苯巴比妥分子印迹电化学传感器的制备及其性能研究

以马来松香丙烯酸乙二醇酯为交联剂,甲基丙烯酸为功能单体,偶氮二异丁腈为引发剂,苯巴比妥为模板分子,在玻碳电极表面热聚合了一种用于测定苯巴比妥的印迹聚合物传感膜。探索了传感器的最佳实验条件,并在此实验条件下,采用循环伏安法、差分脉冲伏安法及电化学交流阻抗法研究了传感器对苯巴比妥的响应特性。实验结果表明,传感器的峰电流响应值与苯巴比妥的浓度在3.0×10-6~1.0×10-4mol/L范围内呈现良好的线性关系(线性相关系数R=0.9976),检出限(S/N=3)为5.4×10-7mol/L。用此印迹传感器对苯巴比妥片中苯巴比妥的含量进行了测定,回收率在91.5%~107.5%。     

基于电聚合的苯巴比妥分子印迹电化学传感器的制备及其应用研究

以马来松香丙烯酸乙二醇酯(EGMRA)为交联剂,甲基丙烯酸为功能单体,在玻碳电极表面电聚合了一种对苯巴比妥分子具有专一性识别的聚合膜。在最佳实验条件下,采用循环伏安法(CV)、差分脉冲伏安法(DPV)及电化学交流阻抗法(EIS)对印迹传感器的性能进行研究。实验结果表明:该印迹传感器对苯巴比妥具有快速响应、专一性识别和高灵敏度的特点,且苯巴比妥的浓度在8.0×10-7~1.0×10-4mol/L范围内与DPV电流信号呈良好的线性关系,相关系数(r)为0.998 3。检出限(S/N=3)为5.4×10-8mol/L。将此印迹传感器应用于实际样品中苯巴比妥的检测,加标回收率为95.7%~105.0%。     

盐酸环丙沙星分子印迹电化学传感器

本文将电化学合成与分子印迹技术相结合,采用循环伏安法在石墨电极表面,形成盐酸环丙沙星(CPX)分子印迹聚吡咯薄膜,制备了CPX分子印迹传感器。实验对传感器的制备条件进行了优化,用铁氰化钾作为活性电子探针,采用方波伏安法研究了传感器性能。结果表明,在1×10~(-8)~1×10~(-4)mol/L范围内,峰电流与CPX浓度负对数呈良好的线性关系,检出限(S/N=3)为3.5×10~(-9)mol/L。传感器对模板分子CPX选择性强,重现性和稳定性好,置于室温下15d峰电流强度无明显变化。     

基于石墨烯的毒死蜱分子印迹电化学传感器的制备及对毒死蜱的测定

利用分子印迹技术,以马来松香丙烯酸乙二醇酯为交联剂,使用自由基热聚合法在石墨烯修饰的玻碳电极表面合成毒死蜱( CPF)分子印迹聚合膜,制得了CPF分子印迹电化学传感器。采用循环伏安法、线性扫描伏安法和电化学交流阻抗法等,考察了此CPF分子印迹膜的电化学性能。在最佳检测条件下,传感器的峰电流与CPF浓度在2.0×10-7~1.0×10-5mol/L范围内呈线性关系,线性方程为Ip(μA)=-7.1834-0.2424C (μmol/L),相关系数r2=0.9959,检出限为6.7×10-8 mol/L(S/N=3)。构建了CPF分子印迹电化学传感器的动力学吸附模型,测得印迹传感器的印迹因子β=2.59,结合速率常数k=12.2324 s。传感器表现出良好的重现性和稳定性,并成功用于实际水样和蔬菜样品中CPF的测定,加标回收率为94.1%~101.4%。     

水胺硫磷分子印迹传感器的制备与应用

在磷酸盐缓冲溶液(PBS)中,以邻苯二胺(o-PD)和没食子酸(GA)为功能单体,水胺硫磷(ICP)为模板分子,采用电位循环扫描法在玻碳电极(GCE)表面进行电聚合,形成绝缘性的分子印迹膜,通过电化学阻抗谱(EIS)和循环伏安法(CV)对分子印迹膜进行表征.在最佳实验条件下,以铁氰化钾[ K3Fe(CN)6]为探针,用差分脉冲伏安法( DPV)对ICP进行定量分析.该传感器在2.00×10 -7～2.00×10-4 mol/L范围内,传感器的响应信号与ICP的浓度呈良好的线性关系,检测限为6.06×10-s mol/L( S/N=3).将其用于蔬果等实际样品中ICP的测定,回收率为95.6％～104.0％.     

基于纳米氧化铜修饰的异戊巴比妥的新型电化学传感器的制备与应用

在纳米氧化铜修饰的玻碳电极表面电聚合一种能够快速检测尿液中异戊巴比妥(AMB)的分子印迹敏感膜,研究了该敏感膜的最佳成膜条件及最佳工作条件.通过扫描电子显微镜(SEM)、循环伏安(CV)和电化学交流阻抗法(EIS)研究了印迹膜的表面形貌及性能.电化学实验结果表明,纳米氧化铜能提高传感器对AMB的灵敏度.在最佳实验条件下,铁氰化钾分子探针的差分脉冲伏安(DPV)峰电流响应值与AMB的浓度在1.0×10-7~1.4×10-4mol/L范围内呈现良好的线性关系(线性相关系数R=0.9966);检出限为2.1×10-9mol/L(S/N=3).此印迹传感器可用于尿液中AMB的检测,加标回收率为94.00%~104.67%.     

碳纳米管修饰电极分子印迹传感器的制备及其对氧乐果的测定

以氧乐果为模板分子,邻苯二胺为功能单体,在碳纳米管修饰的玻碳电极表面通过电聚合方法制成氧乐果分子印迹聚合物膜,用无水乙醇洗脱后制备出对氧乐果有特异响应的电化学传感器。通过循环伏安法和电化学阻抗法对分子印迹传感器的电化学性能进行表征。以K_3Fe(CN)_6为探针,采用差分脉冲伏安法研究了该分子印迹传感器的分析性能,建立了氧乐果的间接测定方法。结果表明,K_3Fe(CN)_6的相对峰电流与氧乐果浓度在1.0×10~(-7)~2.0×10~(-6)mol/L范围内呈良好的线性关系,检出限为3.6×10~(-8)mol/L。     

磁性石墨烯修饰辛基酚印迹传感器制备及应用研究

以辛基酚(4-OP)为模板分子,多巴胺为功能单体,采用电聚合技术在磁性石墨烯修饰碳电极表面制备对辛基酚具有高选择性与灵敏性的印迹电化学传感器。采用循环伏安法(CV)和差分脉冲伏安法(DPV)对此印迹传感器的电化学性能进行详细表征;采用扫描电子显微技术对修饰电极的形貌进行表征。结果表明,此印迹电化学传感器对辛基酚具有良好的特异识别性能。采用 DPV 法考察了孵化时间和洗脱溶剂对印迹传感器性能影响,结果表明,最佳孵化时间为14 min。此印迹电化学传感器的响应电流(△IR )与辛基酚在5.0×10-6~5.0×10-9 mol/ L 范围内浓度的负对数(-lgC)呈良好的线性关系,线性方程为△IR ( mA)=-0.25lgC(mol/ L)+2.35,检出限为3.64×10-10 mol/ L (S/ N=3)。此印迹电化学传感器对辛基酚具有良好的选择性和灵敏性,成功用于实际水样中辛基酚的检测,回收率为96.0%~104.0%。     

纳米氧化铜修饰的苯巴比妥分子印迹传感器的制备及其电化学性能

为了改善分子印迹传感器的灵敏度,在四丁基高氯酸铵的支持电解质溶液中,以甲基丙烯酸为功能单体,马来松香丙烯酸乙二醇酯为交联剂在纳米氧化铜修饰过的玻碳电极上电聚合了一种苯巴比妥(PB)识别性能的分子印迹传感膜.采用循环伏安(CV)法、差分脉冲伏安(DPV)法及交流阻抗(EIS)法对这种纳米氧化铜修饰过的印迹及非印迹电极的电化学性能进行了研究,结果显示纳米氧化铜修饰过的印迹及非印迹电极的电化学性能完全不同.X射线衍射(XRD)证实纳米粒子为氧化铜.采用扫描电镜(SEM)对纳米氧化铜修饰过的印迹传感器的形貌进行分析,发现纳米氧化铜分散在电极表面,改善了修饰印迹传感器的识别点.差分脉冲伏安法(DPV)表明苯巴比妥的浓度在1.0×10-8-1.8×10-4mol·L-1范围内呈现良好的线性关系(线性相关系数R=0.9994);检出限2.3×10-9mol·L-1(信噪比(S/N)=3).研究结果表明纳米氧化铜修饰过的印迹传感器具有较高灵敏度及选择性.此印迹传感器能用于实际样品中苯巴比妥的检测,加标回收率在95.0%-102.5%.     

柚皮苷分子印迹传感器的制备与应用

以邻氨基酚为单体,无电化学活性的柚皮苷为模板分子,采用循环伏安法(扫速为100mV/s)在碳电极上往复扫描30次,电聚合出具有识别柚皮苷分子功能的敏感膜。以扫描电子显微镜(SEM)、X射线全反射(XRR)及电化学方法对该印迹传感器进行表征。结果表明,印迹传感器敏感膜与非印迹膜在形貌结构和电化学特性方面有明显的不同。此传感器对柚皮苷有较好的选择性,响应快(30s),在6.0×10-5～1.4×10-4mol/L范围内呈线性关系,且重现性好(RSD=1.8%,n=5);传感器对柚皮苷的检出限为1.6×10-5mol/L。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.