Use of miniaturised isotachophoresis on a planar polymer chip to analyse transition metal ions in solutions from metal processing plants

An electrolyte system, using malic acid as a complexing agent, has been developed to allow the determination of transition metal cations using miniaturised isotachophoresis. The method allowed the simultaneous determination of Mn2+, Cr3+, Fe2+, Co2+, Zn2+ and Ni2+ to be made without interference from other common ions. Limits of detection were calculated to be in the range 0.5-1.0mg l(-1) for Mn2+, Cr3+ Co2+ and Zn2+ and 2.0 mg l(-1) for Fe2+ and 4.7 mg l(-1) for Ni2+. The successful analysis of five industrial samples, containing a range of these metal ions, obtained from metal processing plants were achieved in under 13 min. The separations were performed on a poly(methyl methacrylate) chip with integrated platinum wire conductivity detection electrodes.     

低压离子分离-化学发光在线检测过渡金属离子

 研究了低压离子 (LPIC)分离 柱后鲁米诺化学发光 (CL)检测方法 ,并分离测定了Cu2 + ,Co2 + ,Cr3 + ,Fe2 + ,Mn2 + 等 5种过渡金属离子。以草酸 柠檬酸混合溶液作为洗脱液 ,Luminol H2 O2 Mn + 作为化学发光检测体系 ,对过渡金属离子进行在线检测。测定的线性范围分别为 (mg·L-1) :Co2 + ,0 0 0 1～ 0 .1;Cu2 + ,0 1～ 6 ;Mn2 + ,0 0 6～ 4 ;Fe2 + ,0 0 3～ 5 ;Cr3 + ,0 0 2 5～ 1。检测限分别为 (μg·L-1) :Co2 + ,0 85 ;Cu2 + ,85 ;Mn2 + ,4 2 ;Fe2 + ,2 1;Cr3 + ,2 0。     

Speciation of V, Cr and Fe by capillary electrophoresis-bandpass reaction cell inductively coupled plasma mass spectrometry

Capillary electrophoresis-dynamic reaction cell inductively coupled plasma mass spectrometry (CE-DRC-ICP-MS) for the speciation of iron(III/II), vanadium(V/IV) and chromium(VI/III) is described. Two different CE migration modes were employed for separating the six metal ions using pre-capillary complexation. One is counter-electroosmotic mode in which iron(III/II) and vanadium(V/IV) ions were well separated using a 60 cm x 75 microm i.d. fused silica capillary. The voltage was set at +22 kV and a 15 mmol l(-1) tris(hydroxymethyl)aminomethane (Tris) buffer (pH 8.75) containing 0.5 mmol l(-1) ethylenediaminetetraacetic acid (EDTA) and 0.5 mmol l(-1) ortho-phenanthroline (phen) was used as the electrophoretic buffer. The other is co-electroosmotic mode in which chromium(VI/III) ions were well separated while the applied voltage was set at -22 kV and a 10 mmol l(-1) ammonium citrate buffer (pH 7.7) containing 0.5 mmol l(-1) diethylenetriaminepentaacetic acid (DTPA) and 0.01% polybrene was used as the electrophoretic buffer. The mass spectra were measured at m/z 51, 52 and 56 for V. Cr and Fe, respectively. The interfering polyatomic ions of 35Cl16O+, 40Ar12C+ and 40Ar16O+ on 51V+, 52Cr+ and 56Fe+ determination were reduced in intensity significantly by using NH3 as the reaction cell gas in the DRC. The detection limits were in the range of 0.1-0.5, 0.4-1.3 and 1.2-1.7 ng ml(-1) for V, Cr and Fe, respectively. Applications of the method for the speciation of V, Cr and Fe in wastewater were demonstrated. The recoveries were in the range of 92-120% for various species.     

A potentiometric rhodamine-B based membrane sensor for the selective determination of chromium ions in wastewater.

The construction and performance characteristics of a novel chromate ion-selective membrane sensor are described and used for determining chromium(III) and chromium(VI) ions. The sensor is based on the use of a rhodamine-B chromate ion-associate complex as an electroactive material in a poly(vinyl chloride) membrane plasticized with o-nitrophenyloctyl ether as a solvent mediator. In a phosphate buffer solution of pH 6 - 7, the sensor displays a stable, reproducible and linear potential response over the concentration range of 1 x 10(-1) - 5 x 10(-6) mol l(-1) with an anionic Nernstian slope of 30.8 +/- 0.5 mV decade(-1) and a detection limit of 1 x 10(-6) mol l(-1) Cr(VI). High selectivity for Cr(VI) is offered over many common anions (e.g., I-, Br-, Cl-, IO4-, CN-, acetate, oxalate, citrate, sulfate, phosphate, thiosulfate, selenite, nitrate) and cations (e.g., Ag+, Ca2+, Sr2+, Co2+, Ni2+, Cu2+, Mn2+, Fe2+, Zn2+, Cd2+, Al3+, Cr3+). The sensor is used for determining Cr(VI) and/or Cr(III) ions in separate or mixed solutions after the oxidation of Cr(III) into Cr(VI) with H2O2. As low as 0.2 microg ml(-1) of chromium is determined with a precision of +/-1.2%. The chromium contents of some wastewater samples were accurately assessed, and the results agreed fairly well with data obtained by atomic absorption spectrometry.     

Synthesis of 5-dialkyl(aryl)aminomethyl-8-hydroxyquinoline dansylates as selective fluorescent sensors for Fe3+

A series of 5-dialkyl(aryl)aminomethyl-8-hydroxyquinoline dansylates were synthesized and their fluoroionophoric properties toward representative alkali ions, alkaline earth ions and transition metal ions were investigated. Among the selected ions, Fe3+ caused considerable quenching of the fluorescence, while Cr3+ caused quenching to some extent. The absence of any significant fluorescence quenching effects of the other ions examined, especially Fe2+, renders these compounds highly useful Fe3+-selective fluorescent sensors.     

吡咯并[2,1,5-cd]中氮茚酰腙衍生物的合成及Cu2+荧光探针行为

设计合成了吡咯并[2,1,5-cd]中氮茚酰腙衍生物6. 测试了其紫外光谱和荧光光谱, 研究了其对铜离子的选择性识别作用. 结果表明, 化合物6作为铜离子荧光探针, 受常见离子干扰较小, 对于铜离子有着较高的选择性和较低的检出限.     

Cooperative near-IR to visible photon upconversion in Yb3+-doped MnCl2 and MnBr2: comparison with a series of Yb3+-doped Mn2+ halides

Yb3+-doped MnCl2 and MnBr2 crystals exhibit strong red upconversion luminescence under near-infrared excitation around 10 000 cm(-1) at temperatures below 100 K. The broad red luminescence band is centred around 15 200 cm(-1) for both compounds and identified as the Mn2+ 4T1g-->6A1g transition. Excitation with 10 ns pulses indicates that the upconversion process consists of a sequence of ground-state and excited-state absorption steps. The experimental VIS/NIR photon ratio at 12 K for an excitation power of 191 mW focused on the sample with a 53 mm lens is 4.1% for MnCl2:Yb3+ and 1.2% for MnBr2:Yb3+. An upconversion mechanism based on exchange coupled Yb3+-Mn2+ ions is proposed. Similar upconversion properties have been reported for RbMnCl3:Yb3+, CsMnCl3:Yb3+, CsMnBr3:Yb3+, RbMnBr3:Yb3+, Rb2MnCl4:Yb3+. The efficiency of the upconversion process in these compounds is strongly dependent on the connectivity between the Yb3+ and Mn2+ ions. The VIS/NIR photon ratio decreases by three orders of magnitude along the series of corner-sharing Yb3+-Cl--Mn2+, edge-sharing Yb3+-(Cl-)2-Mn2+ to face-sharing Yb3+-(Br-)3-Mn2+ bridging geometry. This trend is discussed in terms of the dependence of the relevant super-exchange pathways on the Yb(3+)-Mn2+ bridging geometry.     

Speciation of chromium by in-capillary reaction and capillary electrophoresis with chemiluminescence detection

A sensitive method for the simultaneous determination of chromium(III) (Cr3+) and chromium(VI) (CrO4(2-)) using in-capillary reaction, capillary electrophoresis (CE) separation and chemiluminescence (CL) detection was developed. The chemiluminescence reaction was based on luminol oxidation by hydrogen peroxide in basic aqueous solution catalyzed by Cr3+ ion followed by capillary electrophoresis separation. Based on in-capillary reduction, chromium(VI) can be reduced by acidic sodium hydrogensulfite to form chromium(III) while the sample is running through the capillary. Before the electrophoresis procedure, the sample (Cr3+ and CrO4(2-)), buffer and acidic sodium hydrogensulfite solution segments were injected in that order into the capillary, followed by application of an appropriate running voltage between both ends. As both chromium species have opposite charges, Cr3+ ions migrate to the cathode, while CrO4(2-) ions, moving in the opposite direction toward the anode, react with acidic sodium hydrogensulfite which results in the formation of Cr3+ ions. Because of the migration time difference of both Cr3+ ions, Cr(III) and Cr(VI) could be separated. The running buffer was composed of 0.02 mol l(-1) acetate buffer (pH 4.7) with 1 x 10(-3) mol l(-1) EDTA. Parameters affecting CE-CL separation and detection, such as reductant (sodium hydrogensulfite) concentration, mixing mode of the analytes with CL reagent, CL reaction reagent pH and concentration, were optimized. The limits of detection (LODs) of Cr(III) and Cr(VI) were 6 x 10(-13) and 8 x 10(-12) mol l(-1) (S/N=3), respectively. The mass LODs for Cr(III) and Cr(VI) were 1.2 x 10(-20) mol (12 zmol) and 3.8 x 10(-19) mol (380 zmol), respectively.     

均三嗪衍生物应用于Fe3+和Cu2+的选择性识别研究

合成了2,4-二甲基-6-(4’-N,N-二甲氨基苯乙烯基)-1,3,5-均三嗪(1)和2-苯乙烯基-4,6-二甲基-1,3,5-均三嗪(2)两种化合物,并对其进行了1H NMR,MS,元素分析等表征.采用吸收光谱法研究了金属离子与化合物间的相互作用,结果显示:化合物1对Fe3+和Cu2+表现出高选择性光谱响应,其最大吸收波长由393 nm分别红移至525 nm和513 nm,溶液颜色由黄色变为粉红色.化合物1与Fe3+结合形成1∶1型配合物,其结合常数为1.8×104L mol-1;与Cu2+结合形成2∶1型配合物,其结合常数为2.6×1010L mol-1.化合物2仅对Fe3+呈现显著的光谱变化,其最大吸收波长由304nm红移至357 nm,而Cu2+的加入未引起光谱明显变化,2与Fe3+亦形成1∶1型配合物,结合常数为1.0×105L mol-1.结果表明Fe3+可能与化合物1和2中三嗪N配位,而Cu2+与化合物1中甲氨基中的N配位.同时考察了其它金属离子如Li+,K+,Mg2+,Ca2+,Co3+,Ni2+,Ag+,Cd2+,Hg2+和Zn2+等离子对化合物1和2吸收光谱的影响,结果显示两者光谱均无明显变化,据此提出了高选择性Fe3+,Cu2+的识别体系.     

Fe3O4 and gamma-Fe2O3 nanoparticles for the adsorption of Co2+ from aqueous solution

The adsorption of Co2+ ions from nitrate solutions using iron oxide nanoparticles of magnetite (Fe3O4) and maghemite (gamma-Fe2O3) has been studied. The adsorption of Co2+ ions on the surface of the particles was investigated under different conditions of oxide content, contact time, solution pH, and initial Co2+ ion concentration. It has been found that the equilibrium can be attained in less than 5 min. The maximum loading capacity of Fe3O4 and gamma-Fe2O3 nanoparticles is 5.8 x 10(-5) and 3.7 x 10(-5) mol m(-2), respectively, which are much higher than the previously studied, iron oxides and conventional ion exchange resins. Co2+ ions were also recovered by dilute nitric acid from the loaded gamma-Fe2O3 and Fe3O4 with an efficiency of 86 and 30%, respectively. That has been explained by the different mechanisms by including both the surface and structural loadings of Co2+ ions. The surface adsorption of Co2+ on Fe3O4 and gamma-Fe2O3 nanoparticles has been found to have the same mechanism of ion exchange reaction between Co2+ in the solution and proton bonded on the particle surface. The conditional equilibrium constants of surface adsorption of Co2+ on Fe3O4 and gamma-Fe2O3 nanoparticles have been determined to be log K=-3.3+/-0.3 and -3.1+/-0.2, respectively. The structural loading of Co2+ ions into Fe3O4 lattice has been found to be the ion exchange reaction between Co2+ and Fe2+ while that into gamma-Fe2O3 lattice to fill its vacancy. The effect of temperature on the adsorption of Co2+ was also investigated, and the value of enthalpy change was determined to be 19 kJ mol(-1).     

Energy transfer characteristics of the hydrogen peroxide induced Ce3+-Ce4+ mixture

Luminescence of Ce3+ in the hydrogen peroxide induced sulfuric acid solutions was observed to be quenched by Ce4+ ions in the solution by energy transfer due to electric dipole interaction between Ce3+ and Ce4+. A systematic investigation of the energy transfer characteristics of Ce3+-Ce4+ mixture has been made by measuring the absorption, luminescence and excitation spectra at room temperature. The effect of the concentration of Ce3+ on the energy transfer process has been also studied and the critical transfer distance (Ro) has been calculated considering F?rster type interaction between the ions and found to be 8.7 A for the mixture of 1 x 10(-4) mol 1(-1) Ce3+ and 3 x 10(-4) mol l(-1) Ce4+.     

含席夫碱基二茂铁-蒽二元化合物的合成及其阳离子多信号识别

合成了一种含席夫碱基团的二茂铁-蒽二元化合物1, 并研究了其金属离子识别时紫外-可见光谱, 荧光光谱及电化学变化. 在各种金属离子中, 1 对Cr³⁺, Cu²⁺及Hg²⁺显示出多种信号响应识别: 1 位于407 nm 的Fe(II)→Cp 的荷移光谱发生约100 nm 红移, 且颜色由黄色变为红色, 同时使其Fe(III)/Fe(II)电位向阳极移动. 同时, 荧光光谱表明1 仅对Cr³⁺显示荧光增强效应.     

Polyacrylic acid-modified alumina for solid-phase extraction and preconcentration of trace iron and chromium from plant samples

A new method is presented for simultaneous preconcentration of trace Fe(III) and Cr(III) by using polyacrylic acid-alumina as a sorbent. The separation/preconcentration conditions of analytes were investigated, including effect of pH, flow rate, elution conditions, sample volume, and interfering ions. At pH 4, the maximum sorption capacities of Fe3+ and Cr3+ were 8.0 and 13.0 mg/g, respectively, by the column method. The linearity was maintained in the concentration range of 0.175-6.0 x 10(3) ng/mL for iron and 0.175-8.0 x 10(3) ng/mL for chromium in the original solution. The RSD values under optimum conditions were +/- 1.73 and +/- 1.28% for 2.0 microg/mL Fe and Cr, respectively. The preconcentration factor was 400 for both of the elements, and detection limits were 0.025 and 0.023 ng/mL for Fe and Cr in the original solutions. The proposed method was successfully applied to the determination of trace amounts of Fe and Cr in plant samples.     

两种磺酰胺类化合物的合成及其对Fe3+的氧化-还原荧光“开-关”性质

合成了两种磺酰胺类化合物, 并研究了其荧光性能. 通过它们对金属阳离子的选择性识别实验, 发现其在乙醇水溶液中均对Fe3+有专一性的识别作用, 并在NH2OH·HCl和H2O2的存在下, 两种化合物对Fe3+都具有氧化-还原荧光“开-关”作用.     

巯基树脂对金属离子的吸附性能(Ⅱ)

研究了自合成的巯基树脂对重金属离子Ag 、Hg2 、Cr3 的吸附容量、吸附动力学、等温吸附过程等静态吸附性能,影响吸附的因素和吸附机理.结果表明,该树脂对上述3种离子吸附能力强,吸附量分别达6.56mmol/g、3.25mmol/g、2.10mmol/g.树脂对各重金属离子等温吸附在实验浓度范围内符合Langmuir或Freundlich方程.吸附机理研究表明,巯基与金属离子发生了离子交换和配位反应,化学吸附起支配作用;另外树脂对Ag 、Hg2 吸附过程中存在一定的氧化还原现象.     

Purification and properties of bilirubin oxidase fromMyrothecium verrucaria

Bilirubin oxidase was purified from a culture filtrate of Myrothecium verrucaria Mv 2, 1089 by DEAE-cellulose and Sephadex G-100 column chromatographies. The purified enzyme had a specific activity of 30 U/mg protein and showed a single band on polyacrylamide gel electrophoresis. Some of the general properties of this bilirubin oxidase were as follows: the optimum pH for the enzyme reaction was 7.5 and the optimum temperature was 50 degrees C. The enzyme was stable at pH ranging from 9.0 to 9.5. The mol wt was calculated to be 61,900-62,700 by SDS-PAGE and gel-filtration technique. The apparent Km value of the bilirubin oxidase was calculated to be 9.4 x 10(-5) mol/L. The enzyme activity was greatly reduced by incubation of bilirubin oxidase with Fe2+, Hg+, NaN3, NH+4, and Zn2+. The enzyme reaction was inhibited in the presence of Ca2+, Hg+, Zn2+, Fe2+, and BSA.     

Novel potentiometric membrane sensor for the determination of trace amounts of chromium(III) ions.

A plasticized Cr3+ ion sensor by incorporating 2,3,8,9-tetraphenyl-1,4,7,10-tetraazacyclododeca-1,3,7,9-tetraene (TTCT) ionophore exhibits a good potentiometric response for Cr3+ over a wide concentration range (1.0 x 10(-6)-1.0 x 10(-1) M) with a slope of 19.5 mV per decade. The sensor response is stable for at least three months. Good selectivity for Cr3+ in comparison with alkali, alkaline earth, transition and heavy metal ions, and minimal interference are caused by Li+, Na+, K+, Co2+, Hg2+, Ca2+, Pb2+ and Zn2+ ions, which are known to interfere with other chromium membrane sensors. The TTCT-based electrode shows a fast response time (15 s), and can be used in aqueous solutions of pH 3-5.5. The proposed sensor was used for the potentiometric titration of Cr3+ with EDTA and for a direct potentiometric determination of Cr3+ content in environmental samples.     

EPR parameters and local geometry for Cr3+ and V2+ ions in HfS2 crystals

From the high-order perturbation formulas of EPR parameters (zero-field splitting D, g factors gparallel, gperpendicular and hyperfine structure constants Aparallel, Aperpendicular) based on the two spin-orbit coupling parameter model for 3d3 ions in trigonal symmetry, the EPR parameters of Cr3+ and V2+ ions in HfS2 crystals are calculated. From the calculations, it is found that the local trigonal distortion angle theta of impurity center in HfS2:Cr3+ is smaller than that in HfS2:V2+. The dominant cause of the small zero-field splitting |D| and g-anisotropy |Deltag|=|gparallel-gperpendicular| in HfS2:Cr3+ (compound to HfS2:V2+) is due to the small local trigonal distortion angle theta rather than to the small impurity-ligand distance R in HfS2:Cr3+.     

溶胶-凝胶及水热法制备掺杂铁、铬离子的二氧化钛光催化剂

通过溶胶 凝胶法结合水热处理制备了掺杂铁或铬离子的纳米尺寸锐钛矿型TiO₂光催化剂.用XRD、BET、TEM、EPR和UV VisDRS对样品进行了系列表征.在对活性偶氮染料XRG的降解中,可见光激发下适量掺杂的TiO₂呈现出优于纯TiO₂和P25的活性,同时掺杂并未降低其在紫外光激发下的活性.     

过渡金属离子与乙腈团簇的反应

用激光溅射-分子束技术,研究了几种过渡金属离子与乙腈团簇分子的气相化 学反应,根据反射式飞行时间质谱检测的结果,不同的过渡金属离子可与乙腈分子 形成不同尺寸的团簇离子产物,其中Ti~+,V~+,Cr~+与乙腈反应的活泼性强于 Cu~+,Fe~+与乙腈反应的活泼性。分析过渡金属离子Ti~+,V~+,Cr~+与乙腈反应 所生成团簇离子的强度分布,发现它们都在n = 2和n = 3之间形成明显的强度间隙 。