Surface and catalytic properties of Cu/Zn mixed oxide catalysts

Copper catalysts supported on zinc oxide, with different loading (1–20 wt.% CuO), were prepared by impregnation of the basic zinc carbonate with a water solution of copper nitrate. The impregnated samples were dried at 120°C and calcined at 400–700°C. The surface and catalytic properties of CuO loaded on ZnO were determined by N₂ adsorption measurements conducted at −196°C and CO oxidation by O₂ at 150–300°C, respectively. The results obtained revealed that the surface and catalytic properties of different solids were dependent upon CuO content and calcination temperature. The specific surface areas of various adsorbents decreased monotonically as a function of both calcination temperature and extent of loading. However, the activation energy of sintering, ΔE_S, was found to increase by increasing the amount of CuO present. On the other hand, the CO oxidation activity on various catalysts was found to increase progressively by increasing the calcination temperature from 400 to 500°C, then decreased by increasing the temperature from 500 to 700°C. The augmentation of CuO content from 1 to 5 wt.% resulted in an increase in the CO oxidation activity, which decreased by increasing the extent of loading above this limit.     

Flash pyrolysis of Silopi asphaltite in a free-fall reactor under vacuum

Flash pyrolysis experiments on asphaltite samples were performed in a free-fall reactor under vacuum to determine the effects of pyrolysis temperature, feed rate and particle size. Maximum liquid yield of 13 wt.% was obtained in free-fall reactor under vacuum when the pyrolysis temperature was 700 °C, feed rate was 0.4 g min⁻¹ and particle sizes were between 0.075 and 0.250 mm. The liquid products obtained at various pyrolysis conditions were analyzed by gas chromatography/mass spectrometer (GC/MS) and liquid products were classified as following: C5–C10, C11–C15, C16–C20 and C20+. The amount of saturated hydrocarbons decreased while the amount of unsaturated hydrocarbons increased with increase of temperature. While percent of C5–C10 unsaturated hydrocarbons continuously increased with increase of temperature, the percent of C11–C15 unsaturated hydrocarbons increased up to 750 °C and then started to diminish. Functional group analysis of solid residue was carried out using Fourier transform infrared spectrometry (FT-IR). The proximate analysis of solid residue indicated that percent of fixed carbon and ash increased with temperature.     

Pyrolysis of textile wastes: I. Kinetics and yields

Thermal behavior of textile waste was studied by thermogravimetry at different heating rates and also by semi-batch pyrolysis. It was shown that the onset temperature of mass loss is within 104–156 °C and the final reaction temperature is within 423–500 °C. The average mass loss is 89.5%. There are three DTG peaks located at the temperature ranges of 135–309, 276–394 and 374–500 °C, respectively. The first two might be associated with either with decomposition of the hemicellulose and cellulose or with different processes of cellulose decomposition. The third peak is possibly associated to a synthetic polymer. At a temperature of 460 °C, the expected amount of volatiles of this waste is within 85–89%. The kinetic parameters of the individual degradation processes were determined by using a parallel model. Their dependence on the heating rate was also established. The pyrolysis rate is considered as the sum of the three reaction rates. The pyrolysis in a batch reactor at 700 °C and nitrogen flow of 60 ml/min produces 72 wt.% of oil, 13.5 wt.% of gas and 12.5 wt.% of char. The kinetic parameters of the first peak do not vary with heating rate, while those of the second and the third peak increase and decrease, respectively, with an increasing heating rate, proving the existence of complex reaction mechanisms for both cases.     

Use of a MDI-functionalized reactive polymer for the manufacture of modified bitumen with enhanced properties for roofing applications

In this study, the suitability of a reactive polymer, synthesized by reaction of 4,4′-diphenylmethane diisocyanate (MDI) with a low molecular weight polyethylene-glycol (PEG), as a modifying agent for the manufacture of bitumen-based waterproof membranes, was evaluated. With that purpose, rheological and thermal analysis tests, and microstructural observations by AFM were carried out on different samples of modified bitumen having a MDI–PEG content ranging from 0 to 10 wt.%, cured at room temperature for a period of time within 0–30 days. The results obtained demonstrate that the addition of the reactive polymer proposed in this work to bitumen is very suitable at high in-service temperatures, because a noticeable increase in the values of viscosity, at 60 °C, of the resulting modified bitumen samples is observed on a time-scale of days. AFM observations, carried out at 50 °C, evidenced that the reactive polymer MDI–PEG leads to a new microstructure, displaying a higher level of stiffness. Therefore, this polymer should be seriously taken into consideration as a modifier of bituminous coatings for the waterproofing industry.     

Microemulsions of triglyceride and non-ionic surfactant — effect of temperature and aqueous phase composition

The phase behavior of soybean oil, polyoxyethylene (40) sorbitol hexaoleate and water—ethanol was investigated. Regions of water-in-oil (W/O) microemulsions were determined and were found to be strongly dependent on temperature and water:alcohol ratios. At a water:ethanol ratio of 80/20 (wt.%), an oil:surfactant ratio of 2/3 and a temperature of 25°C, the microemulsion region extended continuously from the oil—surfactant axis to the phase diagram center. However, at the hydrophilic—lipophilic balance (HLB) temperature (20–22°C) and a water:ethanol ratio of 80/20 or 75/25 (wt.%), a single-phase area separated from the original microemulsion region. Conductivity measurements and dynamic light scattering intensifies at 25°C indicated that association structures were formed with increasing aqueous phase concentrations above 15 wt.%. At 20°C, the single-phase scattering intensifies increased sharply with increasing aqueous phase concentrations (38–46 wt.%) and a plateau in the conductivity was detected.

Transmission electron microscopy results supported the finding that more particles are formed with increasing aqueous phase and form connected particles, resulting in constant conductance.     

Stability studies of arsenate, monomethylarsonate, dimethylarsinate, arsenobetaine and arsenocholine in deionized water, urine and clean-up dry residue from urine samples and determination by liquid chromatography with microwave-assisted oxidation-hydride generation atomic absorption spectrometric detection

The stability of arsenate, monomethylarsonate, dimethylarsinate (DMA), arsenobetaine (AsB) and arsenocholine (AsC) at a concentration of 200 μg l⁻¹ in deionized water, urine and dry clean-up residue of urine, stored in dark at −20 °C, 4 °C and ambient temperature, without the addition of any stabilizer reagent was evaluated. The five species were determined independently by liquid chromatography with microwave-assisted oxidation-hydride generation atomic absorption spectrometric detection. At −20 °C, all species were stable in water and untreated urine; at 4 °C and ambient temperature, they were stable during the 67 days of testing in the urine dry residue after the clean-up procedure. In untreated urine samples at 4 °C and ambient temperature, AsC is unstable and easily transformed to the more oxidized species, AsB. In deionized water, AsB and AsC are transformed to other species such as DMA. The dry urine residue may be a good matrix as a reference material for As species.     

Study of the thermal degradation of poly(furfuryl methacrylate) by thermogravimetry

The thermal degradation of poly(furfuryl methacrylate) (PFM) has been studied by means of dynamic thermogravimetric analysis (TGA) in the temperature range 100–600°C under nitrogen and oxygen atmospheres at various heating rates, and the apparent activation energy for the interval 230–340°C corresponding to the first degradation step was determined. Isothermal TGA at 250°C, 275°C and 300°C was carried out and the apparent activation energy values obtained were compared with those determined in dynamic experiments. The residues from isothermal degradation experiments were analysed by infrared spectroscopy and the results seem to indicate that in the thermal degradation of PFM the formation of cyclic structures of 2,4-dimethylglutaric anhydride occurs in the macromolecular chains, together with partial depolymerization of polymer segments, as well as intermolecular crosslinking through oxidation of the C---H bond in position 5 of some furfuryl rings.     

Pressurized solvent extraction and monolithic column-HPLC/DAD analysis of anthocyanins in red cabbage

The aim of this work was to develop a fast method for extraction and analysis of anthocyanins in red cabbage. Pressurized hot water containing 5% of ethanol was used as an extremely efficient extraction solvent. HPLC/DAD with a monolithic column was used to accomplish a fast analysis—24 anthocyanin peaks within 18 min. Statistical design was used to optimize the studied extraction parameters: temperature (80–120 °C); sample amount (1–3 g); extraction time (6–11 min); concentration of formic acid in the extraction solvent (0–5 vol.%). The best extraction conditions for a majority of the anthocyanin peaks were 2.5 g of sample, 99 °C (at 50 bar), 7 min of extraction and a solvent composition of water/ethanol/formic acid (94/5/1, v/v/v).     

Pyrolytic synthesis of long strands of large diameter single-walled carbon nanotubes at atmospheric pressure in the absence of sulphur and hydrogen

We describe the synthesis of cm-long strands consisting of single-walled carbon nanotube ropes. The method involves the thermolysis of ferrocene (FeCp₂)–alcohol solutions under an Ar atmosphere at 800–950 °C. The tubes within strands could exhibit large diameters (2–3.5 nm OD) in high yields by either increasing the ferrocene concentration in the alcohol solution or by increasing the pyrolysis temperature. We noted that the nanotube material with the highest degree of crystallinity was produced at 950 °C, and as the ferrocene concentration in the alcohol solution increases (e.g., 1.2 wt%), the tubes tend to be metallic. This method appears to be simple, safer and more efficient than others reported in the literature because it does not require vacuum, sulphur agents, relatively high temperatures or large amounts of H₂.     

Interaction of sodium cholate with dioctadecyldimethylammonium chloride vesicles in aqueous dispersion

Mixtures of dioctadecyldimethylammonium chloride (DODAC) cationic vesicle dispersions with aqueous micelle solutions of the anionic sodium cholate (NaC) were investigated by differential scanning calorimetry, DSC, turbidity and light scattering. Within the concentration range investigated (constant 1.0 mM DODAC and varying NaC concentration up to 4 mM), vesicle → micelle → aggregate transitions were observed. The turbidity of DODAC/NaC/water depends on time and NaC/DODAB molar concentration ratio R. At equilibrium, turbidity initially decreases smoothly with R to a low value (owing to the vesicle–micelle transition) when R = 0.5–0.8 and then increases steeply to a high value (owing to the micelle–aggregate transition) when R = 0.9–1.0. DSC thermograms exhibit a single and sharp endothermic peak at T_m ≈ 49 °C, characteristic of the melting temperature of neat DODAC vesicles in water. Upon addition of NaC, T_m initially decreases to vanish around R = 0.5, and the main transition peak broadens as R increases. For R > 1.0 two new (endo- and exothermic) peaks appear at lower temperatures indicating the formation of large aggregates since the dispersion is turbid. All samples are non-birefringent. Dynamic light scattering (DLS) data indicate that both DODAC and DODAC/NaC dispersions are highly polydisperse, and that the mean size of the aggregates tends to decrease as R increases.     

Sunna 535-nm photo-fluorescent film dosimeter response to different environmental conditions

Evaluations on the influence of environmental variabilities on the red fluorescence component of the Sunna Model γ photo-fluorescent dosimeter^TM have previously been reported. This present paper describes the environmental effects on the response of the green fluorescence component of the same dosimeter, which is manufactured using the injection molding technique. The results presented include temperature, relative humidity, and light influences both during and after irradiation. The green fluorescence signal shows a significant dependence on irradiation temperature below room temperature at 1%/°C. Above room temperature (approximately 24–60°C), the irradiation temperature effect varies from −0.1%/°C to 1.0%/°C, depending on the absorbed dose level. For facilities with irradiation temperatures between 30°C and 60°C and absorbed dose levels above 10 kGy, irradiation temperature effects are minimal. Light-effects results indicate that the dosimeter is influenced by ultraviolet and blue wavelengths during irradiation as well as during the post-irradiation stabilization period (approximately 22 h), requiring the use of light-tight packaging. Results also show that the dosimeter exhibits negligible effects from ambient moisture during and after irradiation when in the range of 33–95% relative humidity.     

Microporous poly(vinyl methyl ether) hydrogels prepared by γ-ray irradiation at different heating rates

We prepared thermoresponsive and microporous polymer hydrogels by γ-ray irradiation of aqueous solutions poly(vinyl methyl ether) (PVME) at different heating rates. Under all temperature programs, opaque and heterogeneous PVME gels formed, which swelled at temperatures below the lower critical solution temperature and shrank at temperatures above it. All of the samples contained porous and phase-separated structures. The shape and size of the gel pores varied depending on the temperature programs. Gels having a sponge-like continuous porous structure formed only when the radiation-induced crosslinking was carried out at an optimum heating rate, which we found to be 0.11–0.13°C min⁻¹. For temperature changes between 10°C and 40°C, gels with this structure showed rapid volume transitions on a time scale of about a minute.     

Methods for separation of trace amounts of platinum and investigation of the influence of interfering elements during platinum determination in copper ores and copper concentrates by graphite furnace atomic absorption spectrometry

A THGA graphite furnace with Zeeman background correction has been used to determine platinum content in copper ore and copper concentrate at the part per billion (ppb) concentration level. Two different procedures for the separation of trace platinum have been applied: (i) use of an ion exchange resin; and (ii) a two-stage method based on platinum separation on inorganic carriers. The influence of interfering elements in the matrix (Cu, Pb, Fe, Ti, V, Au, Pd, Ir, Rh and Al) has been examined using a graphite furnace. It was found that the presence of Cu (12.5–100 mg l⁻¹), Pb (100–500 mg l⁻¹), Fe (100–2000 mg l⁻¹), Ti (25–100 mg l⁻¹), V (25–100 mg l⁻¹), Au (25–300 mg l⁻¹), Pd (20–250 mg l⁻¹), Ir (0.5–3.5 mg l⁻¹) and Rh (0.025–1 mg l⁻¹) in the samples analyzed has no effect on the platinum absorption signal when using a recommended temperature program (T_pyr=1300°C, T_at=2450°C). Spectral interference was observed, which was due to aluminum, as a result of the close neighborhood of the Pt 265.945-nm and Al 266.039-nm lines. This interference could not be eliminated by the Zeeman background correction.     

Constrained polymer layers to reduce noise: reality or fiction?—An experimental inquiry into their effectiveness

The frequency and temperature dependent noise radiation properties of constrained polymer layered oil pans are examined through mobility and intensity measurements. Four metal/polymer/metal sandwich composites of varied thermo-plastic elastomer systems of polystyrene–polybutadiene–polystyrene triblock copolymers are investigated within a wide frequency range covering 1000–5000 Hz, and over a wide temperature range covering 20–100 °C, with results compared to those of an ordinary steel oil pan. The mobility and intensity are found to be strongly frequency and temperature dependent, displaying a substantial mobility reduction as compared to that of the ordinary pan, while using the constrained layer damping configurations at their maximum loss factor temperatures. However, the reduction of noise radiation is smaller than that of the mobility at those temperatures, mainly due to the increased radiation efficiency while adding damping materials.     

Temperature dependence of the rate constant for reactions of hydrated electrons with H, OH and H2O2

The temperature dependence of the rate constants, for the reactions of hydrated electrons with H atoms, OH radicals and H₂O₂ has been determined. The reaction with H atoms, studied in the temperature range 20–250°C gives k(20°C) = 2.4 × 10¹⁰M^-1s¹ and the activation energy E_A = 14.0 kJ mol^-1 (3.3 kcal mol^-1). For reaction with OH radicals the corresponding values are, k(20°C) = 3.1 × 10¹⁰M^-1s^-1 and E_A = 14.7 kJ mol^-1 (3.5 kcal mol^-1) determined in the temperature range 5–175°C. For reaction with H₂O₂ the values are, k(20°C) = 1.2 × 10¹⁰M^-1s^-1 and E_A = 15.6 kJ mol^-1 (3.7 kcal mol^-1) measured from 5–150°C. Thus, the activation energy for all three fast reactions is close to that expected for diffusion controlled reactions. As phosphates were used as buffer system, the rate constant and activation energy for the reaction of hydrated electron with H₂PO₄^- was determined to k(20°C) = 1.5 × 10⁷M^-1s^-1 and E_A = 7.4 kJ mol^-1 (1.8 kcal mol^-1) in the temperature range 20–200°C.     

Resistance properties of a macroporous silica-based N,N,N′,N′-tetraoctyl-3-oxapentane-1,5-diamide-impregnated polymeric adsorption material against nitric acid, temperature and γ-irradiation

The resistance of a novel silica-based N,N,N′,N′-tetraoctyl-3-oxapentane-1,5-diamide (TODGA) polymeric adsorption material (TODGA/SiO₂-P) against nitric acid, temperature and γ-irradiation had been investigated. The adsorption property of the treated TODGA/SiO₂-P was evaluated by a 3 M HNO₃ solution containing 0.01 M Nd(III). It was found that both 3 and 0.01 M HNO₃ concentrations did not decrease the stability of TODGA/SiO₂-P at 25°C. The quantity of TODGA leaked from TODGA/SiO₂-P was equivalent to its solubility in the corresponding HNO₃ aqueous solution. The effect of 3 M HNO₃ on the leakage of TODGA at 80°C was significantly higher than that in 0.01 M HNO₃ as well as in all cases at 25°C. The amount of Nd(III) adsorbed towards the treated TODGA/SiO₂-P was determined in the range of 0.143–0.148 mmol/g for the HNO₃ concentration effect and 0.142–0.0506 mmol/g for the temperature effect. γ-Irradiation showed a more noticeable destruction effect on TODGA/SiO₂-P. The content of TODGA leaked increased with an increase in the γ-irradiation dose (ID) from 1.06 to 3.72 MGy in terms of the linear equation [TODGA]=794.5ID+84.0. The amount of Nd(III) adsorbed onto the irradiated TODGA/SiO₂-P decreased rapidly from 0.134 to 0.0438 mmol/g, which was lower than 0.153 mmol/g, the adsorption of fresh TODGA/SiO₂-P for Nd(III), according to the equation Q_Nd(III)=−0.0301ID+0.160, showing that a large quantity of TODGA leaked from TODGA/SiO₂-P. The adsorbed amount of Nd(III) decreased obviously in this order: the HNO₃ concentration effect, temperature effect and γ-irradiation.     

Stability of phospholipid vesicles studied by asymmetrical flow field-flow fractionation and capillary electrophoresis

The stability of zwitterionic phosphatidylcholine vesicles in the presence of 20 mol% phosphatidyl serine (PS), phosphatidic acid (PA), phosphatidyl inositol (PI), and diacylphosphatidyl glycerol (PG) phospholipid vesicles, and cholesterol or calcium chloride was investigated by asymmetrical flow field-flow fractionation (AsFlFFF). Large unilamellar vesicles (LUV, diameter 100 nm) prepared by extrusion at 25 °C were used. Phospholipid vesicles (liposomes) were stored at +4 and −18 °C over an extended period of time. Extruded egg yolk phosphatidylcholine (EPC) particle diameters at peak maximum and mean measured by AsFlFFF were 101 ± 3 nm and 122 ± 5 nm, respectively. No significant change in diameter was observed after storage at +4 °C for about 5 months. When the storage period was extended to about 8 months (250 days) larger destabilized aggregates were formed (172 and 215 nm at peak maximum and mean diameters, respectively). When EPC was stored at −18 °C, large particles with diameters of 700–800 nm were formed as a result of dehydration, aggregation, and fusion processes. In the presence of calcium chloride, EPC alone did not form large aggregates. Addition of 20 mol% of negatively charged phospholipids (PS, PA, PI, or PG) to 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphatidylcholine (POPC) vesicles increased the electrostatic interactions between calcium ion and the vesicles and large aggregates were formed. In the presence of cholesterol, large aggregates of about 250–350 nm appeared during storage at +4 and −18 °C for more than 1 day.

The effect of liposome storage temperature on phospholipid coatings applied in capillary electrophoresis (CE) was studied by measuring the electroosmotic flow (EOF). EPC coatings with and without cholesterol, PS, or calcium chloride, prepared from liposomes stored at +25, +4, and −18 °C, were studied at 25 °C. The performances of the coatings were further evaluated with three uncharged compounds. Only minor differences were observed between the same phospholipid coatings, showing that phospholipid coatings in CE are relatively insensitive to storage at +25, +4 °C or −18 °C.     

Effect of process parameters on transmembrane flux during direct osmosis

Direct osmosis is a non-thermal membrane process employed for the concentration of fruit juices at ambient temperature and atmospheric pressure, thereby maintaining the organoleptic and nutritional properties of fruit juices. In the present study, concentration of pineapple juice by direct osmosis was explored. Aqueous solution of sucrose (0–40%, w/w)–sodium chloride (0–26%, w/w) combination was investigated as an alternative osmotic agent. The sucrose–sodium chloride combination can overcome the drawback of sucrose (low flux) and sodium chloride (salt migration) as osmotic agents during direct osmosis process. The effect of the hydrodynamic conditions in the module and feed temperature (25–45 °C) on transmembrane flux was evaluated. For a range of hydrodynamic conditions studied, it was observed that transmembrane flux increases with Reynolds number. The increase in feed temperature resulted in an increase in transmembrane flux. The pineapple juice was concentrated upto a total soluble solids content of 60 °Brix at ambient temperature. The effect of direct osmosis process on physico-chemical characteristics of pineapple juice was also studied. The ascorbic acid content was well preserved in the pineapple juice concentrate by direct osmosis process.     

The direct synthesis of dimethyl ether from syngas over hybrid catalysts with sulfate-modified γ-alumina as methanol dehydration components

A series of γ-Al₂O₃ samples modified with various contents of sulfate (0–15 wt.%) and calcined at different temperatures (350–750 °C) were prepared by an impregnation method and physically admixed with CuO–ZnO–Al₂O₃ methanol synthesis catalyst to form hybrid catalysts. The direct synthesis of dimethyl ether (DME) from syngas was carried out over the prepared hybrid catalysts under pressurized fixed-bed continuous flow conditions. The results revealed that the catalytic activity of SO₄²⁻/γ-Al₂O₃ for methanol dehydration increased significantly when the content of sulfate increased to 10 wt.%, resulting in the increase in both DME selectivity and CO conversion. However, when the content of sulfate of SO₄²⁻/γ-Al₂O₃ was further increased to 15 wt.%, the activity for methanol dehydration was increased, and the selectivity for DME decreased slightly as reflected in the increased formation of byproducts like hydrocarbons and CO₂. On the other hand, when the calcination temperature of SO₄²⁻/γ-Al₂O₃ increased from 350 °C to 550 °C, both the CO conversion and the DME selectivity increased gradually, accompanied with the decreased formation of CO₂. Nevertheless, a further increase in calcination temperature to 750 °C remarkably decreased the catalytic activity of SO₄²⁻/γ-Al₂O₃ for methanol dehydration, resulting in the significant decline in both DME selectivity and CO conversion. The hybrid catalyst containing the SO₄²⁻/γ-Al₂O₃ with 10 wt.% sulfate and calcined at 550 °C exhibited the highest selectivity and yield for the synthesis of DME.     

Raman scattering study of highly fluorinated graphite

Raman spectra of highly fluorinated C_xF samples (1<x<2) prepared at room temperature and 515°C were measured. C_xF samples prepared at room temperature exhibited two Raman bands at 1593–1583 and 1555–1542 cm⁻¹. Graphite samples fluorinated at 515°C for 1 and 2 min also gave similar bands at 1581–1580 and 1550–1538 cm⁻¹. However, graphite samples fluorinated from 15 min to 10 h at 515°C no longer showed such spectra. The Raman peaks shifted to lower frequencies with increasing fluorine concentration in C_xF. This trend is due to the weakening of the C---C bonds of the graphene layers. Observation of both kinds of Raman bands suggests the coexistence of two highly fluorinated phases, C₂F and C₁F, in the samples. The process of formation of graphite fluoride is discussed on the basis of the Raman spectra of C_xF samples obtained at 515°C.