Solid polymer electrolytes. VI. Microstructure of organic–inorganic hybrid networks composed of 3‐glycidoxypropyltrimethoxysilane and LiClO4 and affected by different synthetic routes

Hybrid organic–inorganic materials derived from 3‐glycidoxypropyltrimethoxylsilane were prepared via two different synthetic routes: (1) the HCl‐catalyzed sol–gel approach of silane followed by the lithium perchlorate (LiClO₄)/HCl‐catalyzed opening of epoxide and (2) the simultaneous gelation of tin/LiClO₄‐catalyzed silane/epoxide groups. LiClO₄ catalyzed the epoxide polymerization, and its effects on the structures of these hybrid materials were studied by NMR. The structure of the inorganic side was probed by solid‐state ²⁹Si NMR spectroscopy, and the characterizations of the organic side and the chemical processes involved in the different synthetic routes were performed with solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR. The different synthetic routes significantly affected the polymerization behaviors of the organic and inorganic sides in the presence of LiClO₄. A larger amount of LiClO₄ promoted the opening of epoxide and led to the formation of longer poly(ethylene oxide) chains via the HCl‐catalyzed sol–gel approach, whereas in the case of the tin‐catalyzed approach, the faster polymerization of the inorganic side hindered the growth of the organic network. The addition of LiClO₄ was proven to be without crystalline salt present in the hybrid networks by wide‐angle X‐ray powder diffraction. Also, the interactions between the ions and hybrid host, examined with Fourier transform infrared and ⁷Li proton‐decoupled magic‐angle‐spinning NMR, further demonstrated that extensive ion aggregation existed in these hybrid materials. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 151–161, 2004     

Preparation of poly(methyl acrylate‐co‐itaconic anhydride)/SiO2 hybrid materials via the sol–gel process—The effect of the coupling agent,inorganic content,and nature of the catalyst

Transparent poly(methyl acrylate‐co‐itaconic anhydride)/SiO₂ hybrid materials were prepared from methyl acrylate‐itaconic anhydride copolymer and tetraethoxysilane (TEOS) with the coupling agent (3‐aminopropyl)triethoxysilane (APTES) via a sol–gel process. The covalent bonds between the organic and inorganic phases were introduced by the in situ aminolysis of the itaconic anhydride units with APTES forming a copolymer bearing a triethoxysilyl group. These groups subsequently were hydrolyzed with TEOS and allowed to form a network. These reactions were monitored by Fourier transform infrared analysis. The amount of APTES had a dramatic influence on the gel time and sol fraction. The effect of APTES, the inorganic content, and the nature of the catalyst on the thermal properties and morphology of the hybrid materials were studied by differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy, and atomic force microscopy. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 321–328, 2000     

Trialkoxysilane‐capped acrylic resin/titania organic–inorganic hybrid optical films prepared by the sol–gel process

Homogeneous organic–inorganic hybrid materials with excellent thermal and optical performance were successfully prepared via the mixing of (3‐methacryloxypropyl)trimethoxysilane‐capped acrylic resin with titania synthesized by sol–gel approaches. The effects of the titania content, amount of water, and pH in the sol–gel and the ratio of the solvents (butyl acetate and ethanol) on the structures and properties of the hybrid materials were studied. More titania, more water, and base catalysis in the sol–gel process and a higher ratio of butyl acetate to ethanol for the hybrids led to a larger size and a more compact structure of the titania phase. Increasing the titania content dramatically improved the glass‐transition temperature, UV‐shielding properties, and refractive index for the hybrid materials, and it did not reduce their optical transparency. In general, better thermal stability and optical properties were achieved for the hybrid materials prepared with less water, lower pH values (e.g., acidic or neutral conditions), and a lower ratio of butyl acetate to ethanol. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 637–649, 2005     

Synthesis and properties of bismaleimide‐modified novolak resin/silsesquioxane nanocomposites

Bismaleimide‐modified novolak resin/silsesquioxane (BMI‐PN/SiO_3/2) nanocomposites were prepared by the sol–gel process. The reactions in the sol–gel synthesis were characterized by Fourier transform infrared spectroscopy. It was found by field emission scanning electron microscopy and atomic force microscopy studies that the particle size of the dispersed phase was about 100 nm, and there existed particle aggregates. The proportion of bismaleimide in the BMI‐PN/SiO_3/2 nanocomposites showed an important effect on the thermal properties of the composites, as demonstrated by thermogravimetric analysis and dynamical mechanical analysis. Major improvements in the glass‐transition temperature and the heat resistance of the material were achieved by the introduction of the nanosized SiO_3/2 inorganic phase, and the modulus at high temperatures was improved too. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2599–2606, 2003     

Preparation of methoxy poly(ethylene glycol)/polyester diblock copolymers and examination of the gel‐to‐sol transition

Diblock copolymers consisting of methoxy poly(ethylene glycol) (MPEG) and poly(?‐caprolactone) (PCL), poly(δ‐valerolactone) (PVL), poly(L ‐lactic acid) (PLLA), or poly(lactic‐co‐glycolic acid) (PLGA) as biodegradable polyesters were prepared to examine the phase transition of diblock copolymer solutions. MPEG–PCL and MPEG–PVL diblock copolymers and MPEG–PLLA and MPEG–PLGA diblock copolymers were synthesized by the ring‐opening polymerization of ?‐caprolactone or δ‐valerolactone in the presence of HCl · Et₂O as a monomer activator at room temperature and by the ring‐opening polymerization of L ‐lactide or a mixture of L ‐lactide and glycolide in the presence of stannous octoate at 130 °C, respectively. The synthesized diblock copolymers were characterized with ¹H NMR, IR, and gel permeation chromatography. The phase transitions for diblock copolymer aqueous solutions of various concentrations were explored according to the temperature variation. The diblock copolymer solutions exhibited the phase transition from gel to sol with increasing temperature. As the polyester block length of the diblock copolymers increased, the gel‐to‐sol transition moved to a lower concentration region. The gel‐to‐sol transition showed a dependence on the length of the polyester block segment. According to X‐ray diffraction and differential scanning calorimetry thermal studies, the gel‐to‐sol transition of the diblock copolymer solutions depended on their degrees of crystallinity because water could easily diffuse into amorphous polymers in comparison with polymers with a crystalline structure. The crystallinity markedly depended on both the distinct character and composition of the block segment. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5784–5793, 2004     

Synthesis of transition‐metal‐ion‐selective poly(N‐isopropylacrylamide) hydrogels by the incorporation of an Aza crown ether

A functionalized cyclam was synthesized by the attachment of a polymerizable acryloyl group to one of the four nitrogens on the cyclam molecule. The polymerization of the functionalized cyclam was performed with N‐isopropylacrylamide and N,N′‐methylene bisacrylamide, and the gels obtained were studied in the presence of different transition‐metal‐ion solutions. There was a drastic difference in the phase‐transition temperature (T_c) of the poly(N‐isopropylacrylamide) (PNIPAAm)/cyclam gel in comparison with the pure PNIPAAm gel. For the described system, a T_c shift of 15 °C was obtained. The presence of functionalized cyclam increased the hydrophilicity and T_c of the aforementioned polymer gels in deionized water (at pH 6) because of the presence of protonated amino moieties. The PNIPAAm/cyclam gels showed a dependence of the swelling behavior on pH. T_c of the pure PNIPAAm gel was weakly influenced by the presence of any transition‐metal ions, such as Cu²⁺, Ni²⁺, Zn²⁺, and Mn²⁺. The addition of Cu²⁺ or Ni²⁺ to the PNIPAAm/cyclam gel reduced T_c of the polymer gel, and a shift of approximately 12 °C was observed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1594–1602, 2003     

Synthesis and polymerization of 5‐(methacrylamido)tetrazole,a water‐soluble acidic monomer

The reaction of methacryloyl chloride with 5‐aminotetrazole gave the polymerizable methacrylamide derivative 5‐(methacrylamido)tetrazole ( 4 ) in one step. The monomer had an acidic tetrazole group with a pK_a value of 4.50 ± 0.01 in water methanol (2:1). Radical polymerization proceeded smoothly in dimethyl formamide or, after the conversion of monomer 4 into sodium salt 4‐Na , even in water. A superabsorbent polymer gel was obtained by the copolymerization of 4‐Na and 0.08 mol % N,N′‐methylenebisacrylamide. Its water absorbency was about 200 g of water/g of polymer, although the extractable sol content of the gel turned out to be high. The consumption of 4‐Na and acrylamide (as a model compound for the crosslinker) during a radical polymerization at 57 °C in D₂O was followed by ¹H NMR spectroscopy. Fitting the changes in the monomer concentration to the integrated form of the copolymerization equation gave the reactivity ratios r _4‐Na = 1.10 ± 0.05 and r_acrylamide = 0.45 ± 0.02, which did not differ much from those of an ideal copolymerization. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4333–4343, 2002     

Effect of photoinitiator on photopolymerization of inorganic–organic hybrid polymers (ORMOCER®)

Inorganic–organic hybrid polymers have been developed and tested for evaluation in optical and electrical applications. Although hybrid inorganic–organic polymers can be synthesized by sol–gel chemistry at first, the physical properties of hybrid inorganic–organic polymers are changed during thin film-making processes, that is, photocuring and thermal curing. To investigate the effect of photoinitiator on the material properties during processing, a model system containing methacrylic groups as organically polymerizable units was selected. The conversion of CC double bond of methacrylic groups depending on some kinds of photoinitiator quantities was characterized by Fourier transform infrared spectroscopy. It was confirmed to correlate the degree of CC double bond conversion with the refractive indices. Thermodynamically, the enthalpy of the photopolymerization of hybrid polymer was investigated by UV–DSC. UV–DSC spectra showed the exothermic nature of photopolymerization of ORMOCER® to be in dependence of photoinitiator quantities. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1979–1986, 2004     

Combination of radical and cationic photoprocesses for the single‐step synthesis of organic‐inorganic hybrid films

Nanocomposite materials prepared from radically photocurable hybrid sol–gel precursors have been widely developed within the last decade, especially to devise novel optical devices and coatings. For their synthesis, a preferential route has involved in the successive sol–gel process of acrylate trialkoxysilane precursors followed by radical photopolymerization. In contrast, this work presents an original one‐step synthesis based on the association of two different photoinitiators (PIs) in the same formulation: the photolysis of a hydroxyphenylketone (radical PI) affords polyacrylate chains while that of a diaryl iodonium salt (cationic PI) generates powerful superacids catalyzing the sol–gel reactions of the alkoxy functions. The behavior of methacrylate and acrylate trimethoxysilane precursors was compared to highlight the effect of the organic moiety functionality on the reaction kinetics (Fourier transform infrared spectroscopy) and the film microstructure (¹³C and ²⁹Si solid‐state nuclear magnetic resonance). Interestingly, evidence of local organization in these hybrid films was also given by X‐ray analysis. In a last part, their thermomechanical properties were discussed thoroughly using a range of techniques: DSC, scratch‐resistance test, nanoindentation. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4150–4158, 2010     

Preparation,characterization, and properties of novolac‐type phenolic/SiO2 hybrid organic–inorganic nanocomposite materials by sol–gel method

This article describes the preparation of novolac‐type phenolic resin/silica hybrid organic–inorganic nanocomposite, with a sol–gel process. The coupling agent was used to improve the interface between the organic and inorganic phases. The effect of the structure of the nanocomposite on its physical and chemical properties is discussed. The coupling agent reacts with the resin to form covalent bonds. The structure of the modified hybrid nanocomposites was identified with a Fourier transform infrared spectroscope. The silica network was characterized by nuclear magnetic resonance imaging (²⁹Si NMR). Results revealed that Q₄ (tetrasubstituted) and T₃ (trisubstituted) are the dominant microstructures. The size of the silica in the phenolic resin was characterized with a scanning electron microscope. The size of the particles of inorganic silica in the modified system was less than 100 nm. The nanocomposite exhibited good transparency. Moreover, the thermal and mechanical properties exhibited significant improvement. The modified hybrid composite exhibited favorable thermal properties. The temperature at which a weight loss of 5% occurred increased from 281 to 350 °C. The flexural strength increased by 6–30%. The limiting oxygen index of the nanocomposite reached 37, and the Underwriters Laboratory test was 94V‐0. Consequently, these materials possess excellent flame‐retardant properties. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 905–913, 2003     

Preparation of photocrosslinked sol‐gel composites based on urethane‐acrylic matrix,silsesquioxane sequences,TiO2, and Ag/Au Nanoparticles for use in photocatalytic applications

An acid urethane oligodimethacrylate based on poly(ethylene glycol) was synthesized and used in the preparation of hybrid composites containing silsesquioxane sequences and titania domains formed through sol‐gel reactions along with silver/gold nanoparticles (Ag/Au NPs) in situ photogenerated during the UV‐curing process. The photopolymerization kinetics studied by Fourier transform infrared spectroscopy and photoDSC showed that the photoreactivity of the investigated formulations depends on the amount of titanium butoxide (5–20 wt %) added in the system subjected to UV irradiation. The introduction of 1 wt % AgNO₃/AuBr₃ in formulations slightly improved the degree of conversion but diminished the polymerization rates. The formation of hybrid materials comprising predominantly amorphous TiO₂/SiO₂ NPs, with or without Ag/Au NPs, was confirmed through specific analyses. The evaluation of photocatalytic activity demonstrated that the synthesized hybrid films are suitable for the complete removal of organic pollutants (phenolic compounds) from water under UV irradiation (200–350 min) at low intensity (found in the solar radiation). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1189–1204     

Synthesis of well‐defined polymers end‐functionalized with crosslinkable aziridine groups by living anionic polymerization

Well‐defined end‐functionalized polystyrene, poly(α‐methylstyrene), and polyisoprene with polymerizable aziridine groups were synthesized by the termination reactions of the anionic living polymers of styrene, α‐methylstyrene, and isoprene with 1‐[2‐(4‐chlorobutoxy)ethyl]aziridine in tetrahydrofuran at ?78 °C. The resulting polymers possessed the predicted molecular weights and narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight < 1.1) as well as aziridine terminal moieties. The cationic ring‐opening polymerization of the ω‐monofunctionalized polystyrene having an aziridinyl group with Et₃OBF₄ gave the polymacromonomer, whereas the α,ω‐difunctional polystyrene underwent crosslinking reactions to afford an insoluble gel. Crosslinking products were similarly obtained by the reaction of the α,ω‐diaziridinyl polystyrene with poly(acrylic acid)‐co‐poly(butyl acrylate). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4126–4135, 2005     

Polymerization of 1,3‐dienes with functional groups. II. Free‐radical polymerization of N‐(2‐methylene‐3‐butenoyl)piperidine

The free‐radical homopolymerization and copolymerization behavior of N‐(2‐methylene‐3‐butenoyl)piperidine was investigated. When the monomer was heated in bulk at 60 °C for 25 h without an initiator, about 30% of the monomer was consumed by the thermal polymerization and the Diels–Alder reaction. No such side reaction was observed when the polymerization was carried out in a benzene solution with 1 mol % 2,2′‐azobisisobutylonitrile (AIBN) as an initiator. The polymerization rate equation was found to be R_p ∝ [AIBN]^0.507[M]^1.04, and the overall activation energy of polymerization was calculated to be 89.5 kJ/mol. The microstructure of the resulting polymer was exclusively a 1,4‐structure that included both 1,4‐E and 1,4‐Z configurations. The copolymerizations of this monomer with styrene and/or chloroprene as comonomers were carried out in benzene solutions at 60 °C with AIBN as an initiator. In the copolymerization with styrene, the monomer reactivity ratios were r₁ = 6.10 and r₂ = 0.03, and the Q and e values were calculated to be 10.8 and 0.45, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1545–1552, 2003     

Tailored thioxanthone‐based photoinitiators for two‐photon‐controllable polymerization and nanolithographic printing

Printing of high‐resolution three‐dimensional nanostructures utilizing two‐photon polymerization has gained significant attention recently. In particular, isopropyl thioxanthone (ITX) has been implemented as a photoinitiator due to its capability of initiating and depleting polymerization on demand, but new photoinitiating materials are still needed in order to reduce the power requirements for the high‐throughput creation of 3D structures. To address this point, a suite of new thioxanthone‐based photoinitiators were synthesized and characterized. Then two‐photon polymerization was performed using the most promising photoinitiating molecule. Importantly, one of the initiators, 2,7‐bis[(4‐(dimethylamino)phenyl ethynyl)‐9H‐thioxanthen‐9‐one] (BDAPT), showed a fivefold improvement in the writing threshold over the commonly used ITX molecule. To elucidate the fundamental mechanism, the excitation and inhibition behavior of the BDAPT molecule were evaluated using density functional theory (DFT) calculations, low‐temperature phosphorescence spectroscopy, ultra‐fast transient absorption spectroscopy, and the two‐photon Z‐scan spectroscopic technique. The improved polymerization threshold of this new photoinitiator presents a clear pathway for the modification of photoinitiators in 3D nanoprinting. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1462–1475     

Effects of the structures of polymerizable monomers on the electro‐optical properties of UV cured polymer dispersed liquid crystal films

Polymer dispersed liquid crystal (PDLC) films were prepared by photopolymerization of liquid crystal (LC)/polymerizable monomers/photoinitiator composites. The effects of the structures of the polymerizable monomers on the electro‐optical properties of PDLC films were investigated. It was found that the length of the molecular chain and the rigidity and flexibility of molecules influenced the structure of the polymer network in the PDLC films somewhat, and then affected the electro‐optical properties of the composites accordingly. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1369–1375, 2008     

Ring‐opening metathesis polymerization as a route to controlled copolymers of ethylene and polar monomers: Synthesis of ethylene–vinyl chloride‐like copolymers

A series of ethylene–vinyl chloride‐like copolymers were prepared by ring‐opening metathesis polymerization (ROMP). The route to these materials included the bulk polymerization of 5‐chlorocyclooctene and 5,6‐dichlorocyclooctene with the first‐generation Grubbs' catalyst, followed by diimide hydrogenation of the resulting unsaturated polymers. In addition, the amount of chlorine in these materials was varied by the copolymerization of 5‐chlorocyclooctene with cyclooctene. These materials were fully characterized by NMR (¹H and ¹³C), gel permeation chromatography, and Fourier transform infrared spectroscopy. Finally, hydroboration was carried out on the ROMP product of 5‐chlorocyclooctene to yield a polymer, which was effectively a vinyl alcohol–vinyl chloride–ethylene terpolymer. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2107–2116, 2003     

Acrylic polymer/silica hybrids prepared by emulsifier‐free emulsion polymerization and the sol–gel process

Acrylic polymer/silica hybrids were prepared by emulsifier‐free emulsion polymerization and the sol–gel process. Acrylic polymer emulsions containing triethoxysilyl groups were synthesized by emulsifier‐free batch emulsion polymerization. The acrylic polymer/silica hybrid films prepared from the acrylic polymer emulsions and tetraethoxysilane (TEOS) were transparent and solvent‐resistant. Atomic force microscopy studies of the hybrid film surface suggested that the hybrid films did not contain large (e.g., micrometer‐size) silica particles, which could be formed because of the organic–inorganic phase separation. The Si? O? Si bond formed by the cocondensation of TEOS and the triethoxysilyl groups on the acrylic polymer increased the miscibility between the acrylic polymer component and the silica component in the hybrid films, in which the nanometer‐size silica domains (particles) were dispersed homogeneously in the acrylic polymer component. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 273–280, 2006     

Poly(ϵ‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ϵ‐caprolactone) triblock copolymers: Synthesis and self‐assembly in aqueous solutions

Nontoxic and biodegradable poly(?‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(?‐caprolactone) triblock copolymers were synthesized by the solution polymerization of ?‐caprolactone in the presence of poly(ethylene glycol). The chemical structure of the resulting triblock copolymer was characterized with ¹H NMR and gel permeation chromatography. In aqueous solutions of the triblock copolymers, the micellization and sol–gel‐transition behaviors were investigated. The experimental results showed that the unimer‐to‐micelle transition did occur. In a sol–gel‐transition phase diagram obtained by the vial‐tilting method, the boundary curve shifted to the left, and the gel regions expanded with the increasing molecular weight of the poly(?‐caprolactone) block. In addition, the hydrodynamic diameters of the micelles were almost independent of the investigated temperature (25–55 °C). The atomic force microscopy results showed that spherical micelles formed at the copolymer concentration of 2.5 × 10^?4 g/mL, whereas necklace‐like and worm‐like shapes were adopted when the concentration was 0.25 g/mL, which was high enough to form a gel. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 605–613, 2007     

Synthesis of a novel hybrid liquid‐crystalline rod–coil diblock copolymer

A series of novel rod–coil diblock copolymers on the basis of mesogen‐jacketed liquid‐crystalline polymer were successfully prepared by atom transfer radical polymerization from the flexible polydimethylsiloxane (PDMS) macroinitiator. The hybrid diblock copolymers, poly{2,5‐bis[(4‐methoxyphenyl)oxycarbonyl]styrene}‐block‐polydimethylsiloxane, had number‐average molecular weights (M_n's) ranging from 9500 to 30,900 and relatively narrow polydispersities (≤1.34). The polymerization proceeded with first‐order kinetics. Data from differential scanning calorimetry validated the microphase separation of the diblock copolymers. All block copolymers exhibited thermotropic liquid‐crystalline behavior except for the one with M_n being 9500. Four liquid‐crystalline diblock copolymers with PDMS weight fractions of more than 18% had two distinctive glass‐transition temperatures. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1799–1806, 2003