超声波作用下污泥水分扩散过程的数值模拟

建立了超声波作用下污泥内部水分扩散模型,利用分形理论对超声波(20 kHz)作用下污泥内部孔隙结构进行描述,探讨了超声波声能密度对污泥孔隙表面分形维数df及孔隙通道曲折度分形维数dw的影响,在此基础上建立了超声波作用下多孔介质中液体有效扩散系数的分形模型,对不同声能密度超声波辐照下污泥水分扩散过程进行了数值模拟.研究发...     

Comparison between airborne ultrasound and contact ultrasound to intensify air drying of blackberry: Heat and mass transfer simulation,energy consumption and quality evaluation

This study aimed at investigating the performances of air drying of blackberries assisted by airborne ultrasound and contact ultrasound. The drying experiments were conducted in a self-designed dryer coupled with a 20-kHz ultrasound probe. A numerical model for unsteady heat and mass transfer considering temperature dependent diffusivity, shrinkage pattern and input ultrasonic energies were applied to explore the drying mechanism, while the energy consumption and quality were analyzed experimentally. Generally, both airborne ultrasound and contact ultrasound accelerated the drying process, reduced the energy consumption and enhanced the retentions of blackberry anthocyanins and organic acids in comparison to air drying alone. At the same input ultrasound intensity level, blackberries received more ultrasound energies under contact sonication (0.299 W) than airborne sonication (0.245 W), thus avoiding the attenuation of ultrasonic energies by air. The modeling results revealed that contact ultrasound was more capable than airborne ultrasound to intensify the inner moisture diffusion and heat conduction, as well as surface exchange of heat and moisture with air. During air drying, contact ultrasound treatment eliminated the gradients of temperature and moisture inside blackberry easier than airborne ultrasound, leading to more homogenous distributions. Moreover, the total energy consumption under air drying with contact ultrasound assistance was 27.0% lower than that with airborne ultrasound assistance. Besides, blackberries dehydrated by contact ultrasound contained more anthocyanins and organic acids than those dried by airborne ultrasound, implying a higher quality. Overall, direct contact sonication can well benefit blackberry drying in both energy and quality aspects.     

Ultrasound pretreatment of wheat dried distiller’s grain (DDG) for extraction of phenolic compounds

Wheat Dried distiller’s grain (DDG), a coproduct from the ethanol production process, is rich in potentially health-promoting phenolic compounds. In the extraction of phenolic compounds from DDG, the DDG cell wall is an important barrier for mass transfer from the inside to the outside of the cell. The effect of high-power ultrasound pretreatment on destruction of DDG cell walls and extraction yield and rate was investigated. Direct sonication by an ultrasound probe horn at 24 kHz was applied and factors such as ultrasound power and treatment time were investigated. The method of nitrogen (N₂) adsorption at 77 K was used as a means to determine and compare the changes in physical properties (specific surface area, pore volume and pore size) of the treated samples at different levels of ultrasound power and treatment time. Increasing specific surface area, pore volume and pore size caused by ultrasonic treatment implied development of new or larger pores and damaged cell walls. Also, it was observed that the ultrasound pretreatment of DDG particles increased the extraction yield and rate of phenolic compounds from DDG by 14.29%. Among tested ultrasound conditions, 100% ultrasound power for 30 s was evaluated as the best pretreatment condition.     

Assessment of sonotrode and tube reactors for ultrasonic pre-treatment of two different sewage sludge types

The effectiveness of tube and sonotrode reactors for the sonication of sewage sludge under identical conditions was compared for the first time. Despite the considerable structural differences, sonication with each ultrasonic reactor led to an accelerated degradation rate and an increased methane production within the first five days for the majority of the sewage sludge samples tested. On closer examination, however, it becomes clear that the investigated sonication systems are not equally suitable for the substrates considered. While the use of a sonotrode proved to be particularly advantageous for the treatment of waste activated sludge (+25% methane yield at 300 kJ/kg_TS), the use of a 2-inch tube reactor achieved the highest enhancement for low-intensity sonication in digested sludge (+22% methane yield at 300 kJ/kg_TS). With increasing energy input, more chemical oxygen demand was solubilized, but this did not result in an increase in methane yield for all samples. Sonication of waste activated sludge led to a significant reduction in viscosity of up to 50%, and a reduction of up to 60% was observed after sonication of digested sludge with low energy inputs. The study, therefore, demonstrates that the choice of the most suitable sonication system essentially depends on the properties of the sludge to be sonicated.     

Ultrasound assisted chitosan coated iron oxide nanoparticles: Influence of ultrasonic irradiation on the crystallinity,stability, toxicity and magnetization of the functionalized nanoparticles

Due to unique reaction conditions of the acoustic cavitation process, ultrasound-assisted synthesis of nanoparticles has attracted increased research attention. In this study, we demonstrate the effect of ultrasonic irradiation on the crystallinity, stability, biocompatibility, and magnetic properties of chitosan-coated superparamagnetic iron oxide nanoparticles (CS-SPIONs). CS solution and colloidal suspension of SPIONs were mixed and sonicated using an ultrasonic probe of 1.3 cm tip size horn, frequency (20 kHz), and power (750 W). Different samples were sonicated for 1.5, 5, and 10 min with corresponding acoustic powers of 67, 40 and 36 W, and the samples were denoted S_1.5, S_5, and S₁₀, respectively. The samples were characterized using X-ray diffractometer (XRD), Energy dispersive X-ray (EDX), Transmission electronic microscope (TEM), Fourier transform infrared spectroscopy (FTIR), Zeta sizer, and vibrating sample magnetometer (VSM). Cell cytotoxicity and cell uptake were investigated with human embryonic kidney 293 (HEK-293) cells through MTT assay and Prussian blue staining, respectively. The sharp peaks of the XRD pattern were disappearing with an increase in the sonication period but a decrease in acoustic power. EDX analysis also demonstrates that atomic and weight percentages of the various elements in the samples were decreasing with an increase in the sonication period. However, the Zeta potential (ζ) values increase with an increase in the sonication period.The saturation magnetization (M_s) of the S_1.5 before and after the coating is 62.95 and 86.93 emu/g, respectively. Cell cytotoxicity and uptake of the S_1.5 show that above 70% of cells were viable at the highest concentration and the longest incubation duration. Importantly, the CS-SPIONs synthesized by the sonochemical method are non-toxic and biocompatible.     

Modal content of noise generated by a coaxial jet in a pipe

The problem investigated was that of noise generated by air flow through a coaxial obstruction in a long, straight pipe of inside diameter, D = 97 mm. Downstream modal pressure spectra in the 200–6000 Hz frequency range were measured by a new technique [1] for orifices and nozzles of diameter d where $\text{0·03 ? (}\text{d}\text{D}\text{) ? 0·52}$. The Mach numbers of the flow through the restrictions ranged from 0·15 to choked conditions. The shape of the modal frequency spectrum was found to be determined by the frequency ratio $\text{f}{}_{\mathrm{r}}\text{=}\text{He}\text{St}\text{=}\text{U}{}_{\mathrm{i}}\text{D}\text{a}{}_0\text{d}$, where U_i is the jet velocity and a₀ is the speed of sound in the gas downstream of the restriction. This parameter is the ratio of two non-dimensional frequencies: namely, He, which controls acoustic propagation inside circular ducts, and St, which scales the jet noise spectrum shape. At low f_r(<3) the higher modes dominate the noise spectrum above their cut-off frequencies, while for higher f_r all modes are approximately of equal amplitude. The nature of large scale turbulence structures in the region of the jet near the nozzle exit may be used to explain these phenomena. The measured modal pressure spectra were converted to modal power spectra and integrated over the frequency range 200–6000 Hz. The acoustic efficiency levels (acoustic power normalized by jet kinetic energy flow), when plotted vs. jet Mach number, depend strongly on the ratio of restriction diameter to pipe diameter ($\text{d}\text{D}$). Dividing the efficiency levels by the area ratio, $\text{(}\text{d}\text{D}\text{)}{}^2$, correlated the results over a moderate range of ($\text{d}\text{D}$).     

Influence of material structure on air-borne ultrasonic application in drying

This work aims to contribute to the understanding of how the properties of the material being dried affect air-borne ultrasonic application. To this end, the experimental drying kinetics (40 °C and 1 m/s) of cassava (Manihot esculenta) and apple (Malus domestica var. Granny Smith) were carried out applying different ultrasonic powers (0, 6, 12, 19, 25 and 31 kW/m³). Furthermore, the power ultrasound-assisted drying kinetics of different fruits and vegetables (potato, eggplant, carrot, orange and lemon peel) already reported in previous studies were also analyzed. The structural, textural and acoustic properties of all these products were assessed, and the drying kinetics modeled by means of the diffusion theory.A significant linear correlation (r > 0.95) was established between the identified effective diffusivity (D_W) and the applied ultrasonic power for the different products. The slope of this relationship (SDUP) was used as an index of the effectiveness of the ultrasonic application; thus the higher the SDUP, the more effective the ultrasound application. SDUP was well correlated (r ⩾ 0.95) with the porosity and hardness. In addition, SDUP was largely affected by the acoustic impedance of the material being dried, showing a similar pattern with the impedance than the transmission coefficient of the acoustic energy on the interface. Thus, soft and open-porous product structures exhibited a better transmission of acoustic energy and were more prone to the mechanical effects of ultrasound. However, materials with a hard and closed-compact structure were less affected by acoustic energy due to the fact that the significant impedance differences between the product and the air cause high energy losses on the interface.     

Formation of an ensemble of nanoclusters under rapid deposition of atoms on a surface

The results of an experimental study of the formation of nanometer-size Au clusters on NaCl(100) and HOPG(0001) surfaces under pulsed laser deposition are presented. No clusters of small sizes (d ≤ 1 nm) have been found in the cluster size distribution. The distribution itself at d < 5 nm has the form of a percolation distribution. It has been established that the perimeter of clusters with sizes d < 5 nm has a fractal structure. The fractal dimension of clusters is different for NaCl(100) and HOPG(0001) surfaces with different symmetries; it decreases with increasing cluster size from D _f ≈ 1.2–1.4 at d ≈ 1.5 nm to D _f ≈ 1 at d ≈ 5 nm. A physical mechanism of nanocluster formation is suggested. Under pulsed laser deposition, the attainable densities of adatoms are close to the percolation threshold in the region of thermodynamically unstable states and many-particle correlation regions are formed in a spatially inhomogeneous adsorbate. Clusters are formed on the surface from many-particle correlation regions in several diffusion jumps. The suggested mechanism allows the fractal dimension of the clusters forming on surfaces with different symmetries, its dependence on cluster size, and the cluster size distribution functions to be calculated.     

Characterising the cavitation activity generated by an ultrasonic horn at varying tip-vibration amplitudes

Dual-perspective high-speed imaging and acoustic detection is used to characterise cavitation activity at the tip of a commercial 20 kHz (f₀) ultrasonic horn, over 2 s sonications across the range of input powers available (20 – 100%). Imaging at 1 × 10⁵ frames per second (fps) captures cavitation-bubble cluster oscillation at the horn-tip for the duration of the sonication. Shadowgraphic imaging at 2 Mfps, from an orthogonal perspective, probes cluster collapse and shock wave generation at higher temporal resolution, facilitating direct correlation of features within the acoustic emission data generated by the bubble activity. f₀/m subharmonic collapses of the primary cavitation cluster directly beneath the tip, with m increasing through integer values at increasing input powers, are studied. Shock waves generated by periodic primary cluster collapses dominate the non-linear emissions of the cavitation noise spectra. Transitional input powers for which the value of m is indistinct, are identified. Overall shock wave content within the emission signals collected during sonications at transitional input powers are reduced, relative to input powers with distinct m. The findings are relevant for the optimisation of applications such as sonochemistry, known to be mediated by bubble collapse phenomena.     

Ultrasonic pretreatment of corn slurry for saccharification: A comparison of batch and continuous systems

The effects of ultrasound on corn slurry saccharification yield and particle size distribution was studied in both batch and continuous-flow ultrasonic systems operating at a frequency of 20 kHz. Ground corn slurry (28% w/v) was prepared and sonicated in batches at various amplitudes (192–320 μm_{peak-to-peak (p–p)}) for 20 or 40 s using a catenoidal horn. Continuous flow experiments were conducted by pumping corn slurry at various flow rates (10–28 l/min) through an ultrasonic reactor at constant amplitude of 12 μm_p–p. The reactor was equipped with a donut shaped horn. After ultrasonic treatment, commercial alpha- and gluco-amylases (STARGEN^TM 001) were added to the samples, and liquefaction and saccharification proceeded for 3 h. The sonicated samples were found to yield 2–3 times more reducing sugars than unsonicated controls. Although the continuous flow treatments released less reducing sugar compared to the batch systems, the continuous flow process was more energy efficient. The reduction of particle size due to sonication was approximately proportional to the dissipated ultrasonic energy regardless of the type of system used. Scanning electron microscopy (SEM) images were also used to observe the disruption of corn particles after sonication. Overall, the study suggests that both batch and continuous ultrasonication enhanced saccharification yields and reduced the particle size of corn slurry. However, due to the large volume involve in full scale processes, an ultrasonic continuous system is recommended.     

Ultrasound-enhanced coagulation for Microcystis aeruginosa removal

Source water eutrophication has caused serious problems in drinking water supplies, with enhanced coagulation widely used to remove the resulting algae. This paper investigates the use of sonication to improve the removal by coagulation of Microcystis aeruginosa, a common species of toxic algae. The results show that sonication significantly enhances the reduction of algae cells, solution UV254, and chlorophyll a without increasing the concentration of aqueous microcystins. The main mechanism involved the destruction during ultrasonic irradiation of gas vacuoles inside algae cells that acted as ‘nuclei’ for acoustic cavitation and collapse during the “bubble crush” period, resulting in the settlement of cyanobacteria. Coagulation efficiency depended strongly on the coagulant dose and sonication conditions. When the coagulant dose was 0.5 mg/l, 5 s of ultrasonic irradiation increased algae removal efficiency from 35% to 67%. As further sonication enhanced the coagulation efficiency only slightly due to better mixing, optimal sonication time was 5 s. The most effective sonication intensity was 47.2 W/cm², and the highest removal ratio of M. aeruginosa was 93.5% by the sonication–coagulation method. Experiments with reservoir water showed that this method could be successfully applied to natural water containing multiple species of algae.     

Power ultrasound as a pretreatment to convective drying of mulberry (Morus alba L.) leaves: Impact on drying kinetics and selected quality properties

The effect of ultrasound pretreatment prior to convective drying on drying kinetics and selected quality properties of mulberry leaves was investigated in this study. Ultrasound pretreatment was carried out at 25.2–117.6 W/L for 5–15 min in a continuous mode. After sonication, mulberry leaves were dried in a hot-air convective dryer at 60 °C. The results revealed that ultrasound pretreatment not only affected the weight of mulberry leaves, it also enhanced the convective drying kinetics and reduced total energy consumption. The drying kinetics was modeled using a diffusion model considering external resistance and effective diffusion coefficient D_e and mass transfer coefficient h_m were identified. Both D_e and h_m during convective drying increased with the increase of acoustic energy density (AED) and ultrasound duration. However, D_e and h_m increased slowly at high AED levels. Furthermore, ultrasound pretreatment had a more profound influence on internal mass transfer resistance than on external mass transfer resistance during drying according to Sherwood numbers. Regarding the quality properties, the color, antioxidant activity and contents of several bioactive compounds of dried mulberry leaves pretreated by ultrasound at 63.0 W/L for 10 min were similar to that of mulberry leaves without any pretreatments. Overall, ultrasound pretreatment is effective to shorten the subsequent drying time of mulberry leaves without damaging the quality of final product.     

Effects of combined ultrasonic and microwave vacuum drying on drying characteristics and physicochemical properties of Tremella fuciformis

This study analyzes the effects of ultrasonic waves on the drying kinetics of Tremella fuciformis during microwave vacuum drying. The physicochemical properties and structural characteristics of T. fuciformis polysaccharides (TFPs) were studied by drying tremella samples using hot air drying (HAD), microwave vacuum drying, ultrasonic pretreatments with microwave vacuum drying (US + MVD), and air-borne ultrasonic pretreatments combined with microwave vacuum drying (USMVD) under acoustic energy densities of 0.14, 0.28, and 0.42 W/mL. The results showed that USMVD and US + MVD accelerated the mass transfer process of T. fuciformis. Compared with HAD treatment, TFP samples obtained by USMVD and US + MVD had a reduced molecular weight to a certain extent, and they had stronger shear thinning ability. In addition, USMVD-TFPs at 0.42 W/mL retained higher total sugar, reducing sugar, and uronic acid, and the degree of reduction in the monosaccharide component content was small.     

Propagation of Hermite-cosh-Gaussian laser beams in n-InSb

The propagation of Hermite-cosh-Gaussian (HChG) laser beams in n-InSb are investigated for 0, 1 and 2 mode indices. The field distribution in the medium is expressed in terms of beam-width parameter f and decentred parameter b. The differential equations for f-parameter are established by parabolic wave equation approach under paraxial approximation. Analytical solutions are obtained under the condition R_n < R_d, where, R_n is the self-focusing length and R_d is the diffraction length. The behaviour of f-parameter with the dimensionless distance of propagation η for various b values is examined by numerical estimates. The results are presented graphically.     

Nonradiative decay from 5d states of rare earths in crystals

Nonradiative decay from 4f^n?1 5d states was investigated for trivalent rare earths in Y₃Al₅O₁₂. The rates of both 5d→4f and 5d→5d transitions were determined from measurements of the lifetimes and intensities of 5d fluorescence from Ce³⁺ and Pr³⁺. Because of the stronger ion-lattice coupling, nonradiative decay rates for transitions involving 5d states are much faster than those between 4f states. Decay rates are dependent upon the temperature and the energy gap to the next-lower level. The temperature dependences of the 5d fluorescence lifetimes from 77 to 700°K are reported.     

Structural properties and scaling of the radius of gyration of two-dimensional star-branched polymers grown by diffusion

We built up star-branched polymers, whose morphology is fully determined by diffusion, with p=1,3,6 and 12 branches with a total of 30,000 monomer units. We investigated their structural properties by calculating the monomer-monomer correlation functions. A detailed finite size scaling analysis of the radius of gyration was also performed to determine the exponent and the corrections to scaling. From these results we calculated the fractal dimension of the branched aggregates and obtained: d_f=1.222(7), for the linear chain, d_f=1.2305(8), d_f=1.247(8) and d_f=1.261(8) for the three, six and twelve branches polymer, respectively.     

Quantification of surface area and intrinsic mass transfer coefficient for ultrasound-assisted dissolution process of a sparingly soluble solid dispersed in aqueous solutions

The efficacy of power ultrasound of 20 kHz in enhancing the volumetric mass transfer coefficient was investigated in this study. Breakage and dissolution of sparingly soluble benzoic acid dispersed in either water or 24% aqueous glycerol was monitored as a function of time and ultrasound power input. Particle size measurements were carried out at intermediate times during the experiment to estimate the mean particle size and surface area. Linear combination of lognormal distributions was found to fit the experimental particle size distribution data. The De Brouckere mean diameters (d₄₃) obtained from the particle size distributions decreased with increase in the ultrasonic power level. Empirical correlations were developed for the evolution of surface area as a function of ultrasonic energy input per unit mass. The effect of ultrasound on the intrinsic mass transfer coefficient (k_c) could be decoupled from the volumetric mass transfer coefficient (k_ca) as the surface area was also estimated. Different approaches involving either constant or variable intrinsic mass transfer coefficients were employed when carrying out the delineation. Mass transfer rates were enhanced due to both higher ultrasound induced intrinsic convective mass transfer coefficient and additional surface area created from particle breakage. To delineate the effects of particle breakage from solid dissolution, experiments were also carried out under non-mass transfer conditions by pre-saturating the solvents with benzoic acid. Both the solid-liquid systems examined in the present study attained saturation concentration when the ultrasonic energy input per unit mass was approximately 60 kJ/kg, irrespective of the ultrasonic power level setting.     

Revised model for 5d electrons in the heavy rare earth metals

A revised version of a recently published model for 5d electrons in the ferromagnetic state of the heavy rare earth metals is described. The model involves the broadening of local 5d states into overlapping bands with individual widthsW. In the new approach it is assumed that the local 5d wave functions lie at some point between those for atomic 4f _n 5d 6s ² configurations and those calculated for such configurations subject to the restriction that the 4f shell is kept with its moment rigidly fixed in some given direction. The admixture of non-aligned 4f states as in the atom lowers the local energy, but it also lowers the 5d bandwidth due to misfit of the 4f states which occur with and without the presence of a 5d electron. This second effect raises the energy of the low lying states in the band. The best local states are determined by minimising the total electronic energy of the system, using approximations which are most suitable for 4f shells with large excitation energies. Bandwidths are found by fitting the observed saturation magnetic moments in Gd and Tm, and satisfyW?1 eV.     

A verification of the occurrence of the downconversion effect (transformation of a quantum of VUV radiation into two photons of luminescence in the visible range) in KGd2F7 and K2GdF5 crystals doped with Tb3+ ions

In order to verify whether the downconversion mechanism can occur in KGd₂F₇ and K₂GdF₅ crystals, which contain different concentrations of Tb³⁺ ions, we have investigated the emission and luminescence-excitation spectra of these crystals. Our experimental results have not shown the occurrence of the downconversion effect in the examined crystals, since the rate of nonradiative relaxation from upper 4f5d levels to lower-lying 4f5d- and 4f levels of the Tb³⁺ ion is likely to exceed the rate of possible cross relaxation from these high-lying 4f5d levels with energy transfer to neighboring Tb³⁺ ions.     

Sonochemical synthesis and characterization of lead iodide hydroxide micro/nanostructures

For the first time, micro/nano-sized lead iodide hydroxide; Pb(OH)I, has been successfully prepared via a simple ultrasonic method. In this method, lead nitrate and lithium iodide were applied as starting reagents to fabricate Pb(OH)I micro/nanostructures at different conditions. The effect of different surfactants like N,N-bis(salicylidene)-ethylenediamine (H₂salen), sodium dodecyl sulfate (SDS) and polyvinylpyrrolidone (PVP), sonication time, and ultrasonic intensity on the morphology and particle size of the products has been investigated. The as-produced micro/nanostructures were characterized with the aid of XRD, SEM, TEM, UV–vis, EDS and FT-IR. According to the SEM images, different morphologies of Pb(OH)I including micro- and nano-sized rods were formed by changing the preparation conditions. Based on the XRD results, it was found that Pb(OH)I and PbI₂ have been produced with and without sonication at the same conditions, respectively. The use of the H₂salen and sonication treatment were confirmed to be the crucial factors determining the formation of one-dimensional Pb(OH)I micro/nanostructures.