Using high haze (> 90%) light-trapping film to enhance the efficiency of a-Si:H solar cells

The high haze light-trapping (LT) film offers enhanced scattering of light and is applied to a-Si:H solar cells. UV glue was spin coated on glass, and then the LT pattern was imprinted. Finally, a UV lamp was used to cure the UV glue on the glass. The LT film effectively increased the Haze ratio of glass and decreased the reflectance of a-Si:H solar cells. Therefore, the photon path length was increased to obtain maximum absorption by the absorber layer. High Haze LT film is able to enhance short circuit current density and efficiency of the device, as partial composite film generates broader scattering light, thereby causing shorter wave length light to be absorbed by the P layer so that the short circuit current density decreases. In case of lab-made a-Si:H thin film solar cells with v-shaped LT films, superior optoelectronic performances have been found (V_oc = 0.74 V, J_sc = 15.62 mA/cm², F.F. = 70%, and η = 8.09%). We observed ~ 35% enhancement of the short-circuit current density and ~ 31% enhancement of the conversion efficiency.     

Degradation of phenol using a combination of ultrasonic and UV irradiations at pilot scale operation

In the present work, combination of ultraviolet (UV) irradiations (using 8 W UV tube) with ultrasonic (US) irradiations (rated power 1 kW and frequency of 25 kHz) has been investigated for the degradation of phenol at pilot scale of operation. Different modes of operation viz. UV alone, US alone, UV/US, UV/TiO₂ (photocatalysis), UV/H₂O₂, UV/NaCl, UV/US/TiO₂ (sonophotocatalysis) and H₂O₂ assisted sonophotocatalysis have been investigated with an objective of maximizing the extent of phenol degradation. Effect of presence of hydrogen peroxide and sodium chloride at a concentration of 10 g/l and TiO₂ over a range of 0.5–2.5 g/l has been investigated. It has been observed that 2.0 g/l of TiO₂ is the optimum concentration, beyond which a decrease in the extent of degradation is observed. Maximum extent of degradation of phenol was 37.75% for H₂O₂ assisted photosonocatalysis at pH of 2. The present work is first of its kind to report the use of combined ultrasonic and UV irradiations at pilot scale operation and obtained results should induce some degree of certainty in proposed industrial applications of sonochemical reactors for wastewater treatment.     

Disinfection effect of a continuous-flow ultrasound/ultraviolet baffled reactor at a pilot scale

An ultrasound/ultraviolet (US/UV) baffled reactor was developed to fill the gap in ultraviolet (UV) disinfection associated with disinfection efficiency. According to the previously selected operational condition, a continuous-flow US/UV baffled reactor was continuously operated in a wastewater treatment plant at a pilot scale for nearly three months, and the disinfection influent and effluent were analyzed, including fecal coliforms, Escherichia coli, and fecal streptococci. The US/UV baffled reactor could guarantee a high effluent disinfection performance in terms of fecal coliforms removal even with the fluctuation of the secondary effluent. All the disinfected effluents satisfied the requirement of the “Pollutants Discharge Standard of Municipal Wastewater Treatment Plant in China” (fecal coliforms below 1000 CFU/L for class 1A), and 87% of the tested fecal coliforms concentration in the disinfected effluent was below 100 CFU/L, nearly eliminating all fecal coliforms. Further analysis of the E. coli and fecal streptococci showed the broad disinfection ability and high disinfection efficiency of the US/UV baffled reactor. The flexibility of the specific energy consumption for the disinfection system depends on the water quality.     

Measurement of optical and surface properties of PLZT thin films

Lanthanum-modified lead zirconate titanate (Pb_0.93La_0.07(Zr_0.3Ti_0.7)_0.93O₃, PLZT7/30/70) thin films with and without a seeding layer of PbTiO₃ (PT) were successfully deposited on indium-doped tin oxide (ITO) coated glass substrate via spin coating in conjunction with a sol–gel process, and a top transparent conducting thin film of SnO₂ was also prepared in the same way. The thicknesses of PLZT and PT layers are 0.5 μm and 24 nm, respectively. The retardance of PLZT film was measured by a new heterodyne interferometer and enhanced by application of a seeding layer of PT. The Pockels linear electro-optical coefficient of PLZT film with a PT layer was determined to be 3.17 × 10^?9 m/V when the refractive index is considered as 2.505, which is one order larger than 1.4 × 10^?10 m/V for PLZT12/40/60 doped with Dy reported in the literature. The root-mean-square (rms) roughness of PLZT thin film with a PT layer (R_rms = 6.867 nm) was larger than that of PLZT film (R_rms = 0.799 nm). From the comparisons, the average transmittance of PLZT film with a PT seeding layer was 77.01%, which was a little smaller than that of PLZT film (around 80.75%). Experimental results imply that the PT seeding layer plays a key role in the increase of retardance value, leading to a higher Pockels coefficient.     

Intense 974 nm emission from ErxYb2−xSi2O7 films through efficient energy transfer up-conversion from Er3+ to Yb3+ for Si solar cell

The optical properties of the Er_xYb_2?xSi₂O₇ thin films were investigated by photoluminescence measurements and the intense 974 nm light emission was observed. The 974 nm emission was mainly from the transition ²F_5/2 to ²F_7/2 level of Yb³⁺ upon exploring energy-transfer via up-conversion at Er^{3+ 4}I_13/2 level. Under 972 nm excitation, the lifetime at Er^{3+ 4}I_13/2 level reaches up to 4 ms for film containing 2 at% Er³⁺, while decreases to about 20 μs as the film is pumped by 488 nm. This confirmed that the energy transfer up-conversion process was the dominant transition at Er^{3+ 4}I_13/2 level. This may be of interest to improve the solar cells′ efficiency by placing this film at the rear of cell, converting the near-infrared photons between 1480 nm and 1580 nm to just above the Si bandgap.     

Homogeneous sonophotolysis of food processing industry wastewater: Study of synergistic effects,mineralization and toxicity removal

The mineralization of industrial wastewater coming from food industry using an emerging homogeneous sonophotolytic oxidation process was evaluated as an alternative to or a rapid pretreatment step for conventional anaerobic digestion with the aim of considerably reducing the total treatment time. At the selected operation conditions ([H₂O₂] = 11,750 ppm, pH = 8, amplitude = 50%, pulse length (cycles) = 1), 60% of TOC is removed after 60 min and 98% after 180 min when treating an industrial effluent with 2114 ppm of total organic carbon (TOC). This process removed completely the toxicity generated during storing or due to intermediate compounds.An important synergistic effect between sonolysis and photolysis (H₂O₂/UV) was observed. Thus the sonophotolysis (ultrasound/H₂O₂/UV) technique significantly increases TOC removal when compared with each individual process.Finally, a preliminary economical analysis confirms that the sono-photolysis with H₂O₂ and pretreated water is a profitable system when compared with the same process without using ultrasound waves and with no pretreatment.     

β-NaYF4:Er3+(10%) microprisms for the enhancement of a-Si:H solar cell near-infrared responses

β-NaYF₄:Er³⁺(10%) microprisms, synthesized using a hydrothermal method, were applied to the back of a thin film hydrogenated amorphous silicon (a-Si:H) solar cells to investigate response to sub-band gap near-infrared irradiation. Currents of 0.3 μA and 0.01 μA were measured during single-illumination with 60 mW (80 mW/cm²) 980 nm and 1560 nm diode lasers, respectively, due to frequency upconversion (UC). Under co-excitation by 60 mW 980 nm and 100 mW 1560 nm lasers, a current improvement to 0.54 μA was obtained, resulting from enhancements in red emission. The finding indicates that co-excitation with multiple wavelengths accessible to UC materials is very effective in enhancing the efficiency of solar cells.     

Deposition of device quality amorphous silicon and solar cell from argon dilution of silane

In our present study hydrogenated amorphous silicon (a-Si:H) thin films and solar cells have been prepared in a conventional single chamber rf-PECVD unit from silane–argon mixture by varying radio frequency (rf) power densities from 6 mW/cm² to 50 mW/cm². By optimizing the properties of the intrinsic material we have chosen a material which is deposited at 6 mW/cm² rf power density, 0.2 Torr pressure, 175 ^oC substrate temperature and by 97% argon dilution. For this material minority carriers (holes) diffusion length (L_d) measured in the as deposited state is 180 nm and it degrades by 15% after light soaking. This high L_d value indicates that the material is of device quality. We have fabricated a single junction solar cell having the structure p-a-SiC:H/i-a-Si:H/n-a-Si:H without optimizing the doped layers. This set exhibits a mean open circuit voltage of 0.8 V and conversion efficiency of 7.7%. After light soaking conversion efficiency decreases by 15% which demonstrates that it is possible to deposit device grade material and solar cells from silane–argon mixture.     

Intensification of depolymerization of polyacrylic acid solution using different approaches based on ultrasound and solar irradiation with intensification studies

Depolymerization of polyacrylic acid (PAA) as sodium salt has been investigated using ultrasonic and solar irradiations with process intensification studies based on combination with hydrogen peroxide (H₂O₂) and ozone (O₃). Effect of solar intensity, ozone flow and ultrasonic power dissipation on the extent of viscosity reduction has been investigated for individual treatment approaches. The combined approaches such as US + solar, solar + O₃, solar + H₂O₂, US + H₂O₂ and US + O₃ have been subsequently investigated under optimum conditions and established to be more efficient as compared to individual approaches. Approach based on US (60 W) + solar + H₂O₂ (0.01%) resulted in the maximum extent of viscosity reduction as 98.97% in 35 min whereas operation of solar + H₂O₂ (0.01%), US (60 W), H₂O₂ (0.3%) and solar irradiation resulted in about 98.08%, 90.13%, 8.91% and 90.77% intrinsic viscosity reduction in 60 min respectively. Approach of US (60 W) + solar + ozone (400 mg/h flow rate) resulted in extent of viscosity reduction as 99.47% in 35 min whereas only ozone (400 mg/h flow rate), ozone (400 mg/h flow rate) + US (60 W) and ozone (400 mg/h flow rate) + solar resulted in 69.04%, 98.97% and 98.51% reduction in 60 min, 55 min and 55 min respectively. The chemical identity of the treated polymer using combined approaches was also characterized using FTIR (Fourier transform infrared) spectra and it was established that no significant structural changes were obtained during the treatment. Overall, it can be said that the combination technique based on US and solar irradiations in the presence of hydrogen peroxide is the best approach for the depolymerization of PAA solution.     

Visible luminescence of nanocrystalline AlN:Er thin film by co-deposition of AlN,Er, and SiO2

We report a visible luminescence of Er³⁺ ions in an amorphous-nanocrystalline AlN:Er thin film prepared by co-deposition using AlN, Er, and SiO₂ targets. A PL emission spectrum of Er³⁺ in the AlN:Er film annealed at 750 °C showed a strong bluish green emission of Er³⁺ in the amorphous-nanocrystalline AlN:Er thin film, which is attributed to the intra-4fEr³⁺ transitions of ²H_11/2 → ⁴I_15/2 and ⁴F_7/2 → ⁴I_15/2. It was found that crystallite diameters were between 3 and 5 nm by high-resolution transmission electron microscopy. The occurrence of the strong Er³⁺ emission in the annealed AlN:Er thin film with a mixture of amorphous and nanocrystalline phases may be contributed to an increase in the number of excitation Er³⁺ centers and a presence of oxygen related to Er³⁺ excitation and recombination process in the AlN:Er thin film.     

Ultrasonically enhanced electrochemical oxidation of ibuprofen

A hybrid advanced oxidation process combining sonochemistry (US) and electrochemistry (EC) for the batch scale degradation of ibuprofen was developed. The performance of this hybrid reactor system was evaluated by quantifying on the degradation of ibuprofen under the variation in electrolytes, frequency, applied voltage, ultrasonic power density and temperature in aqueous solutions with a platinum electrode. Among the methods examined (US, EC and US/EC), the hybrid method US/EC resulted 89.32%, 81.85% and 88.7% degradations while using NaOH, H₂SO₄ and deionized water (DI), respectively, with a constant electrical voltages of 30 V, an ultrasound frequency of 1000 kHz, and a power density of 100 W L⁻¹ at 298 K in 1 h. The degradation was established to follow pseudo first order kinetics. In addition, energy consumption and energy efficiencies were also calculated. The probable mechanism for the anodic oxidation of ibuprofen at a platinum electrode was also postulated.     

Comparative study on structural and optical properties of ZnO thin films prepared by PLD using ZnO powder target and ceramic target

Zinc oxide thin films have been obtained in O₂ ambient at a pressure of 1.3 Pa by pulsed laser deposition (PLD) using ZnO powder target and ceramic target. The effect of temperature on structural and optical properties of ZnO thin films was investigated systematically by XRD, SEM, FTIR and PL spectra. The results show that the best structural and optical properties can be achieved for ZnO thin film fabricated at 700 °C using powder target and at 400 °C using ceramic target, respectively. The PL spectrum reveals that the efficiency of UV emission of ZnO thin film fabricated by using powder target is low, and the defect emission of ZnO thin film derived from Zn_i and O_i is high.     

Ultrasound and heat enhanced persulfate oxidation activated with Fe0 aggregate for the decolorization of C.I. Direct Red 23

Effluents from the paper printing and textile industries are often heavily contaminated with azo dyes. Azo dyes are difficult to oxidize biologically. This work investigated the decolorization of an azo dye, C.I. Direct Red 23 (DR23), by persulfate (PS) activated with Fe⁰ aggregates (PS/Fe⁰). Ultrasound (US) and heat were used as enhancement tools in the PS oxidation system. Neither US-activated PS nor thermally activated PS was effective in oxidizing DR23. However, the decolorization was significantly enhanced by PS/Fe⁰ combined with US (PS/Fe⁰/US) or heat (PS/Fe⁰/55 °C). Approximately 95% decolorization of 1 × 10⁻⁴ M DR23 was achieved within 15 min in the PS/Fe⁰/US system at an initial pH of 6.0, PS of 5 × 10⁻³ M, Fe⁰ of 0.5 g/L and US irradiation of 106 W/cm² (60 kHz). Complete decolorization was achieved within 10 min in the Fe⁰/PS/55 °C system. The rate of decolorization doubled when US was introduced in the PS/Fe⁰ system during the treatment of different initial dye concentrations. The dependence of dye and true color (ADMI) depletion on PS concentration has been discussed. DR23 was completely degraded based on the disappearance of aromatic groups of UV–vis spectra and the variation of TOC mineralization. The observed pseudo-first-order decolorization rate was substantially enhanced by increasing temperature. The Arrhenius activation energy for the PS activated with Fe⁰ was estimated as 8.98 kcal/mol, implying that higher temperature is beneficial for the DR23 decolorization. The addition of US into the PS/Fe⁰ system did not incur a substantial increase in electricity, whereas the mineralization of DR23 occurred quickly. Thus, both PS/Fe⁰/US and heated PS/Fe⁰ systems are practically feasible for the effective degradation of the direct azo dye in textile wastewater.     

Electrochemical evaluation of Ta2O5 thin film for all-solid-state switchable mirror glass

We investigated the electrochemical property of Ta₂O₅ thin film for all-solid-state switchable mirror glass. The film was deposited by reactive dc magnetron sputtering in a mixture gas of argon and oxygen. The current density of the film covered WO₃/ITO/glass was decreased with decreasing argon/oxygen ratio and working pressure measured by cyclic voltammetry. The film deposited at argon/oxygen ratio of 4.7 and working pressure of 1.0 Pa had better electrochemical property than that of other deposition condition. Its estimated proton conductivity was 2.1 × 10^? 9 S/cm by conventional ac impedance method. However, the device using the film showed poor optical switching property. The transmittance change of the device at a wavelength of 670 nm was only 16% by applying voltage. On the other hand, the device using the film deposited at working pressure of 0.7 Pa was able to switch its optical switching property from reflective of 0.1% to transparent states of 44% within 15 s. These results indicate that the suitable deposition condition of the Ta₂O₅ thin film existed to be used for all-solid-state switchable mirror glass.     

Synthesis and characterization of Cu2ZnSnS4 thin films by SILAR method

Semiconducting Cu₂ZnSnS₄ (CZTS) material has been receiving a great technological interest in the photovoltaic industry because of its low-cost non-toxic constituents, ideal direct band gap as a absorber layer and high absorption coefficient. CZTS thin films have been successfully deposited onto the fluorine-doped tin oxide/glass (glass/FTO) substrates coated glass substrates using successive ionic layer adsorption and reaction (SILAR) method and investigated for photoelectrochemical conversion (PEC) of light into electricity. The best solar cell sample showed an open-circuit voltage of 390 mV, a short-circuit current density of 636.9 μA/cm², a fill factor of 0.62 and an efficiency of 0.396% under irradiation of 30 mW/cm². Preliminary results obtained for solar cells fabricated with this material are promising.     

Optimization of microcrystalline silicon thin film solar cell isolation processing parameters using ultraviolet laser

This study used ultraviolet laser to perform the microcrystalline silicon thin film solar cell isolation scribing process, and applied the Taguchi method and an L₁₈ orthogonal array to plan the experiment. The isolation scribing materials included ZnO:Al, AZO transparent conductive film with a thickness of 200 nm, microcrystalline silicon thin film at 38% crystallinity and of thickness of 500 nm, and the aluminum back contact layer with a thickness of 300 nm. The main objective was to ensure the success of isolation scribing. After laser scribing isolation, using the minimum scribing line width, the flattest trough bottom, and the minimum processing edge surface bumps as the quality characteristics, this study performed main effect analysis and applied the ANOVA (analysis of variance) theory of the Taguchi method to identify the single quality optimal parameter. It then employed the hierarchical structure of the AHP (analytic hierarchy process) theory to establish the positive contrast matrix. After consistency verification, global weight calculation, and priority sequencing, the optimal multi-attribute parameters were obtained. Finally, the experimental results were verified by a Taguchi confirmation experiment and confidence interval calculation. The minimum scribing line width of AZO (200 nm) was 45.6 μm, the minimum scribing line width of the microcrystalline silicon (at 38% crystallinity) was 50.63 μm and the minimum line width of the aluminum thin film (300 nm) was 30.96 μm. The confirmation experiment results were within the 95% confidence interval, verifying that using ultraviolet laser in the isolation scribing process for microcrystalline silicon thin film solar cell has high reproducibility.     

Third order nonlinear optical properties of ethyltriphenylphosphonium bis(2-thioxo-1,3-dithiole-4,5-dithiolato)aurate (III)

A novel organometallic compound, ethyltriphenylphosphonium bis(2-thioxo-1,3-dithiole-4,5-dithiolato)aurate (III), abbreviated as TPEPADT, was synthesized. The TPEPADT doped poly(methyl methacrylate) (PMMA) thin film with a mass fraction of 1% (1 wt.%) was prepared by using a spin-coating method. The third-order nonlinear optical properties of TPEPADT in acetonitrile solution and TPEPADT-doped PMMA thin film were investigated by using the laser Z-scan technique at the wavelength 1064 nm with laser duration of 20 ps. The linear refractive index of the polymer thin film was also studied. The Z-scan curves revealed that both TPEPADT in acetonitrile solution and the polymer thin film possessed negative nonlinear refraction, exhibiting a self-defocusing effect and nonlinear absorption was negligible under the experimental conditions used. The nonlinear refractive index was calculated to be ?1.9 × 10^?18 m²/W for TPEPADT in acetonitrile solution and ?8.9 × 10^?15 m²/W for the polymer thin film. These results suggest that TPEPADT have potential for the application of all-optical switching devices.     

ArF excimer laser deposition of wide-band gap solid electrolytes for thin film batteries

High quality solid electrolyte thin films was grown by pulsed laser deposition (PLD) using a high photon energy ArF excimer laser. Various amorphous thin films were successfully deposited on glass substrates from oxide targets; such as Li₃PO₄, LiBO₂, Li₂SiO₃, Li₂CO₃, Li₂SO₄, Li₂ZrO₃, LiAlO₂, Li₂WO₄ and Ohara glass ceramics. The morphology, optical property and ionic conductivity of these films were examined by optical microscope, UV–VIS spectroscopy and impedance analysis. Dramatic improvement of the film morphology was observed by using a high photon energy laser, while the broken film with many droplets was obtained by using lower ones. Ionic conductivity of the films was examined by impedance spectroscopy and dc polarization method. For example, an ionic conductivity of a Li₃PO₄ film was 4.6 × 10^? 6 S cm^? 1 at 25 °C with activation energy of 0.57 eV. Electronic conductivity measurements revealed that most of the films were pure lithium ion conductors, while a Li₂WO₄ film was a mixed conductor.     

Degradation of imidacloprid containing wastewaters using ultrasound based treatment strategies

The present work deals with application of sonochemical reactors for the treatment of imidacloprid containing wastewaters either individually or in combination with other advanced oxidation processes. Experiments have been performed using two different configurations of sonochemical reactors viz. ultrasonic horn (20 kHz frequency and rated power of 240 W) and ultrasonic bath equipped with radially vibrating horn (25 kHz frequency and 1 kW rated power). The work also investigates the effect of addition of process intensifying agents such as H₂O₂ and CuO, which can enhance the production of free radicals in the system. The combination studies with advanced oxidation process involve the advanced Fenton process and combination of ultrasound with UV based oxidation. The extent of degradation obtained using combination of US and H₂O₂ at optimum loading of H₂O₂ was found to be 92.7% whereas 96.5% degradation of imidacloprid was achieved using the combination of US and advanced Fenton process. The process involving the combination of US, UV and H₂O₂ was found to be the best treatment approach where complete degradation of imidacloprid was obtained with 79% TOC removal. It has been established that the use of cavitation in combination with different oxidation processes can be effectively used for the treatment of imidacloprid containing wastewater.     

SILAR deposited Bi2S3 thin film towards electrochemical supercapacitor

Bi₂S₃ thin film electrode has been synthesized by simple and low cost successive ionic layer adsorption and reaction (SILAR) method on stainless steel (SS) substrate at room temperature. The formation of interconnected nanoparticles with nanoporous surface morphology has been achieved and which is favourable to the supercapacitor applications. Electrochemical supercapacitive performance of Bi₂S₃ thin film electrode has been performed through cyclic voltammetry, charge-discharge and stability studies in aqueous Na₂SO₄ electrolyte. The Bi₂S₃ thin film electrode exhibits the specific capacitance of 289 Fg⁻¹ at 5 mVs⁻¹ scan rate in 1 M Na₂SO₄ electrolyte.