Effect of amino and polysiloxane groups on the chemical adsorption of polymers containing thiophosphate at the oil/metal interface under extreme pressure

Copolymers that separately contained thiophosphate–polysiloxane, thiophosphate–amino, and thiophosphate–polysiloxane–amino groups were synthesized and characterized. The performances of these synthesized copolymers on metal surfaces under a high load and rotary velocity were examined by the measurement of the oil temperature, frictional coefficient, and electrical contact resistance between two metal surfaces. The configuration of the adsorption layer was studied with energy‐dispersive spectrometry (EDS) and scanning electron microscopy (SEM). Copolymers that contained amino–thiophosphate groups reduced the frictional coefficient between two metal surfaces and markedly limit the increase in the oil temperature. Notably, a higher content of polysiloxane groups in the copolymer corresponded to an increased operating time to establish the adsorption layer on the metal surface. However, a higher content of amino groups reduced the time required for the layer to form. The adsorption layers that formed on the metal surfaces were investigated by EDS as phosphides produced by a chemical reaction of the thiophosphate‐containing copolymer with the metal surface. These adsorption layers on the metal surface were directly observed with SEM. The layer that formed on the metal surface of copolymers containing less polysiloxane and more amino groups was the thickest layer for all the synthesized copolymers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1795–1803, 2002     

Hyperbranched‐polyethyleneiminated functional polymers. III. Synthesizing thiophosphate‐containing pseudodendritic poly‐ethyleneiminated polyoxypropylenediamine and its behavior at an oil/metal interface under extreme pressure

A simple synthetic route for preparing a thiophosphate‐containing pseudodendritic polyethyleneiminated polyoxypropylenediamine, D400(EI)_xP, is presented. The number of ethyleneimine group (EI) in D400(EI)_xP was determined by ¹H‐ and ¹³C‐NMR to be 4.3 for D400(EI)₄P and 8.9 for D400(EI)₈P, and the extent of branch was quantitatively determined using potentiometric titration. The numbers of thiophosphate groups per thiophosphate‐containing pseudodendritic polymers molecule for D400(EI)₀P, D400(EI)₄P, and D400(EI)₈P were calculated by elemental analyses of sulfur content. The AW performance of these synthesized thiophosphate‐containing pseudodendritic polymers was examined by measuring the temperature of oil, and the frictional coefficient and electrical contact resistance between the two metal surfaces. More thiophosphate groups on either side of D400(EI)₈P are found to increase the electrical contact resistance due to the chemical adsorption of thiophosphate groups onto metal surfaces, forming a thick layer and reducing operating time required to form the adsorption layer. Interestingly, the adsorption layers markedly reduce the frictional coefficient (～ 0.012) and limit the increase in oil temperature (～ 90 °C) throughout the entire period of AW test, reducing weight loss of the metal (0.1 mg). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5504–5513, 2004     

Stable heterocumulene monomer in water; Synthesis and polymerization of (meth)acrylates having an isothiocyanate structure

Novel methacrylate and acrylate monomers having an isothiocyanate structure, 2‐isothiocyanatoethyl methacrylate (ITEMA) and 2‐isothiocyanatoethyl acrylate (ITEA), were synthesized, and their radical polymerizations were examined, respectively. ITEMA and ITEA were synthesized by addition of carbon disulfide to 2‐aminoethyl methacryrate or 2‐aminoethyl acrylate, followed by treatment with ethyl chloroformate. Radical polymerizations of the obtained monomers ( ITEMA , ITEA ) were carried out methyl ethyl ketone using 2,2'‐azobisisobutyronitrile (AIBN) as an initiator to obtain the corresponding polymers. The glass transition temperatures of the poly‐ITEMA and poly‐ITEA were determined to be 55 and 2 °C by differential scanning calorimetry, respectively. The 5 wt % decomposition temperatures of the poly‐ITEMA and poly‐ITEA were determined to be 277 and 269 °C by thermogravimetric analysis, respectively. Isothiocyanato groups in the monomers did not react with water in acetone solution at 60 °C for 24 h to be tolerable to water. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4522–4529     

A straightforward strategy for the efficient synthesis of acrylate and phosphine oxide‐containing vegetable oils and their crosslinked materials

Phosphorus‐containing triglycerides were prepared from a new route that involves the singlet oxygen photo‐oxygenation of high oleic sunflower oil and further reduction of the resulting hydroperoxide derivatives to a mixture of secondary allylic alcohols. These allylic alcohols in presence of chlorodiphenylphosphine give allylic phosphinites capable to undergo a [2,3]‐sigmatropic rearrangement leading to tertiary phosphine oxides directly linked to triglyceride in a one‐pot two‐step reaction. The obtained phosphorus‐containing triglycerides with different hydroxyl content were activated to polymerization by acrylation and these acrylate triglycerides were radically crosslinked in presence of different amounts of pentaerythritol tetra‐acrylate. The thermal, dynamic‐mechanical, and flame retardancy properties of the final materials were evaluated. Thermal and thermo‐oxidative degradation was studied by gas chromatography/mass spectrometry, ³¹P HR‐MAS NMR spectroscopy, and scanning electron microscopy. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4051–4063, 2009     

Aryl acrylate based high‐internal‐phase emulsions as precursors for reactive monolithic polymer supports

Water‐in‐oil high‐internal‐phase emulsions (HIPEs), containing 4‐nitrophenyl acrylate and 2,4,6‐trichlorophenyl acrylate as reactive monomers, were prepared and polymerized, and highly porous monolithic materials resulted. The novel materials were studied by combustion analysis, Fourier transform infrared spectroscopy scanning electron microscopy, mercury porosimetry, and N₂ adsorption/desorption analysis. With both esters, cellular macroporous monolithic polymers were obtained; the use of 4‐nitrophenyl acrylate resulted in a cellular material with void diameters between 3 and 7 μm and approximately 3‐μm interconnects, whereas the use of 2,4,6‐trichlorophenyl acrylate yielded a foam with void diameters between 2 and 5 μm, most interconnects being around 1 μm. The resulting monoliths proved to be very reactive toward nucleophiles, and possibilities of functionalizing the novel polymer supports were demonstrated via reactions with amines bearing additional functional groups and via the synthesis of an acid chloride derivative. Tris(hydroxymethyl)aminomethane and tris(2‐aminoethyl)amine derivatives were obtained. The hydrolysis of 4‐nitrophenylacrylate removed the nitrophenyl group, yielding a monolithic acrylic acid polymer. Furthermore, functionalization to immobilized acid chloride was performed very efficiently, with more than 95% of the acid groups reacting. The measurement of the nitrogen content in 4‐nitrophenyl acrylate poly(HIPE)s after various times of hydrolysis showed the influence of the total pore volume of the monolithic polymers on the velocity of the reaction, which was faster with the more porous polymer. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 296–303, 2005     

Stimulus‐responsive polymers based on 2‐hydroxypropyl acrylate prepared by RAFT polymerization

Homopolymerization and diblock copolymerization of 2‐hydroxypropyl acrylate (HPA) has been conducted using reversible addition fragmentation chain transfer (RAFT) chemistry in tert‐butanol at 80 °C. PHPA homopolymers were obtained with high conversions and narrow molecular weight distributions over a wide range of target degrees of polymerization. Like its poly(2‐hydroxyethyl methacrylate) isomer, PHPA homopolymer exhibits inverse temperature solubility in dilute aqueous solution, with cloud points increasing systematically on lowering the mean chain length. The nature of the end groups is shown to significantly affect the cloud point, whereas no effect of concentration was observed over the PHPA concentration range investigated. Various thermoresponsive PHPA‐based diblock copolymers were prepared via one‐pot syntheses in which the second block was either permanently hydrophilic or pH‐responsive. Preliminary studies confirmed that poly(ethylene oxide)‐poly(2‐hydroxypropyl acrylate) (PEO₄₅‐PHPA₄₈) and poly(2‐hydroxypropyl acrylate)‐ poly(2‐hydroxyethyl acrylate) (PHPA₄₉‐PHEA₆₈)diblock copolymers formed well‐defined PHPA‐core micelles in 10 mM sodium nitrate solution at 40 °C and 70 °C with mean hydrodynamic diameters of 20 nm and 35 nm, respectively. In contrast, most other PHPA‐based diblock copolymers investigated formed larger colloidal aggregates in 10 mM NaNO₃ solution at elevated temperatures. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2032–2043, 2010     

Synthesis and properties of fluorine‐containing poly(aryl ether oxadiazole)s

Fluorine‐containing poly(aryl ether 1,3,4‐ozadiazole)s were synthesized by the nucleophilic aromatic substitution reaction of 2,5‐bis(2,3,4,5,6‐pentafluorophenyl)‐1,3,4‐oxadiazole and various bisphenols in the presence of potassium carbonate. The polymerizations were carried out at 30 °C in 1‐methyl‐2‐pyrrolidinone to avoid the gelation caused by a crosslinking reaction at para and ortho carbons to the 1,3,4‐oxidiazole ring. The obtained polymers were all para‐connected linear structures. The obtained fluorine‐containing poly(aryl ether 1,3,4‐ozadiazole)s showed excellent solubility and afforded tough, transparent films by the solution‐casting method. They also exhibited a high glass transition temperature depending on the molecular structure, and the glass transition temperature could be controlled by the bisphenols in the range of 157–257 °C. They showed good thermal stability and excellent hydrophobicity due to the incorporation of the 2,3,5,6‐tetrafluoro‐1,4‐phenylene moiety. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2855–2866, 2007     

Synthesis of poly(p‐phenylene sulfide) from bis(4‐bromophenyl) disulfide

Improved reaction conditions for the preparation of poly(p‐phenylene sulfide) (PPS) directly from bis(4‐bromophenyl) disulfide (BBD) have been established. Heating BBD with magnesium metal afforded only a low molecular weight polymer. PPS with a melting temperature around 280 °C was obtained from BBD in the presence of sodium carbonate or zinc metal. The best results were obtained with the addition of a catalytic amount of KI to the zinc–BBD mixture. Polymers prepared by the above methods are semicrystalline and dissolve in 1‐chloronaphthalene and have properties comparable to commercial PPS. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 900–904, 2006     

Effect of the structure of amphiphilic poly(ethylene glycol)‐containing graft copolymers on styrene emulsion polymerization

Amphiphilic graft copolymers consisting of monomeric units of poly(ethylene glycol) monomethyl ether acrylate, lauryl or stearyl methacrylate, and 2‐hydroxyethyl methacrylate were synthesized and characterized. The effectiveness of these poly(ethylene glycol)‐containing graft copolymers in stabilizing styrene emulsion polymerization was evaluated. The polymerization rate (R_p) increases with increasing graft copolymer concentration, initiator concentration, or temperature. At a constant graft copolymer concentration, R_p increases, and the amount of coagulum decreases with the increasing hydrophilicity of graft copolymers. The polymerization system does not follow Smith–Ewart case II kinetics. The desorption of free radicals out of latex particles plays an important role in the polymerization kinetics. The overall activation energy and the activation energy for the radical desorption process are 85.4 and 34.3 kJ/mol, respectively. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1608–1624, 2002     

Synthesis,photoluminescence, and electrochromism of novel aromatic poly(amine‐1,3,4‐oxadiazole)s bearing anthrylamine chromophores

Two novel poly(amine‐hydrazide)s were prepared from the polycondensation reactions of the dicarboxylic acid, 9‐[N,N‐di(4‐carboxyphenyl)amino]anthracene ( 1 ), with terephthalic dihydrazide ( TPH ) and isophthalic dihydrazide ( IPH ) via the Yamazaki phosphorylation reaction, respectively. The poly(amine‐hydrazide)s were readily soluble in many common organic solvents and could be solution cast into transparent films. Differential scanning calorimetry (DSC) indicated that these hydrazide polymers had glass‐transition temperatures (T_g) in the range of 182–230 °C and could be thermally cyclodehydrated into the corresponding oxadiazole polymers in the range of 300–400 °C. The resulting poly(amine‐1,3,4‐oxadiazole)s had useful levels of thermal stability associated with high T_g (263–318 °C), 10% weight‐loss temperatures in excess of 500 °C, and char yield at 800 °C in nitrogen higher than 55%. These organo‐soluble anthrylamine‐based poly(amine‐hydrazide)s and poly (amine‐1,3,4‐oxadiazole)s exhibited maximum UV‐vis absorption at 346–349 and 379–388 nm in N‐methyl‐2‐pyrrolidone (NMP) solution, respectively. Their photoluminescence spectra in NMP solution showed maximum bands around 490–497 nm in the green region. The poly(amine‐hydrazide) I ‐ IPH showed a green photoluminescence at 490 nm with PL quantum yield of 29.9% and 17.0% in NMP solution and film state, respectively. The anthrylamine‐based poly(amine‐1,3,4‐oxadiazole)s revealed a electrochromic characteristics with changing color from the pale yellow neutral form to the red reduced form when scanning potentials negatively from 0.00 to ?2.20 V. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1584–1594, 2009     

Synthesis of a new type of core–shell particle from hyperbranched polyglycerol

Based on hyperbranched polyglycerol (PG), a route to prepare particles with a novel topology was developed. The hydroxyls of PG were converted to trithiocarbonates, and the latter were used to mediate the surface graft polymerization of N,N‐dimethylaminoethyl acrylate. The poly(N,N‐dimethylaminoethyl acrylate) shell was crosslinked by 1,6‐dibromohexane and then parted from the core by the cleavage of trithiocarbonates with sodium borohydride. Novel particles with thiol groups located on the interface between the PG core and poly(N,N‐dimethylaminoethyl acrylate) shell were thus formed. The shell crosslinking could be performed at very high solid contents (2–4%). These polymer particles showed pH‐ and temperature‐dependent solubility. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5458–5464, 2005     

Crosslinking of chlorine‐containing polymers by dicyclopentadiene dicarboxylic salts

Alkali‐ and alkali‐earth‐metal salts of dicyclopentadiene dicarboxylic acid (DCPDCA) were prepared and employed as crosslinkers for chlorine‐containing polymers such as polychloromethylstyrene (PCMS), chlorinated polypropylene (CPP), polyepichlorohydrin (PECH), and poly(vinyl chloride) (PVC). Thermally reversible covalent crosslinks (i.e.,  DCPD bridges) between polymer chains were generated through esterification between the chlorine–carbon bonds of the polymer and the carboxylic salt groups of the crosslinker. The crosslinking reactivity decreased in the following sequence: K > Na > LiDCPDCA > alkali‐earth‐metal salts of DCPDCA. In addition, PCMS and CPP had higher gelation rates than PECH and PVC. Good flowability at about 195 °C and solubility in maleimide‐containing dichlorobenzene on heating indicated that the crosslinked PCMS and CPP exhibited thermally reversible crosslinking because of dimer/monomer (cyclopentadiene) conversion of  DCPD moieties via reversible Diels–Alder cycloaddition. Samples of PECH and PVC crosslinked by the alkali salts of DCPDCA were insoluble even when heated in maleimide‐containing dichlorobenzene. However, these crosslinked polymers could be dissolved partially after the same treatment when the crosslinker was an alkali‐earth‐metal salt of DCPDCA. Thermal degradation such as dehydrochlorination of the PECH and PVC might have been responsible for uncontrolled crosslinking because these two polymers are known to be thermally unstable. The unreacted COOK, COONa, or COOLi of the crosslinkers might have initiated base‐induced dehydrochlorination when PECH and PVC were heated at high temperatures. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 818–825, 2000     

Synthesis,characterization, and electroluminescence properties of poly(fluorenevinylene benzobisthiazoles)

A series of vinylene‐linked copolymers based on electron‐deficient benzobisthiazole and electron‐rich fluorene moieties were synthesized via Horner–Wadsworth–Emmons polymerization. Three different polymers P1 , P2 , and P3 , were prepared bearing octyl, 3,7‐dimethyloctyl, and 2‐(2‐ethoxy)ethoxyethyl side chains, respectively. The polymers all possessed moderate molecular weights, good solubility in aprotic organic solvents, and high fluorescence quantum efficiencies in dilute solutions. P2 , which bore branched 3,7‐dimethyloctyl side chains, exhibited better solubility than the other polymers, but also exhibited the lowest thermal decomposition temperature of all polymers. Overall, the impact of the side chains on the polymers optical properties in solution was negligible as all three polymers gave similar absorption and emission spectra in both solution and film. Guest‐host light‐emitting diodes using dilute blends of the polymers in a poly(N‐vinylcarbazole) host gave blue‐green emission with P2 exhibiting the highest luminous efficiency, 0.61 Cd/A at ～500 nm. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

New ladder‐type conjugated polymer with broad absorption,high thermal stability,and low band gap

New ladder‐type π‐conjugated polymer poly{6‐alkyl‐pyrrolo[3,2‐b:4,5‐b′]bis‐[1,4]benzothiazine} ( PPBBTZ ) was synthesized through a simple method. PPBBTZ showed good solubility in organic solvents (such as chloroform, tetrahydrofuran, chlorobenzene, o‐dichlorobenzene) and high thermal stability (decomposition temperatures up to 323 °C and 299 °C in nitrogen and air, respectively). The highest occupied molecular orbital and lowest unoccupied molecular orbital energy level estimated from electrochemistry result and absorption spectrum were ?5.46 and ?3.81 eV, respectively, with a band gap of 1.65 eV. More interestingly, PPBBTZ displayed broad absorption from ultraviolet to visible light regions (200–750 nm). These properties suggested PPBBTZ was a good candidate in opto‐electronics. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Controlled synthesis of hydrophilic concentrated polymer brushes and their friction/lubrication properties in aqueous solutions

Polymer brushes of water‐soluble polymers, poly(2‐hydroxyethyl acrylate) (PHEA) and poly(poly(oxyethyleneglycol)methylether acrylate) (PPEGA), were synthesized on a silicon wafer and a silica particle by applying photo‐induced organotellurium‐mediated radical polymerization to surface‐initiated graft polymerization. High graft densities were obtained, corresponding to reduced graft densities of about 0.32 and 0.42 for the PHEA and PPEGA brushes, respectively. These values were high enough to be categorized in the regime of “concentrated” polymer brushes (CPBs). Atomic force microscopic (AFM) study revealed that the CPB of PPEGA was allowed to be highly swollen in water but the CPB of PHEA did not. This means that water is reasonably good for PPEGA but not for PHEA. The AFM microtribological study between swollen brushes revealed two lubrication regimes, namely, boundary‐ and hydrodynamic‐lubrication regimes, with different shear‐velocity dependencies. Reflecting insufficient quality of water as a solvent, the CPB of PHEA showed adhesive interaction and thereby a higher frictional coefficient μ in the boundary lubrication. More interestingly, super lubrication was achieved for the CPB of PPEGA with a μ value in the order of 10^?4 in water and in 0.1 M aqueous NaCl solution (without the help of electrostatic repulsion). Super lubrication was concluded to be a characteristic feature of the CPB, even in an aqueous system. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Preparation and properties of novel low dielectric constant benzoxazole‐based polybenzoxazine

A novel benzoxazine monomer containing a benzoxazole group was synthesized using a nonsolvent method and then named DAROH‐a. The structure of DAROH‐a was confirmed by FTIR, ¹H NMR, elemental analysis, and mass spectrometry. The curing reaction activation energy was calculated at 140 kJ/mol. Its corresponding crosslinked polybenzoxazines, poly(DAROH‐a), displayed a higher glass transition temperature at 402 °C, a 9% weight loss at the said temperature, and a high char yield of 42 wt % (800 °C, in nitrogen). Moreover, the dielectric constants of poly(DAROH‐a) were low and changed only slightly at different temperatures. Furthermore, the dielectric constants and dielectric loss of poly(DAROH‐a) at the same frequency barely changed from room temperature to 150 °C. The photophysical properties of poly(DAROH‐a) film were also investigated. Poly(DAROH‐a) showed an absorption peak at 280 nm. The photoluminescent emission spectrum of poly(DAROH‐a) film displayed predominant emission peaks at 521 nm. It might have potential application as high‐performance materials because of its excellent dielectric constants stability and thermal stability under high temperature. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of di‐ and tri‐tertiary amine containing methacrylic monomers and their (co)polymerization via RAFT

The synthesis, reversible addition‐fragmentation chain transfer (RAFT) (co)polymerization, and aqueous phase behavior of three methacrylic monomers containing two or three pendent tertiary amine functional groups are described. Homopolymerizations were conducted with 1‐methyl‐1‐cyanoethyl dithiobenzoate (CPDB) under bulk conditions following standard RAFT procedures. All three monomers, 1,3‐bis(dimethylamino)propan‐2‐yl methacrylate ( M1 ), 1‐(bis(3‐(dimethylamino)propyl) amino)propan‐2‐yl methacrylate ( M2 ), and 2‐((2‐(2‐(dimethylamino)ethoxy)ethyl) methylamino)ethyl acrylate ( M3 ), polymerized in a controlled manner as evidenced by the kinetic and molecular weight profiles. Homopolymerizations conducted at a lower ratio of CPDB:AIBN proceeded faster than those at a higher ratio. Subsequently, the facile copolymerization behavior of M1 and M3 was demonstrated via the synthesis of a range of statistical copolymers with hexyl and lauryl methacrylate comonomers containing 10–90 mol % hydrophobic comonomer. Finally, the aqueous‐solution characteristics of the M1 – M3 homopolymers were briefly examined. All three homopolymers were shown to undergo phase transitions in aqueous media in response to changes in both temperature and pH. Specifically, 1 wt % solutions of poly M1 were shown to possess an LCST of ～22 °C, that of poly M2 at ～33 °C, and for poly M3 the observed cloud point was ～63 °C. Additionally, all homopolymers became hydrophobic and phase separated at high solution pH. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1877–1890, 2009     

Silole‐containing poly(silylenevinylene)s: Synthesis,characterization, aggregation‐enhanced emission,and explosive detection

Hydrosilylation polymerizations of 1,1‐dimethyl‐2,5‐bis(4‐ethynylphenyl)‐3,4‐diphenylsilole with aromatic silylhydrides including 1,4‐bis(dimethylsilyl)benzene, 4,4′‐bis(dimethylsilyl)biphenyl, 2,5‐bis(dimethylsilyl)thiophene, and 2,7‐bis(dimethylsilyl)‐9,9‐dihexylfluorene in the presence of Rh(PPh₃)₃Cl catalyst in refluxed tetrahydrofuran afford a series of silole‐containing poly(silylenevinylene)s. Under optimum condition, the alkyne polyhydrosilylation reactions progress efficiently and regioselectively, yielding polymers with high molecular weights (M_w up to 95,300) and good stereoregularity (E content close to 99%) in high yields (up to 92%). The polymers are processable and thermally stable, with high decomposition temperatures in the range of 420?449 °C corresponding to 5% weight loss. They are weakly fluorescent in the solution state but become emissive in the aggregate and film states, demonstrating their aggregation‐enhanced emission characteristics. The explosive sensing capabilities of the polymers are examined in both solution and aggregate states. The emissions of the polymers aggregates in aqueous mixture are quenched more efficiently by picric acid in an exponential pattern with high quenching constants (up to 27,949 L mol^?1), suggesting that the polymers aggregates are sensitive chemosensors for explosive detection. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Diblock copolymers,micelles, and shell‐crosslinked nanoparticles containing poly(4‐fluorostyrene): Tools for detailed analyses of nanostructured materials

Amphiphilic core–shell nanostructures containing ¹⁹F stable isotopic labels located regioselectively within the core domain were prepared by a combination of atom transfer radical polymerization (ATRP), supramolecular assembly, and condensation‐based crosslinking. Homopolymers and diblock copolymers containing 4‐fluorostyrene and methyl acrylate were prepared by ATRP, hydrolyzed, assembled into micelles, and converted into shell‐crosslinked nanoparticles (SCKs) by covalent stabilization of the acrylic acid residues in the shell. The ATRP‐based polymerizations, producing the homopolymers and diblock copolymers, were initiated by (1‐bromoethyl)benzene in the presence of CuBr metal and employed N,N,N′,N″,N″‐pentamethyldiethylenetriamine as the coordinating ligand for controlled polymerizations at 75–90 °C for 1–3 h. Number‐average molecular weights ranged from 2000 to 60,000 Da, and molecular weight distributions, generally less than 1.1 and 1.2, were achieved for the homopolymers and diblock copolymers, respectively. Methyl acrylate conversions as high as 70% were possible, without observable chain–chain coupling reactions or molecular weight distribution broadening, when bromoalkyl‐terminated poly(4‐fluorostyrene) was used as the macroinitiator. Poly(4‐fluorostyrene), incorporated as the second segment in the diblock copolymer synthesis, was initiated from a bromoalkyl‐terminated poly(methyl acrylate) macroinitiator. After hydrolysis of the poly(methyl acrylate) block segments, micelles were formed from the resulting amphiphilic block copolymers in aqueous solutions and were then stabilized by covalent intramicellar crosslinking throughout the poly(acrylic acid) shells to yield SCKs. The SCK nanostructures on solid substrates were visualized by atomic force microscopy and transmission electron microscopy. Dynamic light scattering was used to probe the effects of crosslinking on the resulting hydrodynamic diameters of nanoparticles in aqueous and buffered solutions. The presence of fluorine atoms in the diblock copolymers and resulting SCK nanostructures allowed for characterization by ¹⁹F NMR in addition to ¹H NMR, ¹³C NMR, and IR spectroscopy. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4152–4166, 2001     

Linear poly(amide triazole)s derived from d‐glucose

The click reaction between azides and alkynes is been increasingly employed in the preparation of polymers. In this article, we describe the synthesis and click polyaddition reaction of a new A‐B‐type amide monomer—prepared from d ‐glucose as renewable resource—containing the alkyne and azide functions. Both Cu(I)‐catalyzed and metal‐free click polymerization methods were used to prepare glucose‐derived poly(amide triazole)s. The resulting polymers had weight‐average molecular weights in the 45,000–129,000 range and were characterized by GPC, IR, and NMR spectroscopies. Thermal and X‐ray diffraction studies revealed them to be amorphous. Their qualitative solubilities in various solvents and their water sorption have been studied. The poly(amide triazole)s having the alcohol functions protected as methyl ether were water‐soluble. The presence of the amide functions along the polymer chain made these polytriazoles degradable in the presence of sodium deuteroxide. The degradation was monitored by NMR analysis, and the degradation product was characterized by HRMS. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 629–638