New liquid‐crystalline thermosets from liquid‐crystalline bisazomethynic epoxy resins with naphthylene disruptors in the central core

We synthesized novel epoxy‐terminated monomers on the basis of imine groups with spacers of different lengths between mesogens and reactive groups and examined their mesogenic properties. Their reaction with primary aromatic diamines and tertiary amines was carried out to investigate the formation of liquid‐crystalline thermosets. We explored how the curing conditions and the structures of the monomers and amines affected the formation of ordered networks. The special symmetry of a 1,5‐disubstituted naphthalene unit in the central core led to nematic mesophases in the pure liquid‐crystalline epoxy resins, and thermosets with locked nematic textures were obtained in all cases, regardless of the length of the spacer. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1536–1544, 2003     

Miscibility level and mechanical characterization of blends of two liquid‐crystalline polymers based on p‐hydroxybenzoic acid

Injection‐molded blends composed of two liquid‐crystalline polymers (LCPs) based on 60/40 p‐hydroxybenzoic acid/ethylene terephthalate (R3) and 73/27 p‐hydroxybenzoic acid/2,6‐hydroxynaphthoic acid (VA) copolymers, respectively, were obtained across the whole composition range. The two amorphous phases of the blends contained only slight amounts of the minority component, and the occurrence of some chemical reaction, mainly at high VA contents, was detected by Fourier transform infrared. Synergisms in the modulus of elasticity and in the tensile strength were seen in most of the blend compositions. The largest synergism was in the 50/50 R3/VA blend, which showed a modulus of elasticity 26% higher than that of either of the two components and a 17% positive deviation in the tensile strength with respect to the rule of mixtures. The different orientation of the LCPs in the blends explains the differences in the mechanical behavior. However, contrary to previous works on LCP blends and despite the almost complete immiscibility, the observed negative volume of mixing appears to be the main parameter that determines the synergistic mechanical behavior. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1022–1032, 2003     

Photoreactive main‐chain liquid‐crystalline polyesters: Synthesis,characterization, and photochemistry

Three series of semiflexible and rigid main‐chain polyesters containing photoreactive mesogenic units derived from p‐phenylenediacrylic acid (PDA) and cinnamic acid have been synthesized by high‐temperature polycondensation. The thermal and mesomorphic properties of the polymers have been determined. The photochemical behavior of polymer P‐[1]‐T, which contains a PDA unit, has been studied both in solution and in films. In solution, [2+2] photocycloaddition, E/Z photoisomerization, and photo‐Fries rearrangement can take place. In contrast, the dominant process in spin‐coated films is the [2+2] photocycloaddition reaction, which causes crosslinking of the polymer. In films, the photochemistry and induction of anisotropy are strongly influenced by the aggregation of the PDA phenylester unit. A dichroism of about 0.2 has been induced in films by irradiation with linearly polarized UV light, and thus the capability of these films to induce optical anisotropy and align liquid crystals has been demonstrated. Liquid‐crystalline cells have been made with polarized irradiated films of P‐[1]‐T as aligning layers. A commercial liquid‐crystalline mixture has been used for this study, and a similar liquid‐crystalline order determined by polarized Fourier transform infrared to a commercial cell with rubbed polyimide as an aligning layer has been detected. Because of crosslinking of the irradiated P‐[1]‐T photoaligning layer, the photoinduced anisotropy is stable at high temperatures, and the liquid‐crystalline molecules are insoluble in the irradiated polymer. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4907–4921, 2005     

Liquid‐crystalline thermosets from liquid‐crystalline epoxy resins containing bisazomethinebiphenylene mesogens in the central core: Copolymerization with a nonmesomorphic epoxy resin

A new series of liquid‐crystalline epoxy resins was synthesized, and their mesomorphic behavior was investigated with differential scanning calorimetry, polarized optical microscopy, and wide‐angle X‐ray scattering. These glycidylic compounds had central aromatic imine mesogens derived from benzidine and aliphatic spacers of up to 10 methylene units that linked the mesogens to the glycidylic groups. Crosslinking these monomers with primary aromatic diamines led to nematic networks, some of which contained crystal inclusions. However, through curing with tertiary amines as catalytic agents or through copolymerization with different proportions of the nonmesomorphic epoxy monomer and primary amines as crosslinking agents, smectic C organized thermosets were prepared when the spacers had at least four methylene carbons. When they had fewer than four, the networks were nematic. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3631–3643, 2004     

Anisotropic thermosets from liquid‐crystalline azomethynic epoxy resins and primary aromatic diamines

Novel epoxy‐terminated monomers based on imine groups were synthesized and their mesogenic properties studied. Aliphatic spacers of different lengths were introduced between the rigid unit and the glycidylic group, and their liquid‐crystalline behavior was examined. They were reacted with primary aromatic diamines inside a magnetic field so that the formation of anisotropic networks could be investigated. The influence of curing conditions and the structure of monomers and amines on the formation of liquid‐crystal thermosets were investigated. Thermosets with locked nematic textures were obtained in all cases. The influence of a 7.1 T magnetic field on the macroscopic orientation of these materials was studied, and mechanical properties of the resulting networks were evaluated by dynamic mechanical analysis. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1–12, 2003     

Novel side‐chain liquid‐crystalline polyimide for film materials

A novel side‐chain liquid‐crystalline polyimide (SLCPI) was prepared via copolycondensation from 3,5‐diamino‐benzonic‐4′‐biphenyl ester, 4,4′‐diamino‐ biphenyl ether, and 3,3′,4,4′‐oxydiphthalic dianhydride. The energy‐minimized structure and liquid crystallinity of SLCPI were investigated by molecular modeling, differential scanning calorimetry (DSC), wide‐angle X‐ray scattering, and polarized optical microscopy, respectively. The results indicated that this polyimide (PI) with side‐chain mesogenic units exhibited a nematic NI phase. Because of the in situ self‐reinforcement of side‐chain mesogenic units, the improved tensile strength and modulus of PI films reached 270% and 300%, respectively. The coefficient of thermal expansion of films decreased by 40%. DSC and thermogravimetric analyses indicated that the phase‐transition temperature of SLCPI was above 240 °C, and the 5% weight‐loss temperature was above 520 °C. Moreover, copolycondensation of two diamines with dianhydride and incorporation of pendent mesogenic units diminished the regularity and symmetry of main chains; as a result, SLCPI exhibits good film processability. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 554–559, 2003     

Synthesis and crosslinking of biphenyl and naphthalene liquid‐crystalline polyethers with pendant full‐saturated and vinyl‐terminated aliphatic chains

Two series of vinyl‐terminated, side‐chain liquid‐crystalline polyethers containing 4,4′‐biphenyl and 2,6‐naphthalene moieties as mesogenic cores with several contents of vinyl crosslinkable groups were synthesized by chemically modifying poly(epichlorohydrin) with mixtures of saturated and vinyl‐terminated mesogenic acids. In most cases the degree of modification was over 90%. The polymers were characterized by chlorine analysis, IR and ¹H and ¹³C NMR spectroscopies, viscometry, size exclusion chromatography/multi‐angle laser light scattering, and thermogravimetric analysis. The liquid‐crystal behavior of all the synthesized polymers was examined by differential scanning calorimetry, polarized optical microscopy (POM), and X‐ray diffraction on mechanically oriented samples. The crosslinking of most polymers was done by peroxide‐type initiators, which generally led to liquid‐crystal elastomers. The mesophase organization was maintained on the crosslinked materials, as confirmed by POM and X‐ray diffraction. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3384–3399, 2003     

Main‐chain viologen polymers with triflimide counterion exhibiting lyotropic liquid‐crystalline properties in polar organic solvents

The solution‐phase behavior of three main‐chain viologen polymers, which are composed of isomeric xylyl units and triflimide as a counterion, was studied in methanol, dimethylformamide, acetonitrile, and dimethyl sulfoxide as solvents microscopically under crossed polarizers. Each of them exhibited a lyotropic lamellar phase in both polar protic and aprotic solvents. Their C^* for the formation of biphasic solutions (1–5 wt %) and concentrations (20–30 wt %) for the lyotropic solutions in methanol was much lower than those in polar aprotic solvents (20–71 and 60–81 wt %, respectively). Their high solubility, high C^* for the formation of biphasic solutions, and high concentrations for the formation of lyotropic solutions in polar aprotic solvents were related to the significant reduction of strong ionic interactions between triflimide and 4,4′‐bipyridinium ions in each of these viologen polymers. They were the first examples of viologen polymers that exhibited a lyotropic phase in polar aprotic solvents. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2015–2024, 2002     

Liquid‐crystalline thermosets by the curing of dimeric liquid‐crystalline epoxyimine monomers with 2,4‐toluene diisocyanate

We studied the curing processes of several series of dimeric liquid‐crystalline epoxyimine monomers with 2,4‐toluene diisocyanate (TDI) alone or with added catalytic proportions of 4‐(N,N‐dimethylamino)pyridine. We obtained isotropic materials or liquid‐crystalline thermosets with different degrees of order, which depended on the structures of the monomers. To fix ordered networks, we had to do the curing in two steps when TDI was used alone as the curing agent. However, when a tertiary amine was added in catalytic proportions, the ordered networks were fixed in just one step. In this way, we were able to fix both nematic and smectic mesophases. The significance of the polarization of the mesogen for obtaining liquid‐crystalline thermosets was demonstrated. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2521–2530, 2003     

Fracture toughness and fracture mechanism of liquid‐crystalline epoxy resins with different polydomain structures

Liquid‐crystalline (LC) epoxy resins were cured at different temperatures to obtain polydomain LC phase–cured resins. The cured resins had polydomain structures with a nematic LC phase and their domain diameters differed depending on the curing temperatures. The relationship between the domain diameter and fracture toughness of the diglycidyl ether of terephthalylidene‐bis‐(4‐amino‐3‐methylphenol) (DGETAM)/m‐phenylenediamine (m‐PDA) systems with the nematic phase and the previously reported smectic LC phase structures was investigated. It was clarified that the highly ordered LC structure (smectic phase) in each domain could improve the fracture toughness. In addition, the changes in the network orientation of the DGETAM/m‐PDA systems were evaluated by a mapping of the microscopic infrared dichroism in the fracture process and their toughening mechanism was suggested. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Synthesis and characterization of new segmented polyurethanes with side‐chain,liquid‐crystalline chain extenders

Liquid‐crystalline, segmented polyurethanes with methoxy–biphenyl mesogens pendant on the chain extender were synthesized by the conventional prepolymer technique and esterification reaction. Two, side‐chain, liquid‐crystalline (SCLC) polyurethanes with mesogens having spacers of six and eight methylene units were prepared. The structures of the mesogenic units and SCLC polyurethanes were confirmed by Fourier transform infrared spectroscopy and ¹H NMR. Polymer properties were also examined by solubility tests, water uptakes, and inherent viscosity measurements. Differential scanning calorimetry studies indicated that the transition temperature of the isotropic to the liquid‐crystalline phase decreased with increasing spacer length. Wide‐angle X‐ray diffraction (WAXD) studies revealed the existence of liquid‐crystalline phases for both SCLC polyurethanes. Polarized optical microscopic investigations further confirmed the thermotropic liquid‐crystalline behaviors and nematic mesophases of both samples. Thermogravimetric analysis displayed better thermal stabilities for both SCLC polymers and indicated that the presence of mesogenic side chains may increase the thermal stability of segmented polyurethanes. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 290–302, 2004     

Dimeric liquid‐crystalline epoxyimine monomers: Influence of dipolar moments on mesomorphic behavior and the formation of liquid‐crystalline thermosets

We examine some of the structural aspects that influence the mesomorphic behavior of liquid‐crystalline dimeric epoxy resins with imine groups in the mesogens. We synthesized two new series of monomers and compared them with previously synthesized monomers. Compared with previously studied series, the imine group in the new monomers is oriented differently with respect to the ether and ester groups linked to the end of the mesogenic unit. Our results confirmed the importance of polarization of the mesogenic groups and the presence of an ester group in the inner position in the formation of smectic mesophases. By curing with primary and tertiary amines, we demonstrate that these two requirements are necessary if liquid‐crystalline thermosets are to be obtained with different degrees of order. These studies were carried out with differential scanning calorimetry, polarized optical microscopy, and X‐ray diffraction. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1465–1477, 2003     

Lyotropic liquid‐crystalline behavior of polyisocyanodipeptides

Rigid, helical polyisocyanodipeptides derived from alanine (PIAAs) that form lyotropic liquid‐crystalline (LC) phases in tetrachloroethane are presented. An investigation by optical microscopy between crossed polarizers demonstrated that PIAAs prepared by the polymerization of isocyanodipeptide monomers with an activated tetrakis isocyanide nickel(II) catalyst could form cholesteric LC phases in tetrachloroethane in concentrations between 18 and 30 wt %. Cholesteric LC phases that were formed in solutions of greater than 25 wt % displayed a reversal of the cholesteric helix upon annealing at 50 °C. Diastereomeric PIAA mixtures displayed cholesteric LC behavior only when the PIAAs had the same helix screw sense. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 981–988, 2007     

Synthesis and crosslinking of a series of dimeric liquid‐crystalline diglycidylester compounds containing imine groups

We used readily available commercial reagents and well‐known procedures to synthesize a series of aromatic imine mesogenic diglycidylester compounds with dimeric architectures. The compounds obtained were characterized by spectroscopic techniques. Their liquid‐crystalline behavior was examined by differential scanning calorimetry, hot‐stage polarized optical microscopy (POM), and wide‐angle X‐ray scattering (WAXS) and related to the different structures that varied in the length of the central spacer. All the compounds exhibited nematic mesophases with the exception of the dimer with a three‐methylene central spacer that did not reveal liquid‐crystalline character. We investigated the crosslinking of the synthesized compounds and obtained liquid‐crystalline thermosets (LCTs) with several primary aromatic diamines in stoichiometric ratios or a tertiary amine as a catalyst. The curing processes were measured by calorimetry, and the thermal stability of the LCTs was evaluated by thermogravimetry. The ordered character of the LCTs was confirmed by POM and WAXS. Finally, the mechanical characterization of the LCTs obtained was examined by dynamic mechanical thermal analysis. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4344–4356, 2002     

Synthesis and phase behavior of side‐chain liquid‐crystalline polymers containing malachite green lactone groups

New side‐chain liquid‐crystalline polymers containing both cholesteric and thermochromic side groups were synthesized. Their chemical structures were confirmed with elemental analyses and Fourier transform infrared, proton nuclear magnetic resonance, and carbon‐13 nuclear magnetic resonance spectra. The mesogenic properties and phase behavior were investigated with differential scanning calorimetry, thermogravimetric analysis, polarizing optical microscopy, and X‐ray diffraction measurements. The effect of the concentration of dye side groups on the phase behavior of the polymers was examined. The polymers showed smectic or cholesteric phases. Those polymers containing less than 20 mol % dye groups had good solubility, reversible phase transitions, wider mesophase temperature ranges, and higher thermal stability. The experimental results demonstrated that the isotropization temperature and mesophase temperature ranges decreased with an increasing concentration of dye groups. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3870–3878, 2004     

Main‐chain,thermotropic, liquid‐crystalline,hydrogen‐bonded polymers of 4,4′‐bipyridyl with aliphatic dicarboxylic acids

A series of main‐chain, thermotropic, liquid‐crystalline (LC), hydrogen‐bonded polymers or self‐assembled structures based on 4,4′‐bipyridyl as a hydrogen‐bond acceptor and aliphatic dicarboxylic acids, such as adipic and sebacic acids, as hydrogen‐bond donors were prepared by a slow evaporation technique from a pyridine solution and were characterized for their thermotropic, LC properties with a number of experimental techniques. The homopolymer of 4,4′‐bipyridyl with adipic acid exhibited high‐order and low‐order smectic phases, and that with sebacic acid exhibited only a high‐order smectic phase. Like the homopolymer with adipic acid, the two copolymers of 4,4′‐bipyridyl with adipic and sebacic acids (75/25 and 25/75) also exhibited two types of smectic phases. In contrast, the copolymer of 4,4′‐bipyridyl with adipic and sebacic acids (50/50), like the homopolymer with sebacic acid, exhibited only one high‐order smectic phase. Each of them, including the copolymers, had a broad temperature range of LC phases (36–51 °C). The effect of copolymerization for these hydrogen‐bonded polymers on the thermotropic properties was examined. Generally, copolymerization increased the temperature range of LC phases for these polymers, as expected, with a larger decrease in the crystal‐to‐LC transition than in the LC‐to‐isotropic transition. Additionally, it neither suppressed the formation of smectic phases nor promoted the formation of a nematic phase in these hydrogen‐bonded polymers, as usually observed in many thermotropic LC polymers. The thermal transitions for all of them, measured by differential scanning calorimetry, were well below their decomposition temperatures, as measured by thermogravimetric analysis, which were in the temperature range of 193–210 °C. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1282–1295, 2003     

High‐molecular‐weight side‐chain liquid‐crystalline polyethers based on 4′‐cyanobiphenyl‐4‐oxy mesogenic groups

A set of poly[ω‐(4′‐cyano‐4‐biphenyloxy)alkyl‐1‐glycidylether]s were synthesized by the chemical modification of the corresponding poly(ω‐bromoalkyl‐1‐glycidylether)s with the sodium salt of 4‐cyano‐4′‐hydroxybiphenyl. New high‐molecular‐weight side‐chain liquid‐crystalline polymers were obtained with excellent yield and almost quantitative degree of modification. All side‐chain liquid‐crystalline polymers were rubbers soluble in tetrahydrofuran. The characterization by ¹H and ¹³C NMR revealed no changes in the regioregular isotactic microstructure of the starting polymer and the absence of undesirable side reactions such as deshydrobromination. The liquid crystalline behavior was analyzed by DSC and polarized optical microscopy, and mesophase assignments were confirmed by X‐ray diffraction. Polymers that had alkyl spacers with n = 2 and 4 were nematic, those that had spacers with n = 6 and 8 were nematic cybotactic, and those that had longer spacers (n = 10 and 12) were smectic C and showed some crystallization of the side alkyl chains. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3002–3012, 2004     

Synthesis,photochemical and phase behavior of linear and hyperbranched photoactive benzylidene liquid‐crystalline polyesters

Photoactive hyperbranched benzylidene liquid‐crystalline polyester (PAHBP) and photoactive linear benzylidene liquid‐crystalline polyester (PALBP) were synthesized by solution polycondensation with pyridine as an acid acceptor. PAHBP and PALBP were thoroughly characterized with Fourier transform infrared, ¹H and ¹³C NMR, ultraviolet–visible spectrophotometry, fluorescent spectrophotometry, gel permeation chromatography, thermogravimetric analysis, differential scanning calorimetry, and polarized optical microscopy. Both polymers exhibited nematic mesophase. The glass‐transition temperature and liquid‐crystalline isotropic temperature of PAHBP were higher than those of PALBP. During photolysis under ultraviolet light, both polymers underwent an intermolecular photocycloaddition reaction, and the photoactivity of PAHBP was faster than that of PALBP; this was further confirmed by photoviscosity studies. PALBP and PAHBP were fluorescent in nature. An increase in the fluorescence intensity with the time of ultraviolet‐light irradiation was observed for both PAHBP and PALBP. The rate of increase in the fluorescence intensity of the linear analogue (PALBP) was higher than that of the hyperbranched polymer (PAHBP). This behavior could be attributed to the attainment of better planarity in the case of the linear one but not in the case of PAHBP because of the rapid crosslinking of PAHBP leading to an irregular architecture. This behavior was further confirmed by the calculation of the steric energy from corresponding model compounds. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3986–3994, 2006     

Interfacial slip at the thermotropic liquid‐crystalline polymer/poly (ethylene naphthalate) interface

The unique rheological properties of a thermotropic liquid‐crystalline polymer (TLCP) were first studied. The thermal and shear history of the TLCP was found to play a critical role in its rheological properties. Crystallites were observed in the TLCP melt even above the melting temperature detected by differential scanning calorimetry. Because interfacial slip had long been suggested as an important reason for viscosity reduction in TLCP/thermoplastic blends, for the first time, interfacial slip at the TLCP/poly(ethylene naphthalate) (PEN) interface was investigated with an energy model. The model quantified the degree of interfacial slip at the TLCP/PEN interface by an energy factor. The calculated energy factors revealed a high degree of interfacial slip at the TLCP/PEN interface. It was proposed that the high rigidity of rodlike TLCP chains and their alignment parallel to the interface prevented mutual entanglements at the TLCP/PEN interface. The lack of mutual entanglements promoted the interfacial slip. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 302–315, 2004     

Synthesis of a novel hybrid liquid‐crystalline rod–coil diblock copolymer

A series of novel rod–coil diblock copolymers on the basis of mesogen‐jacketed liquid‐crystalline polymer were successfully prepared by atom transfer radical polymerization from the flexible polydimethylsiloxane (PDMS) macroinitiator. The hybrid diblock copolymers, poly{2,5‐bis[(4‐methoxyphenyl)oxycarbonyl]styrene}‐block‐polydimethylsiloxane, had number‐average molecular weights (M_n's) ranging from 9500 to 30,900 and relatively narrow polydispersities (≤1.34). The polymerization proceeded with first‐order kinetics. Data from differential scanning calorimetry validated the microphase separation of the diblock copolymers. All block copolymers exhibited thermotropic liquid‐crystalline behavior except for the one with M_n being 9500. Four liquid‐crystalline diblock copolymers with PDMS weight fractions of more than 18% had two distinctive glass‐transition temperatures. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1799–1806, 2003