Low-level measurements of actinides and long-lived radionuclides in biological and environmental samples

This paper describes a radiochemical method for the determination of⁹⁹Tc in large volumes of rain, river and seawater. The procedure is based on the reduction of technetium to the +4 oxidation state with potassium disulfite in a slightly acidic medium, followed by iron hydroxide precipitation. After oxidation to the +7 oxidation state, the technetium fraction is purified with iron hydroxide and calcium carbonate precipitations. Technetium (+7) is extracted with TBP (xylene) in 3M H₂SO₄, back extracted in 2M NaOH or ammonia, and the electrodeposition is made in 2M NaOH or H₂SO₄/NH₄OH medium at pH 5–6. The radiochemical yield is determined by gamma counting of the 140 keV gamma ray from⁹⁹Tc^m.⁹⁹Tc is counted on an anti-coincidence shielded GM-gas flow counter. The purity of the⁹⁹Tc plated samples is checked by alpha and beta spectrometry using surface barrier detectors and by gamma spectrometry on Ge(HP) detector. The radiochemical yield of 50–150 l water samples is around 20–60%.     

PIXE-RBS combination to measure uranium and thorium in environmental and biological samples

A combination of two techniques, PIXE (particle induced x-ray emission) and RBS (Rutherford backscattering), is proposed as an analytical tool to measure uranium and thorium in environmental and biological samples and in the study of the micro-distribution of uranium is low Z matrices such as biological tissue.Work supported by U.S. Department of Energy Contracts DE-AC02-76CH-00116 (MC, KWJ) and DE-AC02-76EV-00119 (NPS, MEW). One of us (ASP) is grateful to FINEP (Financiadora de Estudos e Projetos) and CNPq (Conselho Nacional de Desenvolvimento Cientifico e Technológico).     

Determination of actinides in environmental and biological samples using high-performance chelation ion chromatography coupled to sector-field inductively coupled plasma mass spectrometry

The combination of suppressed and non-suppressed cation-exchange chromatography with electrospray ionization mass spectrometry was demonstrated for the structural elucidation of unknown by-products (mostly quaternary ammonium compounds) in a new cholesterol-reducing drug. The suppressed mode using methanesulfonic acid and acetonitrile turned out to be unsuitable because of regenerant (tetrabutylammonium hydroxide) passing through the membrane of the suppressor into the eluent which led to a significant increase of spectral background in the mass spectrometer. Employing a mobile phase consisting of 200 mM formic acid and 60% (v/v) acetonitrile, the separation and detection of 8 unknown compounds was possible in the non-suppressed mode. The three most prominent compounds were selected for structural elucidation utilizing collision induced dissociation experiments. In a series of experiments the fragmentation behavior was investigated for different fragmentation voltages finally leading to structure proposals. Using gas chromatography hyphenated with mass spectrometry, additional information for the structure of the unknowns was collected and a possible way of their formation was proposed.     

Use of radiochemical methods as tools for speciation purposes in environmental and biological sciences.

Chemical speciation for a few elements can be facilitated to a great extent by incorporating a suitable radioisotope into the system and measuring the radiation of the isolated species. This radiospiking can be applied to in vitro and in vivo labelled experiments. Radionuclides are, however, also present as an anthropogenic contaminant from various nuclear fission activities. The radiotracer should be added under such conditions that it behaves in exactly the same way as the isotopes it represents. It should possess an adequate radioactive half-life, and preferably be a gamma-emitter because of the ease of detection. Radiotracer labelling is now widely used to study speciation problems of many essential and toxic elements in body fluids and tissues. It can be used to trace the different locations where the element is metabolized and stored, and subsequently to detect the element in the isolated biocomponents. The determination of the location of a radiotracer in a cell by autoradiography proved to be impractical because of the lack of resolution. Radiochemistry is similarly very useful for investigating particular aspects of the speciation of heavy metals as they occur in the ecosystem, and to follow the fate and effects of fission nuclides in the environment as they are carried around by the water and air masses. However, in certain circumstances the behaviour of fission products appears to be different from that of their stable analogues. For the actinides they simply do not exist. Radiochemical methods are a major tool for identifying and quantifying the nuclides in the different species.     

Analytical determination of actinides in environmental samples of the North Eastern Part of Poland

Low level alpha-spectrometry was applied for the determination of actinides separated from environmental samples. Interference free detection limits of 1.5–2.0 E-5 Bq at a counting interval of 150,000 sec and detection limits of the investigated samples of 0.05–0.005 Bq kg^–1 were determined.Presented; Actinides-89, September 24–29, 1989, Taschkent, USSR.     

Application of HPLC to measure vanadium in environmental,biological and clinical matrices

Vanadate and vanadium compounds exist in many environmental, biological and clinical matrices, and despite the need only limited progress has been made on the analysis of vanadium compounds. The vanadium coordination chemistry of different oxidation states is known, and the result of the characterization and speciation analysis depends on the subsequent chemistry and the methods of analysis. Many studies have used a range of methods for the characterization and determination of metal ions in a variety of materials. One successful technique is high performance liquid chromatography (HPLC) that has been used mainly for measuring total vanadium level and metal speciation. Some cases have been reported where complexes of different oxidation states of vanadium have been separated by HPLC. Specifically reversed phase (RP) HPLC has frequently been used for the measurement of vanadium. Other HPLC methods such as normal phase, anion-exchange, cation-exchange, size exclusion and other RP-HPLC modes such as, ion-pair and micellar have been used to separate selected vanadium compounds. We will present a review that summarizes and critically analyzes the reported methods for analysis of vanadium salts and vanadium compounds in different sample matrices. We will compare various HPLC methods and modes including sample preparation, chelating reagents, mobile phase and detection methods. The comparison will allow us to identify the best analytical HPLC method and mode for measuring vanadium levels and what information such methods provide with regard to speciation and quantitation of the vanadium compounds.     

Trends in liquid-phase microextraction, and its application to environmental and biological samples

Liquid phase microextraction (LPME) is a popular technique for sample pretreatment before the trace determination of target compounds from complex matrices, examples being pesticides in environmental and food samples, or drug residuals in biological samples such as blood or urine. LPME is simple, affordable, easy to operate, and highly sensitive. It is a miniaturized implementation of conventional liquid-liquid extraction in which only a few microliters of solvents are used instead of several hundreds of milliliters. This review focuses on newly developed LPME-based techniques, their application to environmental and biological samples, on their limitations, and on future applications.

Comparative studies of methylmercury determination in biological and environmental samples

Some parameters affecting the accuracy of various approaches to methylmercury (MeHg) determination in biological and environmental samples were studied. Different isolation techniques (ion-exchange, extraction, volatilization, distillation) and final measurement via cold vapour atomic absorption spectroscopy (CV AA) or gas chromatography (GC) were compared. Results obtained by the various isolation techniques are comparable for almost all biological and environmental samples, except for soils and some sediments, where disagreement between the results obtained by GC and CV AA was found. In order to resolve these problems, a new separation technique based on distillation of MeHg from the sample followed either by CV AA or GC was developed. The new method results in very good recovery and reproducibility (95 ± 2%) for all samples examined (fish, mussel, shrimp, blood, hair, algae, sediment, etc.), is specific for MeHg and provides for its differentiation from other species by an indirect CV AA determination. Gas-chromatographic measurement of the isolated MeHg using different packings and conditioning of the columns is also discussed. The distillation method with GC detection is advantageous in producing cleaner chromatograms and in prolonging the life-time of the packing and the intervals between reconditioning.     

同位素稀释电感耦合等离子体质谱测定环境和生物样品中的镉

应用同位素稀释电感耦合等离子体质谱（ID—ICP—MS）对环境和生物样品茶叶、湖沉积物和人发标准物质中的镉进行测定研究。对电感耦合等离子体质谱（ICP—MS）的工作条件和参数进行了最优化。讨论了多原子离子和同量异位素对镉同位素比值的影响,通过天然镉标准溶液对质量歧视进行了校正,并优化同位素稀释剂的加入量。将该方法应用于茶叶、人发和沉积物标准物质的测定。     

Spectrophotometric analysis of trichloroethylene in various environmental and biological samples

A simple sensitive extractive spectrophotometric method for determination of trichloroethylene is proposed. Trichloroethylene is treated with pyridine to form glutaconic aldehyde by heterolytic cleavage of the pyridine ring. Glutaconic aldehyde is further coupled with 4-aminoacetanilide to form an orange–red dye which is extractable in 3-methyl-1-butanol. The extracted dye shows absorption maximum at 520 nm. The system obeys Beer’s law in the range of 0.05–0.8 μg mL^?1. Important analytical parameters such as time, temperature, reagent concentration, acidity etc. have been optimized for complete colour reaction. Sandell’s sensitivity and molar absorptivity for the system were found to be 0.001 μg cm^?2 and 1.2 × 10⁵ L mol^?1 cm^?1, respectively. The proposed method is satisfactorily applied to micro-level determination of trichloroethylene in various environmental and biological samples.     

Rapid determination of actinides in seawater samples

A new rapid method for the determination of actinides in seawater samples has been developed at the Savannah River National Laboratory. The actinides can be measured by alpha spectrometry or inductively-coupled plasma mass spectrometry. The new method employs novel pre-concentration steps to collect the actinide isotopes quickly from 80 L or more of seawater. Actinides are co-precipitated using an iron hydroxide co-precipitation step enhanced with Ti⁺³ reductant, followed by lanthanum fluoride co-precipitation. Stacked TEVA Resin and TRU Resin cartridges are used to rapidly separate Pu, U, and Np isotopes from seawater samples. TEVA Resin and DGA Resin were used to separate and measure Pu, Am and Cm isotopes in seawater volumes up to 80 L. This robust method is ideal for emergency seawater samples following a radiological incident. It can also be used, however, for the routine analysis of seawater samples for oceanographic studies to enhance efficiency and productivity. In contrast, many current methods to determine actinides in seawater can take 1–2 weeks and provide chemical yields of ~30–60 %. This new sample preparation method can be performed in 4–8 h with tracer yields of ~85–95 %. By employing a rapid, robust sample preparation method with high chemical yields, less seawater is needed to achieve lower or comparable detection limits for actinide isotopes with less time and effort.     

Use of low-background instrumental neutron activation analysis to measure contaminants in silicon and biological samples

Instrumental Neutron Activation Analysis (INAA) is a common method of trace element analysis whose sensitivity is limited either by interference from other trace elements in the sample or by interference from ambient background radiation in the detection system. In at least two cases, a true low-background facility, such as that at Lawrence Berkeley National Laboratory, substantially enhances senitivity: (1) Ultra-pure silicon, such as that used in semiconductor fabrication. Even after prolonged exposure within a nuclear reactor, minimal observable gamma-ray emitting activities are produced in the silicon. Extrapolated from our 7 gram sample size experiments, parts-per-quadrillion (1.E-15) sensitivity to 23 elements should be obtainable for 400 gram sample sizes. (2) Similarly, the life elements H, C, N, O are effectively inert within the reactor, and this enhances sensitivity to trace elements in, for example, bacteria. Data will be presented for these two cases.     

Handling of environmental and biological samples via pre-column technologies

Sample handling is still a weak point in chromatography and in analytical chemistry in general. One consideration is the automation potential of new procedures. Solid-liquid extraction techniques in combination with pre-column technology are particularly promising in this regards. The construction and geometry of pre-columns both for conventional and narrow-bore HPLC are of major importance, since band broadening should be kept at a minimum for an optimal functioning of the analytical system. The various operations that can be carried out with such a pre-column are trace-enrichment, clean-up of the sample which depends on the type of adsorbents used in the precolumn, i.e., polar or apolar materials, ion exchangers or metal covered surfaces, etc., protection of the analytical column, field sampling and storage of samples and as a substrate for on-column chemical derivatizations. These various operations are demonstrated with practical examples from the fields of environmental and biological analysis. The selectivity can be further enhanced by coupling pre-column technology with selective detection models such as diode array UV, electrochemical or fluorescence detection. This enables the construction of optimal and integrated analysis systems which are fully automated and microprocessor controlled. They can also be made compatible with miniaturized LC-technology.     

Rapid determination of actinides in asphalt samples

A new rapid method for the determination of actinides in asphalt samples has been developed that can be used in emergency response situations or for routine analysis. If a radiological dispersive device, improvised nuclear device or a nuclear accident such as the accident at the Fukushima Nuclear Power Plant in March, 2011 occurs, there will be an urgent need for rapid analyses of many different environmental matrices, including asphalt materials, to support dose mitigation and environmental clean-up. The new method for the determination of actinides in asphalt utilizes a rapid furnace step to destroy bitumen and organics present in the asphalt and sodium hydroxide fusion to digest the remaining sample. Sample preconcentration steps are used to collect the actinides and a new stacked TRU Resin + DGA Resin column method is employed to separate the actinide isotopes in the asphalt samples. The TRU Resin plus DGA Resin separation approach, which allows sequential separation of plutonium, uranium, americium and curium isotopes in asphalt samples, can be applied to soil samples as well.     

Simultaneous determination of plutonium and americium in biological and environmental samples

A radiochemical method is given to determine the specific activity of²³⁸Pu, and²⁴¹Am from the global fallout in environmental and biological samples. The radiochemical recovery was for human livers Pu: 60–70%, Am: 40–60%; Bran: Pu: 50–70%, Am: 30–40%; Soil: Pu: 50–80%, Am: 30–50%. The resolution of the alpha-spectrum was for soils 30–40 keV and for livers and brans 40–60 KeV. To facilitate the wet ashing of large amounts of bran (15 kg), which are necessary to determine the presently very small activity concentrations of the transuranic elements in these types of samples, a fermentation process was employed. The procedure was tested by using NBS standard reference material and subsequently applied for the determination of Pu and Am from the global fallout in livers, plant tissues (bran), and soils.     

Determination and lebels of99Tc in environmental and biological samples

In this paper, the physical and chemical methods used in our laboratory for the measurement of⁹⁹Tc in natural samples are reviewed. Levels of⁹⁹Tc in rainwater, algae, and freshwater samples are given. In addition, and estimation of the radiological impact of⁹⁹Tc to the population, derived from our earliear atmospheric⁹⁹Tc measurements, is presented. For rainwater, levels of¹³⁷Cs are also given for comparison.Work partially supported by the contract PB86-0207 of the Spanish CICYT.     

Rapid separation of actinides and radiostrontium in vegetation samples

A new rapid method for the determination of actinides and radiostrontium in vegetation samples has been developed at the Savannah River Site Environmental Lab (Aiken, SC, USA) that can be used in emergency response situations or for routine analysis. The actinides in vegetation method utilizes a rapid sodium hydroxide fusion method, a lanthanum fluoride matrix removal step, and a streamlined column separation process with stacked TEVA, TRU and DGA Resin cartridges. Lanthanum was separated rapidly and effectively from Am and Cm on DGA Resin. Alpha emitters are prepared using rare earth microprecipitation for counting by alpha spectrometry. The purified ⁹⁰Sr fractions are mounted directly on planchets and counted by gas flow proportional counting. The method showed high chemical recoveries and effective removal of interferences. The actinide and ⁹⁰Sr in vegetation sample analysis can be performed in less than 8 h with excellent quality for emergency samples. The rapid fusion technique is a rugged sample digestion method that ensures that any refractory actinide particles or vegetation residue after furnace heating is effectively digested.     

Electrochemical sensor for estriol hormone detection in biological and environmental samples

A stable conducting film for sensing using reduced graphene oxide (RGO), gold nanoparticles (GNPs), and potato starch (PS) is proposed. The characterization of the nanomaterials was obtained by ultraviolet and visible spectroscopy, dynamic light scattering, zeta potential, Fourier transform infrared spectroscopy, atomic force microscopy, and cyclic voltammetry. The voltammetric behavior of the RGO-GNPs-PS/GCE electrodes was studied in the presence of estriol and the results showed a high anodic peak current at 0.64 V. Under optimal conditions, an analytical curve was obtained, in which the anodic peak estriol was linear in the range from 1.5 to 22 μmol L^?1, with a detection limit of 0.48 μmol L^?1. The modified electrodes were applied for determination of estriol in environmental and biological samples. The proposed electrode was used for estriol determination in water and urine samples, which presented a recovery range from 92.1 to 106%, showing that RGO-GNPs-PS/GCE is a viable alternative for the detection of estriol and can be attractive for several electrochemical applications.