Cooperative diffusion in partially neutralized poly(acrylic acid) gels

Poly(acrylic acid) networks swollen with water and having different ionization degrees and different polymer concentrations, were investigated using elastic and quasi-elastic light scattering. The scattered intensity was found to vary as the ratio of the polymer concentration to the ionization degree, which shows that the osmotic pressure is dominated by counterion entropy. The behavior of the cooperative diffusion coefficient cannot be explained by the scaling theories and involves an unexpected variation of the frictional coefficient with polymer concentration.     

Osmotic deswelling of weakly charged poly(acrylic acid) solutions and gels

The osmotic pressure of weakly charged aqueous poly(acrylic acid) (PAA) solutions and the swelling pressure PAA gels were studied by osmotic deswelling at different degrees of ionization (α). In solution, the osmotic pressure was found to scale linearly with concentration, whereas the scaling power of the swelling pressure of gels was higher (1.66). The effect of the ionization degree on the osmotic coefficient in PAA solutions was in agreement with the theory of Borue and Erukhimovich [Macromolecules, 21 , 3240 (1988)]. Ionization increases the swelling capacity of the PAA gels until a plateau is reached at about 35% neutralization. The concentration at equilibrium swelling scales as C_e ～ α^?0.6. The contribution of the network to the gel swelling pressure is evaluated by subtracting the osmotic pressure of the polymer solution at the same concentration and degree of ionization. In swollen gels the extended network opposes swelling. As the gel is osmotically deswelled, a state of zero network pressure exists at a certain concentration, below which the network elasticity favors swelling. The crossover concentration shifts to lower values as the degrees of ionization increases. © 1995 John Wiley & Sons, Inc.     

Brillouin light scattering from poly(vinyl chloride) gels

The hypersonic velocity and attenuation in PVC gels have been measured as a function of gel network volume fraction, using the technique of Brillouin light scattering. The experimental data have been analysed using the full theory for the elastodynamics of gels proposed recently by Johnson. It has been found that for two asymptotic approximations of the dynamic damping factor the tortuosity parameter is nearly always less than unity, contrary to the theoretical expectation.     

Complexation of poly(acrylic acid) and poly(ethylene oxide) investigated by enhanced Rayleigh scattering method

The method of enhanced Rayleigh scattering spectroscopy (ERS) was developed to investigate the complexation of poly(acrylic acid) (PAA) and poly(ethylene oxide) (PEO) in semidilute polymer solutions. Based on the Ornstein‐Zernike equation, the relationship between macromolecular static correlation length and ERS intensity was presented. Moreover, the ERS spectra were calculated by the moving window two‐dimensional (MW2D) correlation spectroscopy to get detailed information of the polymer complexation. The results indicated that the ERS spectroscopy characteristics of the polymer mixtures have similar trend, and the ERS intensity promptly increases as the macromolecular chains contract. The increase of ERS intensity showed that the degree of complexation between PAA and PEO increases when the pH value decreases. The complexation results from the collapse of macromolecular chains, which is induced by the PAA chains contracting and the enhanced association between PAA and PEO chains because of the hydrogen bond formation. In addition, the association resulting from the complexation of PAA and PEO in solution was demonstrated by the MW2D correlation spectroscopy. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1847–1852, 2010     

pH-induced deswelling kinetics of sterically stabilized poly(2-vinylpyridine) microgels probed by stopped-flow light scattering

Near-monodisperse, sterically stabilized poly(2-vinylpyridine) (P2VP) microgels were synthesized by emulsion polymerization. These particles exhibited completely reversible pH-responsive swelling/deswelling behavior in aqueous solution. Stopped-flow light scattering was employed to investigate the kinetics of pH-induced deswelling in highly dilute dispersions. Upon a pH jump from 2 to various final solution pH values (>or=5.4), the scattered light intensity of an aqueous dispersion of a 1,960 nm microgel exhibited an abrupt initial increase, followed by a gradual decrease to the final equilibrium value. The whole microgel-to-latex deswelling process occurred over time scales of approximately 0.5-1.0 s, which is much slower than the kinetics for latex-to-microgel swelling. The microgel deswelling kinetics depends on the final pH, with a higher final pH leading to a faster rate of shrinkage. Close inspection of the deswelling kinetics during the early stages (<0.2 s) revealed that initial microgel collapse occurred within approximately 50 ms, with more rapid transitions being observed when higher final pH values were targeted. Addition of external salt significantly accelerates the kinetics of deswelling. Systematic studies of the microgel-to-latex transition for a series of six near-monodisperse P2VP particles (with swollen microgel diameters ranging from 1270 to 4230 nm) has also been investigated. The characteristic deswelling time for initial microgel collapse, tau deswell, correlated fairly well with the initial swollen microgel radius, R, in agreement with the Tanaka equation. Moreover, the collective diffusion coefficient of the gel network, D, calculated from the slope of the tau deswell- R (2) curve, was of the order of 10 (-7) cm (2) s (-1).     

Micro- and mesoscopic structure of poly(vinyl alcohol) gels determined by neutron and light scattering

We studied the structure of poly(vinyl alcohol) (PVA) gels formed in mixtures of dimethyl sulfoxide (DMSO) and water using several scattering techniques such as wide-angle neutron scattering (WANS), small-angle neutron scattering (SANS), ultra-small-angle neutron scattering (U-SANS) and light scattering (LS) to cover a very wide Q range from 10^-4 to 10 Å^-1. The WANS measurements have revealed that the cross-linking points of the gels are crystallites, and the size and its distribution have been evaluated by the SANS measurements. The SANS results have also shown that the structure observed in the low Q range below 10^-2 Å^-1 is dominated by a liquid–liquid-phase separation. The early stage of the phase separation has been studied in detail using the time-resolved LS technique, while the late stage has been investigated by the U-SANS technique because the LS measurements cannot access the opaque samples. On the basis of the results, we present a quantitative sketch of the structure of the PVA gel.     

Swelling of hydrophobically modified poly(acrylamide) and poly(acrylamide)-co-(acrylic acid) gels in surfactant solutions

A series of hydrophobically modified polyacrylamide and polyacrylamide-co-poly(acrylic acid) gels with systematically varying hydrophobicity were prepared by free-radical polymerization of acrylamide, n-alkylacrylamides (n = 10, 12, and 14), and acrylic acid. The swelling of these gels was examined in water and in both anionic and cationic surfactant solutions. It was found that the gels which incorporated acrylic acid showed extremely high swelling in water. Maximum swelling was observed in gels which incorporated 10 mol% acrylic acid. The swelling of these gels was much less in solutions of both anionic and cationic surfactants than in water. The gels which did not incorporate acrylic acid demonstrated little swelling in water, but showed increased swelling in both anionic and cationic surfactant solutions with increased hydrophobicity of the gel. Received: 1 February 1999 Accepted in revised form: 5 March 1999     

Aggregation and photobleaching of merocyanine 540 as probed by resonance light scattering

Merocyanine 540 (MC540) aggregation induced by adding KCl has been studied by resonance light scattering (RLS) and absorption spectrophotometry. In water, MC540 exists as H-dimers and monomers with absorption maxima at ～500 and 535 nm, respectively (these species lack RLS). Upon the introduction of the salt in concentrations below 0.15 M, the spectrum undergoes a hypochromic effect, without modification of its general shape. In addition to the hypochromic effect, a new broad RLS band emerges at ～420–460 nm, which arises from large H-aggregates of the dye. The formation of these aggregates does not manifest itself in absorption spectra. At KCl concentrations above the critical one (0.15 M), a new absorption band at ～517 nm emerges; simultaneously, a strong RLS band of a similar shape appears, which proves the formation of large supramolecular aggregates of MC540. Comparison of the spectrophotometry and RLS data shows that large aggregates of MC540 are more photolabile than dimers and monomers.     

Preparation and properties of poly(acrylic acid) oligomer stabilized superparamagnetic ferrofluid

Ferrofluids, which are stable dispersions of magnetic particles, behave as liquids that have strong magnetic properties. Nanoparticles of magnetite with a mean diameter of 10-15 nm, which are in the range of superparamagnetism, are usually prepared by the traditional method of co-precipitation from ferrous and ferric electrolyte solution. When diluted, the ferrofluid dispersions are not stable if anionic or cationic surfactants are used as the stabilizer. This work presents an efficient way to prepare a stable aqueous nanomagnetite dispersion. A stable ferrofluid containing Fe3O4 nanoparticles was synthesized via co-precipitation in the presence of poly(acrylic acid) oligomer. The mechanism, microstructure, and properties of the ferrofluid were investigated. The results indicate that the PAA oligomers promoted the nucleation and inhibited the growth of the magnetic iron oxide, and the average diameter of each individual Fe3O4 particle was smaller than 10 nm. In addition, the PAA oligomers provided both electrostatic and steric repulsion against particle aggregation, and the stability of dispersions could be controlled by adjusting the pH value of solution. A small amount of Fe2O3 was found in the nanoparticles but the superparamagnetic behavior of the nanoparticles was not affected.     

The microstructure of poly(vinyl chloride) as revealed by x-ray and light scattering

Small-angle x-ray scattering (SAXS) and wide-angle x-ray scattering (WAXS) as well as small-angle light-scattering (SALS) techniques have been applied to investigate the microstructure of a number of commercial poly(vinyl chloride) (PVC) samples. From the wide-angle x-ray scattering, crystallinity and crystal size parameters have been determined. The crystallinity of the samples investigated range from 5% to 10%. Superstructure parameters such as crystallite thickness, distribution functions of crystallite and amorphous thicknesses, and size of ordered regions have been obtained by an analysis of the SAXS curves using the cluster model. The crystallinity agrees well with the WAXS crystallinities indicating that most of the crystals are lamellar shaped, though some rodlike entities are present in the sample as is shown by the small-angle light scattering. From the SAXS analysis, the microstructure is described as clusters of lamella stacks which are identical with the subprimary particles. Their size is determined to be 220–240 Å. Emulsion type PVC also contains lamellar-shaped crystals. The superstructure, however, of this type of PVC is different from that of mass or suspension-polymerized material. The SAXS curve does not reveal any correlation between the crystals.     

Solvent‐ and counterion‐specific swelling behavior of poly(acrylic acid) gels

The collapse of alkali metal poly(acrylate) (PAAM) gels was investigated for various water/organic solvent mixture systems: methanol (MeOH), ethanol (EtOH), 2‐propanol (2PrOH), t‐butanol (tBuOH), dimethyl sulfoxide (DMSO), acetonitrile (AcN), acetone, tetrahydrofuran (THF), and dioxane. In order to ascertain the counterion specificity in the swelling behavior, four kinds of alkali metal counterions were used: Li⁺, Na⁺, K⁺, and Cs⁺. Remarkable solvent and counterion specificities were observed for every counterion species and every solvent system, respectively. For example, in aqueous EtOH the dielectric constants (D_cr) at which collapse occurred were in the order PAACs < PAALi < PAAK < PAANa. On the other hand, the D_cr at which PAALi gel collapsed increased in the order tBuOH < dioxane < THF < MeOH < 2PrOH < EtOH < acetone < AcN < DMSO, where the D_cr ranged from about 39 to about 67. This was in contrast to our previous observation for a partially quaternized poly(4‐vinyl pyridine) (P4VP) gel, which collapsed in a much narrower D_cr region in similar mixed solvents. The present solvent‐ and counterion‐specific collapses are discussed on the basis of solvent properties such as the dielectric constant and Gutmann's donor number and acceptor number of a pure solvent. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2791–2800, 2000     

Interaction of partially ionized poly(acrylic acid) with a surfactant counterion at constant pH values

Binding of a cationic surfactant ion, dodecylpyridinium ion, to poly(acrylic acids) of low charge densities was examined by potentiometry using surfactant-selective electrodes in the solutions, where the pH was kept constant by employing a pH buffering system. The binding of the surfactant counterions was thus able to be studied at a constant pH during the binding process. The binding took place in two steps, the first cooperative binding step and the second gradual binding step. The critical association concentration decreased as the pH increased, indicating the predominant role of the electric interaction in the binding. The binding isotherms obtained at different but constant pH values were analyzed by the matrix method, taking into account the nearest-neighbor interactions among three different kinds of sites on the polymer: ionized, protonated, and surfactant-bound. The theoretical analysis could describe only the first step but could not explain the second step. A relatively large cooperativity parameter, u, was found for the first step and it can be between 3 × 10³ and 1 × 10⁴. When the ionic strength was decreased tenfold, the cooperativity of the binding decreased (u∼1 × 10³). The binding constants of the isolated site were 5.5–6.0 × 10⁴ kg mol⁻¹ and slightly increased to 6.5 × 10⁴ kg mol⁻¹ as the ionic strength decreased. The deviation of the second step from the theoretical analysis was supposed to arise from a change of proton dissociation constant in the nonpolar space formed by the bound surfactants. Received: 29 November 2000/Accepted: 24 January 2001     

Structure and pH‐sensitive properties of poly (vinylidene fluoride) membrane changed by blending poly (acrylic acid) microgels

pH‐sensitive poly (vinylidene fluoride) (PVDF)/poly (acrylic acid) (PAA) microgels membranes are prepared by phase inversion of the N, N‐dimethylformamide solution containing PAA microgels and PVDF in aqueous solution. The composition and structure of the blend membrane are investigated by Fourier transform infrared spectra, X‐ray photoelectron spectroscopy measurements, thermo gravimetric analysis, field‐emission scanning electron microscope and atomic force microscope. The results indicate the surface and cross section of the blend membranes have a porous structure with PAA microgels immobilized inside the pore and on the membrane surface. The blend PVDF membranes exhibit pH‐sensitive water flux, with the most drastic change in permeability observed between pH 3.7 and 6.3. The blend membranes are fouled by bovine serum albumin, and their antifouling property is enhanced by increasing PAA microgels, mainly derived from the improved hydrophilic property. Copyright © 2013 John Wiley & Sons, Ltd.     

Amphiphilic derivatives of poly(acrylic acid) as stabilizer in emulsion polymerisation

Poly(acrylic acid)s of various molecular weights and different degree of hydrophobic modification have been synthesized by a polymer analogous reaction with tetradecylamine or copolymerization with styrene. Testing these amphiphilic polymers as stabilizers for the emulsion polymerization of styrene reveals that well stabilized latices are obtained within a certain range of molecular weight and hydrophobicity. As an example, the addition of 1 wt.-% polymer with respect to the monomer allows the synthesis of polystyrene latices with a radius of about 100 nm in the absence of ionic initiators or polar comonomers.     

Hydrophobicity of fluoro‐containing physical crosslinkage domains in hydrophobically modified poly(acrylic acid) gels

A series of hydrophobically modified poly(acrylic acid) gels were prepared by the radical copolymerization of acrylic acid and small amounts of hydrophobic comonomers, 2‐(N‐ethylperfluorooctane‐sulfoamido)ethyl methacrylate and lauryl acrylate, in tert‐butanol. The effects of the fractions and species of hydrophobes on hydrophobic association were determined. The hydrophobic association within the hydrophobically modified gels was proven with measurements of swelling and fluorescence as well as Fourier transform infrared spectroscopy. Fluorocarbon‐modified hydrogels showed stronger hydrophobicity than hydrocarbon‐modified hydrogels. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1236–1244, 2002     

Effect of urea on poly(methacrylic acid) and poly(acrylic acid) aqueous solutions

The effects of urea on aqueous solutions of both poly(methacrylic acid (PMA) and poly(acrylic acid) (PAA) have been investigated by using potentiometry, viscometry and study of the fluorescence of Auramine O, a cationic dye. The viscosity behaviour of unionized PMA obtained from direct dissolution of solid powder shows that the unneutralized macromolecules can be associated in water. The stability of such “aggregates” seems weak as indicated by their disappearance as soon as the charge density is very low. For PMA salt solution percolated through a cation (H⁺) exchange resin column, no association is observed. The pH-dependent conformational behaviour of PMA which, contrary to PAA, presents compact conformations in water at low charge density is discussed in terms of solvophobic/solvophilic interactions. It is shown that, even for urea concentration up to 8 M, the compact conformations of PMA are not completely destroyed. The formation of H⁺/urea complex is taken into account.     

Calorimetric investigation of poly(methacrylic acid) and poly(acrylic acid) in aqueous solution

The enthalpy of dissociation of poly(acrylic acid) and of poly(methacrylic acid) in water and in 0.5N NaCl at 25°C has been measured over a wide range of degrees of neutralization of the polyelectrolytes. In the case of poly(methacrylic acid) the calorimetric data permit the direct evaluation of the enthalpy of conformational transition of the polymer. For this transition, with the aid of standard free energy data derived from potentiometric titrations, the change in entropy was also estimated. The relative accuracy of the thermodynamic data, and the possibility of deriving therefrom information on the mechanism of transitions of the type, globular coils → expanded coils for partially hydrophobic synthetic polyelectrolytes in aqueous solution are discussed.     

Pyridine-functionalized single-walled carbon nanotubes as gelators for poly(acrylic acid) hydrogels

Pyridine-functionalized single-walled carbon nanotubes (SWNTs) are prepared from the addition of a pyridine diazonium salt to nanotubes. The location and distribution of the functional groups is determined by atomic force microscopy using electrostatic interactions with gold nanoparticles. The pyridine-functionalized SWNTs are able to act as cross-linkers and hydrogen bond to poly(acrylic acid) to form SWNT hydrogels. The pyridine-functionalized SWNTs are further characterized using Raman, FTIR, UV/vis-NIR, and X-ray photoelectron spectroscopy and thermogravimetric analysis-mass spectrometry.     

Structure and sorption properties of the polyion complex between poly(acrylic acid) and poly(4-vinylpyridine)

A polyion complex was formed from poly(acrylic acid) (PAA) and poly(4-vinylpyridine) (PVP). Its structure and composition were examined by means of infrared spectroscopy (IR), x-ray photoelectron spectroscopy (XPS), and elemental analysis. The polyion complex was obtained by dissolving PAA and PVP together in methanol. The composition of the polyion complex was independent of stirring speed, mixing sequence, and standing time after mixing. However, the composition depended on the concentrations and the ratio of the components in the reaction mixture. Excess of PAA in the product was observed when concentrated solutions (2.0 × 10^?1M) were used for the preparation or when an excess of PAA was added to PVP. The sorption of water vapor by an equimolar PAA/PVP complex at 293 and 303 K was higher than that by the pure components, especially in the low- and middle-pressure regions. In the high-pressure region, however, the uptake was not affected by the complex formation. While hydrogen bond interactions in general decrease sorption, Coulombic interactions between polymer chains increased the sorption capacity.