Structural investigation on PEO-based polymer electrolytes dispersed with Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles

Thin solid polymer electrolytes based on polyethylene oxide (PEO) and silver triflate (AgCF₃SO₃) dispersed with various concentrations of aluminum oxide (Al₂O₃) nanoparticles have been prepared by solution casting technique. These thin polymer films are found to have thickness of the order of 30 to 100 μm. The X-ray diffraction (XRD) patterns have indicated the amorphous nature of the polymer electrolyte. The differential scanning calorimeter (DSC) traces showed slight change in the glass transition temperature (T _g) whereas the degree of crystallization (X _c) decreases markedly due to the addition of alumina nanoparticles. Fourier transform infrared (FTIR) spectral analysis of all these samples has revealed the presence of absorption bands around 1,000 cm⁻¹; thus indicating the complexation of silver ions with oxygen in PEO. Employing the Wagner’s polarization technique as the standard method, the total ionic transference number for the complexed polymer electrolyte was found to be approximately unity thereby revealing that the significant contribution to electrical conduction was due to ions only. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, December 7–9, 2006     

The effective reinforcement of magnesium alloy ZK60A using Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles

ZK60A nanocomposite containing Al₂O₃ nanoparticle reinforcement (50 nm average size) was fabricated using solidification processing followed by hot extrusion. The nanocomposite exhibited similar grain size to the monolithic alloy, reasonable Al₂O₃ nanoparticle distribution, non-dominant (0 0 0 2) texture in the longitudinal direction, and 15% higher hardness than the monolithic alloy. Compared to the monolithic alloy (in tension), the nanocomposite exhibited lower yield strength (0.2%TYS) (−4%) and higher ultimate strength (UTS), failure strain, and work of fracture (WOF) (+13%, +170%, and +200%, respectively). Compared to the monolithic alloy (in compression), the nanocomposite exhibited lower yield strength (0.2%CYS) (−5%) and higher ultimate strength (UCS), failure strain, and WOF (+6%, +41%, and +43%, respectively). The effects of Al₂O₃ nanoparticle addition on the enhancement of tensile and compressive properties of ZK60A are investigated in this article.     

Fabrication of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Al structure by nitric acid oxidation at room temperature

A thick Al₂O₃/aluminum (Al) structure has been fabricated by oxidation of Al with 68wt% and 98wt% nitric acid (HNO₃) aqueous solutions at room temperature. Measurements of the Al₂O₃ thickness vs. the oxidation time show that reaction and diffusion are the rate-determining steps for oxidation with 68wt% and 98wt% HNO₃ solutions, respectively. Observation of transmission electron micrographs shows that the Al₂O₃ layer formed with 68wt% HNO₃ has a structure with cylindrically shaped pores vertically aligned from the Al₂O₃ surface to the Al₂O₃/Al interface. Due to the porous structure, diffusion of HNO₃ proceeds easily, resulting in the reaction-limited oxidation mechanism. In this case, the Al₂O₃/Al structure is considerably rough. The Al₂O₃ layer formed with 98wt% HNO₃ solutions, on the other hand, possesses a denser structure without pores, and the Al₂O₃/Al interface is much smoother, but the thickness of the Al₂O₃ layer formed on crystalline Al regions is much smaller than that on amorphous Al regions. Due to the relatively uniform Al₂O₃ thickness, the leakage current density flowing through the Al₂O₃ layer formed with 68wt% HNO₃ is lower than that formed with 98wt% HNO₃.     

The structure and properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Al coatings deposited by microarc oxidation on graphite substrates

Protective α-Al₂O₃ coatings on the surface of a graphite article have been obtained by method of electric-arc metallization with aluminum and microarc oxidation (anodic spark process). Investigation of the obtained coating by scanning electron microscopy (SEM), X-ray diffraction (XRD), and proton elastic recoil detection analysis (ERDA) showed good quality of the Al and α-Al₂O₃ coatings on graphite. The proposed technology can be used for obtaining protective coatings in low-accessible sites of graphite articles.     

Modification of the Al<Subscript>2</Subscript>O<Subscript>3</Subscript> surface by high-energy bismuth ions

This paper reports on an atomic-force microscopy study of the surface of α-Al₂O₃ single crystals irradiated by Bi ions with energies of 710, 557, 269, and 151 MeV. The shape of the radiation defects produced by single ions was established to depend on the ionization energy loss. The threshold ionization density above which the surface topography is observed to change lies in the 27–35 keV/nm interval. Possible mechanisms of defect formation in the thermal-spike model, namely, a phase transition and the creation of thermoelastic stresses in the high-energy ion track, are considered.     

Minimizing of the boundary friction coefficient in automotive engines using Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and TiO<Subscript>2</Subscript> nanoparticles

Minimizing of the boundary friction coefficient is critical for engine efficiency improvement. It is known that the tribological behavior has a major role in controlling the performance of automotive engines in terms of the fuel consumption. The purpose of this research is an experimental study to minimize the boundary friction coefficient via nano-lubricant additives. The tribological characteristics of Al₂O₃ and TiO₂ nano-lubricants were evaluated under reciprocating test conditions to simulate a piston ring/cylinder liner interface in automotive engines. The nanoparticles were suspended in a commercially available lubricant in a concentration of 0.25 wt.% to formulate the nano-lubricants. The Al₂O₃ and TiO₂ nanoparticles had sizes of 8–12 and 10 nm, respectively. The experimental results have shown that the boundary friction coefficient reduced by 35–51% near the top and bottom dead center of the stroke (TDC and BDC) for the Al₂O₃ and TiO₂ nano-lubricants, respectively. The anti-wear mechanism was generated via the formation of protective films on the worn surfaces of the ring and liner. These results will be a promising approach for improving fuel economy in automotive.

Open image in new window

Graphical Abstract Minimizing of the boundary friction coefficient in automotive engines using Al₂O₃ and TiO₂ nanoparticles

     

Electronic excitations and defects in nanostructural Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

A time-resolved cathodo-and photoluminescence study of nanostructural modifications of Al₂O₃ (powders and ceramics) excited by heavy-current electron beams, as well as by pulsed synchrotron radiation, is reported. It was found that Al₂O₃ nanopowders probed before and after Fe⁺ ion irradiation have the same phase composition (the γ-phase/δ-phase ratio is equal to 1), an average grain size equal to ～17 nm, and practically the same set of broad cathodoluminescence (CL) bands peaking at 2.4, 3.2, and 3.8 eV. It was established that Al₂O₃ nanopowders exhibit fast photoluminescence (PL) (a band at 3.2 eV), whose decay kinetics is described by two exponential stages (τ₁ = 0.5 ns, τ₂ = 5.5 ns). Three bands, at 5.24, 6.13, and 7.44 eV, were isolated in the excitation spectrum of the fast PL. Two alternate models of PL centers were considered, according to which the 3.2-eV luminescence either originates from radiative relaxation of the P^? centers (anion-cation vacancy pairs) or is due to the formation of surface analogs of the F⁺ center (F _S ⁺ -type centers). In addition to the fast luminescence, nano-Al₂O₃ was found to produce slow luminescence in the form of a broad band peaking at 3.5 eV. The excitation spectrum of the 3.5-eV luminescence obtained at T = 13 K exhibits two doublet bands with maxima at 7.8 and 8.3 eV. An analysis of the luminescent properties of nanostructural and single-crystal Al₂O₃ suggests that the slow luminescence of nanopowders at 3.5 eV is due to radiative annihilation of excitons localized near structural defects.     

Structural and catalytic properties of ZnO and Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanostructures loaded with metal nanoparticles

Nanostructured zinc oxide (ZnO) nanobelts and aluminum oxide (Al₂O₃) nanoribbons have been grown successfully from the vapor phase. XRD results confirmed the purity and the high quality of the formed crystalline materials. TEM images showed that ZnO nanostructures grew in the commonly known tetrapod structure with nanobelts separated from the tetrapods with an average width range of 10–30 nm and a length of about 500 nm. Al₂O₃ nanostructures grew in the form of nanoribbons with an average width range of 20–30 nm and a length of up to 1 μm. The catalytic oxidation of CO gas into CO₂ gas over the synthesized nanostructures is also reported. Higher catalytic activity was observed for Pd nanoparticles loaded on the ZnO nanobelts (100% conversion at 270 °C) and Al₂O₃ nanoribbons (100% conversion at 250 °C). The catalytic activity increased in the order Cu < Co < Au < Pd for the metal-loaded nanostructures. The preparation methods could be applied for the synthesis of novel nanostructures of various materials with novel properties resulting from the different shapes and morphologies.     

Formation and mechanical properties of alumina ceramics based on Al<Subscript>2</Subscript>O<Subscript>3</Subscript> micro- and nanoparticles

Alumina micro- and nanopowders with the particle size from 200 μm to 40 nm synthesized by the sol-gel method are studied. The particle size dependence of γ-Al₂O₃→α-Al₂O₃ phase transformation is studied by differential thermal analysis, X-ray diffraction method, and transmission electron microscopy. X-ray diffraction data show that for alumina nanoparticles γ-Al₂O₃→θ-Al₂O₃ phase transformation occurs at 900°C, and for micro-particles it occurs in the temperature range 1150–1200°C. The alumina ceramics produced of alumina nanoparticles is shown to have higher flexural strength under three-point bending than the ceramics produced of micro-particles. The obtained results demonstrate that alumina particle size reduction stabilizes the formation of α-Al₂O₃ at lower temperatures, due to which the grain growth rate decreases and the flexural strength of monolithic oxide ceramics increases.     

UV-protection properties of electrospun polyacrylonitrile nanofibrous mats embedded with MgO and Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles

This article describes the ultraviolet (UV) protection of MgO and Al₂O₃ nanoparticles embedded electrospun polyacrylonitrile (PAN) nanofibrous mats. UV radiation is a harmful part of sunlight and prolonged exposure to it can cause serious skin damages. In this research, nanofibrous mats consisting of nanofibers with different diameters containing different amounts of MgO, Al₂O₃, MgO Plus, and Al₂O₃ Plus nanoparticles were produced, and their UV-protection was measured. The specific surface area of MgO, MgO Plus, Al₂O₃, and Al₂O₃ Plus nanoparticles was 230, 600, 275, and 550 m²/g, respectively. The mean diameter of electrospun PAN nanofibers embedded with metal oxide nanoparticles was in the range of 665–337 nm. The results showed that the UV-protection (shielding) capability of the mats strongly depends on fiber diameter; in fact a thin mat of nanofibers has a much stronger UV-protection in comparison to a thicker mat composed of regular fibers. UV transmission is reduced as a result of embedding MgO and Al₂O₃ nanoparticles in the electrospun PAN nanofibrous mats. MgO Plus and Al₂O₃ Plus show higher UV-protection than MgO and Al₂O₃.     

Thermal hysteresis of a simulated Al<Subscript>2</Subscript>O<Subscript>3</Subscript> system

Thermal hysteresis in a simulated Al₂O₃ system has been investigated using a Molecular Dynamics (MD) method. Simulations were done in the basic cube under periodic boundary conditions containing 3000 ions with Born-Mayer type pair potentials. The system was cooled down from 7000 K to 0 K and heated up from 0 K to 7000 K by the same cooling/heating rate of 1.7178×10¹⁴ K/s. The temperature dependence of the system density upon cooling and heating shows thermal hysteresis. The differences between structure and dynamics of the models obtained by cooling (MOBC) and heating (MOBH) at three different temperatures of 2100 K, 3500 K and 5600 K have been detected. Calculations show that the differences in the dynamics of the systems are more pronounced than those in the structure. Furthermore, dynamical heterogeneities in MOBC and MOBH at the temperature of 2100 K have been studied through a non-Gaussian parameter and comparison of partial radial distribution functions (PRDFs) for the 10% most mobile or immobile particles with their corresponding mean ones. Cluster size distributions of the 10% most mobile or immobile particles in MOBC and MOBH at the temperature of 2100 K have been obtained. Calculations show that differences in dynamical heterogeneities are pronounced.     

Properties of an Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Si interface

The phase chemical composition of an Al₂O₃/Si interface formed upon molecular deposition of a 100-nm-thick Al₂O₃ layer on the Si(100) (c-Si) surface is investigated by depth-resolved ultrasoft x-ray emission spectroscopy. Analysis is performed using Al and Si L_{2, 3} emission bands. It is found that the thickness of the interface separating the c-Si substrate and the Al₂O₃ layer is approximately equal to 60 nm and the interface has a complex structure. The upper layer of the interface contains Al₂O₃ molecules and Al atoms, whose coordination is characteristic of metallic aluminum (most likely, these atoms form sufficiently large-sized Al clusters). The shape of the Si bands indicates that the interface layer (no more than 10-nm thick) adjacent to the substrate involves Si atoms in an unusual chemical state. This state is not typical of amorphous Si, c-Si, SiO₂, or SiO_x (it is assumed that these Si atoms form small-sized Si clusters). It is revealed that SiO₂ is contained in the vicinity of the substrate. The properties of thicker coatings are similar to those of the 100-nm-thick Al₂O₃ layer and differ significantly from the properties of the interfaces of Al₂O₃ thin layers.     

EPR study of ordered Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-based aerogel

Samples of oriented aerogel based on aluminum oxide are studied by the electron paramagnetic resonance (EPR) technique under steady-state and pulse conditions. At least two types of paramagnetic centers interacting with Al nuclei on the surface of aerogel are revealed. Their spectra are characterized by the presence or absence of superhyperfine structure in the EPR spectra, respectively. The X-ray irradiation at room temperature gives rise to the formation of additional long-lived paramagnetic centers of the second kind. Their characteristic decay times for the “fast” and “slow” processes are determined. The interaction of induced paramagnetic centers with protons located on the surface of aerogel is revealed.     

Crystal structure and magnetic properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles by <Superscript>27</Superscript>Al NMR data

The magnetization of a series of Al₂O₃ with different particle sizes and their ²⁷Al NMR spectra have been studied at room temperature. The field dependence of the magnetization demonstrated the existence of a long-range ferromagnetic order in a small part of the sample at room temperature; however, the relative volume of this contribution was very small (less than 1%), and this seems likely due to an impurity phase. The NMR spectra did not contain any lines of metallic aluminum the existence of which in these nanooxides was assumed before in a surface layer of the nanoparticles, according to the data of other techniques. The data on the phase composition and the charge distribution in different phases of the Al₂O₃ nanoparticles have been obtained. The change in the mean particle size (by a factor of almost three) only insignificantly changed their phase composition.     

Synthesis and magnetic properties of FeNi<Subscript>3</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> core-shell nanocomposites

In this study, FeNi₃/Al₂O₃ core-shell nanocomposites, where individual FeNi₃ nanoparticles were coated with a thin layer of alumina, were fabricated by a modified sol-gel method. Several physical characterizations were performed on the samples of FeNi₃/Al₂O₃ nanocomposites with different thickness of Al₂O₃ shell. The encapsulation of FeNi₃ nanoparticles with alumina stops FeNi₃ agglomeration during heat treatment, and prevents interaction among the closely spaced magnetic FeNi₃ nanoparticles. The Al₂O₃ insulating shell improves the soft magnetic properties of FeNi₃. The study of the complex permeability of the samples shows that the real part μ’ of the permeability of the sample with Al molar content of 20% (Al/(Fe+Ni)) is as high as 12, and independent of frequency up to at least 1 GHz. The tunneling magnetoresistance arising from the presence of the Al₂O₃ shell have also been studied.     

Metastable superconductivity of the Al/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> interface

Superconductivity in the interface region between metallic Al and its oxide, Al₂O₃, has been detected at about 45 K in the measured dynamic magnetic susceptibility.     

Al<Subscript>2</Subscript>O<Subscript>3</Subscript> plasma production during pulsed laser deposition

A Nd:YAG laser operating in second harmonic (532 nm), 3 ns pulse duration, 150 mJ pulse energy, and 10 Hz repetition rate, is employed to irradiate Al₂O₃ target placed in high vacuum. The produced plasma is investigated by an ion collector used in time-of-flight configuration and by a mass quadrupole spectrometer, in order to determine the equivalent plasma temperature and the atomic and molecular composition. Pulsed laser deposition technique has been used to produce thin films on different substrates placed close to the target. Different surface analyses, such as energy dispersive X-ray fluorescence (EDXRF), X-ray photoelectron spectroscopy (XPS) and surface profilometry are employed to characterize the produced films. Measurements of ablation yield, plasma equivalent temperature, acceleration voltage and characterization of grown thin films are presented and discussed.     

Metallic liquid hydrogen and likely Al<Subscript>2</Subscript>O<Subscript>3</Subscript> metallic glass

Dynamic compression has been used to synthesize liquid metallic hydrogen at 140 GPa (1.4 million bar) and experimental data and theory predict Al₂O₃ might be a metallic glass at ∼ 300 GPa. The mechanism of metallization in both cases is probably a Mott-like transition. The strength of sapphire causes shock dissipation to be split differently in the strong solid and soft fluid. Once the 4.5-eV H-H and Al-O bonds are broken at sufficiently high pressures in liquid H₂ and in sapphire (single-crystal Al₂O₃), electrons are delocalized, which leads to formation of energy bands in fluid H and probably in amorphous Al₂O₃. The high strength of sapphire causes shock dissipation to be absorbed primarily in entropy up to ∼400 GPa, which also causes the 300-K isotherm and Hugoniot to be virtually coincident in this pressure range. Above ∼400 GPa shock dissipation must go primarily into temperature, which is observed experimentally as a rapid increase in shock pressure above ∼400 GPa. The metallization of glassy Al₂O₃, if verified, is expected to be general in strong oxide insulators. Implications for Super Earths are discussed.     

Silver conductor fabrication by laser direct writing on Al<Subscript>2</Subscript>O<Subscript>3</Subscript> substrate

A novel technology for manufacturing circuitry, differing from conventional methods, called laser micro-cladding electronic pastes is presented. In this article, high-quality silver conductors were made on an Al₂O₃ substrate by this method. The process and corresponding mechanisms are described in detail. The experimental results show that the conductive lines produced have a minimum line width of 20 m, which is much smaller than the current limitations of conventional processes. The resistivity can reach the order of 10^-6 cm, which is the same level for pure bulk silver. Optical micrographs and SEM morphology observations were also carried out. PACS 81.15.Fg; 42.70.Hj; 42.62.-b; 42.62.Cf; 61.80.Ba     

Luminescence in collisions of low-energy ions with graphite and Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

Excitation of H⁺, H₂ ⁺, H₃ ⁺, He⁺, and Ar⁺ ions by impact on graphite and Al₂O₃ was investigated by means of emission spectroscopy in the 50–1000 eV energy range of the projectiles. Emission of Balmer series from excited neutral hydrogen is observed for both targets. In addition, for the Al₂O₃ target a continuum emission is observed. The continuum probably originates from excited M_nO_m molecules produced in the collision cascade, when surface atoms bound by ionic bonds are released after the bond breaking caused by neutralization. The spectra obtained under Ar⁺ -bombardment show Ar II lines emitted by backscattered ions.