Enhancing the electroluminescent efficiency of poly{5‐methoxy‐2‐[(2′‐ethyl‐hexyl)‐oxy]‐p‐phenylenevinylene}/poly(2,3‐diphenyl‐5‐octyl‐p‐phenylenevinylene) polyblends by the introduction of chemical bonding through a thermal treatment

A significant improvement in the electroluminescence (EL) properties was observed for a poly{5‐methoxy‐2‐[(2′‐ethyl‐hexyl)‐oxy]‐p‐phenylenevinylene} (MEH–PPV)/poly(2,3‐diphenyl‐5‐octyl‐p‐phenylenevinylene) (DPO–PPV) blend after a thermal treatment at 200 °C for 2 h in vacuo to furnish the chemical bonding between polymer chains. ¹H NMR spectroscopy and two‐photon excitation microscopy revealed that the chemical bonding turned the immiscible polyblend into a system more like a block copolymer with a vertically segregated morphology. Because both the lowest unoccupied molecular orbital and highest occupied molecular orbital levels of MEH–PPV in the wetting layer were higher than those of DPO–PPV in the upper layer, the heterojunction between the two layers of the polymers fit the category of so‐called type II heterojunctions. As a result, the turn‐on voltage of the polymer light‐emitting diode prepared with the thermally treated polyblend decreased to ～0.6 V, and the EL emission intensities and quantum efficiencies increased to about 4 times those of the untreated polyblend. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 62–69, 2006     

High‐quality poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐p‐phenylenevinylene] synthesized by a solid–liquid two‐phase reaction: Characterizations and electroluminescence properties

Poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐p‐phenylenevinylene] (MEH‐PPV) with a molar mass of 26–47 × 10⁴ g mol^?1 and a polydispersity of 2.5–3.2 was synthesized by a liquid–solid two‐phase reaction. The liquid phase was tetrahydrofuran (THF) containing 1,4‐bis(chloromethyl)‐2‐methoxy‐5‐(2′‐ethylhexyloxy)benzene as the monomer and a certain amount of tetrabutylammonium bromide as a phase‐transfer catalyst. The solid phase consisted of potassium hydroxide particles with diameters smaller than 0.5 mm. The reaction was carried out at a low temperature of 0 °C and under nitrogen protection. No gelation was observed during the polymerization process, and the polymer was soluble in the usual organic solvents, such as chloroform, toluene, THF, and xylene. A polymer light‐emitting diode was fabricated with MEH‐PPV as an active luminescent layer. The device had an indium tin oxide/poly(3,4‐ethylenedioxylthiophene) (PEDOT)/MEH‐PPV/Ba/Al configuration. It showed a turn‐on voltage of 3.3 V, a luminescence intensity at 6.1 V of 550 cd/m², a luminescence efficiency of 0.43 cd/A, and a quantum efficiency of 0.57%. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3049–3054, 2004     

Versatile route for tuning optical properties of poly(2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene)

In this contribution, we report a versatile method for tuning optical properties of poly(2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene) (MEH‐PPV) in its solution with 1,2‐dichloroethane, accomplished by reacting with pyridinium formate (PF), a volatile organic salt. We can systematically control the positions of absorption and photoluminescent (PL) spectra of MEH‐PPV by adjusting the concentration of PF in the solution. The addition of 10 vol % PF caused a blue‐shift in the absorption spectra by about 65 nm. When the concentration of PF decreased to 0.1 vol %, the blue‐shift occurred to a lesser extent, about 25 nm. The measurements of PL spectra showed similar behaviors. The λ_max shifted from 558 nm to 546 and 552 nm when 10 and 0.1 vol % of PF were added, respectively. The changes of PL colors from orange to yellow and green, respectively, were observed by naked eyes. Structural investigation by nuclear magnetic resonance and Fourier‐transformed infrared spectroscopy indicated that the changes of the optical properties were due to chemical modifications along the main chain and the side groups of MEH‐PPV. These results implied a simple route for engineering the HOMO–LUMO energy gap of MEH‐PPV, which could be utilized in advanced applications such as organic light‐emitting devices and solar cells. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 696–705, 2009     

Comparative study of the optical,electrochemical, electrolumiscent,and photovoltaic properties of dendritic pendants modified poly(p‐phenylene vinylene)s

In this study, the optical, electrochemical, electrolumiscent, and photovoltaic properties of a series of poly(p‐phenylene vinylene) (PPV) derivatives bearing different dendritic pendants, poly{2‐[3′,5′‐bis(2″‐ethylhexyloxy)benzyloxy]‐1,4‐phenylenevinylene} (BE‐PPV), poly{2‐[2′,5′‐bis(3″,7″‐dimethyl)octyloxy]‐1,4‐phenylenevinylene} (BD‐PPV), poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV), poly{2‐[3′,5′‐bis(2″‐ethylhexyloxy)benzyloxy]‐1,4‐phenylenevinylene}‐co‐poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene] (BE‐co‐MEH‐PPV), and poly{2‐[2′,5′‐bis(3″,7″‐dimethyl)octyloxy]‐1,4‐phenylenevinylene}‐co‐poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylenevinylene] (BD‐co‐MDMO‐PPV), were investigated. The steric pendants strongly affect the absorption spectra, photoluminescence (PL) sepctra, the onset oxidation/reduction potentials, and further affect the electrolumiscent and photovoltaic properties. Copolymerization can reduce the steric effect and improve the electrolumiscent and photovoltaic properties. The brightness of light‐emitting diodes base on copolymer BE‐co‐MEH‐PPV and BD‐co‐MDMO‐PPV reached 3988 and 3864 cd/m², respectively, much higher than that based on homopolymer BE‐PPV (523 cd/m²) and BD‐PPV (333 cd/m²), also higher than that based on MEH‐PPV (3788 cd/m²). The power conversion efficiency (PCE) of solar cells based on BE‐co‐MEH‐PPV and BD‐co‐MDMO‐PPV reached 1.41, 0.76%, respectively, much higher than that based on BE‐PPV (0.24%) and BD‐PPV (0.14%). Copyright © 2010 John Wiley & Sons, Ltd.     

Versatile preparation of poly(1,4‐phenylenevinylene‐co‐1,4‐phenylene‐1,2‐ethanediyl) by CVD polymerization of p‐(methoxymethyl)benzyl chloride

It was demonstrated that a series of copolymers consisting of 1,4‐phenylenevinylene (PV) and 1,4‐phenylene‐1,2‐ethanediyl (PE) units could be prepared from a single monomer, p‐(methoxymethyl)benzyl chloride, via the chemical vapor deposition polymerization (CVDP) method. The composition of the copolymers could be varied simply by altering the monomer activation temperature. The higher the temperature, the lower the content of the PV unit. The photo (PL)‐ and electroluminescence (EL) properties of the copolymers that revealed a blueshift when compared with PPV strongly depend on the amount of the PE units incorporated. The external quantum efficiencies of the electroluminescence devices having the configuration of ITO/PEDOT‐PSS/copolymer/Al‐Li were higher than that of PPV, which can be ascribed to the improved confinement of excitons. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 742–751, 2005     

Green‐emitting poly[(1,3‐phenylenevinylene)‐alt‐ (1,4‐phenylenevinylene)]s: Effect of the substitution patterns on the optical properties

Green‐emitting substituted poly[(2‐hexyloxy‐5‐methyl‐1,3‐phenylenevinylene)‐alt‐(2,5‐dihexyloxy‐1,4‐phenylenevinylene)]s ( 6 ) were synthesized via the Wittig–Horner reaction. The polymers were yellow resins with molecular weights of 10,600. The ultraviolet–visible (UV–vis) absorption of 6 (λ_max = 332 or 415 nm) was about 30 nm redshifted from that of poly[(2‐hexyloxy‐5‐methyl‐1,3‐phenylenevinylene)‐alt‐(1,4‐phenylenevinylene)] ( 2 ) but was only 5 nm redshifted with respect to that of poly[(1,3‐phenylenevinylene)‐alt‐(2,5‐dihexyloxy‐1,4‐phenylenevinylene)] ( 1 ). A comparison of the optical properties of 1 , 2 , and 6 showed that substitution on m‐ or p‐phenylene could slightly affect their energy gap and luminescence efficiency, thereby fine‐tuning the optical properties of the poly[(m‐phenylene vinylene)‐alt‐(p‐phenylene vinylene)] materials. The vibronic structures were assigned with the aid of low‐temperature UV–vis and fluorescence spectroscopy. Light‐emitting‐diode devices with 6 produced a green electroluminescence output (emission λ_max ～ 533 nm) with an external quantum efficiency of 0.32%. Substitution at m‐phenylene appeared to be effective in perturbing the charge‐injection process in LED devices. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1820–1829, 2004     

Novel saturated red‐emitting poly(p‐phenylenevinylene) copolymers with narrow‐band‐gap units of 2,1,3‐benzothiadiazole synthesized by a palladium‐catalyzed Stille coupling reaction

Novel poly(p‐phenylenevinylene) (PPV) copolymers derived from 1‐methoxy‐4‐octyloxyphenylene (MOP), 2,1,3‐benzothiadiazole (BT), and trans‐1,2‐bis(tributylstannyl)ethylene were first prepared by a palladium‐catalyzed Stille coupling reaction. The feed ratios of MOP to BT were 99.5:0.5, 99:1, 95:5, 85:15, 70:30, and 50:50. An efficient energy transfer from the 2‐methoxy‐5‐octyloxy‐p‐phenylenevinylene segment to the narrow‐band‐gap units was observed. The poly(2‐methoxy‐5‐octyloxy‐p‐phenylenevinylene‐2,1,3‐benzothiadiazolevinylene) copolymers emitted deep red light. The maximum electroluminescence emission of these PPV copolymers occurred at 659–724 nm and was accompanied by gradual redshifting with an increasing BT concentration. The photophysical properties were examined in comparison with those of copolymers based on BT and fluorene or N‐alkylcarbazole doped with the same BT concentration in the copolymer main chain. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2325‐2336, 2005     

Enhancing quantum efficiency of MEH‐PPV through the reduction of chain aggregations by thermal treatments

The quantum efficiencies of photoluminescence (PL) and electro‐luminescence (EL) of poly[2‐methoxy‐5‐(2′‐ethyl‐hexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV) were significantly increased by heat treatments under vacuum with further removing the undissolved portion. The UV–vis absorption was found to decrease with heating time, while PL intensity increased. The maximum PL quantum yield was 6.5 times that of the untreated MEH‐PPV, which was attributed to the reduction of chain aggregations and the interruption of conjugation length. The maximum EL quantum yield of their prepared ITO/PANI/MEH‐PPV/Ca/AL light emitting diodes (PLED) was 46 (at 3 V) times that of the untreated sample. A typical turn‐on voltage of 2.5 V for MEH‐PPV PLED was able to decrease to 1 V after heat treatments, which was believed to result from the decrease of cis linkages in the polymer chains as revealed by the ¹H NMR spectroscopy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1705–1711, 2005     

Electrospinning of polystyrene/poly(2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylene vinylene) blends

Ultrafine polystyrene (PS)/poly(2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylene vinylene) (MEH‐PPV) fibers were successfully prepared by electrospinning of PS/MEH‐PPV solutions in chloroform, 1,2‐dichloroethane, and tetrahydrofuran (THF). Three concentrations of the solutions were prepared: 8.5, 16, and 23.5% (w/v), with the compositional weight ratios between PS and MEH‐PPV being 7.5:1, 15:1, and 22.5:1, respectively. Smooth fibers only observed from 23.5% (w/v) PS/MEH‐PPV solution in chloroform. Improvement in the electrospinnability of 8.5% (w/v) PS/MEH‐PPV solution in chloroform was achieved by addition of an organic salt, pyridinium formate (PF), or by addition of a minor solvent with a high dielectric constant value. The average diameters of the as‐spun PS/MEH‐PPV fibers were between 0.30 and 5.11 μm. Last, photoluminescence of 8.5% (w/v) solutions of PS/MEH‐PPV in a mixed solvent system of chloroform and 1,2‐dichloroethane of various volumetric compositions and the resulting as‐spun fibers was investigated and compared. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1881–1891, 2005     

Dependence of the luminescent properties and chain length of poly[2‐methoxy‐5‐(2′‐ethyl‐hexyloxy)‐1,4‐phenylene vinylene] on the formation of cis‐vinylene bonds during Gilch polymerization

The presence of cis‐vinylene bonds in Gilch‐polymerized poly[2‐methoxy‐5‐(2′‐ethyl‐hexyloxy)‐1,4‐phenylene vinylene] is reported. Through fractionation, species with a weight‐average molecular weight of less than 37,000 exhibited an abnormal blueshift of photoluminescence spectra in toluene solutions, and this was attributed to the presence of cis‐vinylene bonds, as verified by NMR spectroscopy. Surprisingly, the fractionated species (～1 wt %) with a weight‐average molecular weight of 5000 were mostly linked by the cis‐vinylene bonds. The concentration decreased with the molecular weight until a molecular weight of 37,000 was reached; at that point, the polymer chains contained mainly trans‐vinylene bonds. Obviously, the formation of cis‐vinylene bonds strongly inhibited the growth of polymer chains during Gilch polymerization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2520–2526, 2005     

A novel conjugated polymer containing alternating p‐ and n‐type moieties with balanced properties of conducting holes and electrons

A new electroluminescent conjugated polymer consisting of 2,2′‐bipyridylenevinylene (BPyV) and 2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene (MEH‐PV) moieties (BPy‐MEH‐PPV), was synthesized by incorporating an n‐dope type moiety, BPyV, and a p‐dope type moiety, MEH‐PV, into the polymer chain. This facile method provides a new approach to the synthesis of conjugated polymers with balanced ability of conducting electrons and holes. PBy‐MEH‐PPV exhibits tunable optical properties through protonation, and the emissive color can be progressively changed from orange to deep red depending on the degree of protonation.     

Effect of n‐type doping on the hole transport in poly(p‐phenylene vinylene)

N‐type doping of poly(2‐methoxy‐5‐(2′‐ethyl‐hexyloxy)‐p‐phenylene vinylene) (MEH‐PPV) with decamethylcobaltocene (DMC) strongly improves the electron transport due to filling of the electron traps. Unexpectedly, the n‐type doping simultaneously suppresses the hole transport in MEH‐PPV. We demonstrate that this strong reduction of the hole transport originates from unionized DMC molecules that act as hole traps. This hole trapping effect explains why the current of a DMC‐doped MEH‐PPV polymer light‐emitting diode is orders of magnitude lower than that of the undoped device. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Conformation and luminescence characteristics of nanopoly[2‐metoxy‐5‐(2′‐ethyl‐hexyloxy)‐p‐phenylene vinylene] in two‐dimensional arrays

With anodic alumina with an ordered nanopore array used as a template, poly[2‐metoxy‐5‐(2′‐ethyl‐hexyloxy)‐p‐phenylene vinylene] (MEH–PPV) was embedded into the nanopores, and then two‐dimensional arrays of light‐emitting nanopolymers were prepared. By the measurement and analysis of photoluminescence and photoluminescence excitation spectra of the samples, it was demonstrated that the optical properties of the nano‐MEH–PPV arrays were obviously different from those of MEH–PPV films. The conformations of the MEH–PPV chains in the nanopores, films, and solutions and their effects on the optical properties were examined. It was determined experimentally that the conformations of the MEH–PPV chains in the solutions were maintained in the nano‐MEH–PPV arrays. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3037–3041, 2006     

Parameters influencing the molecular weight of 3,6‐carbazole‐based D‐π‐A‐type copolymers

Condensation copolymerization reactions of carbazole 3,6‐diboronate with 4,7‐bis(5‐bromo‐2‐thienyl)‐2,1,3‐benzothiadiazole (DTBT) only produce low‐molecular‐weight donor (D)‐π‐acceptor (A) copolymers. High‐molecular‐weight copolymers for use in optoelectronic devices are necessary for achieving extended π‐conjugation and for controlling the copolymer processibility. To elucidate the cause of the persistently low molecular weight, we synthesized three 3,6‐carbazole‐based D‐A copolymers using copolymerizations of N‐9′‐heptadecanyl‐3,6‐carbazole with DTBT, N‐9′{2‐[2‐(2‐methoxy‐ethoxy)‐ethoxy]‐ethyl}‐3,‐6‐carbazole with DTBT, and N‐9′‐heptadecanyl‐3,6‐carbazole with alkyl‐substituted DTBT. We investigated several parameters for their influence on molecular copolymer weight, including the conformation of the chain during growth, the solubility of the monomers, and the dihedral angles between the donor and acceptor units. Size exclusion chromatography, UV–vis absorption spectroscopy, and computational studies revealed that the low molecular weights of 3,6‐carbazole‐based D‐A copolymers resulted from conjugation breaks and the resulting high coplanarity, which led to strong interactions between polymer chains. These interactions limited formation of high‐molecular‐weight‐copolymers during copolymerization. The strong intermolecular interactions of the 3,6‐carbazole moiety were exploited by incorporating 3,6‐carbazole units into poly[9′,9′‐dioctyl‐2,7‐flourene‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)] prepared from 9′,9′‐dioctyl‐2,7‐flourene and DTBT. Interestingly, the number average molecular weight increased gradually with increasing 2,7‐fluorene monomer content but the number of conjugation breaks was a range of 6–7. The hole mobilities of the copolymers were studied for comparison purposes. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of new polyfluorene copolymers with a comonomer containing triphenylamine units and their applications in white‐light‐emitting diodes

Novel conjugated polyfluorene copolymers, poly[9,9‐dihexylfluorene‐2,7‐diyl‐co‐(2,5‐bis(4′‐diphenylaminostyryl)‐phenylene‐1,4‐diyl)]s (PGs), have been synthesized by nickel(0)‐mediated polymerization from 2,7‐dibromo‐9,9‐dihexylfluorene and 1,4′‐dibromo‐2,5‐bis(4‐diphenylaminostyryl)benzene with various molar ratios of the monomers. Because of the incorporation of triphenylamine (TPA) moieties, PGs exhibit much higher HOMO levels than the corresponding polyfluorene homopolymers and are able to facilitate hole injection into the polymer layer from the anode electrode in light‐emitting diodes. Conventional polymeric light‐emitting devices with the configuration ITO/PEDOT:PSS/polymer/Ca/Al have been fabricated. A light‐emitting device produced with one of the PG copolymers (PG10) as the emitting layer exhibited a voltage‐independent and stable bluish‐green emission with color coordinates of (0.22, 0.42) at 5 V. The maximum brightness and current efficiency of the PG10 device were 3370 cd/m² (at 9.6 V) and 0.6 cd/A, respectively. To realize a white polymeric light‐emitting diode, PG10 as the host material was blended with 1.0 wt % of a red‐light‐emitting polymer, poly[9,9‐dioctylfluorene‐2,7‐diyl‐alt‐2,5‐bis(2‐thienyl‐2‐cyanovinyl)‐1‐(2′‐ethylhexyloxy)‐4‐methoxybenzene‐5′,5′‐diyl] (PFR4‐S), and poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV). The device based on PG10:PFR4‐S showed an almost perfect pure white electroluminescence emission, with Commission Internationale de l'Eclairage (CIE) coordinates of (0.33, 0.36) at 8 V; for the PG10:MEH‐PPV device, the CIE coordinates at this voltage were (0.30, 0.40) with a maximum brightness of 1930 cd/m². Moreover, the white‐light emission from the PG10:PFR4‐S device was stable even at different driving voltages and had CIE coordinates of (0.34, 0.36) at 6 V and (0.31, 0.35) at 10 V. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1199–1209, 2007     

Synthesis and optoelectronic properties of luminescent poly(p‐phenylenevinylene) derivatives containing electron‐transporting 1,3,4‐oxadiazole groups

Three random copolymers ( P1–P3 ) comprising phenylenevinylene and electron‐transporting aromatic 1,3,4‐oxadiazole segments (11, 18, 28 mol %, respectively) were prepared by Gilch polymerization to investigate the influence of oxadiazole content on their photophysical, electrochemical, and electroluminescent properties. For comparative study, homopolymer poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐p‐phenylenevinylene] ( P0 ) was also prepared by the same process. The polymers ( P0–P3 ) are soluble in common organic solvents and thermally stable up to 410 °C under a nitrogen atmosphere. Their optical properties were investigated by absorption and photoluminescence spectroscopy. The optical results reveal that the aromatic 1,3,4‐oxadiazole chromophores in P1–P3 suppress the intermolecular interactions. The HOMO and LUMO levels of these polymers were estimated from their cyclic voltammograms. The HOMO levels of P0–P3 are very similar (?5.02 to ?5.03 eV), whereas their LUMO levels decrease readily with increasing oxadiazole content (?2.7, ?3.08, ?3.11, and ?3.19 eV, respectively). Therefore, the electron affinity of the poly(p‐phenylenevinylene) chain can be gradually enhanced by incorporating 1,3,4‐oxadiazole segments. Among the polymers, P1 (11 mol % 1,3,4‐oxadiazole) shows the best EL performance (maximal luminance: 3490 cd/m², maximal current efficiency: 0.1 cd/A). Further increase in oxadiazole content results in micro‐phase separation that leads to performance deterioration. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4377–4388, 2007     

Synthesis and opto‐electrical properties of dendron‐containing poly(2,3‐diphenyl‐1,4‐phenylenevinylene) derivatives

A new series of poly(2,3‐diphenyl‐1,4‐phenylenevinylene) derivatives containing dendritic side groups were synthesized. Different generations of dendrons were integrated on the pendant phenyl ring to investigate their effect on optical and electrical properties of final polymers. Homopolymers can not be obtained via the Gilch polymerization because of sterically bulky dendrons. By controlling the feed ratio of different monomers during polymerization, dendron‐containing copolymers with high molecular weights were obtained. The UV–vis absorption and photoluminescent spectra of the thin films are pretty close; however, quantum efficiency is significantly enhanced with increasing the generation of dendrons. The electrochemical analysis reveals that hole‐injection is also improved by increasing dendritic generation. Double‐layer light‐emitting devices with the configuration of ITO/PEDOT:PSS/polymer/Ca/Al were fabricated. High generation dendrons bring benefit of improved device performance. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3440–3450, 2007     

High red,green, and blue color purity electroluminescence from MEH‐PPV and polyalkyfluorenes‐based bright white polymer light emitting displays

A series of white polymer light emitting displays (PLEDs) based on a polymer blend of polyalkylfluorenes and poly(2‐methoxy‐5,2′‐ethyl‐hexyloxy‐1,4‐phenylene vinylene) (MEH‐PPV) was developed. MEH‐PPV or red light emitting alkyfluorene copolymer (PFR) was blended with blue light emitting alkyfluorene copolymer (PFB), and MEH‐PPV was blended with both green light emitting alkyfluorene copolymer (PFG) and PFB to generate white light emission PLEDs. Low turn on voltage (2.7 V), high brightness (12,149 nits), high efficiency (4.0 cd/A, 4.0 lm/W), and good color purity (Commission Internationale de L'Eclairage (CIE_x,y) co‐ordinates (0.32, 0.34)) were obtained for the white PLEDs based on the PFB and MEH‐PPV polymer blend. Exciplex formation in the interface between PFR and PFB induced a new green emission peak for these two components based white PLEDs. As a result, strong white emission (4078 nits) was obtained by mixing the red, green, and blue (RGB) three primary colors. High color purity of blue (CIE, x = 0.14, y = 0.08), green (CIE, x = 0.32, y = 0.64) and red (CIE, x = 0.67, y = 0.33) emissions was achieved for white PLEDs combining with dielectric interference color‐filters. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 330–341, 2007     

Luminescent copoly(aryl ether)s consisting of alternate oxadiazole and 1,4‐distyrylbenzene derivatives: Synthesis and characterization

In an effort to decrease the electron‐injection barrier from the anode electrode, four copoly(aryl ether)s ( P1 – P4 ), consisting of alternating isolated electron‐transporting [2,5‐diphenyl‐1,3,4‐oxadiazole for P1 and P3 and 5,5′‐diphenyl‐2,2′‐p‐(2,5‐bishexyloxyphenylene)‐bis‐1,3,4‐oxadiazole for P2 and P4 ] and emitting chromophores (1,4‐distyryl‐2,5‐dihexyloxybenzene for P1 and P2 and 1,4‐distyryl‐2,5‐dihexylbenzene for P3 and P4 ), have been synthesized by the nucleophilic displacement reaction between bisfluoride and bisphenol monomers. They are basically amorphous materials with 5% weight‐loss temperature above 400 °C. The photoluminescence spectra and quantum yields of these copolymers are dependent on the compositions of the two isolated fluorophores. The highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels of these copolymers have been estimated from their cyclic voltammograms. All the observations directly prove that the oxidation starts at the hole‐transporting segments. The electron affinity can be enhanced by the introduction of isolated electron‐transporting segments that lead to a charge‐injection balance. Single‐layer light‐emitting diodes (Al/ P1 – P4 /ITO glass) have been fabricated. P1 and P2 reveal blue electroluminescence, and P3 and P4 reveal purple‐blue electroluminescence. Moreover, the incorporation of bisoxadiazole units increases the electron affinity and reduces the turn‐on electric field better than one oxadiazole unit. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2765–2777, 2003     

Segmented poly[2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐phenylene vinylene] via xanthate and dithiocarbamate precursors: A comparative study of thermal eliminations

Segmented poly[2‐methoxy‐5‐(2‐ethylhexloxy)‐1,4‐phenylene vinylene] (MEH‐PPV)‐x's, which contain conjugated segments of varying lengths that are interspersed by nonconjugated units along the polymer backbone, were synthesized by selective thermal elimination of precursors containing controlled amounts (x) of a thermally labile group, namely, xanthate or dithiocarbamate (DTC). These precursors were in turn synthesized by competitive nucleophilic substitution of the Wessling polyelectrolyte with varying molar fractions of the respective nucleophiles—potassium ethyl xanthate or sodium diethyl dithiocarbamate. Methanol, used as the reaction medium, also served to introduce the second thermally less labile nucleophilic substituent. This approach for the preparation of segmented MEH‐PPV‐x is superior to the previous approach that used acetate as the thermally labile group, because it offers greater control over the composition despite a simpler synthetic procedure. Detailed studies of the thermal‐elimination kinetics of the three precursors, namely, acetate, xanthate, and DTC, both in solution and in thin films, were carried by in situ monitoring of their ultraviolet–visible spectra. These studies revealed that the rates of elimination followed the order, DTC > xanthate > acetate. The activation energies for the elimination were, however, not widely different (ca. 30 kcal/mol), suggesting that the rates primarily reflected differences in the pre‐exponential factor. After elimination, the segmented MEH‐PPV‐x samples exhibited the expected redshift in their absorption and fluorescence spectra with an increasing molar fraction (x) of eliminated segments, which was accompanied by a drastic reduction in the fluorescence quantum yields. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3929–3940, 2003