Effects of doping with nanoscale Co3O4 particles on the superconducting properties of powder-in-tube processed MgB2 tapes

Nanoscale Co₃O₄ particles were doped into MgB₂ tapes with the aim of developing superconducting wires with high-current-carrying capacity. Fe-sheathed MgB₂ tapes with a mono-core were prepared using the in situ powder-in-tube (PIT) process with the addition of 0.2–1.0 mol% Co₃O₄. The critical temperature decreased monotonically with an increasing amount of doped Co₃O₄ particles for all heat-treatment temperatures from 600 to 900 °C. However, the transport critical current density (J_c) at 4.2 K varied with the heat-treatment temperatures. The J_c values in magnetic fields ranging from 7 to 12 T decreased monotonically with increasing Co₃O₄ doping level for a heat-treatment temperature of 600 °C. In contrast, some improvements on the J_c values of the Co₃O₄ doped tapes were observed in the magnetic fields below 10 T for 700 and 800 °C. Furthermore, J_c values in all the fields measured increased as the Co₃O₄ doping level increase from 0 to 1 mol% for 900 °C. This heat-treatment temperature dependence of the J_c values could be explained in terms of the heat-treatment temperature dependence of the irreversibility field with Co₃O₄ doping.     

Electrochemical supercapacitor studies of hierarchical structured Co2+-substituted SnO2 nanoparticles by a hydrothermal method

Hierarchical structured Co-doped SnO₂ nanoparticles are prepared by a low temperature hydrothermal process. The structural and surface morphologies of the SnO₂ and Sn_1?xCo_xO₂ nanoparticles are studied by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM), and scanning electron microscopy (SEM). The Sn_1?xCo_xO₂ nanoparticles form with a tetragonal rutile structure during the hydrothermal process without further calcination. The pseudocapacitance behavior of the Sn_1?xCo_xO₂ nanoparticles is characterized by cyclic voltammetry (CV) in 1.0 M H₂SO₄ electrolyte. The specific capacitance (SC) is found to increase with an increase in cobalt content. A maximum SC of 840 F g^?1 is obtained for a Sn_0.96Co_0.04O₂ composite at a 10 mV s^?1 scan rate.     

Application of indium tin oxide (ITO) thin film as a low emissivity film on Ni-based alloy at high temperature

Indium tin oxide (ITO) films as the low emissivity coatings of Ni-based alloy at high temperature were studies. ITO films were deposited on the polished surface of alloy K424 by direct current magnetron sputtering. These ITO-coated samples were heat-treated in air at 600–900 °C for 150 h to explore the effect of high temperature environment on the emissivity. The samples were analyzed by X-ray diffraction (XRD), SEM and EDS. The results show that the surface of sample is integrity after heat processing at 700 °C and below it. A small amount of fine crack is observed on the surface of sample heated at 800 °C and Ti oxide appears. There are lots of fine cracks on the sample annealed at 900 °C and a large number of various oxides are detected. The average infrared emissivities at 3–5 μm and 8–14 μm wavebands were tested by an infrared emissivity measurement instrument. The results show the emissivity of the sample after annealed at 600 and 700 °C is still kept at a low value as the sample before annealed. The ITO film can be used as a low emissivity coating of super alloy K424 up to 700 °C.     

Theoretical investigation of the inversion parameter in Co3 − sAlsO4 (s = 0–3) spinel structures

The structural, energetic, and thermodynamic properties of the Co_3 ? sAl_sO₄ (s = 0, 1, 2, and 3) crystal family are studied using periodic DFT calculations. We provide a quantitative discussion of the cation distribution effect on the cell parameter, the oxygen Wyckoff position, the interatomic distances and the energies of the structures. It is demonstrated that the low cobalt containing CoAl₂O₄ spinel is the most stable structure of the Co_3 ? sAl_sO₄ (s = 0, 1, 2, and 3) crystal family.     

Solid state reduction of chromium (VI) pollution for Al2O3–Cr metal ceramics application

Reduction of chromium (VI) from Na₂CrO₄ through aluminothermic reaction and fabrication of metal-ceramic materials from the reduction products have been investigated in this study. Na₂CrO₄ could be successfully reduced into micrometer-sized Cr particles in a flowing Ar atmosphere in presence of Al powder. The conversion ratio of Na₂CrO₄ to metallic Cr attained 96.16% efficiency. Al₂O₃–Cr metal-ceramic with different Cr content (5 wt%, 10 wt%, 15 wt%, 20 wt%) were further prepared from the reduction product Al₂O₃–Cr composite powder, and aluminum oxide nanopowder via pressure-less sintering. The phase composition, microstructure and mechanical properties of metal-ceramic composites were characterized to ensure the potential of the Al₂O₃–Cr composite powder to form ceramic materials. The highest relative density and bending strength can reach 93.4% and 205 MP, respectively. The results indicated that aluminothermic reduction of chromium (VI) for metal-ceramics application is a potential approach to remove chromium (VI) pollutant from the environment.     

Effect of Al content on impact resistance behavior of Al-Ti-B4C composite fabricated under air atmosphere

Reaction behavior, mechanical property and impact resistance of TiC-TiB₂/Al composite reacted from Al-Ti-B₄C system with various Al content via combination method of combustion synthesis and hot pressed sintering under air was investigated. Al content was the key point to the variation of mechanical property and impact resistance. Increasing Al content could increase the density, strength and toughness of the composite. Due to exorbitant ceramic content, 10 wt.% and 20 wt.% Al-Ti-B₄C composites exhibited poor molding ability and machinability. Flexural strength, fracture toughness, compressive strength and impact toughness of 30–50 wt.% Al-Ti-B₄C composite were higher than those of Al matrix. The intergranular fracture dispersed and defused impact load and restricted crack extension, enhancing the impact resistance of the composite. The composite with 50 wt.% Al content owned highest mechanical properties and impact resistance. The results were useful for the application of TiC-TiB₂/Al composite in impact resistance field of ceramic reinforced Al matrix composite.     

Significant enhancement of electrical transport properties of thermoelectric Ca3Co4O9+δ through Yb doping

We report the significant enhancement of the power factor of Ca₃Co₄O_9+δ through Yb doping. The pellets were prepared by pressing under 0.5 GPa and 2 GPa. The highest power factor of 553 μW m^?1 K^?2 due to the significant increase of electrical conductivity was obtained for Ca_2.9Yb_0.1Co₄O_9+δ pressed at 0.5 GPa. This is 2.3 times higher than that of Ca₃Co₄O_9+δ (246 μW m^?1 K^?2). Nanostructure examinations show that the pellets pressed at 0.5 and 2 GPa have different nano-lamella structures. This work suggests that Yb is an effective doping element for enhancing the electrical transport properties of Ca₃Co₄O_9+δ, and the optimum doping level is related to the nanostructure of the bulk pellets.     

Suppression of structural degradation of LiNi0.9Co0.1O2 cathode at 90 °C by AlPO4-nanoparticle coating

This study examined the electrochemical and structural stability of ∼1.5 wt.% AlPO₄-coated LiNi_0.9Co_0.1O₂. The AlPO₄-coated LiNi_0.9Co_0.1O₂ retained ∼60% of the original capacity after 50 cycles, compared with the ∼30% capacity retention of the bare LiNi_0.9Co_0.1O₂. The discharge profiles and cyclic voltammograms from 4.5 V at 90 °C for 4 h showed enhanced structural stability. Scanning electron microscopy and X-ray diffraction revealed that the AlPO₄-coated LiNi_0.9Co_0.1O₂ had less degradation than the bare LiNi_0.9Co_0.1O₂.     

Sonochemical synthesis and characterization of Co3O4 nanocrystals in the presence of the ionic liquid [EMIM][BF4]

For the first time, a sonochemical process has been used to synthesis cobalt oxide Co₃O₄ nanoflowers and nanorods morphology in the presence of the ionic liquid 1-Ethyl-3-methylimidazolium tetrafluoroborate [EMIM][BF₄] as reaction media and morphology template. Different sonication time periods and different molar ratios of the ionic liquid (IL) were used to investigate their effects on the structural, optical, chemical and magnetic properties of the produced Co₃O₄ nanoparticles. During synthesis process brown powder contains cobalt hydroxide Co(OH)₂ and cobalt oxyhydroxide (Cobalt hydroxide oxide) CoO(OH) was formed, after calcination in air for 4 h at 400 °C a black powder of Co₃O₄ nanoparticles was produced. The produced Co₃O₄ nanoparticles properties were characterized by X-ray diffraction (XRD), Field Emission Scanning Electron Microscopy (FE-SEM), transmission electron microscopy (TEM), FTIR spectroscopy, UV–vis spectroscopy, and Vibrating Sample Magnetometer (VSM). To explain the formation mechanism of Co₃O₄ NPs some investigations were carried on the brown powder before calcination.     

Electrical conductivity and oxygen permeation properties of SrCoFeOx membranes

The total conductivity and oxygen permeation properties of dense SrCoFeO_x membranes synthesized from the solid state method were studied in the temperature range of 700–900 °C. The SrCoFeO_x membranes consist of an intergrowth (Sr₄Fe_6 − xCo_xO_13 ± δ), perovskite (SrFe_1 − xCo_xO_3 − δ), and spinel (Co_3 − xFe_xO₄) phase. SrCoFeO_x exhibits n-type and p-type conduction at low and high oxygen partial pressures, respectively, and has a total conductivity of 16.5 S/cm at 900 °C in air. The oxygen permeation fluxes for SrCoFeO_x and SrFeCo_0.5O_x membranes were measured with either an inert or carbon monoxide sweep gas. The oxygen permeation fluxes were higher through SrCoFeO_x membranes than SrFeCo_0.5O_x membranes and can be attributed to a difference in the amount and makeup of the perovskite phase present in each composition. The oxygen permeation fluxes with a carbon monoxide sweep gas were approximately two orders of magnitude larger than the fluxes measured with an inert sweep gas for both compositions. The large oxygen permeation fluxes observed with a carbon monoxide sweep are due to a higher driving force for oxygen transport and a reaction on the sweep side of the membrane that maintains a low oxygen partial pressure.     

Cobalt terephthalate MOF-templated synthesis of porous nano-crystalline Co3O4 by the new indirect solid state thermolysis as cathode material of asymmetric supercapacitor

In this work, two different types of Co₃O₄ nano-crystals were synthesized by (i) conventional direct solid state thermolysis of cobalt terephthalate metal-organic framework (MOF-71) and (ii) new indirect solid state thermolysis of Co(OH)₂ derived by alkaline aqueous treatment of MOF-71. The products were then characterized by X-ray diffraction technique (XRD), Fourier transforms infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), Reflection electron energy loss spectroscopy (REELS), Brunauer, Emmett, and Teller (BET), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) techniques. By REELS analysis the energy band gap of MOF-71 was determined to be 3.7 eV. Further, electrochemical performance of each Co₃O₄ nanostructure was studied by the cyclic voltammetry (CV), galvanostatic charge-discharge (GCD), and electrochemical impedance spectroscopy (EIS) in a three-electrode system in KOH electrolyte. An asymmetric supercapacitor was fabricated using indirect Co₃O₄ nanoparticles as cathode and electrochemically reduced graphene oxide as anode, and the electrochemical properties were studied and showed a high energy density of 13.51 Wh kg⁻¹ along with a power density of 9775 W kg⁻¹ and good cycling stability with capacitance retention rate of 85% after 2000 cycles.     

Microstructure evolution process of Ferro-Aluminum based sandwich composite for electromagnetic shielding

In this paper, sandwich composite (SWC) with Fe–Al soft magnetic alloy sandwiched between pure iron substrates was proposed and fabricated by hot pressing and diffusion treatment. The microstructure evolution process of the composite was investigated. Fe/Fe₂Al₅/Fe diffusion couple was obtained at 700 °C and subsequently kept at 900 °C for further isothermal diffusion. During the diffusion reactive process, we confirmed that major FeAl₂ and minor Fe₄Al₁₃ were produced when Fe₂Al₅ dissolved. After 10 h of diffusion treatment, FeAl and α-Fe(Al) were the only two intermetallic phases left. Except FeAl₂, the thickness of each intermetallic layer held good parabolic relationship with the diffusion annealing time.     

A-deficit LSCF for intermediate temperature solid oxide fuel cells

A-deficit La_0.54Sr_0.44Co_0.2Fe_0.8O_3 ? δ cathode material for intermediate temperature solid oxide fuel cells (IT-SOFCs) was synthesized by a citrate complexation (Pechini) route. Using La_0.54Sr_0.44Co_0.2Fe_0.8O_3 ? δ as cathode material, a superior cell performance with the maximum power density of 309, 470 and 855 mW cm^? 2 at 600, 650 and 700 °C was achieved, in contrast with the maximum power density of 266, 354 and 589 mW cm^? 2 using conventional La_0.6Sr_0.4Co_0.2Fe_0.8O_3 ? δ as cathode material at the same temperatures. The reason of this improvement was analyzed on the basis of defect chemistry. Thermal shrinkage experiment testified that the oxygen vacancies in La_0.54Sr_0.44Co_0.2Fe_0.8O_3 ? δ are more mobile than in La_0.6Sr_0.4Co_0.2Fe_0.8O_3 ? δ. Furthermore, theoretical calculation in terms of their composition and the shift of peak position in XRD pattern showed that the concentration of oxygen vacancies of La_0.54Sr_0.44Co_0.2Fe_0.8O_3 ? δ is higher than that of La_0.6Sr_0.4Co_0.2Fe_0.8O_3 ? δ. Therefore, the oxygen ion conductivity via vacancies transfer mechanism is enhanced, which induces the polarization resistance of La_0.54Sr_0.44Co_0.2Fe_0.8O_3 ? δ being decreased with a result of cell performance improved.     

Spectroscopic properties of Co2+: ZnAl2O4 nanocrystals in sol–gel derived glass–ceramics

Transparent glass–ceramics containing zinc–aluminum spinel (ZnAl₂O₄) nanocrystals doped with tetrahedrally coordinated Co²⁺ ions were obtained by the sol–gel method for the first time. The gels of composition SiO₂–Al₂O₃–ZnO–CoO were prepared at room temperature and heat-treated at temperature ranging 800–950 °C. When the gel samples were heated up to 900 °C, ZnAl₂O₄ nanocrystals were precipitated. Co²⁺ ions were located in tetrahedral sites in ZnAl₂O₄ nanocrystals. X-ray diffraction analysis shows that the crystallite sizes of ZnAl₂O₄ crystal become large with the heat-treatment temperature and time, and the crystallite diameter is in the range of 10–15 nm. The dependence of the absorption and emission spectra of the samples on heat-treatment temperature were presented. The difference in the luminescence between Co²⁺ doped glass–ceramic and Co²⁺ doped bulk crystal was analysed. The crystal field parameter D_q of 423 cm⁻¹ and the Racah parameters B of 773 cm⁻¹ and C of 3478.5 cm⁻¹ were calculated for tetrahedral Co²⁺ ions.     

The influence of some processing conditions on host crystal structure and phosphorescence properties of SrAl2O4:Eu2+, Dy3+ nanoparticle pigments synthesized by combustion technique

The spectroscopic and host phase properties of SrAl₂O₄:Eu²⁺, Dy³⁺ phosphors with a series of different initiating combustion temperature, urea concentration as a fuel and critical pH of precursor solution are investigated. The SrAl₂O₄:Eu²⁺, Dy³⁺ nanoparticle pigments were obtained by exothermic combustion process within less than 5 min. The sample that ignited at initiating combustion temperature of 600 °C exhibits highest intensity emission peak at 517 nm in which the SrAl₂O₄ host phase has the maximum fraction of monoclinic SrAl₂O₄ phase. The excitation spectra consist of 240 and 254 nm broad peaks. The experimental results show that the optimum ratio of urea is 2.5 times higher than theoretical quantities for best emission condition of SrAl₂O₄:Eu²⁺, Dy³⁺ phosphor particles. The critical pH was obtained about 5.2. The crystallite size of these pigments is about 40 nm before thermal treatment and 62 nm after thermal treatment, respectively.     

Above-gap and subgap differential conductance anomaly in concentrated magnetic semiconductor Zn0.32Co0.68O1 − v/Pb superconductor hybrid junctions

The Zn_0.32Co_0.68O_1 − v/Pb hybrid junctions were prepared, where the concentrated magnetic semiconductor Zn_0.32Co_0.68O_1 − v is in the region of variable range hopping transport instead of the ballistic or diffusive transport. The high differential conductance peak at gap voltage and two above-gap peaks were observed below the superconducting critical temperature. Moreover, both the zero bias conductance peak and the finite bias conductance peak were observed below the gap voltage. All these differential conductance peaks systematically evolve and finally disappear as the temperature or the magnetic field increases. These transport phenomena were explained by phase coherent Andreev reflection in the presence of strong disorder, magnetic impurity scattering, and spin polarization.     

The studies on structural and thermal properties of delithiated LixNi1/3Co1/3Mn1/3O2 (0 < x ≤ 1) as a cathode material in lithium ion batteries

The structural and thermal properties of the delithiated Li_xNi_1/3Co_1/3Mn_1/3O₂ (0 < x ≤ 1) material have been investigated by using diffraction and thermoanalytical techniques such as XRD and TG-DSC methods. XRD result shows that the delithiated materials maintain the O3-type structure with defined stoichiometric number at the range of 0.24 < x ≤ 1, exhibiting good crystal structural stability. The cobalt and nickel ions in the delithiated materials change their valence state (i.e. Co³⁺ to Co⁴⁺ and Ni³⁺ to Ni⁴⁺) when x < 0.49; the irreversible changes of the transformation may affect the first cycle of charge–discharge efficiency of the materials. A comparison of the results of TG-DSC with TPD-MS shows that the irreversible change of oxygen species during the delithiation process of Li_xNi_1/3Co_1/3Mn_1/3O₂ have great influence on the structural and thermal stability and reversibility of the materials.     

Thermal expansion behavior and chemical compatibility of BaxSr1−xCo1−yFeyO3−δ with 8YSZ and 20GDC

Perovskite oxides of the composition Ba_xSr_1−xCo_1−yFe_yO_3−δ(BSCF) were synthesized via a modified Pechini method and characterized by X-ray diffraction, dilatometry and thermogravimetry. Investigations revealed that single-phase perovskites with cubic structure can be obtained for x ≤ 0.6 and 0.2 ≤ y ≤ 1.0. The as-synthesized BSCF powders can be sintered in several hours to nearly full density at temperatures of over 1180 °C. Thermal expansion curves of dense BSCF samples show nonlinear behavior with sudden increase in thermal expansion rate between about 500 °C and 650 °C, due mainly to the loss of lattice oxygen caused by the reduction of Co⁴⁺ and Fe⁴⁺ to lower valence states. Thermal expansion coefficients (TECs) of BSCF were measured to be 19.2–22.9 × 10^− 6 K^− 1 between 25 °C and 850 °C. Investigations showed further that Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ is chemically compatible with 8YSZ and 20GDC for temperatures up to 800 °C, above which severe reactions were detected. After being heat-treated with 8YSZ or 20GDC for 5 h above 1000 °C, Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ was completely converted to phases like SrCoO_3−δ, BaCeO₃, BaZrO₃, etc.     

Structure sensitivity of propene oxidation over Co-Mn spinels

Single-phase cobalt–manganese spinel oxides (Co_3?nMn_nO₄, CMO) were studied for the catalytic oxidation of propene in a systematic optimization strategy. CMO films were synthesized by pulsed-spray evaporation chemical vapor deposition (PSE–CVD) and characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR), Raman and Ultraviolet–Visible (UV–Vis) spectroscopy. The effect of Co/Mn ratio in the mixed oxide systems on their catalytic activity was investigated in a fixed-bed reactor at T = 100–800 °C, with a space velocity of 90,000 mL/g_cat h and a feed of 2% C₃H₆/20% O₂/78% Ar. XRD patterns, FTIR and Raman spectroscopy reveal that a cubic single-phase spinel structure is obtained for n ? 1.23, while a tetragonal spinel structure is observed for n > 1.23. With increasing of the manganese content, the temperature–programmed analysis demonstrates a lower reducibility, a general decrease of the temperature required for the reduced samples to be re-oxidized and increasing thermal stability. The catalytic tests show that the involvement of cobalt–manganese oxides in propene oxidation suppresses the formation of reaction intermediates, favoring the selectivity toward CO₂ at low temperatures. Co_2.35Mn_0.65O₄ exhibits the best catalytic performance, which follows in line with its better reducibility compared with the other compositions in the series of CMO oxides. These results show the great potential of CMO for future industrial application as a low-temperature catalytic system which does not rely on precious metals.