SiO2/Co3O4核壳催化剂对AP热分解的催化性能研究

采用改良的Stöber法制备粒径约为200 nm的单分散球形SiO₂颗粒,以此为内核,分别通过液相沉淀法和尿素均匀沉淀法制备包覆形式不同的新型SiO₂/Co₃O₄核壳式纳米催化剂。采用X-射线衍射分析(XRD)、透射电子显微镜(TEM)、红外光谱分析(IR)、拉曼光谱分析(Raman)、BET比表面积测试等手段对产物进行表征,利用差式扫描量热仪(DSC)考察SiO₂/Co₃O₄复合物对高氯酸铵(AP)热分解反应的催化作用,探讨不同包覆形式对其催化活性的影响。结果表明,两种方法制备得到的SiO₂/Co₃O₄复合物分别为层包覆和粒子包覆,比表面积大,具有明显的核壳结构,且粒子包覆形式的SiO₂/Co₃O₄对AP热分解反应的催化效果最好,使AP的高温分解温度降低了110 ℃,放热量增加了662 J·g^-1。     

Au和SiO2多壳结构的制备和表征

利用自组装技术和胶体还原化学, 制备出金纳米壳Au@SiO₂以及SiO₂包裹的金纳米壳SiO₂@Au@SiO₂; 去除SiO₂@Au@SiO₂颗粒中的金壳层, 获得含有可移动SiO₂核的空心壳H-SiO₂@M-SiO₂. 结果显示: SiO₂@Au@SiO₂复合颗粒表面光滑, 并保留了金壳的近红外吸收特性; 通过改变复合颗粒外层SiO₂厚度, 可以调节其等离激元共振峰的位置; 王水可以有效地去除SiO₂@Au@SiO₂中的金壳, 相应的等离激元共振峰消失.     

Au和SiO2多壳结构的制备和表征

利用自组装技术和胶体还原化学, 制备出金纳米壳Au@SiO₂以及SiO₂包裹的金纳米壳SiO₂@Au@SiO₂; 去除SiO₂@Au@SiO₂颗粒中的金壳层, 获得含有可移动SiO₂核的空心壳H-SiO₂@M-SiO₂. 结果显示: SiO₂@Au@SiO₂复合颗粒表面光滑, 并保留了金壳的近红外吸收特性; 通过改变复合颗粒外层SiO₂厚度, 可以调节其等离激元共振峰的位置; 王水可以有效地去除SiO₂@Au@SiO₂中的金壳, 相应的等离激元共振峰消失.     

Au/Al2O3纳米复合薄膜的制备和表征

用溶胶-凝胶法制备了Au/Al₂O₃纳米复合薄膜。利用X-射线衍射、X-射线光电子能谱、原子力显微镜以及紫外-可见光谱对薄膜的微观结构、表面形貌及光学性能进行了表征,研究表明:Au/Al₂O₃纳米复合薄膜是由纳米微晶组成的颗粒膜, 复合薄膜均匀、致密、无裂纹,Au以纳米晶核形式镶嵌于Al₂O₃基体中,纳米Au晶核的粒径为23～26nm;复合薄膜在可见光区有较强的吸收,吸收峰位置与烧结温度有关,吸收强度随烧结温度和金添加量增大而增大。     

在一维ZnO表面可控构建Co3Mn1纳米晶及其催化CO氧化性能

利用热分解法制备了结构明确的负载型纳米晶催化剂。在纳米晶成核和生长过程中加入一维ZnO纳米棒作为晶种,调控不同组分的纳米晶在 ZnO纳米棒表面均匀生长,从而获得了结构明确的 MnO/ZnO、Co₃O₄/ZnO、Co₃Mn₁/ZnO催化剂。透射电子显微镜(TEM)与 X 射线粉末衍射(XRD)结果显示,不同组分纳米颗粒都均匀分散在 ZnO 纳米棒表面。相对于 MnO/ZnO 和Co₃O₄/ZnO催化剂,Co₃Mn₁/ZnO催化剂在CO氧化反应中具有最佳的催化性能。在200 L·g_cat^-1·h^-1的气时空速下,Co₃Mn₁/ZnO催化剂起活温度为 50 ℃,其 T100(CO 转化率达到 100% 时的温度)为 200 ℃;利用 X 射线光电子能谱(XPS)对不同催化剂进行了分析,结果显示,Co₃Mn₁/ZnO催化剂的氧空位比MnO/ZnO催化剂提高了30%以上,从而使其具有较高的CO氧化催化性能。更为重要的是,Co₃Mn₁/ZnO复合纳米晶催化剂的活化能(39.4 kJ·mol^-1)远低于其它负载型纳米晶催化剂。     

CuTAPc-Fe3O4纳米复合粒子及其漆酶固定化研究

漆酶的固定化研究对基于漆酶催化的光纤生物传感器具有十分重要的意义. 制备了四氨基酞菁铜(CuTAPc)-Fe₃O₄纳米复合粒子, 并用红外(IR)、场发射扫描电镜(FEG-SEM)、X射线衍射(XRD)、能谱、粒径仪等对其进行了表征. 结果表明形成了以CuTAPc包覆在Fe₃O₄纳米粒子表面的纳米复合粒子, 粒子呈现不规则球形, 且分布均匀, 粒子平均粒径在50 nm左右. 用此纳米复合粒子通过戊二醛交联法固定了漆酶, 固定后的酶比游离酶具有更好的贮存稳定性及操作稳定性. 这为研制高性能的光纤生物传感器打下了较好的基础.     

自生纳米纤维增强SiO2气凝胶的制备及性能研究

采用溶胶-凝胶法和乙醇超临界干燥工艺制备ZrO_X/SiO₂复合气凝胶,再经1200℃高温热处理得到自生纳米纤维增强SiO₂复合气凝胶。利用扫描电子显微镜、透射电子显微镜、X射线衍射、热重和氮气吸附等手段对气凝胶的结构和性能进行了分析,并且测试了样品的压缩强度及真密度。实验结果表明：自生纳米纤维增强SiO₂复合气凝胶具有均匀的多孔网络结构,锆氧纳米纤维是以化学键连接复合的方式无序穿插在气凝胶中,对复合气凝胶的机械强度和隔热性能有明显的改善。经1200℃热处理后的ZrO_X/SiO₂复合气凝胶比表面积为827.22m₂·g^-1,压缩强度为9.68MPa,真密度为0.23g·cm^-3。     

Fe3O4@SiO2@polymer复合粒子的制备及在药物控制释放中的应用

本文通过多步反应制备了一种新型的、多层结构的、多功能的磁性纳米复合粒子, (Fe₃O₄@SiO₂@polymer). 纳米复合粒子内核是磁性Fe₃O₄纳米粒子, SiO₂包裹在Fe₃O₄上能够使其稳定分散和保护其不被腐蚀氧化; 中间层是生物相容的聚天冬氨酸(PAsp)载药层; 最外层是亲水的聚乙二醇(PEG)稳定层. 磁性纳米复合粒子各层都是生物相容的, 利用静电作用将抗癌药物阿霉素(DOX)负载在磁性纳米复合粒子中, 通过PAsp的pH响应调节了DOX的释放速率.     

HA/ZnO/SiO2梯度涂层材料的制备及其体外抗菌活性测试

采用区带电泳法电泳羟基磷灰石（HA）、壳聚糖（CS）、ZnO和SiO₂悬浊液,接着施予反向电场进行电泳沉积从而在钛基材表面获得HA/CS/ZnO/SiO₂复合涂层材料,而后经710℃焙烧2 h后得到HA/ZnO/SiO₂涂层材料（Z1）。同时也仅用电泳沉积法直接制得HA/ZnO/SiO₂涂层材料（E1）作为对比。X射线能谱分析发现Si和Zn两种元素在Z1的径向上均呈现梯度分布,初步说明Z1具有一定的梯度。结合扫描电子显微镜、粉末X射线衍射、傅里叶红外光谱等手段对2种材料进行表征,发现Z1的各种性能较E1更为优异,主要表现在Z1与钛基材表面的结合强度达31.2 MPa,且在HEPES模拟体液中培养14 d后Z1表面碳磷灰石化程度更加完全。另外,抑菌实验发现Z1粉末对大肠杆菌和金黄色葡萄球菌的抑菌率分别为81.7%和89.4%。     

Fe3O4@SiO2@mTiO2介孔多功能纳米复合颗粒的制备及载药能力

以溶剂热法制备氨基功能化的Fe₃O₄纳米颗粒为磁核,结合溶胶-凝胶法和模板法在其表面先后包覆上致密的SiO₂层和介孔TiO₂层,制备了磁性-发光-微波热转换性-介孔结构为一体的多功能核-壳结构纳米复合颗粒,并对其结构、性能及载药能力进行了研究。XRD分析表明:Fe₃O₄表面包覆上了无定形结构的SiO₂和TiO₂。TEM照片表明:所得的纳米复合颗粒具有明显的核壳结构和完美的球形,构成核的Fe₃O₄颗粒的尺寸在40~50 nm之间,Fe₃O₄@SiO₂@mTiO₂核壳结构纳米复合颗粒的尺寸为60~70 nm,壳层厚度约10 nm,并可观察到壳层中清晰的孔状结构。磁性、荧光光谱和微波热转换特性分析表明:该复合颗粒同时具有良好的发光性、磁性和微波热转换特性。N₂气吸附及药物负载率分析表明,该复合颗粒具有较高的比表面积(640 m²·g^-1)和介孔结构(孔径约2.8 nm)并且具有较高的药物负载率。     

Syntheses of MO2 (M=Si, Ce, Sn) nanoparticles by solid-state reactions at ambient temperature

Nano oxides (SiO₂, CeO₂, SnO₂) were successfully synthesized by solid-state reactions at ambient temperature. The nanoparticles were characterized by X-ray powder diffraction, TEM, BET, and TGA-DTA. The SiO₂ particles were also investigated using IR spectra. Effects of calcination on the nanoparticles were studied in this paper. The solid-state reaction technique is a convenient, inexpensive and an effective preparation method of monodisperse oxide nanoparticles in high yield. The mechanisms of the formation of nano materials by solid-state reactions at ambient temperature were primarily investigated.     

Investigation of structural and thermal characteristics of PVDF/ZnO nanocomposites

The structural and thermal behavior of PVDF/ZnO nanocomposites have been investigated by employing scanning electron microscopy (SEM),TEM, DSC, powder X-ray diffraction (XRD), thermally stimulated discharge current (TSDC), and transient current techniques. SEM/TEM observation indicated the homogeneous dispersion of functionalized ZnO nanoparticles throughout PVDF matrix. DSC shows that the crystallinity is influenced by the presence of ZnO nanoparticles in the PVDF matrix because the filler acts as efficient nucleating agent to facilitate PVDF crystallization. DSC results indicated the enhancement of the glass transition temperature (T _g), melting temperature (T _m) and crystallization temperature (T _c) of nanocomposites compared to pristine PVDF. XRD shows that the full-width at half maximum decreases with increasing ZnO content, which is attributed to the improvement in crystallinity. The incorporation of ZnO nanoparticles influences the modification of polarization process in PVDF as observed by means of TSDC and transient current study.     

Solvent-Free Synthesis of ZnO Nanoparticles by a Simple Thermal Decomposition Method

This paper reports on a novel processing route for producing ZnO nanoparticles by solid-state thermal decomposition of zinc(II) acetate nanostructures obtained by the sublimation of zinc(II) acetate powder. The sublimation process of the Zn(OAc)₂ powder was carried out in the temperature 150 °C for 2 h. In addition, nanoparticles of ZnO were obtained by solid-state thermal decomposition of the synthesized Zn(OAc)₂ nanostructures. The synthesized products were characterized by X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy, photoluminescence spectroscopy, and energy dispersive X-ray spectroscopy. The sublimation process of the Zn(OAc)₂ powder was carried out within the range of 150–180 °C. The XRD studies indicated the production of pure hexagonal ZnO nanoparticles after thermal decomposition.     

ZnO/In2O3复合空心球的制备及其光电催化葡萄糖降解性能

通过葡萄糖协助的水热以及随后的退火处理两步法成功制备了系列ZnO/In₂O₃复合空心球. X射线衍射谱(XRD)表明, 经500 ℃退火制得的ZnO/In₂O₃复合空心球中ZnO以非晶态存在, 但是随着退火温度的提高, 其逐渐转变为纤锌矿结构. 场发射扫描电子显微镜(FE-SEM)和透射显微镜(TEM)结果表明, ZnO/In₂O₃复合材料具有空心球结构, 复合纳米颗粒之间结合紧密. 将ZnO/In₂O₃复合空心球组装成薄膜光电极, 研究了其光电催化降解葡萄糖的性能. 结果表明, 700 ℃退火处理的ZnO/In₂O₃复合空心球薄膜电极可产生最高的光致电流密度. 通过光致发光光谱(PL)发现, 与ZnO或In₂O₃空心球相比, ZnO/In₂O₃复合空心球的发光强度猝灭效果明显. 这是由于复合材料中晶界处产生的p-n结电场, 降低了光生电子-空穴对的复合几率, 从而使更多的光生电子可迁移到电极表面.     

Parameters controlling the photocatalytic performance of ZnO/Hombikat TiO2 composites

Commercial TiO₂ (Hombikat, UV-100) was impregnated with different loadings of zinc nitrate solution and subsequently calcined at different temperatures in order to obtain a stable homogeneous solid composite of ZnO/TiO₂. The prepared samples were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HR-TEM), UV-vis and Raman spectroscopy, inductively coupled plasma mass spectroscopy (ICP), X-ray photoelectron spectroscopy (XPS) as well as N₂ adsorption and desorption measurements. Results show that ZnO was incorporated within the TiO₂ crystals and did not form a separate bulky phase or metallic zinc. Moreover, the calcination temperature dramatically modifies the texture properties of the prepared samples compared with original Hombikat TiO₂. The photocatalytic performance of the prepared samples was evaluated by monitoring the degradation of methyl orange dye under black light illumination. Three main parameters were studied; ZnO loading, surface area and initial pH of the methyl orange solution. The variation in ZnO loading appears to have less influence on the catalytic activity than either the surface area or the pH.     

Preparation and properties of amorphous titania-coated zinc oxide nanoparticles

Amorphous TiO₂-coated ZnO nanoparticles were prepared by the solvothermal synthesis of ZnO nanoparticles in ethanol and the followed by sol-gel coating of TiO₂ nanolayer. The analyses of X-ray diffraction (XRD) and transmission electron microscopy (TEM) revealed that the resultant ZnO nanoparticles were hexagonal with a wurtzite structure and a mean diameter of about 60 nm. Also, after TiO₂ coating, the TEM images clearly indicated the darker ZnO nanoparticles being surrounded by the lighter amorphous TiO₂ layers. The zeta potential analysis revealed the pH dependence of zeta potentials for ZnO nanoparticles shifted completely to that for TiO₂ nanoparticles after TiO₂ coating, confirming the formation of core-shell structure and suggesting the coating of TiO₂ was achieved via the adhesion of the hydrolyzed species Ti-O⁻ to the positively charged surface of ZnO nanoparticles. Furthermore, the analyses of Fourier transform infrared (FTIR) and Raman spectra were also conducted to confirm that amorphous TiO₂ were indeed coated on the surface of ZnO nanoparticles. In addition, the analyses of ultraviolet-visible (UV-VIS) and photoluminescence (PL) spectra revealed that the absorbance of amorphous TiO₂-coated ZnO nanoparticles at 375 nm gradually decreased with an increase in the Ti/Zn molar ratio and the time for TiO₂ coating, and the emission intensity of ZnO cores could be significantly enhanced by the amorphous TiO₂ shell.     

NiTiO<Subscript>3</Subscript> nanoparticles encapsulated with SiO<Subscript>2</Subscript> prepared by sol–gel method

NiTiO₃ (NTO) nanoparticles encapsulated with SiO₂ were prepared by the sol–gel method resulting on core-shell structure. Changes on isoelectric point as a function of silica were evaluated by means of zeta potential. The NTO nanoparticles heat treated at 600°C were characterized by X-ray diffraction, transmission electron microscopy (TEM) and energy dispersive X-ray analysis. TEM observations showed that the mean size of NTO is in the range of 2.5–42.5 nm while the thickness of SiO₂ shell attained 1.5–3.5 nm approximately.     

Synthesis of Mn3O4 nanoparticles by thermal decomposition of a [bis(salicylidiminato)manganese(II)] complex

The present investigation reports on the novel synthesis of Mn₃O₄ nanoparticles using thermal decomposition and their physicochemical characterization. The Mn₃O₄ nanoparticle powder has been prepared using [bis(salicylidiminato)manganese(II)] as a precursor. The effect of oleyl amine and triphenylphosphine on the particle morphology has been investigated. Transmission electron microscopy (TEM) analysis demonstrated Mn₃O₄ nanoparticles with an average diameter of about 25 nm. The structural study by X-ray diffraction (XRD) indicates that these nanoparticles have a pure tetragonal phase. The phase pure samples were characterized using X-ray photoelectron spectroscopy (XPS) for both Mn 2p and Mn 3s levels. The values of binding energies are consistent with related values reported in the literature.     

具有双亲特性的水相哑铃型SiO2纳米粒子的制备

以纳米SiO2水溶胶为原料,3?氨丙基三乙氧基硅烷(APTES)和3?氯丙基三乙氧基硅烷(CPTES)为改性剂,在水基环境下分别对SiO2纳米粒子进行改性,得到了具有亲水特性的APTES改性SiO2粒子和具有亲油特性的CPTES改性SiO2粒子水溶胶。2种粒子按不同比例混合,利用接枝在SiO2粒子表面氨基和氯丙基的取代反应,使得2种具有亲水/亲油特性的改性SiO2纳米粒子偶联,制备了粒径为40~50 nm的哑铃型SiO2纳米粒子。并通过透射电镜(TEM)、傅里叶变换红外光谱(FT?IR)、X射线光电子能谱(XPS)以及动态光散射(DLS)等方法对其进行了系统表征。结果表明,2种粒子成功偶联形成了具有哑铃型结构的水相SiO2纳米粒子,该粒子两面具有不同的亲水性,粒径近似等于APTES改性SiO2粒子和CPTES改性SiO2粒子的粒径之和。     

Nanoflower-like composites of ZnO/SiO2 synthesized using bamboo leaves ash as reusable photocatalyst

In this study, the synthesis of ZnO/SiO₂ nanocomposites using bamboo leaf ash (BLA) and tested their photocatalytic activity for rhodamine B decolorization have been conducted. The nanocomposites were prepared by the sol–gel reaction of zinc acetate dihydrate, which was used as a zinc oxide precursor, with silica gel obtained from the caustic extraction of BLA. The effect of the Zn content (5, 10, and 20 wt%) on the physicochemical characteristics and photocatalytic activity of the nanocomposites was investigated. The results of X-ray diffraction, scanning electron microscopy, gas sorption, and transmission electron microscopy characterization confirmed the mesoporous structure of the composites containing nanoflower-like ZnO (wurtzite) nanoparticles of 10–30 nm in size dispersed on the silica support. Further, the nanocomposites were confirmed to be composed of ZnO/SiO₂ by X-ray photoelectron spectroscopy analysis. Meanwhile, diffuse-reflectance UV–visible spectrophotometry analysis of the nanocomposites revealed band gap energies of 3.38–3.39 eV. Of the tested nanocomposites, that containing 10 wt% Zn exhibited the highest decolorization efficiency (99%) and fastest decolorization rate. In addition, the degradation efficiencies were not reduced significantly after five repeated runs, demonstrating the reusability of the nanocomposite catalysts. Therefore, the ZnO/SiO₂ nanocomposite obtained from BLA is a promising reusable photocatalyst for the degradation of dye-polluted water.