)-6-苯基-1,3,5-三嗪与商用2,6-二氟苯腈为共聚单体,与具有扭曲、非共平面结构的4-(4-羟基-苯基)-2H-二氮杂萘-1-酮(DHPZ)经溶液亲核取代逐步聚合,合成了一系列主链含三芳基均三嗪环结构和二氮杂萘酮结构线性共聚芳醚腈(PPENPs),其特性黏数为0.65～1.02 dL/g;采用FTIR和1H-NMR证明了聚合物结构与设计一致.PPENPs的DSC曲线中只有一个玻璃化转变温度,在301～ 337℃之间,且随着分子链中三嗪环结构的增加而升高.N2气氛5％热失重温度在510℃以上,800℃残碳率大于60％.当共聚物中三嗪环含量低于50％时,在室温下可溶于N-甲基吡咯烷酮(NMP)、N,N-二甲基乙酰胺(DMAc)和氯仿(CHCl3)等极性非质子溶剂中.其薄膜的拉伸强度为72 ～ 84 MPa,断裂伸长率为7.6％ ～11％,且随着分子链中三嗪环结构的增加而降低.     

吡啶桥联的聚酰亚胺的合成与性能研究

以3,4-二甲基苯乙酮与3,5-双(三氟甲基)苯甲醛为原料,通过Chichibabin反应制备了吡啶桥联的四甲基化合物,该化合物再经氧化、脱水反应制备了主链含有吡啶环、侧链带有双三氟甲基取代苯侧基的新型含氟芳香族二酐单体,2,6双(3′,4′-二羧基苯基)-4-(3″-,5″-双三氟甲基苯基)吡啶二酐(6FDAPA).FT IR、NMR、质谱以及元素分析等测试结果表明,6FDAPA的结构与预期的相符.利用6FDAPA与另外一种不含氟的二酐单体2,6双(3′,4′二羧基苯基)4苯基吡啶二酐(DAPA)分别与含氟二胺单体,1,4双(2三氟甲基4氨基苯氧基)苯(6FAPB)通过两步热亚胺化法制备了两种聚酰亚胺(PI)薄膜.测试结果表明,6FDAPA6FAPB(PI2)与DAPA6FAPB(PI1)相比具有相近的耐热性能,玻璃化转变温度为280℃,起始热分解温度为580℃、700℃时的重量保持率64.5%.同时PI2具有更为优良的透光性,紫外可见光谱(UV Vis)测试表明,PI2与PI1薄膜在450nm处的透光率分别为85.7%与69.4%.     

5,7-二甲氧基-4-甲基苯酞和5,7-二羟基-4-甲基苯酞的新合成方法

以3,5-二甲氧基苯甲醇为起始原料, 经过五步反应, 合成了5,7-二甲氧基-4-甲基苯酞和5,7-二羟基-4-甲基苯酞这两个用于合成霉酚酸的重要中间体, 产率分别达到80%和72%. 6-氯甲基-2,4-二甲氧基苯甲醛经过亚氯酸钠氧化成酸的同时发生内酯化反应生成5,7-二甲氧基苯酞是最关键的一步.     

受阻胺光稳定剂Chimassorb 119的合成

以N-丁基-2,2,6,6-四甲基-4-哌啶胺和2,4,6-三氯-1,3,5-三嗪为起始原料,经取代、甲基化反应后,与N,N′-二-（3-氨丙基）乙二胺进行亲核取代反应合成了受阻胺光稳定剂Chimassorb 119,总收率可达77.1 %,其结构经¹H NMR和ESI-MS确证。     

黑索今的新型合成路线

以乙腈/三聚甲醛为原料合成1,3,5-三乙酰基-均-三嗪（TRAT）,再硝解制备黑索今(RDX)。 聚合反应中,当n(CH3CN)∶n(C3H6O3)=2∶1,n(H2SO4)∶n(C3H6O3)=1∶7.5,反应温度75 ℃,反应3 h时,TRAT的产率为95.2%。 硝解反应中,当n(N2O5)∶n(TRAT)=7∶1,n(HNO3)∶n(N2O5)=6∶1,反应温度45 ℃,反应1 h时,RDX的产率为87.2%。 RDX的全程产率为83.0%。 该工艺简单、易于控制,废酸污染小,有望应用于工业化生产。     

N-甲基-2-(3,4-二羟基苯基)[60]富勒烯吡咯烷衍生物的合成

在N2气保护下,由1,3-偶极环加成反应合成了含2个羟基的C60吡咯烷衍生物:N-甲基-2-(3,4-二羟基苯基)[60]富勒烯吡咯烷. 用UV-Vis、FT-IR、1H NMR、MS等测试技术表征了产物的结构,通过单因素方法,探讨了反应条件对产物产率的影响. 最佳反应条件为:n(C60)∶ n(N-甲基甘氨酸)∶ n(3,4-二羟基苯甲醛)=1∶ 2∶ 5,温度为95 ℃,反应时间为28 h,产率可达66%(以消耗的C60计).     

含氟苯并异噁唑衍生物的合成及活性研究

以2,4-二甲氧基苯胺为起始原料,通过乙酰化保护合成N-(2,4-二甲氧基苯基)乙酰胺(2),经傅克反应合成N-(4-羟基-2-甲氧基-5-丙酰基苯基)乙酰胺(3),3再与盐酸羟胺反应生成N-(4-羟基-5-(1-(羟基亚氨基)丙基)-2-甲氧基苯基)乙酰胺(4),4在DMF-DMA作用下生成N-(3-乙基-6-甲氧基...     

The Oxidation of Hexahydrotriazines

Summary. N-Alkyl-2,4-dioxohexahydro-1,3,5-triazines oxidize readily with oxygen to the corresponding cyanuric acid derivates. The oxidation of 1,3,5-trimethyl-2,4-dioxohexahydro-1,3,5-triazine resulted in a stable form of hydroperoxide. During the oxidation of 1,3,5-trimethyl- 6-phenyl-2,4-dioxohexahydro-1,3,5-triazine this hydroperoxide could not be identified, however, the result was the stable reaction product bis-[6-phenyl-1,3,5-trimethyl-2,4-dioxohexahydro-1,3,5-triazin]peroxide.     

Synthesis of Aromatic Polythioethers Containing 1,3,5-Triazine Ring by Aromatic Nucleophilic Substitution Polymerization

Abstract

Reaction of 2,4-dichloro-6-phenyl-1,3,5-triazines with bis(4-mercaptophenyl) sulfide in the presence of a base in THF afforded the corresponding condensation polymer as a whole aromatic polythioether in moderate yield. The polymerization of several 2,4-dichloro-1,3,5-triazine derivatives with this dithiols also proceeded in the o-dichlorobenzene-water two-phase system by using phase transfer catalysts. The resulting polymers consisted of THF-soluble and -insoluble fractions. The x-ray diffraction pattern indicated that these THF-insoluble polymers have a highly crystalline nature. Further, the polymers obtained here showed high thermal stability.     

聚-1,3,5-三嗪的合成及性能

将联苯二脒与苯甲醛或其盐酸盐与乙酸酐进行缩聚反应,合成了两种新的聚-1,3,5-三嗪,用元素分析、红外光谱、差热分析及热重分析进行了表征,聚合物的η_(比粘)为0.46—0.56分升/克(1％硫酸,25℃),具有良好的耐温性和耐水解性,也有一定的溶解性,利用这种聚-1,3,5-三嗪和二氯化钯反应,可以制成新的高分子络合物。     

SYNTHESIS AND PROPERTIES OF POLY-1,3,5-TRIAZINES

Two new polytriazines: poly[2-methyl-4, 6-(4,′4″-diphenylene)-1, 3, 5-triazine] (Ⅰ) and poly[2-phenyl-4, 6-(4′, 4″-diphenylene)-1, 3, 5-triazine] (Ⅱ) were synthesized from the solution condensation of biphenyl-4, 4′-diamidine dihydrochloride with acetic anhydride and biphenyl-4, 4′-diamidine with benzaldehyde respectively. These two polymers were characterized by TGA, DTA, elemental analysis and IR spectroscopy. They exhibited good thermal oxidative stability as shown by the fact that the powders of these polymers suffered 5.4%, 2.4% weight loss after isothermal aging in air at 300℃for 200 hours. The decomposition temperature of (Ⅱ) was 583℃in air and 590℃in N_2. These linear poly-1, 3, 5-triazines were soluble in concentrated sulfuric acid, phosphoric acid and trifluoroacetic acid whereas the erosslinked poly-1, 3, 5-triazines reported in the literature were insoluble and infusible.It is interesting that these polymers can form complexes with metal halides as determined by X-ray photoelectron spectroscopy (XPS). The polymer metal complex (Ⅲ). PdCl_2 possesses catalytic activity for hydrogenation.     

Aromatic Nucleophilic Substitution Polymerization of Dichloro-1,3,5-Triazines with Alkanedithiols

Reaction of 2,4-dichloro-6-phenyl-1,3,5-triazine with alkane-dithiols in the presence of a base in THF afforded the corresponding condensation polymers containing triazinylthio group in moderate yields. This polymerization reaction also proceeded in the o-dichlorobenzene-water two-phase system by using phase transfer catalysts. The resulting polymers consisted of THF-soluble and insoluble fractions. When the reaction was carried out at a higher temperature or for a longer reaction time, the yield of the insoluble polymer was increased. The THF-soluble polymers were also soluble in toluene, and they had the ability to extract sodium and potassium ions from aqueous picrates. The polymers functioned as catalysts for substitution reactions of an alkyl bromide and the reduction of a ketone with sodium borohydride under liquid-liquid phase transfer conditions with a reactivity superior to that of the monomeric analog.     

Azines and Their Acyclic Derivatives as Transferers of One-carbon Fragment in Reactions with Pyrazolones

Enehydrazine derivatives have been obtained by the reaction of 6-phenyl-1,2,4-triazine 4-oxide with pyrazolones 2, which on further heating with pyrazolones 2 are converted into the corresponding symmetrical or unsymmetrical derivatives of dipyrazolylmethane. Enehydrazine derivatives of 1,3-dimethyl-5-nitrosouracil and 1,3-dimethylimidazolidine interact with 3-methyl-1-phenyl-5-pyrazolone (2a) with the formation of dipyrazolylmethane derivative. On interacting compound 2a or 3-methyl-1-(p-nitrophenyl)-5-pyrazolone with 3,6-diphenyl-1,2,4-triazine 4-oxide 12 the corresponding 4,4'-bispyrazolones are formed, but the interaction of compound 12 with 3-(p-nitrophenyl)-1-phenyl-5-pyrazolone leads to dipyrazolylmethane derivative. Dipyrazolylmethane derivative is obtained on heating of fervenulin 4-oxide, 2,4-dihydroxy-5-nitropyrimidine, and 1,3,5-triazines: 6-azauracil, 5-azauracil, azacytosine, and 2,4-diamino-s-triazine with pyrazolone 2a.     

新型钴酞菁接枝温敏聚合物的制备及性能

采用2,4,6-三氯-1,3,5-三嗪对四氨基钴酞菁进行改性,并以共价键接枝到聚N-异丙基丙烯酰胺上制得一种新型温敏性高分子催化剂——钴酞菁接枝温敏聚合物,并采用UV-Vis、TG等对其进行表征.对钴酞菁接枝温敏聚合物、温敏聚合物和小分子金属酞菁进行溶解性测试,结果表明与四氨基钴酞菁相比,所合成的钴酞菁接枝温敏聚合物能溶解于水和大多数有机溶剂,且该聚合物水溶液具有良好的温敏性,其最低临界溶解温度(LCST)为34.5℃.采用浊度法考察了不同比例的混合溶剂(乙醇/水、DMF/水)对LCST的影响,结果表明随着有机溶剂含量的增加,LCST先下降后升高,而当有机溶剂增加到一定程度时温敏性消失.本文还考察了钴酞菁接枝温敏聚合物对2-巯基乙醇的催化活性,结果表明随着温度升高,催化活性也不断提高,而当温度超过LCST时催化活性急剧下降,聚合物从溶液中析出.基于这些特性,该温敏聚合物负载酞菁作为一种新型的催化剂可实现均相催化、异相分离.     

聚苯基-1,3,5-三嗪的高温水解研究

对聚苯基-1,3,5-三嗪及其模型化合物在250℃/3.97MPa高温水中的水解行为进行了研究。聚苯基-1,3,5-三嗪的红外谱图在水解过程中基本保持不变,表明它是一种耐高温水解性能优良的高分子。高效液相色谱、高效毛细管泳色谱及液质联用分析表明,聚合物及其模型化合物的主要水解产物是由对称三嗪杂环被水解而生成的芳香酸,由些提出了它们的水解历程。通过对水解速控步骤活化能的量子化学计算,从理论上解释了这种高分子优良和耐高温水解特性。     

Poly[2,4-bis(chloroamino)-6-vinyl-1,3,5-triazine] as a recyclable oxidizing agent of alcohols

A polymer containing dichlorotriazine moiety was prepared readily by the reaction of poly(2,4-diamino-6-vinyl-1,3,5-triazine) with tert-butyl hypochlorite. This polymer oxidizes various primary and secondary alcohols to the corresponding carbonyl compounds under mild conditions, while the reaction of the monomeric analogue N,N′-dichloroacetoguanamine with alcohols does not proceed. The polymer reagent can be handled easily and recycled for further use.     

Synthesis and structure of 6-azido-2,4-bis(2,2,2-trinitroethylamino)-1,3,5-triazine and its <Emphasis Type="Italic">N</Emphasis>-nitro derivatives

Methods were developed for the synthesis of 6-azido-2,4-bis(2,2,2-trinitroethylamino)- 1,3,5-triazine and its N-nitro derivatives (6-azido-2,4-bis(2,2,2-trinitroethyl)nitramino-1,3,5-triazine and 6-azido-2-(2,2,2-trinitroethylamino)-4-(2,2,2-trinitroethyl)nitramino-1,3,5-triazine) containing combinations of azido, trinitroethyl, and nitramine groups. These compounds are of interest as components of energetic composites. The molecular and crystal structures of 6-azido-2,4-bis(2,2,2-trinitroethylamino)-1,3,5-triazine and 6-azido-2,4-bis(2,2,2-trinitroethyl) nitramino-1,3,5-triazine were studied by X-ray diffraction and NMR spectroscopy.