石英晶体微天平的纳米微球质量放大技术及短序列DNA测定

提出了一种新型质量放大系统用于提高石英晶体微天平检测的灵敏度.将DNA嵌入剂放线菌素D作为导向分子修饰在磁性微球上,通过石英晶体微天平技术识别测定短序列DNA,使最低检测限从6.2×10^-8mol/L下降到2.0×10^-12mol/L.     

石英晶体微天平(QCM)及其在大气腐蚀研究中的应用

从石英晶体微天平的基本原理出发,结合作者的文献调查及近期利用石英晶体微天平对大气腐蚀的研究结果,综述了石英晶体微天平在金属大气腐蚀研究中的重要作用,指出石英晶体微天平在金属大气腐蚀研究中的优点,存在的问题和相应的解决办法。     

Tin corrosion in highly acidic solutions containing ethylene glycol oligomers and halides: An electrochemical quartz crystal microbalance study

Tin corrosion in 1 M H₂SO₄ solutions containing 0.01 M Sn(II), 0.01 M ethylene glycol or its oligomers, and 30 μM of various halides is studied by the electrochemical quartz crystal microbalance method. The current density of the tin electrode corrosion is found to approach a few tens of μA cm^?2. In the presence of Sn(II), the current density is nearly half that in its absence. The corrosion potential steadily increases with time, approaching a certain limit. In solutions containing Sn(II), the limit practically corresponds to the equilibrium potential of the Sn/Sn²⁺ electrode. The corrosion rate barely depends on the oligomer nature even up to tetraethylene glycol. Halides accelerate the corrosion process. Their action intensifies at initial time instants (up to 15–20 min) in the series Cl^? < Br^? < I^?. The corrosion impedance equals ～1000 ohm cm². It may be ignored when analyzing the overall impedance of the tin electrode in the frequency region extending from 0.1 Hz to 50 kHz.     

Improve the signal-to-noise ratio of a quartz crystal microbalance in an impedance analysis method

A new data treatment method for the improvement of the signal-to-noise ratio of a quartz crystal microbalance (QCM) was proposed, where an averaged resonant frequency was calculated according to its conductance peak in an impedance analysis method. The relationship between the averaged resonant frequency and the medians of the conductance peak at different sampling heights was derived. It was shown that the signal-to-noise ratio of the averaged resonant frequency was about eight times of that of the resonant frequency calculated directly from its equivalent circuit parameters. The averaged resonant frequency of the QCM was applied to monitor the self-assembled process of a 6-O-(2′-(α-thiohydroxyacetamide)-ethyl)-diethoxylsilyl-β-cyclodextrin (OTED-β-CD), on gold surface as well as the adsorption of nitrophenol isomers onto the OTED-β-CD self-assembled monolayer film.     

Electrochemical quartz crystal microbalance study of copper ad-atoms on gold and platinum electrodes Part I. Adsorption of anions in sulfuric acid

The deposition and dissolution processes of copper ad-atoms on a gold or a platinum electrode in sulfuric acid electrolyte solution were investigated by using the electrochemical quartz crystal microbalance. It was found that the weight loss in the removal of the Cu-adlayer from the Au substrate was considerably larger than that expected from Faraday's law whereas the deviation for the Pt substrate was very small. The adsorption of bisulfate or sulfate anions both on Cu ad-atoms and on the electrode substrates was discussed quantitatively. It was demonstrated that higher coverage with Cu ad-atoms and lower adsorbability with bisulfate or sulfate anions were obtained on the Pt electrode than on the Au, and these effects could be ascribed to the difference in electronegativity between Pt and Au substrates.     

A multi-technique study of compact and hydrous Au oxide growth in 0.1 M sulfuric acid solutions

The growth and reduction of compact (α-) and overlying hydrous (β-) oxide films on polycrystalline Au electrodes in aqueous 0.1 M H₂SO₄ solutions have been investigated using potentiostatic, cyclic voltammetry, ellipsometric and quartz crystal microbalance (QCMB) techniques. All α-oxide films, formed with time at constant potentials up to 2.6 V, or by multicycling of the potential, are non-hydrated in nature, even when covered by a thick β-oxide film. The α-oxide film composition is suggested to be AuO below 1.5 V, and a mixture of AuO+Au₂O₃ at potentials above this, becoming predominantly Au₂O₃ at very high potentials. Up to three monolayers of Au₂O₃ can be formed. When formed at constant potential, the β-oxide film becomes increasingly hydrated as it thickens with time of growth, with a mass to charge ratio and refractive index consistent with Au₂O₃·H₂O and later with Au₂O₃·2H₂O. In contrast, the β-oxide film formed by multicycling has a higher mass overall, and becomes less hydrated as it thickens with time, with a mass and refractive index consistent with Au₂O₃·10H₂O at short times, ranging to Au₂O₃·2H₂O as the film thickens.     

Determination of molar heats of absorption of enantiomers into thin chiral coatings by combined IC-calorimetric and microgravimetric (QMB) measurements: II. Thermodynamics of enantioselectivity in modified cyclodextrins

A combination of microgravimetric and microcalorimetric measurements was developed for the investigation of enantioselective gas-surface interaction. The sorption behaviour of the two enantiomers of methyl-2-chloropropionate was investigated at polydimethylsiloxane (PDMS) as an achiral receptor and octakis (3-O-butanoyl-2,6-di-O-n-pentyl)-γ-cyclodextrin (Lipodex E^®) as a chiral receptor. The microgravimetric and microcalorimetric results are described by a suitable thermodynamic model providing the thermodynamic data of the absorption process. These data are discussed in terms of the mechanism of chiral recognition and compared to literature data derived from gas chromatographic results by the van’t Hoff method.     

A review on novel developments and applications of immunosensors in food analysis

The present review deals with novel developments in immunosensors destined for final application in food analysis. In this perspective particular emphasis will be given to the most important approaches which recently have been used for immunosensor construction and assembling. For this reason, electrochemical, surface plasmon resonance (SPR) and quartz crystal microbalance (QCM) techniques will be explored in detail and recent and practical examples on food matrices will be reviewed. Objective of this survey is to give a general overview of the possible application of immunosensors to the food analysis field.     

石英晶体微天平实时监测低密度脂蛋白在胆固醇修饰葡聚糖上的吸附及其动力学研究

利用石英晶体微天平实时监测低密度脂蛋白(LDL)在胆固醇修饰葡聚糖(CMD)上的吸附,并对其吸附动力学进行研究.结果表明,CMD与LDL之间的相互作用符合Langmuir吸附方程,当LDL浓度(ng/μL)为9.9,12.38和14.14时,其吸附平衡常数[K/(mol·L-1·s-1)]分别为0.0477,0.0536和0.0628,表面吸附量(ng/cm2)分别为107.6,139.6和167.9.最大吸附量达到284.8ng/cm2,吸附率为72.91%.     

Doping of polyaniline films with organic sulfonic acids in aqueous media and the effect of water on these doped films

Polyaniline (PANI) films in the form of emeraldine salt (ES) doped with aqueous organic sulfonic acids such as camphorsulfonic acid (CSA), p-toluenesulfonic acid (p-TSA) and dodecylbenzenesulfonic acid (DBSA) were studied. The ES films were obtained by treating the PANI in the form of emeraldine base (EB) with the aqueous solution of the acids. The dopant weight fraction (w), which is related to the mass gain during the redoping of EB, was in situ determined using a quartz crystal microbalance (QCM). The behaviour of PANI doping with different acids indicates that the uptake shows a slow diffusion process. The kinetics of the doping reaction is dominated by Fickian diffusion kinetics. The diffusion coefficients (D) of the dopant ions into the PANI chains were determined and were found to vary within the range of (1.6-18) × 10⁻¹⁵ cm² s⁻¹. Moreover, the effect of water on these doped ES films was studied. The starting point is the fact that PANI-coated the electrode of QCM shows significant frequency shifts on exposure to water. The changes in the frequency as a function of treatment time in water were quantitatively measured. The response of the device suggests that the mass decrease under water exposure is due to dopant ions release. The latter films were dedoped by exposure to ammonia solution to obtain the EB film form. A further decrease in the mass of the films was observed. The percentage of the mass loss due to water exposure is found to be less than w determined during the dedoping process.     

Electrodeposition of white gold alloys: an electrochemical,spectroelectrochemical and structural study of the electrodeposition of Au-Sn alloys in the presence of 4-cyanopyridine

A bath for the electrodeposition of Au-Sn alloys is proposed and the properties of the deposit obtained have been studied, in view of applications in the field of white precious metal plating and electroforming. 4-Cyanopyridine has been employed as an organic additive to confer stability to the bath and compactness to the deposit. The electrochemical behaviour of the bath has been investigated by means of cyclic voltammetry, stripping potentiodynamic scans, open circuit potential decay measurements and potentiostatic transients. The nucleation behaviour of the system has been studied on glassy carbon electrodes. The electrodic behaviour of 4-cyanopyridine was investigated as a function of electrode potential by in situ Raman spectroscopy. The composition of the alloys was evaluated by electron dispersive spectroscopy, the crystalline structure by X-ray diffraction and the morphology by scanning electron microscopy. The effects of the additive on the crystalline structure and on the morphology of the electrodeposits have been highlighted. Potential-dependent adsorption, reorientation and cathodic reactivity of 4-cyanopyridine during the alloy electrodeposition process have been assessed.Presented at the 3rd International Symposium on Electrochemical Processing of Tailored Materials held at the 53rd Annual Meeting of the International Society of Electrochemistry, 15–20 September 2002, Düsseldorf, Germany     

Simultaneous electrochemical and piezoelectric microgravimetry measurements of C60 films with a quartz crystal microbalance in a dimethylformamide-water mixed solvent solution containing potassium ions

Simultaneous electrochemistry and piezoelectric microgravimetry studies using electrochemical quartz crystal microbalance were carried out on solution cast C₆₀ films. These films could be reduced in dimethylformamide + water mixture containing potassium ions. It was established that the first reduction was a completely surface-confined process, while the second reduction produced dissolved species. Restricting the potential range only to the first reduction, we could observe reversible electrochemical transformation of the films. Measuring the mass changes of the electrodes during the electrochemical processes, we found that the simple voltammograms (single reduction and oxidation peaks) actually cover simultaneous processes. Both the reduction and the oxidation involved the movements of anions, cations and solvent molecules in and out of the films. It was measured that the initial behavior of the films varied randomly, probably depending on the unpredictable structure of the film produced by solution casting. However, the films adjusted themselves to the experimental conditions displaying steady-state behavior after a certain number of potential scans. This steady-state behavior could be reached independently of the original structure, or the amount of C₆₀ put on the surface, but it could be perturbed easily by altering the conditions. The films were self-adjusted to the measurements.Dedicated to Professor György Horányi on the occasion of his 70th birthday in recognition of his outstanding contributions to electrochemistry     

水汽在涂层中的扩散传输行为和存在形式

利用石英晶体微天平(QCM)为主要手段,研究了水汽在醇酸清漆和聚氨酯清漆涂层中的扩散传输行为.当相对湿度(RH)大于30％时,吸附和脱附动力学都符合Fick第二扩散定律,溶解性遵守Henry定律.计算出了平均扩散系数D.当吸水后的样品重新暴露于干燥空气时,总有一部分水残留于涂层中.傅利叶变换红外光谱仪(FTIR)测定表明吸水前和脱水后涂层分子结构发生了变化.残留水与涂层分子中的羰基C=O形成了氢键.水在涂层中有相当部分可能是以相互置换的链传递方式传输.形成氢键的速度比扩散速度快得多,当RH大于30％时,涂层中水的浓度足以支持其反应,扩散为吸水过程的控制步骤,此时表现为符合Fick第二扩散定律;当RH低于30％时,涂层中水的浓度不足以支持其反应,反应速度降到和扩散速度可相比,此时吸水过程开始偏离Fick第二扩散定律.     

A piezogravimetric sensor platform for sensitive detection of lead (II) ions in water based on calix[4]resorcinarene macrocycles: Synthesis,characterization and detection

The heavy metal ions detection is a foremost concern in water sources, the conventional detection methods are either time consuming or expensive, thus the need of fast, low-cost and accurate sensing methods is growing. Based on this direction, this paper describes the synthesis of newly enantiomeric calix[4]resorcinarenes, namely: C-dec-9-enylcalix[4]resorcinarene-O-(S-)-α-methylbenzylamine (Compound B) and C-dec-9-enylcalix[4]resorcinarene-O-(R+)-α-methylbenzylamine (Compound C), the two macrocycles were the subject of comparative characterization studies using (FTIR, ¹H NMR, ¹³C NMR, TG-DSC-MS, and P-XRD). The realization of modified quartz resonator-gold electrodes, and its introductory employment in the assembly of a novel QCM-I (Quartz Crystal Microbalance with Impedance measurements) based chemosensor for the detection of lead ions in the aqueous solutions is reported for the first time to the best of our knowledge, moreover both Calix-QCM based sensors presented good linearity, acceptable sensitivities, and wide linear ranges, as well as lower detection limits in the order of 0.45 and 0.30 ppm for compounds B and C, consecutively.     

Surface characterisation and crevice corrosion behaviour of nickel-based alloys in the paper industry

Recycled water in the paper industry acts as a stronger electrolyte as its concentration and temperature are quite high. The lower pH that exists in these solutions enhances the corrosion and the high concentration of solids leads to leaching of metal ions from surface. Crevice corrosion is a form of localised attack, which can quickly induce metal perforation even with high grade stainless steels like 316L when the protective chromium oxide film is damaged. A specially designed crevice cell assembly was used to study the electrochemical aspects of nickel-based alloys with the commonly used 316L SS. The mounted specimen with its crevice was anodically polarised in a white water medium, which is normally encountered in the paper machine section. The nickel-based alloys show remarkable crevice corrosion resistance. X-ray photoelectron spectroscopy studies revealed that the enhanced corrosion resistance of these alloys is due to the contributing nature of the individual elements Cr, Ni and Mo and their presence in the form of various oxidised species on the passive films. Received: 22 February 1999 / Accepted: 6 June 1999     

Experimental correlation between metallographic evaluation and electrochemical noise in intergranular corrosion tests of aluminium alloys

In the present work, the correlation between the metallographic evaluation and electrochemical noise (EN) in intergranular corrosion (IGC) tests of aluminium alloy 2024‐T3 has been analysed. For this purpose, the influence of temperature and hydrogen peroxide concentration on the IGC attack has been studied. Similar IGC was observed between 20 and 40 °C, showing a low dependence with temperature (at least in this range). Hydrogen peroxide was seen to have a strong effect, leading to IGC activation when raising its concentration. The results of the detailed metallographic evaluation of the samples after the tests were analysed together with the EN measured during the tests. The averaged noise resistance was inversely proportional to the depths of the attacks, whereas the average of the parameter so‐called ‘Statistical Noise Power’ was directly related to the IGC degree. The metallographic evaluation and the EN showed a reasonable experimental correlation. Copyright © 2012 John Wiley & Sons, Ltd.     

Development of a sensitive detection method of cancer biomarkers in human serum (75%) using a quartz crystal microbalance sensor and nanoparticles amplification system

A simple and sensitive sensor method for cancer biomarkers [prostate specific antigen (PSA) and PSA-alpha 1-antichymotrypsin (ACT) complex] analysis was developed, to be applied directly with human serum (75%) by using antibody modified quartz crystal microbalance sensor and nanoparticles amplification system. A QCM sensor chip consisting of two sensing array enabling the measurement of an active and control binding events simultaneously on the sensor surface was used in this work. The performance of the assay and the sensor was first optimised and characterised in pure buffer conditions before applying to serum samples. Extensive interference to the QCM signal was observed upon the analysis of serum. Different buffer systems were then formulated and tested for the reduction of the non-specific binding of sera proteins on the sensor surface. A PBS buffer containing 200 μg mL⁻¹ BSA, 0.5 M NaCl, 500 μg mL⁻¹ dextran and 0.5% Tween 20, was then selected which eliminated the interfering signal by 98% and enabled the biomarker detection assay to be performed in 75% human serum. By using Au nanoparticles to enhance the QCM sensor signal, a limit of detection of 0.29 ng mL⁻¹ PSA and PSA-ACT complex (in 75% serum) with a linear dynamic detection range up to 150 ng mL⁻¹ was obtained. With the achieved detection limit in serum samples, the developed QCM assay shows a promising technology for cancer biomarker analysis in patient samples.     

Antihypertensive drugs as an inhibitors for corrosion of aluminum and aluminum silicon alloys in aqueous solutions

The corrosion behavior of aluminum and three aluminum–silicon alloys in different concentrations of HCl solutions and its inhibition by antihypertensive drugs was studied using potentiostatic polarization measurements. As the acid concentration increases, the rate of corrosion increases. Aluminum is less susceptible to corrosion than any of Al–Si alloys. The inhibition efficiency of the drug compounds increases with their concentration up to a critical value. At higher additive concentrations the inhibition efficiency starts to decrease. The inhibitive action of these compounds is due to their formation of insoluble complex adsorbed on the metal surface. The adsorption follows Langmuir adsorption isotherms. It was found that the drugs compounds provide protection to Al and Al–Si alloys against pitting corrosion by shifting the pitting potential to more positive direction until critical drug concentrations (250 ppm). After this critical concentration the inhibition against to pitting corrosion starts to decrease.     

Influence of 5-chloro and 5-methyl benzotriazole on the corrosion of copper in acid solution: an experimental and a theoretical approach

The inhibition of copper corrosion in aerated 0.1 mol l⁻¹ hydrochloric acid solutions was studied using electrochemical polarization in the presence of different concentrations of benzotriazole and its two derivatives, 5-chloro and 5-methyl benzotriazole. The inhibition efficiencies obtained from cathodic Tafel plots increased markedly with increase in the additive concentration. Benzotriazole and 5-methyl-benzotriazole were found to be cathodic type corrosion inhibitors for concentrations higher than 10⁻⁴ mol l⁻¹ . However, the 5-chloro-benzotriazole was found to be a mixed inhibitor for concentrations up to 10⁻³ mol l⁻¹, above this concentration the inhibitor behaves as an anodic type inhibitor. The inhibitors are physisorbed on the copper surface following a Langmuir’s isotherm. The inhibition efficiencies depended on the inhibitor concentration and follows the order 5-chloro-benzotriazole > 5-methyl-benzotriazole > 1-H-benzotriazole. From the theoretical calculations, the change in the inhibition mechanism observed for 5-chloro-benzotriazole at concentrations higher than 10⁻³ mol l⁻¹ is associated with the electronic acceptor characteristic of chloro, which increases the benzotriazole acidity allowing the formation of CuBTA.