X射线W/B4C宽带多层膜的优化设计和制备

介绍了X射线宽带多层膜材料W和B4C的选定方法,依据伯宁(BERNING)公式确定出了在0.154 nm处X射线宽带多层膜的最佳膜对数。引入适当的评价函数,利用具有全局寻优特性且效率较高的遗传算法,在波长0.154 nm处优化设计出了掠入射角(θ)0.5°~0.9°范围内反射率值达到40%的宽角度宽带多层膜。宽带多层膜反射镜采用磁控溅射方法制备,并用X射线衍射仪对样品进行了检测,结果表明在掠入射角(2θ)1.0°~1.8°之间的相对反射率光谱曲线比较平坦。     

磁控溅射制备横向梯度分布的Mo/Si周期多层膜

 采用磁控溅射方法在Si基板上镀制了横向梯度分布的Mo/Si周期多层膜。以X射线掠入射反射测量了横向梯度多层膜的膜系结构,在基板65 mm长度范围内,多层膜周期从8.21 nm线性减小到6.57 nm,周期梯度为0.03 nm/mm。国家同步辐射实验室反射率计的反射率测试结果表明：该横向梯度分布周期多层膜上不同位置,能反射在13.3~15.9 nm波段范围内不同波长的极紫外光,反射率为60%~65%。     

Residual stress and Curie temperature of Fe-N thin films prepared by dc magnetron sputtering at elevated temperature

Fe-N thin films were prepared by dc magnetron sputtering at elevated temperature of 80 °C. The residual stress of the thin film was characterized by means of grazing incidence X-ray diffraction method. The effect of magnetron sputtering parameter on residual stress was investigated. The results indicate that the nitrogen content in working gas has great effects on the residual stress in the Fe-N thin film, and the residual stress increases firstly and then decreases with the increasing of nitrogen content in working gas. Curie temperature measurement shows that tensile residual stress enhances the ferromagnetic-paramagnetic transition temperature of Fe-N thin films under the condition of same phase composition.     

小型掠入射式近边X射线吸收谱仪的设计

近边X射线吸收精细结构(NEXAFS)谱包含了吸收原子的局域结构信息,由于其适用范围广,灵敏度高,已经成为研究物质结构的重要手段之一。为了研究有机物的碳1s NEXAFS谱,本文基于气体激光等离子体X射线光源,采用具有平场特性的凹面变线距光栅作为分光元件,面阵CCD作为光谱探测器,设计了一台小型掠入射式近边X射线吸收谱仪。通过优化光栅和CCD的装配方案,得到了入射角88.6°的装配参数。利用光线追迹法分析了谱仪的分辨率,该谱仪工作波段2~5 nm,在4.4 nm处分辨率可达666。通过分析各结构参量误差对谱线半高宽的影响发现,半高宽对入射角的误差最为敏感,优化的装配方案可以实现入射角的高精度调节。利用氮气等离子体光谱测试了光谱仪的性能,结果显示分辨率达到设计指标。     

磁控溅射材料沉积速率的定标方法的研究

介绍了一种利用磁控溅射制备多层膜速率的定标方法。用高精度磁控溅射镀膜设备在同一块基片上先后镀制了两种周期的多层膜,用X射线衍射仪对其进行掠入射衍射测量,测量数据经线性拟合,可同时求得两种多层膜的周期,进而得到镀膜速率。与常用的定标方法相比,该方法不仅可以得到与常用定标方法相同的实验结果,而且提高了工作效率。     

Sputtered atom transport processes

It is noted that the transport of sputtered atoms can be described in terms of three pressure regimes: low pressure, where no collisions occur during the trajectory of the atom; intermediate pressure, where the atom undergoes perhaps several collisions but does not completely thermalize; and high pressure, where the sputtered atom effectively stops and begins a density-gradient-driven conventional gas-phase diffusion process. The intermediate region is the most complicated to model, given the dependence of the energy on the collision cross-section, the various distributions in energy and angle of the sputtered atoms, and the extended nature of most sputtering sources. Experimental studies reported here have measured the transport probability by observing the distribution of atoms around a chamber following sputtering. The transport is found to be quite dependent on the mass of both the sputtered atom and the background gas, as well as the particle density and geometry of the vacuum system. A strong effect of sputtered-atom-induced gas rarefaction has also been observed. This results in power-dependent transport of sputtered atoms, and as a result may also lead to power-dependent compositional variation in alloy depositions. The general result is that high discharge powers tend to correlate with lower power operation at a significantly lower operating pressure than had been assumed     

4.48 nm正入射软X射线激光用Cr/C多层膜高反射镜的研制

针对4.48nm类镍钽软X射线激光及其应用实验,设计制备了工作于这一波长的近正入射多层膜高反射镜。选择Cr/C为制备4.48nm高反射多层膜的材料对,通过优化设计,确定了多层膜的周期、周期数以及两种材料的厚度比。模拟了多层膜非理想界面对高反射多层膜性能的影响。采用直流磁控溅射方法在超光滑硅基片上实现了200周期Cr/C多层膜高反射镜的制备。利用X射线衍射仪测量了多层膜结构,在德国BessyⅡ同步辐射上测量了在工作波长处多层膜反射率,测量的峰值反射率达7.5%。对衍射仪测量的掠入射反射曲线和同步辐射测量的反射率曲线分别进行拟合,得到的粗糙度和厚度比的结果相近。测试结果表明,所制备的Cr/C多层膜样品结构良好,在指定工作波长处有较高的反射峰,达到了设计要求。     

基于模拟退火算法的宽角度X射线超反射镜设计研究

应用于硬X射线波段的宽带多层膜光学元件———宽角度X射线超反射镜的设计可以归结为一个连续变量的多维多极值的全局优化问题。缺少一种有效的全局优化方法是阻碍解决这一难题的一个关键。模拟退火算法是一种简单而且通用的全局优化算法。结合光学多层膜的设计原理提出了利用模拟退火算法来进行宽角度X射线超反射镜设计的新方法。结合已有的方法选择了W和C作为膜层的膜对材料,设计出Cu的Kα线处角度范围0.9°~1.1°反射率达到20%的宽角度X射线超反射镜。并在此基础上采用改进的自适应模拟退火算法实现了Cu的Kα线处宽角度X射线超反射镜的理想设计结果。设计结果表明了模拟退火算法在多层膜最优化设计领域的正确性和有效性。     

连续碳纤维增强碳化硅的辐照效应

连续碳纤维增强碳化硅材料除了具有碳化硅材料固有的低中子活化性能,低衰变热性能和低氚渗透性能等优点以外,还具有密度低、线性膨胀系数小、高比强度、高比模量、耐高温、抗氧化、抗蠕变、抗热震、耐化学腐蚀、耐盐雾、优良的电磁波吸收特性等一系列优异性能,是各类核工程重要的潜在候选材料。在核聚变工程应用领域,连续碳纤维增强碳化硅材料作为第一壁材料不可避免地会受到各种辐射粒子的影响。研究清楚这些辐射粒子对它的辐照效应对其在核工程领域的安全使用至关重要。采用蒙特卡罗方法与分子动力学方法进行模拟计算,研究了氕、氘、氚和氦四种粒子对连续碳纤维增强碳化硅的辐照效应。SRIM和LAMMPS计算结果表明:当入射原子能量为100 eV,连续碳纤维增强碳化硅中碳的浓度在80%~85%时,氕、氘、氚和氦原子的溅射率存在最小值;入射粒子的种类对溅射率的影响显著,氦原子的溅射率大于氘原子和氚原子,而氘原子和氚原子的溅射率相差不大但均显著大于氕原子;溅射率随入射能量的增加先迅速增加后逐渐减小,氕、氘、氚和氦原子入射能量分别在200,400,600和800 eV时存在溅射率最大值;当氦原子入射能量为100 eV时,溅射率随入射角度的增加而逐渐减少。这些结果对连续碳纤维增强碳化硅材料在核工程上的应用具有一定的参考意义。Continuous carbon fiber reinforced silicon carbide material has the low neutron activation, low decay heat performance and tritium permeability, which are inherent performance of silicon carbide materials. It also has other advantages such as low density, small linear expansion coefficient, specific strength and specific modulus, high temperature resistance, oxidation resistance, creep resistance, thermal shock, resistance to chemical corrosion, salt fog resistance, excellent electromagnetic wave absorption properties, etc. It is an important potential candidate material in various field of nuclear engineering. In the field of nuclear fusion engineering applications, continuous carbon fiber reinforced silicon carbide as the first wall material will inevitably be bombarded by a variety of radiation particles. The radiation effect is critical to its safe use in nuclear engineering. The Monte Carlo method and the molecular dynamics method were used to study the radiation effect of protium, deuterium, tritium and helium on continuous carbon fiber reinforced silicon carbide. The SRIM and LAMMPS simulation results show that when the incident energy is 100 eV and the concentration of carbon in the continuous carbon fiber reinforced silicon carbide is about 80% ~ 85%, the sputtering yield of protium, deuterium, tritium and helium atoms have the minimum values. The kind of incident particle has a significant effect on the sputtering yield. The sputtering yield of helium atoms is larger than that of tritium atoms and deuterium atoms. There is not much difference between the sputtering yield of deuterium atoms and tritium atoms, and both the sputtering yield of deuterium atoms and tritium atoms are larger than that of protium atoms. The sputtering yield initially increases rapidly with the increase of the incident energy and then decreases gradually. The incident energy of the protium, deuterium, tritium and helium atoms has the maximum value of the sputtering yield at 200, 400, 600 and 800 eV, respectively. When the incident energy of helium atoms is 100 eV, the sputtering yield decreases while the increase of the incident angle. These results can provide a certain reference for the application of continuous carbon fiber reinforced silicon carbide materials in nuclear engineering.     

Synthesis of Fe:Al2O3 thin films by ion beam sputtering: Interface effect

Fe:Al₂O₃ thin films containing 20 at.% iron were deposited at room temperature on different substrates by using ion beam sputtering. Conversion electron Mössbauer spectroscopy, grazing angle X-ray diffraction and transmission electron microscopy have allowed localization of the ferrous ions at the film-substrate interfaces.     

Performance of a polarizer using synthetic mica crystal in the 12-25 nm wavelength range

To develop polarizer functioning in the extreme ultraviolet (EUV) and soft X-ray region, the polar- ization performance of synthetic mica has been investigated theoretically with a simulation code using Fresnel equations and optical constants from the Henke database. The reflectance of synthetic mica crystal for s and p polarization was measured to investigate its polarization performance in a home-made synchrotron radiation soft X-ray polarimeter at beamline 3W1B, Beijing Synchrotron Radiation Facility (BSRF). The reflectivity of the synthetic mica crystal at an angle of grazing incidence of 48° was obtained from the experimental data, which is about 4.8x10<'-3> at 25 nm and 6.0×10<'-4> at 12 nm, and the linear polarizance of the X-ray reflected by the synthetic mica crystal that we measured using an analyzer-rotating method increases from 80% to 96.6% in this EUV region, while higher than 98.2% in the simulation. The result indicates that this synthetic mica crystal works as a practical polarizer in this EUV region of 12-25 nm, and also in an extensive wavelength region higher than 25 nm.     

激光等离子体光源软X射线反射率计

介绍了所研制的激光等离子体光源软X射线反射率计,该反射率计由激光等离子体光源、掠入射光栅单色仪、样品室、真空系统、样品台、光电探测系统和计算机控制系统组成,工作波段8～30 nm,测量样品的最大尺寸为130 mm×120 mm×120 mm(长×宽×高),可以利用这台反射率计对软X射线波段光栅、滤光片和多层膜反射镜等光学元件进行测量和评估。为检验反射率计的性能指标,利用该反射率计对本室研制的软X射线多层膜反射镜的反射率进行了测量,测量结果与理论计算结果符合较好,反射率测量重复性为±0.6%。     

Fresnel diffraction mirror for an atomic wave

We have experimentally demonstrated a material-independent mirror for atomic waves that uses the Fresnel diffraction at an array of parallel ridges. He* (2 (3)S(1)) and Ne* (1s(3)) atomic waves were reflected coherently on a silicon plate with a microfabricated grating structure, consisting of narrow wall-like ridges. We measured the reflectivity at grazing incidence as a function of the incident velocity and angle. Our data show that the reflectivity on this type of mirror depends only on the distance between the ridges, the wavelength, and the incident angle, but is insensitive to the material of the grating structure. The reflectivity is observed to increase by 2 orders of magnitude, compared to that of a flat polished silicon surface, where the reflection is caused by the attractive surface potential. For He* atoms, the measured reflectivity exceeds 10% for normal incident velocities below about 25 cm/s.     

Co/C and W/Si multilayers deposited by ion-beam sputtering for the soft X-ray range

We deposited Co/C multilayer mirrors for a wavelength of 4.77 nm and W/Si multilayer mirrors for a wavelength of 1.77 nm by use of ion-beam sputtering. The small-angle diffraction spectrum was used to analyze the structure of the multilayers. With a combination of the experimental diffraction spectra and Apeles’ theory for calculation of the interfacial roughnesses of the multilayers, the interfacial roughnesses of Co/C and W/Si are 0.80 nm and 0.60 nm, respectively, which are lower than that of the substrate. The reflectivity of the Co/C multilayer is measured to be about 20% and that of the W/Si multilayer about 1% at the grazing incidence angle of about 12°. Received: 30 May 2000 / Accepted: 1 August 2000 / Published online: 11 February 2002     

高电荷态离子与SiO2表面相互作用的研究

高电荷态离子(Pbq ,Arq )由兰州近代物理研究所的ECR实验平台所产生,轰击非晶态SiO2表面.用微通道板测量溅射粒子产额的角分布.用公式拟合实验溅射角分布得到了较好的结果,并给出了初步的理论解释.由此得出了高电荷态离子与SiO2表面作用的微分溅射截面.实验结果表明高电荷态离子能够增加动能溅射;同时高电荷态离子入射能够引起势能溅射.在大角度入射时,溅射产额主要是由碰撞引起的;在小角入射时势能溅射所占比重会增大.     

Angular distribution of copper atoms sputtered with energetic ions

Measurements of the angular distribution of copper atoms which are sputtered by noble gas ions within the energy range between 0.1 and 1 MeV have been carried out for different angles of ion incidence. The hemisphere over the target surface could be studied with a microphotometer inside the sputtering chamber and the distributions can be plotted in tri-dimensional diagrams. The results are in principle similar to those obtained at lower energies. The angle of maximum emission varies with ion energy and with the angle of incidence and can be related to the sputtering yield.     

30.4 nm波长SiC/Mg多层膜反射镜

波长30.4 nm的He-II谱线是极紫外天文观测中最重要的谱线之一,空间极紫外太阳观测光学系统需要采用多层膜作为反射元件。为此研究了SiC/Mg、B4C/Mg、C/Mg、C/Al、Mo/Si、B4C/Si、SiC/Si、C/Si、Sc/Si等材料组合的多层膜在该波长处的反射性能。基于反射率最大与多层膜带宽最小的设计优化原则,选取了SiC/Mg作为膜系材料。采用直流磁控溅射技术制备了SiC/Mg多层膜,用X射线衍射仪测量了多层膜的周期厚度,用国家同步辐射计量站的反射率计测量了多层膜的反射率,在入射角12°时,实测30.4 nm处的反射率为38.0%。     

50~110 nm波段高反射率多层膜的设计与制备

阐述了50~110 nm强吸收波段亚四分之一波长多层膜的设计方法.这种膜系是由强吸收材料叠加而成，每层膜光学厚度小于四分之一个波长.与常规周期多层膜相比，这种膜系更适用于提高强吸收波段的反射率.利用该方法设计了50 nm处高反射多层膜，并以此为初始条件通过Levenberg-Marquart优化方法完成了50~110 nm强吸收波段宽带高反射率Si/W/Co多层膜的设计，其平均反射率达到45%.采用直流磁控溅射方法制备了Si/W/Co多层膜,用X射线衍射仪(XRD)对膜层结构进行了测试，测试结果表明制作出的多层膜结构与设计结构基本相符.     

三元合金Cu76Ni15Sn9的离子溅射研究

在２７ｋｅＶ Ａｒ⁺离子轰击时,用收集膜技术结合俄歇谱仪（ＡＥＳ）,研究了三元合金Cu₇₆Ni₁₅Sn₉系统的择优溅射行为。同时使用扫描电子显微镜（ＳＥＭ）与电子探针微分析（ＥＰＭＡ）．观察了靶点表面形貌变化并测定了形貌特征微区的合金组份原子的相对百分浓度。结果表明,Ｃｕ原子较Ｎｉ原子、Ｎｉ原子较Ｓｎ原子,在所测定范围（０─６０°）内择优发射。最后讨论了靶点表面形貌特征和“元素局域富集”现象对择优溅射过程的影响。 关键词：     

Mo/Si aperiodic multilayer broadband reflective mirror for 12.5-28.5-nm wavelength range

Aperiodic molybdenum/silicon (Mo/Si) multilayer designed as a broadband reflective mirror with mean reflectivity of 10% over a wide wavelength range of 12.5-28.5 nm at incidence angle of 5° is developed using a numerical optimized method. The multilayer is prepared using direct current magnetron sputtering technology. The reflectivity is measured using synchrotron radiation. The measured mean reflectivity is 7.0% in the design wavelength range of 12.5-28.5 nm. This multilayer broadband reflective mirror can be used in extreme ultraviolet measurements and will greatly simplify the experimental arrangements.