Dimensional and elemental characterization of suspended particulate matter in natural waters: quantitative aspects in the integrated ultrafiltration, splitt-flow thin cell and inductively coupled plasma–atomic emission spectrometry approach

The present study investigates the quantitative aspects of an analytical procedure for the trace element characterization of suspended particulate matter (SPM) in natural waters. The procedure consists of the following steps: (1) ultrafiltration (UF) concentration; (2) splitt-flow thin (SPLITT) cell fractionation (SF) into different micronic–submicronic dimensional ranges; and (3) inductively coupled plasma–atomic emission spectrometry (ICP–AES) elemental determination on both the separated fractions and the bulk phase. One specific feature of the UF/SF steps is that they are gentle and thus preserve the complexity of the colloidal features of SPM samples as far as possible. The investigation was performed on a real SPM sample (Po River, Italy). Two SF modes were considered: the so called conventional SPLITT fractionation (CSF) mode and the full feed depletion SPLITT fractionation (FFDSF) mode. These differ in terms of resolution, time (both better in CSF as compared to FFDSF) and operating mode (FFDSF does not require a diluting carrier). Quantitative aspects of the UF step recovery and of the CSF and FFDSF modes were investigated in terms of total mass balance proving that only the FFDSF mode is currently satisfactory for quantitative purposes. Mass balance versus the following elements: Cd, Cr, Cu, Mn, Ni and Pb, was performed using ICP–AES over the 0.2–1.5 and 1.5–20 μm FFDSF SPM fractions, proving that the analytical procedure based on UF/FFDSF/ICP–AES is consistent and useful in the investigation of trace element distribution in different SPM dimensional ranges versus that of the bulk phase. The relevance of aggregation–solubility equilibria concerning colloids of SPM phase is emphasized and further improvement of the procedure is discussed.     

Direct determination of toxic trace metals in honey and sugars using inductively coupled plasma atomic emission spectrometry

A rapid method for the determination of Pb, Cd, Cu, Cr, Co, Ni, Mn and Zn in honey and sugars without prior digestion or ashing of the sample was developed, using inductively coupled plasma atomic emission spectrometry (ICP-AES). The critical instrumental parameters such as sample flow rate and radio frequency incident power were thoroughly optimized. The effect of matrix type and its concentration was also examined for glucose/fructose, sucrose and honey matrices. The sensitivity was investigated using calibration curves obtained in presence of the above matrices. The obtained recoveries for Cd, Cu, Cr, Co, Ni and Mn at the μg l⁻¹ level were satisfactory and practically independent of the matrix used for the calibration standards. The recoveries of Pb and Zn were less sufficient. Various commercial samples of honey, sugar, glucose and fructose were analyzed with respect to their toxic metal content. The method can be applied for routine analysis, quality and environmental pollution control purposes at the μg l⁻¹ level of concentration, after suitable dilution of the samples.     

Determination of water soluble trace metals in airborne particulate matter using a dynamic extraction procedure with on-line inductively coupled plasma optical emission spectrometric detection

A novel continuous-flow system for the dynamic extraction of water soluble metal fractions in airborne particulate matter (APM) with subsequent inductively coupled plasma optical emission spectrometric (ICP-OES) analysis of derived extracts is presented. The fully automated extraction system with on-line multi-element detection offers enhanced sensitivity when compared to batch-wise counterparts; additionally it provides information about the extraction process. With the developed procedure detection limits in the order of 1.5 (Ba) to 8.0 (Ni) ng extractable mass per investigated sample could be achieved, which translates to method detection limits for soluble metal concentrations in APM ranging from 0.2 ng m⁻³ (Ba) to 0.9 ng m⁻³ (Fe). Reproducibility of analysis was determined by replicate measurement (n = 6) of an APM sample with an aerodynamic diameter ≤10 μm (PM10), derived results varied between 3.5% (Mn) and 12.1% (Ni) relative standard deviation. Method validation was accomplished by comparison of extracted soluble and remaining non-soluble fractions with the total metal contents of the investigated PM10 samples, showing an excellent mass balance for all elements. Application of the developed procedure for the analysis of water soluble metal fractions in PM10 samples (n = 16) from Linz (Austria) indicated a high variability of extractable fractions ranging from 11.7 ± 7.2% (Fe) to 48.8 ± 15.4% (Mn) of the total metal contents.     

Micro-column preconcentration/separation using thiacalix[4]arene tetracarboxylate derivative modified mesoporous TiO2 as packing materials on-line coupled to inductively coupled plasma optical emission spectrometry for the determination of trace heavy metals in environmental water samples

A novel adsorbent of thiacalix[4]arene tetracarboxylate derivative modified mesoporous TiO₂ was prepared and was used as a packing material for flow injection (FI) micro-column (20 mm × 4.0 mm i.d.) separation/preconcentration on-line coupled to inductively coupled plasma optical emission spectrometry (ICP-OES) simultaneous determination of trace metals (V, Cu, Pb, Cr) in environmental water samples. The experimental conditions for modified mesoporous TiO₂ packed micro-column separation/preconcentration of the target metals were optimized and the interference of commonly coexisting ions was examined. The adsorption capacities of thiacalix[4]arene tetracarboxylate derivative modified mesoporous TiO₂ for V, Cu, Pb and Cr were found to be 14.0, 11.7, 17.7 and 14.5 mg g^− 1, respectively. The detection limits of the method were 0.09, 0.23, 0.50 and 0.15 µg L^− 1 for V, Cu, Pb and Cr, respectively, with a preconcentration factor of 20. The precision of this method were 1.7% (V), 3.9% (Cu), 4.6% (Pb) and 2.9% (Cr) (n = 7, C = 5 µg L^− 1), respectively. The developed method was applied to the determination of trace heavy metals in real samples and the recoveries for spiked samples were found to be in the range of 88.7-107.1%. For validation, a certified reference material of GSBZ50009-88 environmental water sample was analyzed and the determined values were in good agreement with the certified values.