Preparation and properties of poly(N‐isopropylacrylamide)/poly(N‐isopropylacrylamide) interpenetrating polymer networks for drug delivery

A novel poly(N‐isopropylacrylamide) (PNIPA)/PNIPA interpenetrating polymer network (IPN) was synthesized and characterized. In comparison with conventional PNIPA hydrogels, the shrinking rate of the IPN hydrogel increased when gels, swollen at 20 °C, were immersed in 50 °C water. The phase‐transition temperature of the IPN gel remained unchangeable because of the same chemical constituent in the PNIPA gel. The reswelling kinetics were slower than those of the PNIPA hydrogel because of the higher crosslinking density of the IPN hydrogel. The IPN hydrogel had better mechanical strength because of its higher crosslinking density and polymer volume fraction. The release behavior of 5‐fluorouracil (5‐Fu) from the IPN hydrogel showed that, at a lower temperature, the release of 5‐Fu was controlled by the diffusion of water molecules in the gel network. At a higher temperature, 5‐Fu inside the gel could not diffuse into the medium after a burst release caused by the release of the drug on the surface of the gel. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1249–1254, 2004     

Synthesis of transition‐metal‐ion‐selective poly(N‐isopropylacrylamide) hydrogels by the incorporation of an Aza crown ether

A functionalized cyclam was synthesized by the attachment of a polymerizable acryloyl group to one of the four nitrogens on the cyclam molecule. The polymerization of the functionalized cyclam was performed with N‐isopropylacrylamide and N,N′‐methylene bisacrylamide, and the gels obtained were studied in the presence of different transition‐metal‐ion solutions. There was a drastic difference in the phase‐transition temperature (T_c) of the poly(N‐isopropylacrylamide) (PNIPAAm)/cyclam gel in comparison with the pure PNIPAAm gel. For the described system, a T_c shift of 15 °C was obtained. The presence of functionalized cyclam increased the hydrophilicity and T_c of the aforementioned polymer gels in deionized water (at pH 6) because of the presence of protonated amino moieties. The PNIPAAm/cyclam gels showed a dependence of the swelling behavior on pH. T_c of the pure PNIPAAm gel was weakly influenced by the presence of any transition‐metal ions, such as Cu²⁺, Ni²⁺, Zn²⁺, and Mn²⁺. The addition of Cu²⁺ or Ni²⁺ to the PNIPAAm/cyclam gel reduced T_c of the polymer gel, and a shift of approximately 12 °C was observed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1594–1602, 2003     

Investigation of swelling,drug release and diffusion behaviors of poly(N‐isopropylacrylamide)/poly (N‐vinylpyrrolidone) full‐IPN hydrogels

The synthesis of sequential full interpenetrating polymer networks (IPNs) based on poly (N‐isopropylacrylamide) (PNIPAAm) and negatively charged poly(N‐vinyl‐2‐pyrrolidone) (PNVP) was described and their swelling, drug release, and diffusion studies were investigated. PNIPAAm was used as a host network. According to swelling experiments, IPNs gave relatively lower swelling ratios compared to PNIPAAm hydrogel due to the higher cross‐linking density. Lidocaine (LD) was used as a model drug for the investigation of drug release behavior of IPNs. LD uptake of the IPNs were found to increase from 24 to 166 (mg LD / g dry gel) with increasing amount of PNIPAAm and AMPS contents in the IPN structure. It was observed that the specific interaction between drug and AMPS co‐monomer influenced the drug release profile. In the diffusion transport mechanism study in water, the results indicated that the swelling exponents n for all IPNs are in the range from 0.50 to 0.72. This implies that the swelling transport mechanism was transferred from Fickian to non‐Fickian transport, with increasing AMPS content and NIPAAm character in the IPN structure. In addition, diffusion of LD within the IPNs showed similar trend. The incorporation of AMPS leads to an increase in electrostatic interaction between charge sites on carboxylate ions and cationic LD molecules. Therefore, the highest diffusion coefficient (D) of drug was found for IPN2 sample. Copyright © 2007 John Wiley & Sons, Ltd.     

Novel poly(N‐isopropylacrylamide)/clay/poly(acrylamide) IPN hydrogels with the response rate and drug release controlled by clay content

Novel interpenetrating network (IPN) hydrogels (PNIPAAm/clay/PAAm hydrogels) based on poly(N‐isopropylacrylamide) (PNIPAAm) crosslinked by inorganic clay and poly(acrylamide) (PAAm) crosslinked by organic crosslinker were prepared in situ by ultraviolet (UV) irradiation polymerization. The effects of clay content on temperature dependence of equilibrium swelling ratio, deswelling behavior, thermal behavior, and the interior morphology of resultant IPN hydrogels were investigated with the help of Fourier transform infrared spectroscopy, differential scanning calorimeter (DSC), scanning electron microscope (SEM). Study on temperature dependence of equilibrium swelling ratio showed that all IPN hydrogels exhibited temperature‐sensitivity. DSC further revealed that the temperature‐sensitivity was weakened with increasing amount of clay. Study on deswelling behavior revealed that IPN hydrogels had much faster response rate when comparing with PNIPAAm/clay hydrogels, and the response rate of IPN hydrogels could be controlled by clay content. SEM revealed that there existed difference in the interior morphology of IPN hydrogels between 20 [below lower critical solution temperature (LCST)] and 50 °C (above LCST), and this difference would become obvious with a decrease in clay content. For the standpoint of applications, oscillating swelling/deswelling behavior was investigated to determine whether properties of IPN hydrogels would be stable for potential applications. Bovine serum albumin (BSA) was used as model drug for in vitro experiment, the release data suggested that the controlled drug release could be achieved by modulating clay content. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 96–106, 2009     

Rapid and controlled deswelling of porous poly(N‐isopropylacrylamide) hydrogels prepared by the templating of interpenetrated nanoporous silica particles

Free radical polymerization of N‐isopropylacrylamide (NIPAAm) and crosslinker solutions, which were fulfilled in silica particles with an interpenetrated and nanometer‐sized porous structure (a diameter of 3 mm and mean pore sizes of 15, 30, and 50 nm), fabricated hybrids of organic hydrogels and inorganic silica. Differential scanning calorimetric analyses of the hybrids revealed that silica components affected the thermoresponsive properties of polyNIPAAm hydrogels. Porous polyNIPAAm hydrogels were prepared by the subsequent acid treatment of the hybrids to remove silica. Transmission Fourier transformed infrared spectra indicated the selective extraction of silica. Scanning electron microscopic observation of the hydrogels confirmed the porous structure. The deswelling rate of porous hydrogels was 7 times larger than that of conventional hydrogels and increased with increasing the pore size of silica used. However, the swelling was not affected by the pore formation. The thermoresponsiveness of porous polyNIPAAm hydrogels could be regulated by the pore size. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3542–3547, 2002     

From poly(N‐isopropylacrylamide)‐block‐poly(ethylene oxide)‐block‐poly(N‐isopropylacrylamide) triblock copolymer to poly(N‐isopropylacrylamide)‐block‐poly(ethylene oxide) hydrogels: Synthesis and rapid deswelling and reswelling behavior of hydrogels

Poly(N‐isopropylacrylamide)‐block‐poly(ethylene oxide)‐block‐poly(N‐isopropylacrylamide) (PNIPAAm‐b‐PEO‐b‐PNIPAAm) triblock copolymer was synthesized via the reversible addition‐fragmentation chain transfer/macromolecular design via the interchange of xanthate (RAFT/MADIX) process with xanthate‐terminated poly(ethylene oxide) (PEO) as the macromolecular chain transfer agent. The successful synthesis of the ABA triblock copolymer inspired the preparation of poly(N‐isopropylacrylamide)‐block‐poly(ethylene oxide) (PNIPAAm‐b‐PEO) copolymer networks with N,N′‐methylenebisacrylamide as the crosslinking agent with the similar approach. With the RAFT/MADIX process, PEO chains were successfully blocked into poly(N‐isopropylacrylamide) (PNIPAAm) networks. The unique architecture of PNIPAAm‐b‐PEO networks allows investigating the effect of the blocked PEO chains on the deswelling and reswelling behavior of PNIPAAm hydrogels. It was found that with the inclusion of PEO chains into the PNIPAAm networks as midblocks, the swelling ratios of the hydrogels were significantly enhanced. Furthermore, the PNIPAAm‐b‐PEO hydrogels displayed faster response to the external temperature changes than the control PNIPAAm hydrogel. The accelerated deswelling and reswelling behaviors have been interpreted based on the formation of PEO microdomains in the PNIPAAm networks, which could act as the hydrophilic tunnels to facilitate the diffusion of water molecules in the PNIPAAm networks. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

SET‐LRP of N,N‐dimethylacrylamide and of N‐isopropylacrylamide at 25 °C in protic and in dipolar aprotic solvents

The single‐electron transfer living radical polymerization (SET‐LRP) of water‐soluble monomers, N,N‐dimethylacrylamide (DMA) and N‐isopropylacrylamide (NIPAM), initiated with 2‐methylchloropropionate (MCP) in dipolar aprotic and protic solvents is reported. The radical polymerization of acrylamides is characterized by higher rate constants of propagation and bimolecular termination than acrylates. Therefore, the addition of CuCl₂ is required to mediate deactivation in the early stages of the reaction. Through the use of Cu(0)‐wire/Me₆‐TREN catalysis, conditions were optimized to minimize the amount of externally added CuCl₂ required to maintain a linear evolution of molecular weight and narrow molecular weight distribution. By using less CuCl₂ additive, the amount of soluble copper species that must ultimately be removed from the reaction mixture is reduced. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1752–1763, 2010     

Investigation of drug release from thermo‐ and pH‐sensitive poly(N‐isopropylacrylamide/itaconic acid) copolymeric hydrogels

N‐Isopropylacrylamide/itaconic acid copolymeric hydrogels were prepared by irradiation of the ternary mixtures of N‐isopropylacrylamide/itaconic acid/water by γ‐rays at ambient temperature. The dependence of swelling properties and phase transitions on the comonomer concentration and temperature were investigated. The hydrogels showed both temperature and pH responses. The effect of comonomer concentration on the uptake and release behavior of the hydrogels was studied. Methylene blue (MB) was used as a model drug for the investigation of drug uptake and release behavior of the hydrogels. The release studies showed that the basic parameters affecting the drug release behavior of the hydrogels were pH and temperature of the solution. Copyright © 2004 John Wiley & Sons, Ltd.     

Preparation and separation function of N‐isopropylacrylamide copolymer hydrogels

In this paper, N‐isopropylacrylamide (NIPA) was synthesized by acrylonitrile and isopropanol. Poly(N‐isopropylacrylamide) (PNIPA) was prepared by a chemical method. The dependence of its swelling behavior on temperature was studied. Results showed that PNIPA hydrogel was a temperature‐sensitive gel. Its LCST (lower critical solution temperature) was about 32 °C, and its swelling ratio (at 20 °C) was about 17–18. Sodium acrylate (SA) and sodium methylacrylate (SMA) were copolymerized with NIPA respectively. Equilibrium swelling ratios of the copolymer hydrogels at lower temperature were two to three times that of PNIPA. The LCST of the copolymer hydrogels could be controlled between 32 and 45 °C by adjusting the content of SA or SMA. Kinetics of P(NIPA‐co‐SA) hydrogels, whether swelling or shrinking processes, were in good agreement with apparent second order kinetic equations. Several experiments were designed to separate aqueous bovine serum albumin solution using the hydrogels prepared above. The separation efficiency was about 80%. Copyright © 2000 John Wiley & Sons, Ltd.     

Effect of 1,4‐dioxane on synthesis of macroporous poly(N‐isopropylacrylamide) hydrogels

Thermosensitive Poly(N‐isopropylacrylamide) (PNIPA) hydrogels were synthesized by a free radical solution polymerization in three different ways. Normal hydrogels were prepared at room temperature and normal cryogels were prepared at subzero temperature. A cation surfactant dodecyl dimethyl benzyl ammonium bromide (DDBAB) was used during preparation of novel cryogels in freezing state. The response rates of normal hydrogels were very slow, whereas the rates of both normal and novel cryogels were very fast because of the macroporous structure of the cryogels. Mixed solvents which were composed of pure water and 1,4‐dioxane at various concentrations were used instead of pure water during the polymerization. The effects of the mixed solvent on morphology, swelling ratio, and deswelling/reswelling kinetics of the three kinds of hydrogels were investigated. For normal hydrogels and normal cryogels, there was no remarkable difference no matter the mixed solvent or pure water was used. However, the properties of the resulted novel cryogels were much different with the concentration of dioxane. Finally, the resulted hydrogels were used for concentrating emulsified paraffin. The different separation performance was attributed to the different structure of gel matrix. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6594–6603, 2008     

Novel temperature‐ and pH‐responsive graft copolymers composed of poly(L‐glutamic acid) and poly(N‐isopropylacrylamide)

A series of novel temperature‐ and pH‐responsive graft copolymers, poly(L ‐glutamic acid)‐g‐poly(N‐isopropylacrylamide), were synthesized by coupling amino‐semitelechelic poly(N‐isopropylacrylamide) with N‐hydroxysuccinimide‐activated poly(L ‐glutamic acid). The graft copolymers and their precursors were characterized, by ESI‐FTICR Mass Spectrum, intrinsic viscosity measurements and proton nuclear magnetic resonance (¹H NMR). The phase‐transition and aggregation behaviors of the graft copolymers in aqueous solutions were investigated by the turbidity measurements and dynamic laser scattering. The solution behavior of the copolymers showed dependence on both temperature and pH. The cloud point (CP) of the copolymer solution at pH 5.0–7.4 was slightly higher than that of the solution of the PNIPAM homopolymer because of the hydrophilic nature of the poly(glutamic acid) (PGA) backbone. The CP markedly decreased when the pH was lowered from 5 to 4.2, caused by the decrease in hydrophilicity of the PGA backbone. At a temperature above the lower critical solution temperature of the PNIPAM chain, the copolymers formed amphiphilic core‐shell aggregates at pH 4.5–7.4 and the particle size was reduced with decreasing pH. In contrast, larger hydrophobic aggregates were formed at pH 4.2. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4140–4150, 2008     

Synthesis and characterization of poly(N‐isopropylacrylamide) films by photopolymerization

A novel method used for the preparation of poly(N‐isopropylacrylamide) (PNIPAAm) films of varying crosslink density under homogeneous/heterogeneous conditions is described in this paper. Photopolymerization of the N‐isopropylacrylamide (NIPAAm) monomer in water (homogeneous at ～7°C and heterogeneous at ～40°C) or a mixture of water/ethanol (50:50, heterogeneous at ～7°C) was carried out using 1‐[4‐(2‐hydroxyethoxy)‐phenyl]‐2‐hydroxy‐2‐methyl‐1‐propane‐1‐one (hydrophilic) or 2‐hydroxy‐2‐methyl propiophenone (hydrophobic) photo‐initiator. In order to investigate the effect of temperature and crosslink density, polymerization was carried out at ～7°C [below lower critical soluble temperature (LCST)] and ～40°C (above LCST) using varying amounts of N,N′‐methylene bisacrylamide (BIS) ranging from 1–4 wt%. Degree of swelling (determined by optical microscopy), phase transition temperature [determined by differential scanning calorimetry (DSC)] as well as morphology (scanning electron microscopy) were found to be dependent on solvent system (homogeneous/heterogeneous), temperature of polymerization and crosslink density. Hydrogels prepared at ～7°C using hydrophobic photo‐initiator and water/ethanol (50:50) as solvent, showed much higher degree of swelling at all levels of crosslink density as compared to hydrogel prepared at ～7°C using hydrophilic photo‐initiator and water as solvent. Hydrogels were used for patterning which may find applications in microfluidic devices. Copyright © 2006 John Wiley & Sons, Ltd.     

Effect of the crosslinking level on the properties of temperature‐sensitive poly(N‐isopropylacrylamide) hydrogels

In this study, the effect of the level of crosslinking on the properties of poly(N‐isopropylacrylamide) (PNIPAAm) hydrogels was investigated in terms of their lower critical solution temperature (LCST), interior morphology, equilibrium swelling, and deswelling and swelling kinetics. The thermal analysis showed that PNIPAAm hydrogels, having a wide range of crosslinking levels, exhibited almost the same LCSTs, and this was different from what the conventional theory would have predicted. Scanning electron micrographs revealed that the interior network structure of the PNIPAAm matrix became more porous with an increase in the level of crosslinking. This more porous matrix provided numerous water channels for water diffusion in or out of the matrix and, therefore, an improved response rate to the external temperature changes during the deswelling process and the swelling process. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 582–593, 2003     

Organic–inorganic hybrid hydrogels involving poly(N‐isopropylacrylamide) and polyhedral oligomeric silsesquioxane: Preparation and rapid thermoresponsive properties

3‐Acryloxypropylhepta(3,3,3‐trifluoropropyl) polyhedral oligomeric silsesquioxane (POSS) was synthesized and used as a modifier to improve the thermal response rates of poly(N‐isopropylacrylamide) (PNIPAM) hydrogel. The radical copolymerization among N‐isopropylacrylamide (NIPAM), the POSS macromer and N,N′‐methylenebisacrylamide was performed to prepare the POSS‐containing PNIPAM cross‐linked networks. Differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) showed that the POSS‐containing PNIPAM networks displayed the enhanced glass transition temperatures (T_g's) and improved thermal stability when compared with plain PNIPAM network. The POSS‐containing PNIPAM hydrogels exhibited temperature‐responsive behavior as the plain PNIPAM hydrogels. It is noted that with the moderate contents of POSS, the POSS‐containing PNIPAM hydrogels displayed much faster response rates in terms of swelling, deswelling, and re‐swelling experiments than plain PNIPAM hydrogel. The improved thermoresponsive properties of hydrogels have been interpreted on the basis of the formation of the specific microphase‐separated morphology in the hydrogels, that is, the POSS structural units in the hybrid hydrogels were self‐assembled into the highly hydrophobic nanodomains, which behave as the microporogens and promote the contact of PNIPAM chains and water. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 504–516, 2009     

β‐Cyclodextrin hydrogel incorporating hydrophobically modified poly(N‐isopropylacrylamide) for a temperature‐dependent release

Hydrogels exhibiting a temperature‐dependent release were prepared by incorporating hydrophobically modified poly(N‐isopropylacrylamide) (HmPNIPAM) into β‐cyclodextrin hydrogels (β‐CD hydrogels). The specific loading of HmPNIPAM was about 0.0069 g HmPNIPAM/g β‐CD hydrogels. The incorporation of the polymer was qualitatively conformed by FT‐IR spectroscopy and SEM. The percent release of blue dextran in 24 hr at 20°C (about 77%) was markedly higher than those obtained at 35°C and 45°C (about 53 and 55%, respectively). At the higher temperatures, the volume of the hydrogel could decrease upon the thermal contraction of HmPNIPAM, leading to a smaller mesh and a suppressed release. In fact, the swelling ratio in 24 hr at 35°C and 45°C (about 396% and 405%, respectively) was obviously lower than that obtained at 20°C (about 465%). Copyright © 2011 John Wiley & Sons, Ltd.     

Multi‐Component Kinetic Modeling for Controlling Local Compositions in Thermosensitive Polymers

Summary: An explicit terminal copolymerization kinetic model accounting for the copolymerization of up to four different comonomers is developed and applied to model the conversion profiles and local compositional gradients in functionalized PNIPAM‐based polymer and hydrogel systems. The kinetics of the functional comonomer(s) have a large influence on both the mole fraction and chain distribution of functional groups in polymers. Strategies are developed to synthesize polymers with uniform compositions by applying semi‐batch techniques or via copolymerization of multiple monomers with the same target functionality but with divergent reactivities relative to NIPAM. Synthetic protocols are also designed to maximize the compositional uniformity and randomness of ampholytic polymers.

Instantaneous mole fractions of monomers in polymers as a function of the overall monomer conversion for the copolymerizations of NIPAM, MBA, and two functional monomers: MMA and acrylamide.     

The incorporation of carboxylate groups into temperature‐responsive poly(N‐isopropylacrylamide)‐based hydrogels promotes rapid gel shrinking

Aqueous gel deswelling rates for copolymer hydrogels comprising N‐isopropylacrylamide (IPAAm) and 2‐carboxyisopropylacrylamide (CIPAAm) in response to increasing temperatures were investigated. Compared with pure IPAAm‐based gels, IPAAm–CIPAAm gels shrink very rapidly in response to small temperature increases across their lower critical solution temperature (their volume is reduced by five‐sixths within 60 s). Shrinking rates for these hydrogels increase with increasing CIPAAm content. In contrast, structurally analogous IPAAm–acrylic acid (AAc) copolymer gels lose their temperature sensitivity with the introduction of only a few mole percent of AAc. Additionally, deswelling rates of IPAAm–AAc gels decrease with increasing AAc content. These results indicate that IPAAm–CIPAAm copolymer gels behave distinctly from IPAAm–AAc systems even if both comonomers, CIPAAm and AAc, possess carboxylic acid groups. Thus, we propose that the sensitive deswelling behavior for IPAAm–CIPAAm gels results from strong hydrophobic chain aggregation maintained between network polymer chains due to the similar chemical structures of CIPAAm and IPAAm. This structural homology facilitates aggregation of chain isopropylamide groups for both IPAAm and CIPAAm sequences with increasing temperature. The incorporation of AAc, however, shows no structural homology to IPAAm, inhibiting chain aggregation and limiting collapse. A functionalized temperature‐sensitive poly(N‐isopropylacrylamide) hydrogel containing carboxylic acid groups is possible with CIPAAm, producing rapid and large volume changes in response to smaller temperature changes. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 335–342, 2001     

Positron annihilation studies on radiation‐crosslinked poly(N‐isopropylacrylamide) hydrogels

The temperature‐sensitive poly(N‐isopropylacrylamide) hydrogels, prepared by γ and electron‐beam (EB) irradiation, were studied using positron annihilation lifetime spectroscopy (PALS). The effect of water content in the hydrogel on the ortho‐positronium (o‐Ps) lifetime and intensity was investigated. The observed positronium lifetime suggests microstructural differences between γ‐ and EB‐synthesized hydrogels. The distribution in positronium lifetime indicates nonhomogeneity in the distribution of free‐volume holes in EB‐synthesized hydrogels. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3462–3466, 2000