Ni—Zn／活性炭催化剂的程序升温还原研究

采用ＴＰＲ技术对甲醇、乙醇羰基化反应的Ｎｉ／Ｃ和Ｎｉ－Ｚｎ／Ｃ催化剂进行了研究。实验发现，负载于活性炭上的ＮｉＯ比非负载的ＮｉＯ容易还原；Ｎｉ与Ｚｎ之间有相 互，Ｎｉ－Ｚｎ／Ｃ的还原峰温介于Ｎｉ／Ｃ与Ｚｎ／Ｃ之间，还原后的Ｎｉ／Ｃ和Ｎｉ－Ｚｎ／Ｃ催化剂比非负载ＮｉＯ还原后的Ｎｉ更易氧化；氧化后的Ｎｉ／Ｃ和Ｎｉ－Ｚｎ／Ｃ在相同的升温速率下再一次还原，其峰温θｍ比第一次还原时低３０－５０℃，而对Ｚｎ／     

Ni-Zn/活性炭催化剂的程序升温还原研究

采用ＴＰＲ技术对甲醇、乙醇羰基化反应的Ｎｉ／Ｃ和Ｎｉ－Ｚｎ／Ｃ催化剂进行了研究．实验发现，负载于活性炭上的ＮｉＯ比非负载的ＮｉＯ容易还原；Ｎｉ与Ｚｎ之间有相互作用，Ｎｉ－Ｚｎ／Ｃ的还原峰温介于Ｎｉ／Ｃ与Ｚｎ／Ｃ之间；还原后的Ｎｉ／Ｃ和Ｎｉ－Ｚｎ／Ｃ催化剂比非负载ＮｉＯ还原后的Ｎｉ更易氧化；氧化后的Ｎｉ／Ｃ和Ｎｉ－Ｚｎ／Ｃ在相同的升温速率下再一次还原，其峰温θｍ比第一次还原时低３０～５０℃，而对Ｚｎ／Ｃ的θｍ无影响．经反复氧化－还原操作，得到不同升温速率下的ＴＰＲ谱，提出一种用ＴＰＲ谱直接计算［Ｈ２］ｍ的方法，进而求得催化剂的还原活化能     

Cu/ZnO/Al2O3/ZrO2催化剂上乙醇脱氢合成乙酸乙酯Ⅰ.催化反应性能及机理

研究了经ＺｒＯ２改性的Ｃｕ／ＺｎＯ／Ａｌ２Ｏ的催化性能，考察了操作条件，ＺｒＯ２含量及不同原料的影响，发现经共沉淀法制备了Ｃｕ／ＺｎＯ／Ａｌ２Ｏ３／ＺｒＯ２具有最佳的反应活性及选择性以９５％乙醇为原料，在２６５℃，ＷＨＳＶ１．５ｈ＾－１，乙醇转化率为６９．０％，乙酸乙酯选择性为７０．２％，使用无水乙醇为原料要好地９５％乙醇，使用乙醛或醇醛混合原料，亦有乙酸乙酯生成，乙醇在此催化剂上的反应机理为乙醇     

Cu／ZnO／Al_2O_3／ZrO_2催化剂上乙醇脱氢合成乙酸乙酯Ⅰ．催化反应性能及机理

研究了经ＺｒＯ２改性的Ｃｕ／ＺｎＯ／Ａｌ２Ｏ３的催化性能，考察了操作条件、ＺｒＯ２含量及不同原料的影响．发现经共沉淀法制备的Ｃｕ／ＺｎＯ／Ａｌ２Ｏ３／ＺｒＯ２具有最佳的反应活性及选择性．以９５％乙醇为原料，在２６５℃，ＷＨＳＶ１．５ｈ－１时，乙醇转化率为６９．０％，乙酸乙酯选择性为７０．２％．使用无水乙醇为原料要好于９５％乙醇，使用乙醛或醇醛混合原料，亦有乙酸乙酯生成．乙醇在此催化剂上的反应机理为乙醇先在Ｃｕ上脱氢为乙醛，然后乙醛在酸碱双中心上发生Ｃａｎｎｉｚａｒｒｏ反应生成乙酸乙酯．还讨论了ＺｒＯ２的作用及催化剂活性降低的原因     

HZSM—5与ZnO／SiO2的固相反应

以乙烯、乙烷为探针反应分子，以混合不同锌含量的ＺｎＯ／ＳｉＯ２与ＨＺＳＭ－５为催化剂，在不同处理条件与不同混合方式（直接混合或机械研磨）下研究高温焙烧的催化剂对乙烯、乙烷芳构化反应的影响。考察了不同含量的Ｚｎ／ＨＺＳＭ－５上Ｃ２Ｈ４、Ｃ２Ｈ６的芳构化反应及ＮａＨＺＳＭ－５与ＺｎＯ／ＳｉＯ２和ＮａＺｎＨＺＳＭ－５与ＺｎＯ／ＳｉＯ２混合催化剂高温焙烧后的Ｃ２Ｈ４芳构化反应。发现Ｚｎ／ＨＺＳＭ－５是一种     

Ni系列催化剂上甲烷直接氧化制合成气

采用固定床流动反应装置，考察负载型Ｎｉ系列催化剂在甲烷直接氧化制合成气反应上的催化活性．空速为５．０×１０５ｈ－１，ＣＨ４／Ｏ２＝２条件下，不同Ｎｉ含量的催化剂中，１５％Ｎｉ／Ａｌ２Ｏ３活性较好．利用ＴＰＤ和ＸＲＤ技术将催化剂引发温度与催化剂组成进行关联，并在７００℃下考察空速对催化性能的影响．随着空速的增加，ＣＨ４的转化率增加，７．０×１０５ｈ－１时达到最大，与此同时，ＣＯ的选择性一直增加．实验结果说明在非平衡体系中，ＣＯ和Ｈ２是由ＣＨ４直接转化而来，ＣＯ２是ＣＯ深度氧化的产物，在此基础上对催化剂过程的机理作了初步的探讨．     

HZSM一5与ZnO／SiO_2的固相反应

以乙烯、乙烷为探针反应分子，以混合不同锌含量的ＺｎＯ／ＳｉＯ＿２，与ＨＺＳＭ－５为催化剂，在不同处理条件与不同混合方式（直接混合或机械研磨）下研究高温焙烧的俗化剂对乙烯、乙烷芳构化反应的影响。考察了不同含量的Ｚｎ／ＨＺＳＭ－５上Ｃ＿２Ｈ＿４、Ｃ＿２Ｈ＿６的芳构化反应及ＮａＨＺＳＭ－５与ＺｎＯ／ＳｉＯ＿２和ＮａＺｎＨＺＳＭ－５与ＺｎＯ／ＳｉＯ＿２混合催化剂高温焙烧后的Ｃ＿２Ｈ＿４芳构化反应。发现Ｚｎ／ＨＺＳＭ－５是一种双功能催化剂，乙烯、乙烷芳构化反应的活性和选择性均与Ｚｎ／ＨＺＳＭ－５的双中心Ｚｎ￣（２＋）和Ｂ酸的相互匹配有密切关系，Ｂ酸和Ｚｎ￣（２＋）存在最合适匹配。而ＮＺＳＭ－５与ＺｎＯ／ＳｉＯ＿２合催化剂高温焙烧后具有Ｚｎ／ＨＺＳＭ－５的双功能性，ＨＺＳＭ－５与ＺｎＯ／ＳｉＯ＿２在高温下发生了固相反应。     

Ni/Al2O3催化剂上甲烷部分氧化制合成气

本研究了Ｎｉ／Ａｌ２Ｏ３催化剂的表面特征以及其与ＣＨ４部分氧化制合成气反应性能的关系。ＴＰＲ，ＸＲＤ和评价结果表明，催化剂Ｎｉ组分含量在９．０％时反应性能最佳，反应过程中催化剂表面上部有部分镍氧化物在５２０～５４０℃就还原，反应条件实验表明，在１１．５２×１０＾５ ｍｌ．ｇ＾－１下，随着反应管外控制温度的升高，ＣＨ４转化率，ＣＯ和Ｈ２选择性及收率增加，在７００℃下，随着原料气空速的增加，ＣＨ４转     

甲醇与乙醇一步合成异丁醛用CuO-ZnO/Al2O3催化剂

在ＣｕＯ－ＺｎＯ／Ａｌ２Ｏ３催化剂上，甲醇与乙醇在常压和２１０￣３６０℃温度下一步反应合成异丁醛。利用正交设计方法，研究了ＣｕＯ－ＺｎＯ／Ａｌ２Ｏ３体系催化剂组成和制备条件等因素对催化剂催化性能的影响。结果表明，催化剂中ＣｕＯ含量对催化剂的催化活性影响最大，而ＺｎＯ含量则主要影响催化剂对异丁醛的选择性。催化剂制备条件，如沉淀温度、陈化时间等，也不同程度也影响催化剂的催化性能。ＸＲＤ和ＢＥＴ表征结果     

Zn／HZSM－5分子筛上乙烯、乙烷芳构化的协同作用机理

运用ＮＨ＿３－ＴＰＤ、ＩＲ－ＯＨ、Ｐｙ－ＩＲ、ＣＯ－ＩＲ及ＸＰＳ等手段对Ｚｎ／ＨＺＳＭ－５及其浸碱催化剂的酸组分和金属组分构成的Ｌ酸性质进行了表征，考察了催化剂对乙烯、乙烷的芳构化作用．发现Ｚｎ／ＨＺＳＭ－５中形成了Ｚｎ￣（２＋）－Ｌ强酸中心，使分子筛的Ｂ酸中心减少．浸碱也可使分子筛的Ｂ酸减少，芳构化反应的活性和选择性均与Ｚｎ／ＨＺＳＭ－５的双中心Ｚｎ￣（２＋）－Ｌ酸和Ｂ酸的相互匹配密切相关，Ｂ酸和Ｌ酸存在最适合匹配，因此Ｚｎ／ＨＺＳＭ－５在乙烯、乙烷芳构化反应中存在最佳锌含量．     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.