Synthesis and properties of photocurable biodegradable multiblock copolymers based on poly(ε‐caprolactone) and poly(L‐lactide) segments

Photocurable biodegradable multiblock copolymers were synthesized from poly(ε‐caprolactone) (PCL) diol and poly(L ‐lactide) (PLLA) diol with 4,4′‐(adipoyldioxy)dicinnamic acid (CAC) dichloride as a chain extender derived from adipoyl chloride and 4‐hydroxycinnamic acid, and they were characterized with Fourier transform infrared and ¹H NMR spectroscopy, gel permeation chromatography, wide‐angle X‐ray diffraction, differential scanning calorimetry, and tensile tests. The copolymers were irradiated with a 400‐W high‐pressure mercury lamp from 30 min to 3 h to form a network structure in the absence of photoinitiators. The gel concentration increased with time, and a concentration of approximately 90% was obtained in 90–180 min for all the films. The photocuring hardly affected the crystallinity and melting temperature of the PCL segments but reduced the crystallinity of the PLLA segments. The mechanical properties, such as the tensile strength, modulus, and elongation, were significantly affected by the copolymer compositions and gel concentrations. Shape‐memory properties were determined with cyclic thermomechanical experiments. The CAC/PCL and CAC/PCL/PLLA (75/25) films photocured for 30–120 min showed good shape‐memory properties with strain fixity rates and recovery rates of approximately 100%. The formation of the network structure and the crystallization and melting of the PCL segments played very important roles for the typical shape‐memory properties. Finally, the degradation characteristics of these copolymers were investigated in a phosphate buffer solution at 37 °C with proteinase‐k and Pseudomonas cepacia lipase. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2426–2439, 2005     

Novel synthesis of biodegradable star poly(ethylene glycol)‐block‐poly(lactide) copolymers

Biodegradable star‐shaped poly(ethylene glycol)‐block‐poly(lactide) copolymers were synthesized by ring‐opening polymerization of lactide, using star poly(ethylene glycol) as an initiator and potassium hexamethyldisilazide as a catalyst. Polymerizations were carried out in toluene at room temperature. Two series of three‐ and four‐armed PEG‐PLA copolymers were synthesized and characterized by gel permeation chromatography (GPC) as well as ¹H and ¹³C NMR spectroscopy. The polymerization under the used conditions is very fast, yielding copolymers of controlled molecular weight and tailored molecular architecture. The chemical structure of the copolymers investigated by ¹H and ¹³C NMR indicates the formation of block copolymers. The monomodal profile of molecular weight distribution by GPC provided further evidence of controlled and defined star‐shaped copolymers as well as the absence of cyclic oligomeric species. The effects of copolymer composition and lactide stereochemistry on the physical properties were investigated by GPC and differential scanning calorimetry. For the same PLA chain length, the materials obtained in the case of linear copolymers are more viscous, whereas in the case of star copolymer, solid materials are obtained with reduction in their T_g and T_m temperatures. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3966–3974, 2007     

Isothermal crystallization behavior of poly(L‐lactide) in poly(L‐lactide)‐block‐poly(ethylene glycol) diblock copolymers

The crystal unit‐cell structures and the isothermal crystallization kinetics of poly(L ‐lactide) in biodegradable poly(L ‐lactide)‐block‐methoxy poly(ethylene glycol) (PLLA‐b‐MePEG) diblock copolymers have been analyzed by wide‐angle X‐ray diffraction and differential scanning calorimetry. In particular, the effects due to the presence of MePEG that is chemically connected to PLLA as well as the PLLA crystallization temperature T_C are examined. Though we observe no variation of both the PLLA and MePEG crystal unit‐cell structures with the block ratio between PLLA and MePEG and T_C, the isothermal crystallization kinetics of PLLA is greatly influenced by the presence of MePEG that is connected to it. In particular, the equilibrium melting temperature of PLLA, T, significantly decreases in the diblock copolymers. When the T_C is high so that the crystallization is controlled by nucleation, because of the decreasing T and thereafter the nucleation density with decreasing PLLA molecular weight, the crystallinity of PLLA also decreases with a decrease in the PLLA molecular weight. While, for the lower crystallization temperature regime controlled by the growth mechanism, the crystallizability of PLLA in copolymers is greater than that of pure PLLA. This suggests that the activation energy for the PLLA segment diffusing to the crystallization site decreases in the diblocks. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2438–2448, 2006     

Synthesis and characterization of well‐defined cyclodextrin‐centered seven‐arm star poly(ε‐caprolactone)s and amphiphilic star poly(ε‐caprolactone‐b‐ethylene glycol)s

Per‐2,3‐acetyl‐β‐cyclodextrin with seven primary hydroxyl groups was synthesized by selective modification and used as multifunctional initiator for the ring‐opening polymerization of ε‐caprolactone (CL). Well‐defined β‐cyclodextrin‐centered seven‐arm star poly(ε‐caprolactone)s (CDSPCLs) with narrow molecular weight distributions (≤1.15) have been successfully prepared in the presence of Sn(Oct)₂ at 120 °C. The molecular weight of CDSPCLs was characterized by end group ¹H NMR analyses and size‐exclusion chromatography (SEC), which could be well controlled by the molar ratio of the monomer to the initiator. Furthermore, amphiphilic seven‐arm star poly(ε‐caprolactone‐b‐ethylene glycol)s (CDSPCL‐b‐PEGs) were synthesized by the coupling reaction of CDSPCLs with carboxyl‐terminated mPEGs. ¹H NMR and SEC analyses confirmed the expected star block structures. Differential scanning calorimetry analyses suggested that the melting temperature (T_m), the crystallization temperature (T_c), and the crystallinity degree (X_c) of CDSPCLs all increased with the increasing of the molecular weight, and were lower than that of the linear poly(ε‐caprolactone). As for CDSPCL‐b‐PEGs, the T_c and T_m of the PCL blocks were significantly influenced by the PEG segments in the copolymers. Moreover, these amphiphilic star block copolymers could self‐assemble into spherical micelles with the particle size ranging from 10 to 40 nm. Their micellization behaviors were characterized by dynamic light scattering and transmission electron microscopy. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6455–6465, 2008     

Synthesis and characterization of a series of biodegradable and biocompatible PEG‐supported poly(lactic‐ran‐glycolic acid) amphiphilic barbell‐like copolymers

A series of multihydroxyl (2, 4, and 8) terminated poly(ethylene glycol)s and their biodegradable, biocompatible, and branched barbell‐like (PLGA)_n‐b‐PEG‐b‐(PLGA)_n (n = 1, 2, 4) copolymers have been synthesized. The lengths of the PLGA arms were varied by controlling the molar ratio of monomers to hydroxyl groups of PEG ([LA+GA]₀/[? OH]₀ = 23, 45, 90). Chemical structures of synthesized barbell‐like copolymers were confirmed by both ¹H and ¹³C‐NMR spectroscopies. Molecular weights were determined by ¹H‐NMR end‐group analysis and gel permeation chromatography. The result of hydrolytic degradation indicated that the rate of degradation increased with the increase of arm numbers or with the decrease of arm lengths. The thermal properties were evaluated by using differential scanning calorimetry and a thermogravimetric analysis. The results indicated that the thermal properties of barbell‐like copolymers depended on the structural variations. The morphology of (PLGA)_n‐PEG‐(PLGA)_n copolymers self‐assembly films were investigated by atomic force microscope, the results indicated that the microphase separation existed in (PLGA)_n‐PEG‐(PLGA)_n copolymers. Because of the favorable biodegradability and biocompatibility of the PLGA and PEG, these results may therefore create new possibilities for these novel structural amphiphilic barbell‐like copolymers as potential biomaterials. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3802–3812, 2008     

Synthesis and characterization of poly(L‐lactic acid)–poly(ε‐caprolactone) multiblock copolymers by melt polycondensation

An Erratum has been published for this article in J. Polym. Sci. Part A: Polym. Chem. (2004) 42(22) 5845 New multiblock copolymers derived from poly(L‐lactic acid) (PLLA) and poly(ε‐caprolactone) (PCL) were prepared with the coupling reaction between PLLA and PCL oligomers with ? NCO terminals. Fourier transform infrared (FTIR), ¹³C NMR, and differential scanning calorimetry (DSC) were used to characterize the copolymers and the results showed that PLLA and PCL were coupled by the reaction between ? NCO groups at the end of the PCL and ? OH (or ? COOH) groups at the end of the PLLA. DSC data indicated that the different compositions of PLLA and PCL had an influence on the thermal and crystallization properties including the glass‐transition temperature (T_g), melting temperature (T_M), crystallizing temperature (T_c), melting enthalpy (ΔH_m), crystallizing enthalpy (ΔH_c), and crystallinity. Gel permeation chromatography (GPC) was employed to study the effect of the composition of PLLA and PCL and reaction time on the molecular weight and the molecular weight distribution of the copolymers. The weight‐average molecular weight of PLLA–PCL multiblock copolymers was up to 180,000 at a composition of 60% PLLA and 40% PCL, whereas that of the homopolymer of PLLA was only 14,000. A polarized optical microscope was used to observe the crystalline morphology of copolymers; the results showed that all polymers exhibited a spherulitic morphology. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5045–5053, 2004     

Tuning the LCST of poly(2‐cyclopropyl‐2‐oxazoline) via gradient copolymerization with 2‐ethyl‐2‐oxazoline

Poly(2‐propyl‐oxazoline)s can be prepared by living cationic ring‐opening polymerization of 2‐oxazolines and represent an emerging class of biocompatible polymers exhibiting a lower critical solution temperature in aqueous solution close to body temperature. However, their usability is limited by the irreversibility of the transition due to isothermal crystallization in case of poly(2‐isopropyl‐2‐oxazoline) and the rather low glass transition temperatures (T_g < 45 °C) of poly(2‐n‐propyl‐2‐oxazoline)‐based polymers. The copolymerization of 2‐cyclopropyl‐2‐oxazoline and 2‐ethyl‐2‐oxazoline presented herein yields gradient copolymers whose cloud point temperatures can be accurately tuned over a broad temperature range by simple variation of the composition. Surprisingly, all copolymers reveal lower T_gs than the corresponding homopolymers ascribed to suppression of interchain interactions. However, it is noteworthy that the copolymers still have T_gs > 45 °C, enabling convenient storage in the fridge for future biomedical formulations. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3118–3122     

Novel synthesis of biodegradable amphiphilic linear and star block copolymers based on poly(ε‐caprolactone) and poly(ethylene glycol)

Biodegradable, amphiphilic, diblock poly(ε‐caprolactone)‐block‐poly(ethylene glycol) (PCL‐b‐PEG), triblock poly(ε‐caprolactone)‐block‐poly(ethylene glycol)‐block‐poly(ε‐caprolactone) (PCL‐b‐PEG‐b‐PCL), and star shaped copolymers were synthesized by ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) methyl ether or poly(ethylene glycol) or star poly(ethylene glycol) and potassium hexamethyldisilazide as a catalyst. Polymerizations were carried out in toluene at room temperature to yield monomodal polymers of controlled molecular weight. The chemical structure of the copolymers was investigated by ¹H and ¹³C NMR. The formation of block copolymers was confirmed by ¹³C NMR and DSC investigations. The effects of copolymer composition and molecular structure on the physical properties were investigated by GPC and DSC. For the same PCL chain length, the materials obtained in the case of linear copolymers are viscous whereas in the case of star copolymer solid materials are obtained with low T_g and T_m temperatures. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3975–3985, 2007     

Synthesis of a novel block copolymer poly(ethylene oxide)‐block‐poly(4‐vinylpyridine) by combination of anionic ring‐opening and controllable free‐radical polymerization

The block copolymer poly(ethylene oxide)‐b‐poly(4‐vinylpyridine) was synthesized by a combination of living anionic ring‐opening polymerization and a controllable radical mechanism. The poly(ethylene oxide) prepolymer with the 2,2,6,6‐tetramethylpiperidinyl‐1‐oxy end group (PEO_T) was first obtained by anionic ring‐opening polymerization of ethylene oxide with sodium 4‐oxy‐2,2,6,6‐tetramethylpiperidinyl‐1‐oxy as the initiator in a homogeneous process. In the polymerization UV and electron spin resonance spectroscopy determined the 2,2,6,6‐tetramethylpiperidinyl‐1‐oxy moiety was left intact. The copolymers were then obtained by radical polymerization of 4‐vinylpyridine in the presence of PEO_T. The polymerization showed a controllable radical mechanism. The desired block copolymers were characterized by gel permeation chromatography, Fourier transform infrared, and NMR spectroscopy in detail. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4404–4409, 2002     

Thermoplastic elastomers based on poly(l‐Lysine)‐Poly(ε‐Caprolactone) multi‐block copolymers

Novel thermoplastic elastomers based on multi‐block copolymers of poly(l ‐lysine) (PLL), poly(N‐ε‐carbobenzyloxyl‐l ‐lysine) (PZLL), poly(ε‐caprolactone) (PCL), and poly(ethylene glycol) (PEG) were synthesized by combination of ring‐opening polymerization (ROP) and chain extension via l ‐lysine diisocyanate (LDI). SEC and ¹H NMR were used to characterize the multi‐block copolymers, with number‐average molecular weights between 38,900 and 73,400 g/mol. Multi‐block copolymers were proved to be good thermoplastic elastomers with Young's modulus between 5 and 60 MPa and tensile strain up to 1300%. The PLL‐containing multi‐block copolymers were electrospun into non‐woven mats that exhibited high surface hydrophilicity and wettability. The polypeptide–polyester materials were biocompatible, bio‐based and environment‐friendly for promising wide applications. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3012–3018     

Synthesis of biodegradable thermoplastic elastomers from ε‐caprolactone and lactide

This article reports the synthesis and the properties of novel thermoplastic elastomers of A‐B‐A type triblock copolymer structure, where the hard segment A is poly(l ‐lactide) (PLLA) and the soft segment B is poly(ε‐caprolactone‐stat‐d ,l ‐lactide) (P(CL‐stat‐DLLA)). The P(CL‐stat‐DLLA) block with DLLA content of 30 mol % was applied because of its amorphous nature and low glass transition temperature (T_g = approximately ?40 °C). Successive polymerization of l ‐lactide afforded PLLA‐block‐P(CL‐stat‐DLLA)‐block‐PLLAs, which exhibited melting temperature (T_m = approximately 150 °C) for the crystalline PLLA segments and still low T_g (approximately ?30 °C) of the soft segments. The triblock copolymers showed very high elongation at break up to approximately 2800% and elastic properties. The corresponding d ‐triblock copolymers, PDLA‐block‐P(CL‐stat‐DLLA)‐block‐PDLAs (PDLA = poly(d ‐lactide)) were also prepared with the same procedure using d ‐lactide in place of l ‐lactide. When the PLLA‐block‐P(CL‐stat‐DLLA)‐block‐PLLA was blended with PDLA‐block‐P(CL‐stat‐DLLA)‐block‐PDLA, stereocomplex crystals were formed to enhance their T_m as well as tensile properties. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 489–495     

Controlled synthesis and microstructure tuning of PEG‐containing side‐chain discotic liquid crystalline block copolymers via RAFT polymerization

Liquid crystalline block copolymers (LCBCPs) are fascinating for their combining molecular level liquid crystalline orders and microphase separated multidomain morphologies. Here in this article, a series of PEG‐containing side‐chain discotic LCBCPs of PEG‐b‐P_m‐n with variant spacer length m = 6, 10 and degree of polymerization (DP) of discotic LC block from n = 10 to 45, have been well‐synthesized via reversible addition‐fragmentation chain‐transfer (RAFT) polymerization. The RAFT process mediated by macromolecular chain transfer agent (macroCTA) shows remarkable monomer concentration dependence. The influence of the introduced PEG block on the nano‐scale microphase‐segregation and mesophase organization is closely related to the side‐chain triphenylene (TP) discogens stacking mode dependent on the spacer length. Wherein, the PEG‐b‐P₆‐n series with a six‐methylene spacer exhibit consistent microphase separation with slightly disturbed yet ordered columnar structures. While for PEG‐b‐P₁₀‐n series with a longer ten‐methylene spacer, the columnar organization in the copolymers is even improved in contrast with the low order of randomly TP stacking in their corresponding homopolymers. This work offers a viable and inspiring pathway for controlled synthesis of block copolymers with bulky side groups, as well as enhances in‐depth understanding of the hierarchical superstructure organization in discotic units involved complex block copolymers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2544–2553     

Segmented block copolymers based on poly(propylene oxide) and monodisperse polyamide‐6,T segments

Polyether(ester amide)s with poly(propylene oxide) (PPO) and monodisperse poly(hexamethylene terephthalamide) segments were synthesized, and their structure–property relations were investigated. The length of the amide segments was varied from diamide to tetraamide to hexaamide segments, and therefore the number hydrogen bonds per amide segment increased from two to four to six. PPO was end‐capped with 20 wt % ethylene oxide and had number‐average molecular weights of 1000, 2300, and 4000 g/mol (including ethylene oxide tips). The morphology of the poly‐ether(ester amide)s was studied with transmission electron microscopy and atomic force microscopy, the thermal properties were studied with differential scanning calorimetry and dynamic mechanical thermal analysis, and the tensile properties were studied with dumbbell samples. The elastic behavior of the block copolymers was investigated with tensile and compression tests. These segmented copolymers had two sharp transitions: a glass‐transition temperature (T_g) of the PEO–PPO–PEO phase [where PEO is poly(ethylene oxide)] and a melting temperature (T_m) of the amide segments. The amide segments crystallized in nanoribbons with a high aspect ratio 1000. T_m increased with the amide segment length and with decreasing PEO–PPO–PEO content (solvent effect). The modulus increased strongly with the amide content. This modulus increase could be described by the Halpin–Tsai fiber composite model. Increasing the amide segment length surprisingly also improved the elasticity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4769–4781, 2006     

Thermal behavior and crystallization kinetics of random poly(ethylene‐Co‐2,2‐Bis[4‐(ethylenoxy)‐1,4‐phenylene]propane terephthalate) copolyesters

The thermal behavior of poly(ethylene‐co‐2,2‐bis[4‐(ethylenoxy)‐1,4‐phenylene]propane terephthalate) (PET/BHEEBT) copolymers was investigated by thermogravimetric analysis and differential scanning calorimetry. A good thermal stability was found for all the samples. The thermal analysis carried out using DSC technique showed that the T_m of the copolymers decreased with increasing BHEEBT unit content, differently from T_g, which on the contrary increased. Wide‐angle X‐ray diffraction measurements permitted identifying the kind of crystalline structure of PET in all the semicrystalline samples. The multiple endotherms similar to PET were also evidenced in the PET/BHEEBT samples, due to melting and recrystallization processes. By applying the Hoffman–Weeks' method, the T_m° of PET and its copolymers was derived. The isothermal crystallization kinetics was analyzed according to Avrami's treatment and values of the exponent n close to 3 were obtained, independently of T_c and composition. Moreover, the introduction of BHEEBT units was found to decrease PET crystallization rate. Lastly, the presence of a crystal‐amorphous interphase was evidenced. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1441–1454, 2005     

Synthesis and self‐assembly of amphiphilic brush‐dendritic‐linear poly[poly(ethylene glycol) methyl ether methacrylate]‐b‐ polyamidoamine‐b‐poly(ε‐caprolactone) copolymers

A series of novel amphiphilic brush‐dendritic‐linear poly[poly(ethylene glycol) methyl ether methacrylate]‐b‐polyamidoamine‐b‐poly(ε‐caprolactone) copolymers (PPEGMEMA‐b‐D_m‐b‐PCL) (m = 1, 2, and 3: the generation number of dendron) were synthesized by the combination techniques of click chemistry, atom transfer radical polymerization (ATRP), and ring‐opening polymerization (ROP). The brush‐dendritic copolymers bearing hydrophilic brush PPEGMEMA and hydrophobic dendron polyamidoamine protected by the tert‐butoxycarbonyl (Boc) groups [D_m‐(Boc) (m = 1, 2, and 3)] were for the first time prepared by ATRP of poly(ethylene glycol) methyl ether methacrylate monomer (PEGMEMA) initiated with the dendron initiator, which was prepared from 2′‐azidoethyl‐2‐bromoisobutyrate (AEBIB) and D_m‐(Boc) terminated with a clickable alkyne by click chemistry. Then, the brush‐dendritic copolymers with primary amine groups (PPEGMEMA‐b‐D_m) were obtained from the removal of the protected Boc groups of the brush‐dendritic copolymers in the presence of trifluoroacetic acid. The brush‐dendritic‐linear PPEGMEMA‐b‐D_m‐b‐PCL copolymers were synthesized from ROP of ε‐caprolactone monomer using PPEGMEMA‐b‐D_m as the macroinitiators and stannous octoate as catalyst in toluene at 130 °C. To the best of our knowledge, this is the first report that integrates hydrophilic brush polymer PPEGMEMA with hydrophobic polyamidoamine (PAMAM) dendron and PCL to form amphiphilic brush‐dendritic‐linear copolymers. The amphiphilic brush‐dendritic‐linear copolymers can self‐assemble into spherical micellar structures in aqueous solution. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of novel poly(thioether‐naphthalimide)s that utilize hydrazine as the diamine

A series of bis(4‐thio‐1,8‐naphthalic anhydride)s and the corresponding bis(N‐amino naphthalimide) derivatives were synthesized from readily available compounds in high yield. A series of novel poly(thioether‐naphthalimide)s, which utilized hydrazine as the diamine, were synthesized by a one‐step polymerization reaction in m‐cresol. Poly(thioether‐naphthalimide)s with inherent viscosities of 0.57–1.73 dL/g were obtained. The polymers were soluble in CHCl₃ and were determined to have high molecular weights by means of gel permeation chromatographic analysis. They were soluble in m‐cresol and could be cast into tough films from m‐cresol solution. The glass‐transition temperature (T_g) values of the polyimides ranged from 320 to 353 °C. Polyimides from the bisphenol dianhydride, derived from 9,9‐bis(4‐hydroxyphenyl)fluorene, did not show a clear transition in the DSC analysis. Degradation temperatures for 5% weight loss all occurred above 430 °C in nitrogen. The series of monomers were successfully copolymerized with each other. Monomers 6a and 7a , containing the bisphenol A moiety, could also be copolymerized with perylenetetracarboxylic dianhydride. These copolymers had high T_g's and were thermally stable. The UV–vis absorption properties of the polymers were also examined. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1040–1050, 2001     

Thermosensitive behavior of poly(ethylene glycol)/poly(2‐(N,N‐dimethylamino)ethyl methacrylate) double hydrophilic block copolymers

The poly(ethylene glycol)/poly(2‐(N,N‐dimethylamino)ethyl methacrylate) (PEG/PDMAEMA) double hydrophilic block copolymers were synthesized by atom transfer radical polymerization using mPEG‐Br or Br‐PEG‐Br as macroinitiators. The narrow molecular weight distribution of PEG/PDMAEMA block copolymers was identified by gel permeation chromatography results. The thermosensitivity of PEG/PDMAEMA block copolymers in aqueous solution was revealed to depend significantly on pH, ionic strength, chain structure, and concentration of the block copolymers. By optimizing these factors, the cloud point temperature of PEG/PDMAEMA block copolymers can be limited within body temperature range (30–37 °C), which suggests that PEG/PDMAEMA block copolymers could be a good candidate for drug delivery systems. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 503–508, 2010     

Functional syndiotactic poly(β‐hydroxyalkanoate)s via stereoselective ring‐opening copolymerization of rac‐β‐butyrolactone and rac‐allyl‐β‐butyrolactone

The copolymerization of racemic β‐butyrolactone (rac‐BL^Me) with racemic “allyl‐β‐butyrolactone” (rac‐BL^allyl) in toluene, catalyzed by the discrete amino‐alkoxy‐bis(phenolate) yttrium‐amido complex 1 , gave new poly(β‐hydroxyalkanoate)s with unsaturated side chains. The poly(BL^Me‐co‐BL^allyl) copolymers produced have a highly syndiotactic backbone structure (P_r = 0.80–0.84) with a random enchainment of monomer units, as evidenced by ¹³C NMR, and high molecular weight (M_n up to 58,000 g mol^?1) with a narrow polydispersity (M_w/M_n = 1.07–1.37), as determined by GPC. The comonomer incorporation (5–50 mol % rac‐BL^allyl) was a linear function of the feed ratio. The pendant vinyl bond of the side‐chains in those poly(BL^Me‐co‐BL^allyl) copolymers allowed the effective introduction of hydroxy or epoxy groups via dihydroxylation, hydroboration‐oxidation or epoxidation reactions. NMR studies indicated that all of these transformations proceed in an essentially quantitative conversion and do not affect the macromolecular architecture. Some thermal properties (T_m, ΔH_m, T_g) of the prepared polymers have been also evaluated. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3177–3189, 2009     

Synthesis,micellar structures,and multifunctional sensory properties of poly(3‐hexylthiophene)‐block‐poly(2‐(dimethylamino)ethyl methacrylate) rod‐coil diblock copolymers

We report the synthesis, micellar structures, and multifunctional sensory properties of new conjugated rod‐coil block copolymers, poly(3‐hexylthiophene)‐block‐poly(2‐(di methylamino)ethylmethacrylate)(P3HT‐b‐PDMAEMA). The new copolymers, synthesized by atom transfer radical polymerization of P3HT macroinitiator, consisted PDMAEMA coil lengths of 43, 65, and 124 repeating units. All the P3HT‐b‐PDMAEMA copolymers exhibit a similar low critical solution temperature in water around 33 °C. The micellar structures of the synthesized polymers were characterized by AFM, TEM, and dynamic light scattering, by varying temperature, pH, and water/THF composition. The micelles of P3HT₂₀‐b‐PDMAEMA₄₃ in water had a reversible size change from 75 ± 5 nm to 132 ± 5 nm on heating from 25 to 55 °C and reduced to the original size during cooling. In addition, the micellar size also showed a significant pH dependence, changing from 67 ± 8 nm (pH = 12) to 222 ± 6 nm (pH = 4), depending on the protonation of the PDMAEMA blocks and their electrostatic repulsion. The micellar structure of three P3HT‐b‐PDMAEMA copolymers changed from spheres, to vesicles, and finally to larger sphere micelles as the solvent composition varied from 0 to 100 wt % water in the mixed solvent. The different micellar structures of P3HT₂₀‐b‐PDMAEMA₄₃ solution led to a red‐shift on the absorption or photoluminescence spectra and exhibited the emission colors of yellow, orange, red, and dark red with increasing the water content. This study suggested that new copolymers had potential applications as multifunctional sensory materials toward temperature, pH, and solvent. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010