Preparation of poly(styrene‐co‐acrylonitrile)‐grafted multiwalled carbon nanotubes via surface‐initiated atom transfer radical polymerization

The in situ grafting‐from approach via atom transfer radical polymerization was successfully applied to polystyrene, poly(styrene‐co‐acrylonitrile), and polyacrylonitrile grafted onto the convex surfaces of multiwalled carbon nanotubes (MWCNTs) with (2‐hydroxyethyl 2‐bromoisobutyrate) as an initiator. Thermogravimetric analysis showed that effective functionalization was achieved with the grafting approach. The grafted polymers on the MWCNT surface were characterized and confirmed with Fourier transform infrared spectroscopy and nuclear magnetic resonance. Raman and near‐infrared spectroscopy revealed that the grafting of polystyrene, poly(styrene‐co‐acrylonitrile), and polyacrylonitrile slightly affected the side‐wall structures. Field emission scanning electron microscopy showed that the carbon nanotube surface became rough because of the grafting of the polymers. Differential scanning calorimetry results indicated that the polymers grafted onto MWCNTs showed higher glass‐transition temperatures. The polymer‐grafted MWCNTs exhibited relatively good dispersibility in an organic solvent such as tetrahydrofuran. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 460–470, 2007     

Tailor‐made poly(ethyl acrylate) by atom transfer radical polymerization

Atom transfer radical polymerization (ATRP) of ethyl acrylate (EA) was carried out using different initiators, CuBr or CuCl as catalyst in combination with different ligands e.g., 2,2′‐bipyridine (bpy) and N,N,N′,N″N″‐pentamethyl diethylenetriamine (PMDETA). Use of PMDETA as ligand resulted in faster polymerization rate (95% conversion in 15 min) than those using bipyridine (～58% conversion in 10.5 h). This is due to the lower reduction potential of copper‐amine than that of copper‐bpy complex, resulting in higher rates of activation of dormant halides. Use of ethylene carbonate as solvent lead to faster polymerization rate and better control in polymerization when compared with p‐xylene as solvent. The reaction temperature had a positive effect on polymerization rate and the optimum reaction temperature was found to be 90 °C. An apparent enthalpy of activation of ～85 kJ/mol was determined for the ATRP of ethyl acrylate, corresponding to an enthalpy of equilibrium of ～64 kJ/mol. By judicious choice of the reaction parameters it was possible to tailor the end group of the final polymer. MALDI‐TOF‐MS analysis and the chain extension experiment of poly(ethyl acrylate) (PEA) prepared using bpy as ligand showed the presence of ? Br as the end group. On the contrary, when PMDETA was used as the ligand, the mass spectra analysis showed hydrogen terminated polymer as the major species towards the end of polymerization. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1661–1669, 2007     

Grafting of polymethyl methacrylate from poly(ethylene-co-vinylacetate) copolymer using atom transfer radical polymerization

Atom transfer radical polymerization was employed for the first time to prepare graft copolymer having by ethylene-vinyl acetate (EVA) copolymer as backbone and poly(methyl methacrylate) (PMMA) as branches. The polymerization of MMA was initiated by EVA carrying chloropropionate groups as macroinitiator, in the presence of copper chloride (CuCl) and bipyridine (bpy) at 80 °C. The macroinitiator was prepared by esterification of partially hydrolyzed EVA with 2-chloropropionyl chloride. Successful graft copolymerizations were performed both in toluene/γ-butyrolactone mixed solvent and in toluene solution, with grafting efficiency of 12% and 6%, respectively. Molecular weight distribution of the PMMA segments around 1.2 has been achieved with pure toluene solution. The ATRP graft copolymerization was supported by an increase of the molecular weight of the graft copolymers, as compared to that of the macroinitiator and also by their monomodal molecular weight distribution.     

Graft polymerization of 2-hydroxyethyl methacrylate via ATRP with poly(acrylonitrile-co-p-chloromethyl styrene) as a macroinitiator

Amphiphilic graft copolymers are excellent additives for the development of antifouling membranes by nonsolvent induced phase separation. We report a convenient approach to the synthesis of novel graft copolymers with hydrophobic polyacrylonitrile (PAN) backbones and hydrophilic poly(2-hydroxyethyl methacrylate) (PHEMA) side chains. Atom transfer radical polymerization (ATRP) of 2-hydroxyethyl methacrylate was carried out with poly(acrylonitrile-co-p-chloromethyl styrene) (PAN-co-PCMS) as a macroinitiator in the presence of CuCl/2,2’-bipyridine at 50 °C in dimethyl sulfoxide. Kinetics of the graft polymerization was also evaluated. The synthesis of poly(acrylonitrile-co-p-chloromethyl styrene-g-2-hydroxyethyl methacrylate) (PAN-co-(PCMS-g-PHEMA)) can be relatively controlled when CMS (the ATRP sites) unit in the macroinitiator is around 5 mol%. Both the macroinitiators and graft copolymers were characterized by FTIR, NMR and GPC. The surface morphology and wettability of the copolymer films were studied by AFM and water contact angle measurement, respectively. We demonstrate that phase segregation between the PAN-co-PCMS backbones and the PHEMA side chains takes place and the surface hydrophilicity of the graft copolymers increases with the length of the PHEMA side chains. Because these amphiphilic graft copolymers can be synthesized in mass, they will be useful as latent additives for the fabrication of advanced PAN separation membranes.     

A novel poly(p‐phenylene) containing alternating poly(perfluorooctylethyl acrylate‐co‐methyl methacrylate) and polystyrene grafts by combination of atom transfer radical polymerization and Suzuki coupling processes

A poly(p‐phenylene) (PP), carrying perfectly alternating, well‐defined poly(perfluorooctylethyl acrylate‐co‐methyl methacrylate) [P(FEA‐co‐MMA)] and polystyrene (PS) side chain grafts, was synthesized by the combination of atom transfer radical polymerization (ATRP) and Suzuki cross‐coupling processes. First, dibromobenzene and diboronic ester functional macromonomers of P(FEA‐co‐MMA) and PS, respectively, were prepared by ATRP. In the second step, PP with lateral alternating P(FEA‐co‐MMA) and PS chains was synthesized by a Suzuki coupling reaction in the presence of Pd(PPh₃)₄ catalyst. The wetting behavior of the polymers was studied by measurements of the static contact angle θ of thin films (200?400 nm thickness) using water and n‐hexadecane as wetting liquids. The obtained fluorinated PP showed high static contact angles with both interrogating liquids, exhibiting simultaneously hydrophobic (θ_w = 111°) and lipophobic (θ_h = 67°) properties. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Grafting of montmorillonite nano‐clay with butyl acrylate and methyl methacrylate by atom transfer radical polymerization: Blends with poly(BuA‐co‐MMA)

11‐(2‐Bromo‐2‐methyl)propionyl‐oxy‐undecyl trichlorosilane atom transfer radical polymerization (ATRP) initiator was covalently attached on montmorillonite clay platelets via silylation reactions. The initiator clay was used to polymerize butyl acrylate (BuA) and methyl methacrylate (MMA) on the clay surface. Polymerization was performed in bulk monomer solution or in DMSO. Polymer modified clay was mixed with a poly(BuA‐co‐MMA) matrix. Small angle X‐ray scattering (SAXS) and transmission electron microscopy (TEM) showed that clay modified in DMSO gave exfoliated composites when mixed with the matrix copolymer. Mechanical properties of the composites were studied by dynamic mechanical thermal analysis (DMTA). The results showed that the mechanical properties were improved as a function of clay content, as well with an increasing homogeneity of the nanocomposite. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3086–3097, 2009     

Synthesis and characterization of poly(methyl methacrylate)‐block‐poly(methylphenylsilane)‐ block‐poly(methyl methacrylate) by atom transfer radical polymerization

ABA block copolymers of methyl methacrylate and methylphenylsilane were synthesized with a methodology based on atom transfer radical polymerization (ATRP). The reaction of samples of α,ω‐dihalopoly(methylphenylsilane) with 2‐hydroxyethyl‐2‐methyl‐2‐bromoproprionate gave suitable macroinitiators for the ATRP of methyl methacrylate. The latter procedure was carried out at 95 °C in a xylene solution with CuBr and 2,2‐bipyridine as the initiating system. The rate of the polymerization was first‐order with respect to monomer conversion. The block copolymers were characterized with ¹H NMR and ¹³C NMR spectroscopy and size exclusion chromatography, and differential scanning calorimetry was used to obtain preliminary evidence of phase separation in the copolymer products. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 30–40, 2003     

Reverse atom transfer radical polymerization of methyl methacrylate initiated by p‐chlorobenzenediazonium tetrafluoroborate

The controlled polymerization of methyl methacrylate (MMA) in bulk was initiated with p‐chlorobenzenediazonium tetrafluoroborate ( 1 ) and Cu(II) or Cu(I)/Cu(II)/N,N,N′,N″,N″‐pentamethyldietylene triamine (PMDETA) complex system at various temperatures (20, 60, and 90 °C). The proposed polymerization mechanism is based on the Meerwein‐type arylation reaction followed by a reverse atom transfer radical polymerization. In this mechanism, aryl radicals formed by the reaction with 1 and Cu(I) and/or PMDETA initiated the polymerization of MMA. The polymerization is controlled up to a molecular weight of 46,000 at 90 °C. Chain extension was carried out to confirm the controlled manner of the polymerization system. In all polymerization systems, the polydispersity index and initiator efficiency ranged from 1.10–1.57 to 0.10–0.21, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2019–2025, 2003     

Functionalization of iron oxide magnetic nanoparticles with poly(methyl methacrylate) brushes via grafting‐from atom transfer radical polymerization

A key problem with nanomaterials is the difficulty of controlling the dispersion of nanoparticles inside an organic medium. To overcome this problem, functionalization of the nanoparticle surface is required. Poly(methyl methacrylate) (PMMA) brushes were grown on the surface of iron oxide magnetic nanoparticles with atom transfer radical polymerization and a grafting‐from approach. Modified magnetic nanoparticles with a graft density of 0.1 PMMA chains/nm² were obtained. Cu(II), used as a deactivating complex, allowed good control of the polymerization along with a narrow polydispersity of the polymer chains. The functionalized magnetic nanoparticles were characterized with Fourier transform infrared spectroscopy, thermogravimetric analysis, gel permeation chromatography, and atomic force microscopy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 925–932, 2007     

Titanium tetrachloride supported on atom transfer radical polymerized poly(methyl acrylate‐co‐1‐octene) as catalyst for ethylene polymerization

Ethylene polymerizations were performed using catalyst based on titanium tetrachloride (TiCl₄) supported on synthesized poly(methyl acrylate‐co‐1‐octene) (PMO). Three catalysts were synthesized by varying TiCl₄/PMO weight ratio in chlorobenzene resulting in incorporation of titanium in different percentage as determined by UV‐vis spectroscopy. The coordination of titanium with the copolymer matrix was confirmed by FTIR studies. The catalysts morphology as observed by SEM was found to be round shaped with even distributions of titanium and chlorine on the surface of catalyst. Their performance was evaluated for atmospheric polymerization of ethylene in n‐hexane using triethylaluminum as cocatalyst. Catalyst with titanium incorporation corresponding to 2.8 wt % showed maximum activity. Polyethylenes obtained were characterized for melting temperature, molecular weight, morphology and microstructure. The polymeric support utilized for TiCl₄ was synthesized using activators regenerated by electron transfer (ARGET) Atom Transfer Radical Polymerization (ATRP) of methyl acrylate (MA) and 1‐octene (Oct) with Cu(0)/CuBr₂/tris(2‐(dimethylamino)ethyl)amine (Me₆TREN) as catalyst and ethyl 2‐bromoisobutyrate (EBriB) as initiator at 80 °C. The copolymer poly(methyl acrylate‐1‐octene; PMO) obtained showed monomodal curve in Gel Permeation Chromatography (GPC) with polydispersity of 1.37 and copolymer composition (¹H NMR; F_MA) of 0.75. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7299–7309, 2008     

Controlled/living polymerization of 2‐(diethylamino)ethyl methacrylate and its block copolymer with tert‐butyl methacrylate by atom transfer radical polymerization

Polymerization of 2‐(diethylamino)ethyl methacrylate (DEAEMA) via homogeneous atom transfer radical polymerization under various reaction conditions is described. The effects of the initiators and solvents were examined. With 1,1,4,7,10,10‐hexamethyl triethylenetetramine/copper(I) chloride/p‐toluenesulfonyl chloride as the ligand/catalyst/initiator system in methanol, poly(DEAEMA) with a polydispersity index as low as 1.07 was synthesized. Kinetic studies demonstrated the polymerization was very well controlled and exhibited the living characteristic of the process. Well‐defined block copolymers of DEAEMA and tert‐butyl methacrylate (tBMA) were successfully synthesized. The copolymers could be synthesized with equally good results by starting with either p(DEAEMA) or p(tBMA) as the macroinitiators. However, only the macroinitiators terminated with chlorine should be used. The corresponding macroinitiators with bromine as a transferable group did not yield well‐defined copolymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2688–2695, 2003     

Controlled grafting of ethyl cellulose with azobenzene‐containing polymethacrylates via atom transfer radical polymerization

Graft copolymers of ethyl cellulose with azobenzene‐containing polymethacrylates were synthesized through atom transfer radical polymerization (ATRP). The residual hydroxyl groups on ethyl cellulose were first esterified with 2‐bromoisobutyryl bromide to yield 2‐bromoisobutyryloxy groups, which was then used to initiate the polymerization of 6‐[4‐(4‐methoxyphenylazo)phenoxy]hexyl methacrylate (MMAzo) in the presence of CuBr/N,N,N′,N″,N″‐pentamethylenetriamine (PMDETA) as catalyst and anisole as solvent. The graft copolymers were characterized by gel permeation chromatography (GPC) and ¹H‐NMR. The molecular weights of the graft copolymers increased relatively to the macroinitiator, and the polydispersities were narrow. The thermal and liquid crystalline property of the graft copolymers were investigated by differential scanning calorimeter (DSC) and polarizing optical microscope (POM). Photoresponsive property was studied under the irradiation of UV–vis light in THF solution. The graft copolymers have potential applications, including sensors and optical materials. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1653–1660, 2007     

Synthesis of coil‐comb block copolymers containing polystyrene coil and poly(methyl methacrylate) side chains via atom transfer radical polymerization

A series of polystyrene‐b‐(poly(2‐(2‐bromopropionyloxy) styrene)‐g‐poly(methyl methacrylate)) (PS‐b‐(PBPS‐g‐PMMA)) and polystyrene‐b‐(poly(2‐(2‐bromopropionyloxy)ethyl acrylate)‐g‐poly(methyl methacrylate)) (PS‐b‐(PBPEA‐g‐PMMA)) as new coil‐comb block copolymers (CCBCPs) were synthesized by atom transfer radical polymerization (ATRP). The linear diblock copolymer polystyrene‐b‐poly(4‐acetoxystyrene) and polystyrene‐b‐poly(2‐(trimethylsilyloxy)ethyl acrylate) PS‐b‐P(HEA‐TMS) were obtained by combining ATRP and activators regenerated by electron transfer (ARGET) ATRP. Secondary bromide‐initiating sites for ATRP were introduced by liberation of hydroxyl groups via deprotection and subsequent esterification reaction with 2‐bromopropionyl bromide. Grafting of PMMA onto either the PBPS block or the PBPEA block via ATRP yielded the desired PS‐b‐(PBPS‐g‐PMMA) or PS‐b‐(PBPEA‐g‐PMMA). ¹H nuclear magnetic resonance spectroscopy and gel permeation chromatography data indicated the target CCBCPs were successfully synthesized. Preliminary investigation on selected CCBCPs suggests that they can form ordered nanostructures via microphase separation. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2971–2983     

Towards more controlled poly(n-butyl methacrylate) by atom transfer radical polymerization

The homogeneous controlled/‘living’ free radical polymerization of n-butyl methacrylate in toluene or o-xylene at 90 °C, in bulk and in solution, using the novel combination of the catalyst bis-triphenylphosphine iron(II)chloride tetrahydrate (FeCl₂ · 4H₂O(PPh₃)₂) with ethyl 2-bromoisobutyrate ((CH₃)₂CBrCO₂Et)) and α,α-dichloroacetophenone (CHCl₂COPh) as initiators has been investigated. The rate of polymerization initiated by the two initiators exhibited first-order kinetic with respect to the monomer. A linear increase of the number-average molecular weight (M_n) versus monomer conversion was observed for these systems. Among the two initiation systems, ethyl 2-bromoisobutyrate gave the fastest polymerization rate. A system with Fe³⁺ added at the beginning of the polymerization was examined and the lowest polydispersity (M_w/M_n∼1.2) was found when 10% Fe³⁺, relative to Fe²⁺ was added.     

Synthesis of poly(4‐vinylpyridine) by reverse atom transfer radical polymerization

Controlled radical polymerization of 4‐vinylpyridine (4VP) was achieved in a 50 vol % 1‐methyl‐2‐pyrrolidone/water solvent mixture using a 2,2′‐azobis(2,4‐dimethylpentanitrile) initiator and a CuCl₂/2,2′‐bipyridine catalyst–ligand complex, for an initial monomer concentration of [M]₀ = 2.32–3.24 M and a temperature range of 70–80 °C. Radical polymerization control was achieved at catalyst to initiator molar ratios in the range of 1.3:1 to 1.6:1. First‐order kinetics of the rate of polymerization (with respect to the monomer), linear increase of the number–average degree of polymerization with monomer conversion, and a polydispersity index in the range of 1.29–1.35 were indicative of controlled radical polymerization. The highest number–average degree of polymerization of 247 (number–average molecular weight = 26,000 g/mol) was achieved at a temperature of 70 °C, [M]₀ = 3.24 M and a catalyst to initiator molar ratio of 1.6:1. Over the temperature range studied (70–80 °C), the initiator efficiency increased from 50 to 64% whereas the apparent polymerization rate constant increased by about 60%. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5748–5758, 2007     

Synthesis of poly(β‐pinene)‐g‐poly(meth)acrylate by the combination of living cationic polymerization and atom transfer radical polymerization

New graft copolymers of β‐pinene with methyl methacrylate (MMA) or butyl acrylate (BA) were synthesized by the combination of living cationic polymerization and atom transfer radical polymerization (ATRP). β‐Pinene polymers with predetermined molecular weights and narrow molecular weight distributions (MWDs) were prepared by living cationic polymerization with the 1‐phenylethyl chloride/TiCl₄/Ti(OiPr)₄/nBu₄NCl initiating system, and the resultant polymers were brominated quantitatively by N‐bromosuccinamide in the presence of azobisisobutyronitrile, yielding poly(β‐pinene) macroinitiators with different bromine contents (Br/β‐pinene unit molar ratio = 1.0 and 0.5 for macroinitiators a and b , respectively). The macroinitiators, in conjunction with CuBr and 2,2′‐bipyridine, were used to initiate ATRP of BA or MMA. With macroinitiator a or b , the bulk polymerization of BA induced a linear first‐order kinetic plot and gave graft copolymers with controlled molecular weights and MWDs; this indicated the living nature of these polymerizations. The bulk polymerization of MMA initiated with macroinitiator a was completed instantaneously and induced insoluble gel products. However, the controlled polymerization of MMA was achieved with macroinitiator b in toluene and resulted in the desired graft copolymers with controlled molecular weights and MWDs. The structures of the obtained graft copolymers of β‐pinene with (methyl)methacrylate were confirmed by ¹H NMR spectra. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1237–1242, 2003     

Synthesis of poly(vinyl acetate)‐graft‐polystyrene by a combination of cobalt‐mediated radical polymerization and atom transfer radical polymerization

Vinyl acetate and vinyl chloroacetate were copolymerized in the presence of a bis(trifluoro‐2,4‐pentanedionato)cobalt(II) complex and 2,2′‐azobis(4‐methoxy‐2,4‐dimethylvaleronitrile) at 30 °C, forming a cobalt‐capped poly(vinyl acetate‐co‐vinyl chloroacetate). The addition of 2,2,6,6‐tetramethyl‐1‐piperidinyloxy after a certain degree of copolymerization was reached afforded 2,2,6,6‐tetramethyl‐1‐piperidinyloxy‐terminated poly(vinyl acetate‐co‐vinyl chloroacetate) (PVOAc–MI; number‐average molecular weight = 31,000, weight‐average molecular weight/number‐average molecular weight = 1.24). A ¹H NMR study of the resulting PVOAc–MI revealed quantitative terminal 2,2,6,6‐tetramethyl‐1‐piperidinyloxy functionality and the presence of 5.5 mol % vinyl chloroacetate in the copolymer. The atom transfer radical polymerization (ATRP) of styrene (St) was studied with ethyl chloroacetate as a model initiator and five different Cu‐based catalysts. Catalysts with bis(2‐pyridylmethyl)octadecylamine (BPMODA) or tris(2‐pyridylmethyl)amine (TPMA) ligands provided the highest initiation efficiency and best control over the polymerization of St. The grafting‐from ATRP of St from PVOAc–MI catalyzed by copper complexes with BPMODA or TPMA ligands provided poly(vinyl acetate)‐graft‐polystyrene copolymers with relatively high polydispersity (>1.5) because of intermolecular coupling between growing polystyrene (PSt) grafts. After the hydrolysis of the graft copolymers, the cleaved PSt side chains had a monomodal molecular weight distribution with some tailing toward the lower number‐average molecular weight region because of termination. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 447–459, 2007     

Copper catalyzed atom transfer radical copolymerization of glycidyl methacrylate and 2‐ethylhexyl acrylate

This investigation reports the atom transfer radical copolymerization (ATRcP) of glycidyl methacrylate (GMA) and 2‐ethylhexyl acrylate (EHA). Poly(glycidyl methacrylate) (PGMA) has easily transformable pendant oxirane group and poly(2‐ethylhexyl acrylate) (PEHA) has very low T_g. They are the important components of coating and adhesive materials. Copolymerization of GMA and EHA was carried out in bulk and in toluene at 70 °C at different molar feed ratios using CuCl as catalyst in combination with 2,2′‐bypyridine (bpy) as well as N,N,N′,N″,N″‐pentamethyl diethylenetriamine (PMDETA) as ligand. The molecular weight (M_n) and the polydispersity index (PDI) of the polymers were determined by GPC analysis. The molar composition of the copolymers was determined by ¹H NMR analysis. The reactivity ratios of GMA (r₁) and EHA (r₂) were determined using Finemann‐Ross and Kelen‐Tudos linearization methods and those had been compared with the literature values for conventional free radical copolymerization. The thermal properties of the copolymers were studied by DSC and TGA analysis. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6526–6533, 2009