Selective hydrogenation by polymer-encapsulated platinum nanoparticles prepared by an easy single-step sonochemical synthesis

Polypyrrole-encapsulated platinum nanoparticles (PPy/Pt-NPs) prepared by an easy single-step sonochemical synthesis were used as catalysts for the liquid phase hydrogenation of substituted alkenes in methanol or methanol/water mixtures. Polypyrrole (PPy) coatings on the nanoparticles were able to act as nanoscopic filters for substrates molecules, and consequently substrate selectivity could be controlled in the catalytic processes.     

Deposition and characterization of Cu(In,Ga)Se2 thin films from the ink of sonochemically prepared CIGSe nanoparticles

CuIn_1-xGa_xSe₂ (CIGSe) nanoparticles were synthesized via a sonochemical method at different Ga content (x?=?0.15, 0.30 and 0.45) and dispersed in a low toxic isobutanol to form the nanoparticle-ink. Thin films of CIGSe were grown by a facile, non-vacuum and inexpensive “nanoparticle-ink based air-spray coating” method. Effects of Ga-content and annealing time on the physical properties of CIGSe thin films were investigated. The elemental composition, crystalline structure, surface morphology and optical properties of the films were explored by various characterization methods. XRD studies of as-synthesized films showed a tetragonal structure with (112) orientation. After annealing, the CIGSe films showed an improvement in the intensity ratio of I(220)/I(112) for the annealing time of 60?min. The morphological studies of annealed CIGSe films showed plank-like larger grains of size ～1–2?µm. The films deposited at different gallium content, x?=?0.15, 0.30 and 0.45 showed PL peak maxima at 954, 1049 and 1168?nm, respectively. The present method is capable of producing CIGSe absorbers by a greener route in large scales at lower cost.     

Highly sensitive breath sensor based on sonochemically synthesized cobalt-doped zinc oxide spherical beads

In this study, we introduce cobalt (Co)-doped zinc oxide (ZnO) spherical beads (SBs), synthesized using a sonochemical process, and their utilization for an acetone sensor that can be applied to an exhalation diagnostic device. The sonochemically synthezied Co-doped ZnO SBs were polycrystalline phases with sizes of several hundred nanometers formed by the aggregation of ZnO nanocrystals. As the Co doping concentration increased, the amount of substitutionally doped Co²⁺ in the ZnO nanocrystals increased, and we observed that the fraction of Co³⁺ in the Co-doped ZnO SBs increased while the fraction of oxygen vacancies decreased. At an optimal Co-doping concentration of 2 wt%, the sensor operating temperature decreased from 300 to 250 °C, response to 1 ppm acetone improved from 3.3 to 7.9, and minimum acetone detection concentration was measured at 43 ppb (response, 1.75). These enhancements are attributed to the catalytic role of Co³⁺ in acetone oxidation. Finally, a sensor fabricated using 2 wt% Co-doped ZnO SBs was installed in a commercially available exhalation diagnostic device to successfully measure the concentration of acetone in 1 ml of exhaled air from a healthy adult, returning a value of 0.44 ppm.     

Characterization of sonochemically prepared human serum albumin nanocapsules using different plant oils as core component for targeted drug delivery

The focus of this study is the preparation of proteinaceous human serum albumin (HSA) nanocapsules with biocompatible plant oil cores avoiding toxic cross-linker and noxious non-aqueous liquids. The sonochemical preparation of HSA capsules with different plant oils yields particles with narrow size distribution forming suspensions stable for at least 14 days and enabling long-term storage by freezing. Furthermore, wheat germ agglutinin (WGA) as a targeting molecule was successfully embedded into the proteinaceous particle shell at a molar ratio of 7:1 (HSA/WGA). As urothelial cell binding studies revealed up to 55% higher cell binding potential of WGA-grafted particles than those without a targeter, targeted protein nanocapsules represent the first step towards new and innovative formulations.     

Structural analysis of sonochemically prepared Au/Pd nanoparticles dispersed in porous silica matrix

Bimetallic Au/Pd nanoparticles supported on a silica matrix were prepared by an ultrasonic technique. The samples heat-treated at 100, 200, 300 and 400 degrees C were examined with techniques of XRD (X-ray diffraction), TEM and XAS (X-ray absorption spectrometry) for studying correlation between their structure and the catalytic activity of hydrogenation of cyclohexene. Even after the heat treatment at 400 degrees C, the particles were smaller than 20 nm and well dispersed in the matrix without agglomeration nor sintering. Results of the XRD, TEM and XAS indicated that the as-prepared particles have a core/shell structure of Au/Pd and transform into a random alloy at 300 degrees C. The catalysis seemed to be deactivated by alloying.     

Structural change of mesoporous silica with sonochemically prepared gold nanoparticles in its pores

Ultrasonic irradiation of mesoporous silica soaked in a mixture of chloroauric acid and isopropanol for 120 min in Ar atmosphere at room temperature yielded Au/SiO₂ mesoporous composite, which was characterized by high resolution transmission electron microscopy and optical absorption measurement. The structure of mesoporous silica after sonochemical preparation of gold (Au) nanoparticles within its pores was studied by nitrogen adsorption technique. It has been shown that the structural parameters, such as specific surface area (SSA), porosity (P), the mean pore diameter (l_p) were increased significantly after ultrasonic irradiation. It is suggested that the collision of Au nanoparticles with pore walls and localized erosion induced by the asymmetric implosive collapse of cavities on the extensive liquid–solid interface that are responsible for the structural change in the mesoporous solid.     

XPS analysis of sonochemically prepared SbSI ethanogel

This paper, for the first time, presents the results of the X-ray photoelectron spectroscopy (XPS) of the valence band and core levels in sonochemically prepared SbSI ethanogel consisting of nanowires. The XPS spectra were measured with monochromatized Al K_α radiation in the energy range of 0-1400 eV at room temperature. It was found that the sonochemically prepared SbSI ethanogel is a p-type semiconductor. The XPS determined composition of this material suggests the existence of antimony subiodide at surfaces of SbSI nanowires. The chemical shifts in SbSI ethanogel for the Sb, I and S states are reported. Experimentally obtained binding energies are compared with the results reported for single crystals of SbSI.     

Sonochemical assisted synthesis of SrFe12O19 nanoparticles

We present the synthesis of M-type strontium hexaferrite by sonochemistry and annealing. The effects of the sonication time and thermal energy on the crystal structure and magnetic properties of the obtained powders are presented. Strontium hexagonal ferrite (SrFe₁₂O₁₉) was successfully prepared by the ultrasonic cavitation (sonochemistry) of a complexed polyol solution of metallic acetates and diethylene glycol. The obtained materials were subsequently annealed at temperatures from 300 to 900 °C. X-ray diffraction analysis shows that the sonochemical process yields an amorphous phase containing Fe³⁺, Fe²⁺ and Sr²⁺ ions. This amorphous phase transforms into an intermediate phase of maghemite (γ-Fe₂O₃) at 300 °C. At 500 °C, the intermediate species is converted to hematite (α-Fe₂O₃) by a topotactic transition. The final product of strontium hexaferrite (SrFe₁₂O₁₉) is generated at 800 °C. The obtained strontium hexaferrite shows a magnetization of 62.3 emu/g, which is consistent with pure hexaferrite obtained by other methods, and a coercivity of 6.25 kOe, which is higher than expected for this hexaferrite. The powder morphology is composed of aggregates of rounded particles with an average particle size of 60 nm.     

Sonochemical synthesis of versatile hydrophilic magnetite nanoparticles

Hydrophilic magnetite nanoparticles in the size range 30-10 nm are easily and rapidly prepared under ultrasonic irradiation of Fe(OH)₂ in di- and tri-ethylene glycol/water solution with volume ratio varying between 7:3 and 3:7.Structural (XRD) and morphological (SEM) characterization reveal good crystalline and homogeneous particles whereas, when solvothermally prepared, the particles are inhomogeneous and aggregated. The sonochemically prepared particles are versatile, i.e. well suited to covalently bind molecules because of the free glycol hydroxylic groups on their surface or exchange the diethylene or triethylene glycol ligand. They can be easily transferred in hydrophobic solvents too.Room-temperature magnetic hysteresis properties measured by means of Vibrating Sample Magnetometer (VSM) display a nearly superparamagnetic character.The sonochemical preparation is easily scalable to meet industrial demand.     

Ultrasound assisted chitosan coated iron oxide nanoparticles: Influence of ultrasonic irradiation on the crystallinity,stability, toxicity and magnetization of the functionalized nanoparticles

Due to unique reaction conditions of the acoustic cavitation process, ultrasound-assisted synthesis of nanoparticles has attracted increased research attention. In this study, we demonstrate the effect of ultrasonic irradiation on the crystallinity, stability, biocompatibility, and magnetic properties of chitosan-coated superparamagnetic iron oxide nanoparticles (CS-SPIONs). CS solution and colloidal suspension of SPIONs were mixed and sonicated using an ultrasonic probe of 1.3 cm tip size horn, frequency (20 kHz), and power (750 W). Different samples were sonicated for 1.5, 5, and 10 min with corresponding acoustic powers of 67, 40 and 36 W, and the samples were denoted S_1.5, S_5, and S₁₀, respectively. The samples were characterized using X-ray diffractometer (XRD), Energy dispersive X-ray (EDX), Transmission electronic microscope (TEM), Fourier transform infrared spectroscopy (FTIR), Zeta sizer, and vibrating sample magnetometer (VSM). Cell cytotoxicity and cell uptake were investigated with human embryonic kidney 293 (HEK-293) cells through MTT assay and Prussian blue staining, respectively. The sharp peaks of the XRD pattern were disappearing with an increase in the sonication period but a decrease in acoustic power. EDX analysis also demonstrates that atomic and weight percentages of the various elements in the samples were decreasing with an increase in the sonication period. However, the Zeta potential (ζ) values increase with an increase in the sonication period.The saturation magnetization (M_s) of the S_1.5 before and after the coating is 62.95 and 86.93 emu/g, respectively. Cell cytotoxicity and uptake of the S_1.5 show that above 70% of cells were viable at the highest concentration and the longest incubation duration. Importantly, the CS-SPIONs synthesized by the sonochemical method are non-toxic and biocompatible.     

Using of sonochemically prepared SbSI for electrospun nanofibers

A novel polymeric, polyacrylonitrile (PAN) nanofibers containing ferroelectric and semiconducting antimony sulfoiodide (SbSI) have been made by electrospinning. SbSI nanowires, used as the filler, have been prepared sonochemically from antimony sulphide (Sb₂S₃) and antimony tri-iodide (SbI₃) for the first time. Nanocrystalline SbSI has been fabricated in ethanol under ultrasonic irradiation (20 kHz, 565 W/cm²) at 323 K within 2 h. The products have been characterized by using techniques such as powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, high-resolution transmission electron microscopy, selected area electron diffraction and optical diffuse reflection as well as transmission spectroscopy. The good quality of the nanocrystals and their dispersion in the nanofiber’s volume is important because this material is attractive for nanogenerators due to its ferroelectric and piezoelectric properties. The amplitude of the voltage pulse, generated under shock pressure of 3.0 MPa, has reached 180 V in the prototype PAN/SbSI piezoelectric nanogenerator. The peak output voltage of about 0.2 V was measured in bending/releasing conditions with the deformation frequency of 1 Hz.     

Synthesis of TiO2/WO3 nanoparticles via sonochemical approach for the photocatalytic degradation of methylene blue under visible light illumination

Through an ultrasound assisted method, TiO₂/WO₃ nanoparticles were synthesized at room temperature. The XRD pattern of as-prepared TiO₂/WO₃ nanoparticles matches well with that of pure monoclinic WO₃ and rutile TiO₂ nanoparticles. TEM images show that the prepared TiO₂/WO₃ nanoparticles consist of mixed square and hexagonal shape particles about 8–12 nm in diameter. The photocatalytic activity of TiO₂/WO₃ nanoparticles was tested for the degradation of a wastewater containing methylene blue (MB) under visible light illumination. The TiO₂/WO₃ nanoparticles exhibits a higher degradation rate constant (6.72 × 10⁻⁴ s⁻¹) than bare TiO₂ nanoparticles (1.72 × 10⁻⁴ s⁻¹) under similar experimental conditions.     

Sonochemical synthesis,structural, magnetic and grain size dependent electrical properties of NdVO4 nanoparticles

NdVO₄ nanoparticles are successfully synthesized by efficient sonochemical method using two different structural directing agents like CTAB and P123. The phase formation and functional group analysis are carried out using X-ray diffraction (XRD) and fourier transform infra red (FT-IR) spectra, respectively. Using Scherrer equation the calculated grain sizes are 27 nm, 24 nm and 20 nm corresponding to NdVO₄ synthesized by without surfactant, with CTAB and P123, respectively. The TEM images revealed that the shape of NdVO₄ particles is rice-like and rod shaped particles while using CTAB and P123 as surfactants. The growth mechanism of NdVO₄ nanoparticles is elucidated with the aid of TEM analysis. From electrical analysis, the conductivity of NdVO₄ nanoparticles synthesized without surfactant showed a higher conductivity of 5.5703 × 10⁻⁶ S cm⁻¹. The conductivity of the material depends on grain size and increased with increase in grain size due to the grain size effect. The magnetic measurements indicated the paramagnetic behavior of NdVO₄ nanoparticles.     

Aligned carbon nanotubes catalytically grown on iron-based nanoparticles obtained by laser-induced CVD

Iron-based nanoparticles are prepared by a laser-induced chemical vapor deposition (CVD) process. They are characterized as body-centered Fe and Fe₂O₃ (maghemite/magnetite) particles with sizes ≤5 and 10 nm, respectively. The Fe particles are embedded in a protective carbon matrix. Both kind of particles are dispersed by spin-coating on SiO₂/Si(1 0 0) flat substrates. They are used as catalyst to grow carbon nanotubes by a plasma- and filaments-assisted catalytic CVD process (PE-HF-CCVD). Vertically oriented and thin carbon nanotubes (CNTs) were grown with few differences between the two samples, except the diameter in relation to the initial size of the iron particles, and the density. The electron field emission of these samples exhibit quite interesting behavior with a low turn-on voltage at around 1 V/μm.     

Sonochemical synthesis of carbon supported Sn nanoparticles and its electrochemical application

A sonochemical approach was employed to prepare Vulcan carbon XC-72R supported by Sn nanoparticles at room temperature in the presence of ethylene glycol. The reduction of metallic Sn ion and ethylene glycol takes place and in turn the glycolate ion as formed acts as a stabilizing agent. Transmission electron microscope, X-ray diffraction, and X-ray photoelectron spectroscopy have illustrated that the metallic Sn nanoparticles are successfully embedded on the carbon. The significantly observed reduction over potential for oxygen reduction reaction displays a higher catalytic activity of carbon supported by Sn nanoparticles due to the large surface area of the modified electrode.     

Optimization of ultrasonic-assisted approach for synthesizing a highly stable biocompatible bismuth-coated iron oxide nanoparticles using a face-centered central composite design

The incorporation of additional functional groups such as bismuth nanoparticles (Bi NPs) into magnetite nanoparticles (Fe₃O₄ NPs) is critical for their properties modification, stabilization, and multi-functionalization in biomedical applications. In this work, ultrasound has rapidly modified iron oxide (Fe₃O₄) NPs via incorporating their surface through coating with Bi NPs, creating unique Fe₃O₄@Bi composite NPs. The Fe₃O₄@Bi nanocomposites were synthesized and statistically optimized using an ultrasonic probe and response surface methodology (RSM). A face-centered central composite design (FCCD) investigated the effect of preparation settings on the stability, size, and size distribution of the nanocomposite. Based on the numerical desirability function, the optimized preparation parameters that influenced the responses were determined to be 40 ml, 5 ml, and 12 min for Bi concentration, sodium borohydride (SBH) concentration, and sonication time, respectively. It was found that the sonication time was the most influential factor in determining the responses. The predicted values for the zeta potential, hydrodynamic size, and polydispersity index (PDI) at the highest desirability solution (100%) were −45 mV, 122 nm, and 0.257, while their experimental values at the optimal preparation conditions were −47.1 mV, 125 nm, and 0.281, respectively. Dynamic light scattering (DLS) result shows that the ultrasound efficiently stabilized and functionalized Fe₃O₄NPs following modification to Fe₃O₄@Bi NPs, improved the zeta potential value from –33.5 to −47.1 mV, but increased the hydrodynamic size from 98 to 125 nm. Energy dispersive spectroscopy (EDX) validated the elemental compositions and Fourier transform infrared spectroscopy (FTIR) confirmed the presence of Sumac (Rhus coriaria) compounds in the composition of the nanocomposites. The stability and biocompatibility of Fe₃O₄@Bi NPs were improved by using the extract solution of the Sumac edible plant. Other physicochemical results revealed that Fe₃O₄NPs and Fe₃O₄@Bi NPs were crystalline, semi-spherical, and monodisperse with average particle sizes of 11.7 nm and 19.5 nm, while their saturation magnetization (Ms) values were found to be 132.33 emu/g and 92.192 emu/g, respectively. In vitro cytotoxicity of Fe₃O₄@Bi NPs on the HEK-293 cells was dose- and time-dependent. Based on our findings, the sonochemical approach efficiently produced (and RSM accurately optimized) an extremely stable, homogeneous, and biocompatible Fe₃O₄@Bi NPs with multifunctional potential for various biomedical applications.     

Sonochemical fabrication of inorganic nanoparticles for applications in catalysis

Catalysis covers almost all the chemical reactions or processes aiming for many applications. Sonochemistry has emerged in designing and developing the synthesis of nano-structured materials, and the latest progress mainly focuses on the synthetic strategies, product properties as well as catalytic applications. This current review simply presents the sonochemical effects under ultrasound irradiation, roughly describes the ultrasound-synthesized inorganic nano-materials, and highlights the sonochemistry applications in the inorganics-based catalysis processes including reduction, oxidation, degradation, polymerization, etc. Or all in all, the review hopes to provide an integrated understanding of sonochemistry, emphasize the great significance of ultrasound-assisted synthesis in structured materials as a unique strategy, and broaden the updated applications of ultrasound irradiation in the catalysis fields.     

Unique sharp photoluminescence of size-controlled sonochemically synthesized zirconia nanoparticles

The present study explores the features of tetragonally stabilized polycrystalline zirconia nanophosphors prepared by a sonochemistry based synthesis from zirconium oxalate precursor complex. The sonochemically prepared pristine zirconia, 3 mol%, 5 mol% and 8 mol% yttrium doped zirconia nanophosphors were characterized using thermo-gravimetric analysis (TGA), X-ray diffraction (XRD), Raman spectroscopy, field emission scanning electron microscopy (FE-SEM) with energy dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS) and photoluminescence spectroscopy (PL). The reaction mechanism of formation of zirconia nanophosphors is discussed in detail. The probable sonochemical formation mechanism is being proposed. Stabilization of tetragonal phase of pristine zirconia even at room temperature was effectively established by controlling the particle size using ultrasonic waves. Improved phase purity and good surface morphology of the nanophosphors is being achieved via sonochemical route. FE-SEM micrographs reveal that the nanoparticles have uniform spherical shape and size. The narrow particle size distribution (∼15–25 nm) of the zirconia nanoparticles was found from FE-SEM statistical analysis and further confirmed by TEM. Zirconia nanophosphors exhibit a wide energy band gap and which was found to vary with yttrium dopant concentration. The highlight of the present study is the synthesis of novel nanocrystalline ZrO₂ and Y-ZrO₂ phosphor which simultaneously emits extremely sharp as well as intense UV, violet and cyan light on exciting the host atom. The yttrium ion dopant further enhances the photoluminescence property of zirconia. These nanocrystalline phosphors are likely to have remarkable optical applications as light emitting UV-LEDs, UV lasers and multi color displays.     

Fabrication and characterization of silver/titanium dioxide composite nanoparticles in ethylene glycol with alkaline solution through sonochemical process

This paper aims to study fabrication and characterization of silver/titanium oxide composite nanoparticle through sonochemical process in the presence of ethylene glycol with alkaline solution. By using ultrasonic irradiation of a mixture of silver nitrate, the dispersed TiO₂ nanoparticle in ethylene glycol associated with aqueous solution of sodium oxide yields Ag/TiO₂ composite nanoparticle with shell/core-type geometry. The powder X-ray diffraction (XRD) of the Ag/TiO₂ composites showed additional diffraction peaks corresponding to the face-centered cubic (fcc) structure of silver crystallization phase, apart from the signals from the cores of TiO₂. Transmission electron microscopy (TEM) images of Ag/TiO₂ composites, which average particle size is roughly 80 nm, reveal that the titanium oxide coated by Ag nanoparticle with a grain size of about 2–5 nm. Additionally, the formation of silver nanoparticles on TiO₂ was monitored by ultraviolet visible light spectrophotometer (UV–Vis). As measured the optical absorption spectra of as-synthesized Ag nanoparticle varying with time, the mechanism of surface formatting silver shell on the cores of TiO₂ could be explored by autocatalytic reaction; the conversion of Ag particle from silver ion is 98% for the reaction time of 1000 s; and the activity energy of synthesizing Ag nanoparticles on TiO₂ is 40 kJ/mol at temperature ranging from 5 to 25 °C. Hopefully, this preliminary investigation could be used for mass production of composite nanoparticles assisted by ultrasonic chemistry in the future.