Synthesis and Properties of Phosphorus-Containing Aromatic Polyethers

The phosphorus-containing aromatic polyethers were prepared from bis(p-chlorophenyl)phenylphosphine oxide (BCPO) with the sodium salt of several bisphenols by high temperature solution polycondensation. The best result (yield 84%, n _sp /c = 0.15) was obtained from BCPO with bisphenol A (BPA) in dimethyl sulfoxide. However, the polymerization in the solvents such as N, N′-dimethyl-2-pyrrolidone, hexamethylphosphoramide, and N,N′-dimethylformamide, and the polymerization with the other bisphenols HO-C₆H₄-X-C₆H₄?OH, where X = CO, S0₂, CH₃P(O), C₆H₅P(O) in place of BPA gave gumlike polymers. The polymer prepared from BCPO and BPA did not decompose up to ca. 300°C under air or nitrogen atmosphere, but it decomposed slowly at 300–520°C, and decomposed rapidly at 520–540°C. The activation energy (δE) for the maximum rate of weight loss was 47.8 kcal/mole.     

On the solution characterization of an all-aromatic liquid-crystalline copolyester

Solution characterization of the thermotropic liquid–crystalline copolyester synthesized from terephthalic acid, phenyl hydroquinone, and (1-phenylethyl) hydroquinone (2 : 1 : 1) has been performed. Viscometry, size exclusion chromatography, and light scattering have been carried out under the optimal conditions found for measurement: 85°C in a 50/50 mixture by weight of phenol/1,2,4-trichlorobenzene. The absolute weight-average molecular weight from light-scattering measurements served for calibration of indirect methods of charac-terization (e.g., the limiting viscosity number [η] is related to the molecular weight by [η] = 5.10 × 10^?4 M_w^0.72), and the molecular weight per unit chain length, $ \bar M_L * $, from light scattering and size exclusion chromatography (SEC) is found to be 28 Å^?1, consistent with theoretical expectations. The calculated persistence length q is 28 Å. Moreover, the meth-odology of SEC characterization enables the kinetics of solid-state postpolymerization of this liquid-crystalline copolyester to be studied. © 1993 John Wiley & Sons, Inc.     

Anionic bulk oligomerization of ethylene and propylene carbonate initiated by bisphenol‐A/base systems

When the bulk oligomerization of 1,3‐dioxolan‐2‐one (ethylene carbonate, EC) and 4‐methyl‐1,3‐dioxolan‐2‐one (propylene carbonate, PC) with the 2,2‐bis(4‐hydroxyphenyl)propane (bisphenol‐A, BPA)/base system (bases such as KHCO₃, K₂CO₃, KOH, Li₂CO₃, and t‐BuOK) was investigated at elevated temperature, significant differences were observed. Oligomerization of EC initiated by BPA/base readily takes place, but the oligomerization of PC is inhibited. The very first propylene carbonate/propylene oxide unit readily forms a phenolic ether bond with the functional groups of BPA phenolate, but the addition of the second monomer unit is rather slow. The oligomerization of EC yields symmetrical oligo(ethylene oxide) side chains. According to IR studies the oligomeric chains formed from PC with BPA contain not only ether but also carbonate bonds. The in situ step oligomerization of the BPA dipropoxylate was also identified by SEC, and a possible reaction mechanism is proposed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 545–550, 1999     

UO2, NpO2 and PuO2 preparation in aqueous nitrate solutions in the presence of hydrazine hydrate

It was established that heating to 90 °C of nitrate solutions of U, Np and Pu in the presence of hydrazine hydrate results in the formation of hydrated dioxides of these elements. On ignition under inert or reducing conditions in the temperature range of 280–800 °C hydrated uranium dioxide transmogrify into crystalline UO₂. On ignition in air atmosphere UO₂·nH₂O turns into UO₃ at 440 °C and into U₃O₈ at 570–800 °C. It was shown that thermolysis of the solution containing a mixture of uranium, neptunium and plutonium nitrates at 90 °C in the presence of hydrazine hydrate allows one to prepare hydrated dioxides (U, Np, Pu)O₂·nH₂O which on heating to ~300 °C transmogrify into crystalline product of UO₂, NpO₂ and PuO₂ solid solution. The technique of preparation of solid solutions of U and Pu dioxides is very promising as simple and effective method of production of MOX-fuel for.     

Synthesis and characterization of poly(butylene terephthalates) modified by hydroquinone bis(2-hydroxyethyl)ether

A series of thermoplastic poly(butylene-co-hydroquinone bis(2-hydroxyethyl)ether terephthalates) (PBHT), with different molar ratios of hydroquinone bis(2-hydroxyethyl)ether (HQEE)/1,4-butanediol 9/91, 18/82 and 27/73, were synthesized via melt polycondensation. The compositions, thermodynamics and crystallization properties of the obtained copolyesters were characterized in detail by ¹H NMR, differential scanning calorimeters (DSC), thermogravimetric analysis (TGA) and X-ray diffraction (XRD). These results showed that the PBHTs were successfully synthesized, and the incorporation of the HQEE group significantly improved thermal properties of the polymers. However, HQEE did not change the crystal structure of PBT. The T_m values of the copolymers decreased (from 208?°C to 174?°C) with increasing content of HQEE segments, on the contrary, T_g values increased (from 37?°C to 43?°C). The temperatures for 5% weight loss did not decrease and appeared at a range of 373–377?°C.     

Preparation and photocatalytic activity of fluoroalkyl end-capped vinyltrimethoxysilane oligomer/anatase titanium oxide nanocomposite-encapsulated low molecular weight aromatic compounds

Fluoroalkyl end-capped vinyltrimethoxysilane oligomer/anatase titanium oxide nanocomposite-encapsulated low molecular weight aromatic compounds [R_F-(VM-SiO₂)_n-R_F/an-TiO₂/Ar-H] were prepared by the sol–gel reactions of the corresponding oligomer in the presence of anatase titanium oxide nanoparticles (an-TiO₂) and the aromatic compounds such as bisphenol A [BPA], 1,1′-bi(2-naphthol) [BINOL], and fullerene under alkaline conditions. Thermogravimetric analyses measurements show that R_F-(VM-SiO₂)_n-R_F/an-TiO₂ nanocomposite-encapsulated BPA and BINOL, in which the theoretical contents in the composites are 25?～?32 %, were found to give no weight loss corresponding to the contents of these aromatic compounds even after calcination at 800 °C. On the other hand, the corresponding nanocomposite-encapsulated fullerene exhibited weight loss behavior related to the presence of fullerene under similar conditions; however, UV–vis spectra showed the presence of the residual fullerene in the composites even after calcination. An-TiO₂ in these fluorinated nanocomposites can keep its crystalline structure without phase transformation into rutile even after calcination at 1,000 °C, although the parent an-TiO₂ nanoparticles underwent a complete phase transformation into rutile under similar conditions. Notably, R_F-(VM-SiO₂)_n-R_F/an-TiO₂/Ar-H nanocomposites can give a good photocatalytic activity even after calcination at 1,000 °C for the decolorization of methylene blue under UV light irradiation. More interestingly, these fluorinated nanocomposites before and after calcination were found to exhibit a higher photocatalytic activity at the initial UV light irradiation from 1 to 3 min than that of the corresponding R_F-(VM-SiO₂)_n-R_F/an-TiO₂ nanocomposites under similar conditions.

Rotor-synchronized two-dimensional 13C CP/MAS NMR studies of the orientational order of polymers. I. High-performance ultrahigh molecular weight polyethylene fibers

The orientational order of three morphological components, identified previously as two crystalline components, C₁ and C₂, and an amorphous component, A of four polyethylene fibers, including two gelspun ultrahigh molecular weight (PE-I and PE-II) and two meltspun moderate molecular weight (PE-D and PE) polyethylene fibers are further analyzed by rotor-synchronized two-dimensional ¹³C CP/MAS (ROSMAS) nuclear magnetic resonance (NMR) techniques. Our results indicate that the orientational order of these components differ substantially among themselves in a given fiber and among different fibers of the same component. Values of β_1/2, the polar angle at which the orientational distribution function (ODF) P 〈β〉 decays to half its maximum, are determined to be: 18° (C2 of PE-II), 21° (C2 of PE-I), 29° (C2 of PE-D), 31° (C1 of PE-I) and 50° (C2 of PE). No orientational sideband can be detected for component A, suggesting that the A component is due to the amorphous domain. The implication of this results and the technical limit of this technique are analyzed. © 1993 John Wiley & Sons, Inc.     

Amine-quinone polyurethanes. I. Preparation of polyurethane block copolymers containing 2,5–bis(N-2-hydroxyethyl-N-methylamino)-1,4–benzoquinone diol monomer

The amine-quinone monomer, 2,5–bis(N-2-hydroxyethyl-N-methylamino)-1,4-benzoqui-none (AQM-1), was prepared by the multiple-step condensation of 2-(N-methylam-ino)ethanol with benzoquinone in the presence of oxygen. This crystalline monomer was used to prepare a series of amine-quinone polyurethanes by condensation polymerization, either in the melt or in solution (THF or DMF), with a diisocyanate (MDI, TDI, or IPDI) and an oligomeric diol [poly(caprolactone) or poly(1,2-butylene glycol)]. The amine-quinone functional group was stable under the polymerization conditions, and was incorporated into the main chain, giving red-brown polyurethanes that had molecular weights in the range of 11,000–90,000 and were soluble in THF, MEK, DMF, and DMSO. The thermal properties were consistent with a two-phase morphology with an amorphous soft segment, containing the oligomeric diol, and a microcrystalline hard segment, containing AQM-1. The polymers having a low hard segment content (<50%) were rubbery (soft segment T_g <?25°C); polymers having a high hard segment content (>50%) were thermoplastic (hard segment T_g>150°C). © 1995 John Wiley & Sons, Inc.     

Dielectric studies of tetraaryl and triaryl polycarbonates and comparisons with bisphenol A‐polycarbonate

The relative permittivity, loss, and breakdown strength are reported for a commercial sample of bisphenol A‐polycarbonate (comm‐BPA‐PC) and a purified sample of the same polymer (rp‐BPA‐PC) as well as for two new polycarbonates having low molecular cross‐sectional areas, namely a copolymer of tetraaryl polycarbonate and BPA‐PC (TABPA‐BPA‐PC) and a triaryl polycarbonate homopolymer (TriBPA‐PC). The glass transition temperatures of the new polymers are higher than the T_g of BPA‐PC (187 and 191 °C vs. 148 °C). Relative permittivity and loss measurements were carried out from 10 to 10⁵ Hz over a wide temperature range, and results for the α‐ and γ‐relaxation regions are discussed in detail. For the α‐relaxation, the isochronal peak position, T_α, scales approximately with T_g. On the other hand, the peak temperature for the γ‐relaxation is approximately constant, independent of T_g. Also, in contrast to what is observed for α, γ exhibits a strong increase in peak height as temperature/frequency increases and a significant difference is found between Arrhenius plots determined from isochronal and isothermal data analyses. Next, the γ‐relaxation region for comm‐BPA‐PC and associated activation parameters show strong history/purity effects. The activation parameters also depend on the method of data analysis. The results shed light on discrepancies that exist in the literature for BPA‐PC. The shapes of the γ loss peaks and hence glassy‐state motions for all the polymers are very similar. However, the intensities of the TriBPA‐PC and TABPA‐BPA‐PC γ peaks are reduced by an amount that closely matches the reduced volume fraction of carbonate units in the two new polymers. Finally, for comm‐BPA‐PC, the breakdown strength is strongly affected by sample history and this is assumed to be related to volatile components in the material. It is found that the breakdown strengths for TriBPA‐PC and TABPA‐BPA‐PC are relatively close to that for rp‐BPA‐PC with the value for TriBPA‐PC being slightly larger than that for rp‐BPA‐PC or the value usually reported for typical capacitor grade polycarbonate. Finally, it is shown that the real part of the relative permittivity remains relatively constant from low temperatures to T_g. Consequently, based on the dielectric properties, TriBPA‐PC and TABPA‐BPA‐PC should be usable in capacitors to at least 50 °C higher than BPA‐PC. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Orientation of uniaxially stretched poly(ethylene naphthalene 2,6‐dicarboxylate) films by polarized infrared spectroscopy

Poly(ethylene naphthalene‐2,6‐dicarboxylate) has been uniaxially stretched at different draw ratios and at two different temperatures below and above its glass transition (T_g ～ 120 °C) respectively, at 100 and 160 °C. Crystallinity has been evaluated from calorimetric analyses and compared to the values deduced by FTIR spectroscopic data. As expected, the obtained results are quite similar and show that films stretched at lower temperature (100 °C) are more crystalline than those stretched at 160 °C. Optical anisotropy associated with orientation has been evaluated by birefringence and show that films stretched at 100 °C are more birefringent than those stretched at 160 °C as a result of a higher chain relaxation above T_g. Polarized FTIR was also performed to evaluate the individual orientation of amorphous and crystalline phases by calculating dichroic ratios R and orientation functions 〈P₂(cos θ)〉 and also show that amorphous and crystalline phases are more oriented in the case of films stretched below T_g. Nevertheless, the orientation of the amorphous phase is always weaker than that of the crystalline phase. Films stretched at 100 °C show a rapid increase in orientation (and crystallinity) with draw ratio and 〈P₂(cos θ)〉 reaches a limit value when draw ratio becomes higher than 3.5. Films drawn at 160 °C are less oriented and their orientation is increasing progressively with draw ratio without showing a plateau. A careful measurement of the IR absorbance was necessary to evaluate the structural angles of the transition moments to the molecular chain axis. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1950–1958, 2007     

Syntheses and gas transport properties of polyarylates based on isophthalic and terephthalic acids and mixtures of bisphenol A and 1, 1 bi‐2‐naphthol

Polyarylates based on isophthalic (IA) and terephthalic (TA) acids and an equimolar mixture of the diols Bisphenol A (BPA) and 1,1 bi‐2‐naphthol (BN) were synthesized to produce BPA‐BN/IA and BPA‐BN/TA polymers and to measure their gas permeability coefficients, P(i), at several pressures and 35 °C, to the gases O₂, N₂, CH₄, and CO₂. For the BPA‐BN/IA membranes, at a 2 atm up‐stream pressure, the P(O₂) and P(CO₂) are 0.93 and 4.0 Barrers with O₂/N₂ and CO₂/CH₄ ideal separation factors of 6.7 and 27. For the BPA‐BN/TA, at a 2 atm up‐stream pressure, the P(O₂) and P(CO₂) are 2.0 and 9.9 Barrers with O₂/N₂ and CO₂/CH₄ ideal separation factors of 5.6 and 21. Comparing the selectivity–permeability balance of properties shown by the BPA/TA membranes with that shown by the copolymer BPA‐BN/TA, the balance moves in the direction of higher selectivity and lower permeability because of the incorporation of BN, which is a more rigid monomer than BPA. However, when the balance of properties for the pair O₂/N₂ shown by BPA‐BN/TA is compared with the one shown by other membranes such as those based on mixtures of diols and diacids, that is the bisphenol A‐naphthalene/I‐T polymers reported in the literature, the balance moves up and to the right of the typical selectivity–permeability trade‐off observed in the BPA‐polyarylate family. Thus, simultaneous incorporations of flexible and rigid monomers in both the diols and the diacids lead to more productive and more selective membranes. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 256–263, 2006     

Co60 γ-radiation-induced copolymerization of ethylene and carbon monoxide

The γ-radiation-induced free-radical copolymerization of ethylene and CO has been investigated over a wide range of pressure, initial gas composition, radiation intensity, and temperature. At 20°C., concentrations of CO up to 1% retard the polymerization of ethylene. Above this concentration the rate reaches a maximum between 27.5 and 39.2% CO and then decreases. The copolymer composition increases only from 40 to 50% CO when the gas mixture is varied from 5 to 90% CO. A relatively constant reactivity ratio is obtained at 20°C., indicating that CO adds 23.6 times as fast as an ethylene monomer to an ethylene free-radical chain end. For a 50% CO gas mixture, the above value of 23.6 and the copolymerization rate decrease with increasing temperature to 200°C. The kinetic data indicate a temperature-dependent depropagation reaction. Infrared examination of copolymers indicates a polyketone structure containing ? CH₂? CH₂? and ? CO? units. The crystalline melting point increases rapidly from 111 to 242°C., as the CO concentration in the copolymer increases from 27 to 50%. Molecular weight of copolymer formed at 20°C. increased with increasing CO, indicating M?_n values >20,000. Increasing reaction temperature results in decreasing molecular weight. Onset of decomposition for a 50% CO copolymer was measured at ≈250°C.     

Morphology and crystal structure of the poly(ethylene oxide)–hydroquinone molecular complex

The occurrence of a molecular complex between poly(ethylene oxide) (PEO) and p‐dihydroxybenzene (hydroquinone) has been determined using different experimental techniques such as differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD), and Fourier transform infrared spectroscopy (FTIR). From DSC investigations, an ethylene oxide/hydroquinone molar ratio of 2/1 was deduced. During the heating, the molecular complex undergoes a peritectic reaction and spontaneously transforms into a liquid phase and crystalline hydroquinone (incongruent melting). A triclinic unit cell (a = 1.17 nm, b = 1.20 nm, c = 1.06 nm, α = 78°, β = 64°, γ = 115°), containing eight ethylene oxide (EO) monomers and four hydroquinone molecules, has been determined from the analysis of the X‐ray diffraction fiber patterns of stretched and spherulitic films. The PEO chains adopt a helical conformation with four monomers per turn, which is very similar to the 7₂ helix of the pure polymer. A crystal structure is proposed on the basis of molecular packing considerations and X‐ray diffraction intensities. It consists of a layered structure with an alternation of PEO and small molecules layers, both layers being stabilized by an array of hydrogen bonds. The morphology of PEO–HYD crystals was studied by small angle X‐ray scattering and DSC. As previously shown for the PEO–resorcinol complex, PEO–HYD samples crystallize with a lamellar thickness corresponding to fully extended or integral folded chains. The relative proportion of lamellae with different thicknesses depends on the crystallization temperature and time. Finally, the observed morphologies are discussed in terms of intermolecular interactions and chain mobility. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1197–1208, 1999     

Dyed polyvinyl chloride films for use as high-dose routine dosimeters in radiation processing

Characteristics of the polyvinyl chloride (PVC) films containing 0.11 wt% of malachite green oxalate or 6GX-setoglausine and about 100 μm in thickness were studied for use as routine dosimeters in radiation processing. These films show basically color bleaching under irradiation with ⁶⁰Co γ-rays in a dose range of 5–50 kGy. The sensitivity of the dosimeters and the linearity of dose-response curves are improved by adding 2.5% of chloral hydrate [CCl₃CH(OH)₂] and 0.15% hydroquinone [HOC₆H₄OH]. These additions extend the minimum dose limit to 1 kGy covering dosimetry requirements of the quality assurance in radiation processing of food and healthcare products. The dose responses of both dyed PVC films at irradiation temperatures from 20°C to 35°C are constant relative to those at 25°C, and the temperature coefficients for irradiation temperatures from 35°C to 55°C were estimated to be (0.43±0.01)%/°C. The dosimeter characteristics are stable within 1% at 25°C before and 60 days after the end of irradiation.     

Polymerization of styrene by poly(bisphenol a 4,4′-azobis-4-cyanopentanoate)

A free radical initiator, poly(bisphenol A 4,4′-azobis-4-cyanopentanoate) (BPA), containing more than one azo group per molecule, was used to polymerize styrene in N,N-dimethylformamide (DMF) at 60°C. Polymerization rates were measured gravimetrically or dilatometrically, and the molecular weights of the isolated polystyrenes were determined viscometrically, both before and after hydrolysis. BPA has a relatively low initiator efficiency of 0.28. The activation energy and velocity constant at 60°C for decomposition of BPA per azo group in DMF were found spectroscopically to be 105.9 kJ/mole and 2.08 × 10^?5 sec^?1, respectively. The molecular weights of unhydrolysed polystyrenes increased with increasing conversion and a theory is developed to explain these results.     

Syntheses and permselectivity properties of polysulfones based on bisphenol A and 1, 1 bi‐2 naphthol

Polysulfone copolymers based on mixtures of bisphenol A, BPA, and 1,1 bi‐2 naphthol, BN, diols have been synthesized and their gas permeability coefficients and selectivity separation factors for O₂/N₂ and CO₂/CH₄, at 5 atm and 35 °C, have been measured in a standard permeation cell. The polysulfone copolymers can form flexible thin films suitable for gas separation membranes. The gas selectivity for O₂/N₂ measured for the polysulfone copolymers synthesized with 50 and 70 mol % of BN, with the rest being BPA, in the initial mixture of diols are 6.4 and 6.8, respectively. The corresponding gas permeability coefficients for O₂ are 1.24 and 1.09 Barrers. Compared to the corresponding selectivity and permeability balance reported for polysulfones based on pure BPA, BPA–PSF, the copolymers show a balance that moves in the direction of higher selectivity with small losses in the permeability of the fastest gas. From the glass transition temperature determinations, it is observed that the incorporation of BN in the repeating unit of BPA–PSF inhibits large‐scale segmental motions that are reflected in reductions in the diffusivity coefficients for all gases. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 226–231, 2004     

Synthesis and characterization of novel photoisomerizable liquid crystalline polymers containing cinnamoyl groups

A series of novel liquid crystalline monomers and polymers incorporating phenylbenzoate or phenylcinnamate segments as mesogenic cores have been synthesized to investigate the sensitivity of the photochromic cinnamoyl derivatives and to overcome the defects of the thermal instability of azobenzene. Their liquid crystalline, thermal, and photoinduced properties of all monomers and polymers were characterized. The polymers showed excellent solubility in common organic solvents such as CHCl₃, toluene, and DMF and exhibited good thermal stability with decomposition temperatures (T_d) at 5% weight loss greater than 340 °C and about 50% weight loss occurred beyond 430 °C under nitrogen atmosphere. The pitch length (about 574 nm) of the synthesized cholesteric polymeric film ( CP2 ) was estimated using scanning electron microscopy. These photochromic polymers exhibited strong UV–vis absorption maxima at about 264 or 320 nm. Moreover, photo induced configurational E/Z isomerization further changed the π‐electron conjugation systems leading to a decrease at the π‐π* transition and an increase in the range of 300 nm to 400 nm for photochromic copolymers. The thermal stability of the Z‐structural segment was confirmed by heating the polymer at 50 °C for over 5 h. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1289–1304, 2008     

Sol–gel processed Cu2ZnSnS4 thin films for a photovoltaic absorber layer without sulfurization

Sol–gel processed Cu₂ZnSnS₄ (CZTS) thin films were fabricated without sulfurization for application as a photovoltaic absorber layer. The precursor solution was made from CuCl₂, Zn(ac)₂, SnCl₂, thiourea, and 2-methoxyethanol and the spin-coated film was annealed at temperature above 500 °C under a N₂ atmosphere. A homogeneous and compositionally uniform film with single CZTS phase was obtained. Film composition featuring larger grains, which is desirable in photovoltaic cells, was obtained with heat treatment at 540 °C. The grain size was up to 1 μm and the Cu/(Zn + Sn) and Zn/Sn ratios were 0.93 and 1.07, respectively and the band gap energy was 1.56 eV.     

Copolymerization of ethylene and 1-butene using a Cr—silica catalyst in a slurry reactor

A novel slurry reactor was used to investigate the copolymerization behavior of ethylene and 1-butene in the presence of 1 wt % Cr on Davison silica (Phillips-type) catalyst over the temperature range of 0–50°C, space velocity of about 0.0051 [m³ (STP)]/(g of catalyst) h, and a fixed ethylene to 1-butene feed mole ratio of 95 : 5. The effect of varying the ethylene to 1-butene feed ratios, 100 : 0, 96.5 : 3.5, 95 : 5, 93 : 7, 90 : 10, 80 : 20, and 0 : 100 mol/mol at 50°C was also studied. The addition of 1-butene to ethylene typically increased both copolymerization rates and yields relative to ethylene homopolymerization with the same catalyst, reaching a maximum yield for an ethylene: 1-butene feed ratio of 95 : 5 at 50°C. The incorporation of 1-butene within the copolymer in all cases was less than 5 mol %. The average activation energy for the apparent reaction rate constant, k_a, based on total comonomer mole fraction in the slurry liquid for the ethylene to 1-butene feed mole ratio of 95 : 5 in the temperature range of 50–30°C measured 54.2 kJ/mol. The behavior for temperatures between 30 to 0°C differed with an activation energy of 98.2 kJ/mol; thus, some diffusion limitation likely influences the copolymerization rates at temperatures above 30°C. A kinetics analysis of the experimental data at 50°C for different ethylene to 1-butene feed ratios gave the values of the reactivity ratios, r₁ = 27.3 ± 3.6 and r₂ ≅ 0, for ethylene and 1-butene, respectively. © 1996 John Wiley & Sons, Inc.     

Polymers of carbonic acid. XXVII. Macrocyclic polymerization of trimethylene carbonate

2,2-Dibutyl-2-stanna-1,3-dioxepane (DSDOP) was used as cyclic initiator for the polymerization of trimethylene carbonate (TMC). The polymerizations were either conducted in concentrated chlorobenzene solution at 50 and 80°C or in bulk at 60 and 120°C. With monomer/initiator ratios ≤100 the conversion was complete within 2 h at 80°C and within 12 h at 50°C. Variation of the reaction time revealed that the rapid polymerization is followed by a relatively rapid (backbiting) degradation even at 80°C. The polymerizations in bulk at 60°C were somewhat slower than those at 80°C in solution, but the influence of degradation reactions was less pronounced. With optimized reaction time the number average molecular weight (M_n) roughly parallels the monomer/initiator ratio and M_n's up to 100,000 were obtained. In contrast to a classical living polymerization broader polydispersities (1.5–1.7) were found. In the case of 5,5-dimethyltrimethylene carbonate rapid degradation and chain transfer reactions prevented the formation of high molecular weight polymers. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2179–2189, 1999