Effect of amine double-functionalization on CO<Subscript>2</Subscript> adsorption behaviors of silica gel-supported adsorbents

Amine double-functionalized adsorbents were fabricated using silica gel as supports and their capabilities for CO₂ capture were examined. Aminopropyltrimethoxysilane (1N-APS), and N¹-(3-trimethoxysilylpropyl)diethylenetriamine (3N-APS) were used as grafted amine compounds, and tetraethylenepentamine and polyethyleneimine were used as impregnated species. The influence of double-functionalization method on the CO₂ adsorption performance and textural properties of adsorbents was investigated. The adsorption capacity, the amine efficiency, and the thermal stability of double-functionalized sorbents depend strongly upon molecular variables associated with two different functional states (i.e., chemically grafted and physically impregnated amines). The temperature dependence of adsorption isotherms reveals that the CO₂ adsorption behavior in the double-functionalized adsorbents follow the diffusion limitation model proposed by Xu et al. (Energy Fuels 16:1463–1469, 2002) where the CO₂ adsorption is helped by the diffusion of impregnated amines. It is also found that the adsorption isotherm in the double-functionalized sorbent system with a proper choice for grafted and impregnated amines is nearly independent of temperature, which may offer a novel means to fabricate practically useful sorbents that can be used in a wide range of temperature without loss of CO₂ adsorption capacity.     

Dry Potassium-Based Sorbents for CO<Subscript>2</Subscript> Capture

Dry potassium-based sorbents were prepared by impregnation with potassium carbonate on supports such as activated carbon (AC), TiO₂, Al₂O₃, MgO, CaO, SiO₂ and various zeolites. The CO₂ capture capacity and regeneration property of various sorbents were measured in the presence of H₂O in a fixed bed reactor, during multiple cycles at various temperature conditions (CO₂ absorption at 50–100 °C and regeneration at 130–400 °C). The KAlI30, KCaI30, and KMgI30 sorbents formed new structures such as KAl(CO₃)₂(OH)₂, K₂Ca(CO₃)₂, K₂Mg(CO₃)₂, and K₂Mg(CO₃)₂·4(H₂O), which did not completely convert to the original K₂CO₃ phase at temperatures below 200 °C, during the CO₂ absorption process in the presence of 9 vol.% H₂O. In the case of KACI30, KTiI30, and KZrI30, only a KHCO₃ crystal structure was formed during CO₂ absorption. The formation of active species, K₂CO₃·1.5H₂O, by the pretreatment with water vapor and the formation of the KHCO₃ crystal structure after CO₂ absorption are important factors for absorption and regeneration, respectively, even at low temperatures (130–150 °C). In particular, the KTiI30 sorbent showed excellent characteristics with respect to CO₂ absorption and regeneration in that it satisfies the requirements of a large amount of CO₂ absorption (87 mg CO₂/g sorbent) without the pretreatment with water vapor, unlike KACI30, and a fast and complete regeneration at a low temperature condition (1 atm, 150 °C). In addition, the higher total CO₂ capture capacity of KMgI30 (178.6 mg CO₂/g sorbent) than that of the theoretical value (95 mg CO₂/g sorbent) was explained through the contribution of the absorption ability of MgO support. In this review, we introduce the CO₂ capture capacities and regeneration properties of several potassium-based sorbents, the changes in the physical properties of the sorbents before/after CO₂ absorption, and the role of water vapor and its effects on CO₂ absorption.     

聚乙烯亚胺修饰的氧化硅纳米管基吸附剂的制备及其CO_2吸附应用

以P123为模板,1,2-二(三甲氧基硅基)乙烷(BTME)为硅源合成了介孔氧化硅纳米管(E-SNTs).将ESNTs经过聚乙烯亚胺(PEI)修饰后制得吸附剂用于捕捉CO2.对吸附剂进行了透射电镜(TEM)、物理吸附、傅里叶变换红外(FTIR)光谱、热重分析(TGA)等表征.E-SNTs-PEI吸附剂的最佳CO2吸附温度为75°C.吸附剂的CO2吸附量随着PEI负载量的增加呈现先增大后减小的趋势,其中50%为最佳负载量,此时吸附剂的吸附量最大为3.32 mmol·g-1.相比较SBA-15基吸附剂,E-SNTs基吸附剂具有更优异的吸附性能.在有水汽的存在下,吸附剂E-SNTs-50的CO2吸附量达到3.75 mmol·g-1.经过四次循环吸脱附实验测试E-SNTs-PEI吸附剂的稳定性能,结果表明其CO2吸附量基本不变,该吸附剂表现出较好的稳定性和可再生能力.     

Postsynthetic amine modification of porous organic polymers for CO2 capture and separation

Porous organic polymers (POPs) constitute an important class of sorbents studied in various adsorption and separation processes. Their unique properties, including high surface areas, adjustable pore sizes, and surface chemistries make them ideal candidates for CO₂ capture. To achieve a high CO₂ adsorption capacity and selectivity, particularly at the low partition pressures required for post-combustion CO₂ capture or direct capture of CO₂ from the atmosphere, incorporating amines onto the polymer frameworks or within the pores has shown much promise. This review provides a comprehensive summary of recent studies on the synthesis and CO₂ capture performance of amine-functionalized POPs. The review also provides a detailed discussion of structure-performance relationships, focusing on how the loading amount and amine type influence CO₂ capture capacity, CO₂/N₂ selectivity, heat of adsorption, sorption kinetics, and recyclability of POPs. Additionally, the authors offer their perspective on the challenges associated with the practical implementation of amine-modified POPs for CO₂ capture.     

Preparation and performance of potassium-based sorbent using SnO<Subscript>2</Subscript> for post-combustion CO<Subscript>2</Subscript> capture

Potassium-based sorbents using γ-Al₂O₃ or TiO₂ as a support or an additive material have disadvantages in terms of their thermal stability and cyclic CO₂ capture. To overcome the shortcomings of these sorbents, a novel potassium-based sorbent (KSnI30) using SnO₂ was developed in this study. The KSnI30 sorbent formed only K₂CO₃ and SnO₂ phases without any inactive alloy species even after calcination at high temperatures (500–700 °C), indicating the good thermal stability of the KSnI30 sorbent regardless of the calcination temperature. Furthermore, the KSnI30 sorbent has an excellent regeneration property (above 98 %), as well as high CO₂ capture capacities (89–94 mg CO₂/g sorbent). Its excellent regeneration property is due to the formation of a KHCO₃ phase without by-products during CO₂ sorption. These results of the present study demonstrate that the SnO₂ shows promise as a new support or an additive material to replace TiO₂ and γ-Al₂O₃ in the preparation of a regenerable potassium-based sorbent for post-combustion CO₂ capture with good thermal stability and excellent regeneration property.     

High temperature adsorption of CO<Subscript>2</Subscript> on various hydrotalcite-like compounds

A study was conducted to describe and quantify how substitution of the divalent cation and interlayer charge compensating anions affect the CO₂ adsorptive capacity of various hydrotalcite-like compounds (HTlcs). Physical and chemical properties of the HTlcs were evaluated using a number of methods and the CO₂ adsorption rate and capacity were measured at elevated temperature (603 K). The results showed that the synthetic analogue of the naturally occurring hydrotalcite mineral, [Mg_0.73Al_0.27(OH)₂](CO₃)_0.13⋅xH₂O, had the best overall adsorption capacity and kinetics. The stability of the adsorption capacity was tested by subjecting the model HTlc to 10 equilibrium adsorption and desorption cycles. At the end of the cycle, the HTlc had maintained approximately sixty-five percent of its initial capacity. Temperature programmed desorption of CO₂ was used to quantify the surface basicity of the various HTlcs. The results showed that the reversible physisorption portion of the CO₂ isotherm was correlated to the number of surface basic sites on the HTlcs.     

Regulating Extra-Framework Cations in Faujasite Zeolites for Capture of Trace Carbon Dioxide

The development of cost-effective sorbents for direct capture of trace CO₂ (<1 %) from the atmosphere is an important and challenging task. Natural or commercial zeolites are promising sorbents, but their performance in adsorption of trace CO₂ has been poorly explored to date. A systematic study on capture of trace CO₂ by commercial faujasite zeolites reveals that the extra-framework cations play a key role on their performance. Under dry conditions, Ba−X displays high dynamic uptake of 1.79 and 0.69 mmol g⁻¹ at CO₂ concentrations of 10000 and 1000 ppm, respectively, and shows excellent recyclability in the temperature-swing adsorption processes. K−X exhibits perfect moisture resistance, and >95 % dry CO₂ uptake can be preserved under relative humidity of 74 %. In situ solid-state NMR spectroscopy, synchrotron X-ray diffraction and neutron diffraction reveal two binding sites for CO₂ in these zeolites, namely the basic framework oxygen atoms and the divalent alkaline earth metal ions. This study unlocks the potential of low-cost natural zeolites for applications in direct air capture.     

FT-IR study on CO<Subscript>2</Subscript> adsorbed species of CO<Subscript>2</Subscript> sorbents

The stability of amine-functionalized silica sorbents prepared through the incipient wetness technique with primary, secondary, and tertiary amino organosilanes was investigated. The prepared sorbents were exposed to different gaseous streams including CO₂/N₂, dry CO₂/air with varying concentration, and humid CO₂/air mixtures to demonstrate the effect of the gas conditions on the CO₂ adsorption capacity and the stability of the different amine structures. The primary and secondary amine-functionalized adsorbents exhibited CO₂ sorption capacity, while tertiary amine adsorbent hardly adsorbed any CO₂. The secondary amine adsorbent showed better stability than the primary amine sorbent in all the gas conditions, especially dry conditions. Deactivation species were evaluated using FT-IR spectra, and the presence of urea was confirmed to be the main deactivation product of the primary amine adsorbent under dry condition. Furthermore, it was found that the CO₂ concentration can affect the CO₂ sorption capacity as well as the extent of degradation of sorbents.     

High-performance CO<Subscript>2</Subscript> capture on amine-functionalized hierarchically porous silica nanoparticles prepared by a simple template-free method

The adsorption of CO₂ on polyethyleneimine (PEI)-functionalized hierarchically porous silica nanoparticles (PSNs), prepared by using rice husk as a silica source via a simple template-free method, was reported in this study. Compared with traditional alkaline fusion and surfactant-templating methods for preparing waste-derived porous silica materials as CO₂ adsorbents, this method holds specific important advantages in being an inexpensive, and energy-saving process with faster production rate. The results revealed that the (NH₄)₂SiF₆ salt formed during the synthetic process served as an effective porogen, which can be readily removed by washing with water. Additionally, the total pore volumes of PSNs materials were strongly correlated to the amount of (NH₄)₂SiF₆. When evaluated as a support of PEI for CO₂ adsorption, 55PEI/PSNs(12/14) could reach 159 mg/g at 75 °C under 15 % CO₂, which was remarkably superior to those using waste silicate precursors reported in the previous literature. It was demonstrated that both PEI loading, and total pore volume of the PEI/silica composite sorbents, played key roles on CO₂ adsorption. Besides, 55PEI/PSNs(12/14) also showed high stability during 20 cycles of adsorption–desorption operation, implying its high potential in post-combustion CO₂ capture.     

Capture of CO<Subscript>2</Subscript> from flue gas by vacuum pressure swing adsorption using activated carbon beads

Vacuum pressure swing adsorption (VPSA) for CO₂ capture has attracted much research effort with the development of the novel CO₂ adsorbent materials. In this work, a new adsorbent, that is, pitch-based activated carbon bead (AC bead), was used to capture CO₂ by VPSA process from flue gas. Adsorption equilibrium and kinetics data had been reported in a previous work. Fixed-bed breakthrough experiments were carried out in order to evaluate the effect of feed flowrate, composition as well as the operating pressure and temperature in the adsorption process. A four-step Skarstrom-type cycle, including co-current pressurization with feed stream, feed, counter-current blowdown, and counter-current purge with N₂ was employed for CO₂ capture to evaluate the performance of AC beads for CO₂ capture with the feed compositions from 15–50% CO₂ balanced with N₂. Various operating conditions such as total feed flowrate, feed composition, feed pressure, temperature and vacuum pressure were studied experimentally. The simulation of the VPSA unit taking into account mass balance, Ergun relation for pressure drop and energy balance was performed in the gPROMS using a bi-LDF approximation for mass transfer and Virial equation for equilibrium. The simulation and experimental results were in good agreement. Furthermore, two-stage VPSA process was adopted and high CO₂ purity and recovery were obtained for post-combustion CO₂ capture using AC beads.     

Facile Synthesis of Polyethylenimine and Nano-TiO<Subscript>2</Subscript> Particles Functionalized PolyHIPE Beads for CO<Subscript>2</Subscript> Capture

Polyethylenimine (PEI) and titanium dioxide nanoparticles (nano-TiO₂) functionalized poly- HIPE beads were synthesized by suspension polymerization of styrene/divinylbenzene high internal phase emulsion (HIPE) containing PEI and nano-TiO₂ particles in inner phase. The products are uniform and spherical beads with average diameter of 1 mm. Characterization results showed good thermal stability and desired mechanical strength. CO₂ adsorption tests were performed with CO₂/H₂O/N₂ (1 : 1 : 8) gas mixture. Nano-TiO₂ particles distinctly improved the CO₂ adsorption performance of the polyHIPE beads, resulting in enhanced CO₂ adsorption capacity and fast adsorption/desorption kinetics. Besides, the functionalized polyHIPE beads exhibited remarkable cycle stability.     

五乙烯六胺修饰的MCF基吸附剂的制备及其CO2吸附性能研究

以三嵌段共聚物P123 (EO₂₀-PO₇₀-EO₂₀)为模板剂合成了介孔泡沫氧化硅(MCF)材料. MCF经过五乙烯六胺(PEHA)修饰后用于捕捉CO₂. 采用扫描电镜(SEM)、透射电镜(TEM)、N2吸附-脱附、傅里叶变换红外(FTIR)光谱、热重分析(TGA)对MCF和MCF-PEHA进行了表征. 结果表明, PEHA对MCF改性后, 并没有破坏MCF载体本身的结构. MCF-PEHA的CO₂吸附量在75℃时达到最大. 随着PEHA含量的增加, MCF-PEHA的CO₂吸附量呈先增大后减小的趋势, 当PEHA含量为70% (w)时, CO₂吸附量达到最大, 为3.55 mmol·g^-1. 水汽促进了吸附剂的CO₂吸附性能. 研究结果还表明, MCF-70吸附剂经过四次吸脱附循环, 吸附性能基本保持不变, 表现出很好的可再生性能.     

Effect of various aminosilanes functionalized inside nanoporous silica on CO<Subscript>2</Subscript> adsorption performance

Three different aminosilanes ((3-aminopropyl)trimethoxysilane (1NS), N-[3-(trimethoxysilyl) propyl]ethylenediamine (2NS), N¹-(3-trimethoxysilylpropyl)diethylenetriamine (3NS)) were grafted covalently inside nanoporous silica (NPS-1) with a large surface area to prepare CO₂ adsorbents. The prepared CO₂ sorbents were evaluated for their CO₂ sorption capacity, kinetic behavior, temperature programmed desorption (TPD) and textural properties. Grafting efficiency of 1NS was better due to the smaller molecular size compared to 2NS and 3NS, which are difficult to react with the hydroxyl group of the silica surface due to steric hindrance. The highest adsorption capacity of 7.0 wt% was observed for the 2NS/NPS-1 adsorbent, followed by 5.2 wt% for 1NS/NPS-1, then 5.0 wt% for 3NS/NPS-1. The adsorption capacity of 2NS/NPS-1 was highest at 30 °C, and it gradually decreased as the adsorption temperature increased. TPD analysis showed that the reaction of primary amine of 2NS with CO₂ inside the nanoporous silica could form less thermally stable carbamic acid and carbamate compared to 1NS and 3NS.     

Zeolite synthesis from waste fly ash and its application in CO<Subscript>2</Subscript> capture from flue gas streams

Zeolite A and A + X mixtures were prepared from coal-fly ash procured from China by using an alkali fusion method. X-ray diffraction showed that both the materials were crystalline and reproducible. Scanning Microscopy revealed that pure zeolite A particles have cubic morphology while the mixture shows intergrowth of cubic and pyramidal crystals. The surface area for A + X mixture was around 330 m²/g which is higher than zeolite A, however, lower than typical X zeolite. CO₂ and N₂ adsorption isotherms were measured and the data was fitted by the Dual Site Langmuir equation. These zeolites were then tested for CO₂ capture at different temperatures in a process with a nine step cycle. When compared with 13X zeolites at higher temperature (∼90 °C), both the zeolite A + X mixture and zeolite A prepared from fly ash showed better performance in CO₂ capture from flue gas because they have higher selectivity of CO₂ over N₂.     

Preparation and characterization of waste ion-exchange resin-based activated carbon for CO<Subscript>2</Subscript> capture

Waste ion-exchange resin was utilized as precursor to produce activated carbon by KOH chemical activation, on which the effects of different activation temperatures, activation times and impregnation ratios were studied in this paper. The CO₂ adsorption of the produced activated carbon was tested by TGA at 30 °C and environment pressure. Furthermore, the effects of preparation parameters on CO₂ adsorption were investigated. Experimental results show that the produced activated carbons are microporous carbons, which are suitable for CO₂ adsorption. The CO₂ adsorption capacity increases firstly and then decreases with the increase of activation temperature, activation time and impregnation rate. The maximum adsorption capacity is 81.24 mg/g under the condition of 30 °C and pure CO₂. The results also suggest that waste ion-exchange resin-based activated carbons possess great potential as adsorbents for post-combustion CO₂ capture.     

Metal–Organic Frameworks with Target‐Specific Active Sites Switched by Photoresponsive Motifs: Efficient Adsorbents for Tailorable CO2 Capture

Photoresponsive metal–organic frameworks (PMOFs) are of interest for tailorable CO₂ adsorption. However, modulation of CO₂ adsorption on PMOFs is based on steric hindrance or structural change owing to weak interactions between CO₂ and active sites. It is challenging to fabricate PMOFs with strong but tailorable sites for CO₂ adsorption. Now, the construction of PMOFs with target‐specific (strong) active sites is achieved by introducing tetraethylenepentamine into azobenzene‐functionalized MOFs for tailorable CO₂ adsorption. Amines are specific active sites for CO₂, contributing to capture CO₂ selectively. Cis/trans isomerization of azobenzene motifs trigged by UV/Vis light adjusts the electrostatic potential of amines significantly, leading to exposure/shelter of amines and modulation of CO₂ adsorption on strong active sites. This system enables us to design adsorption processes for CO₂ capture from mixtures, which is impossible to realize by traditional PMOFs.     

Tandem Mass Spectrometry Measurement of the Collision Products of Carbamate Anions Derived from CO<Subscript>2</Subscript> Capture Sorbents: Paving the Way for Accurate Quantitation

The reaction between CO₂ and aqueous amines to produce a charged carbamate product plays a crucial role in post-combustion capture chemistry when primary and secondary amines are used. In this paper, we report the low energy negative-ion CID results for several anionic carbamates derived from primary and secondary amines commonly used as post-combustion capture solvents. The study was performed using the modern equivalent of a triple quadrupole instrument equipped with a T-wave collision cell. Deuterium labeling of 2-aminoethanol (1,1,2,2,-d₄-2-aminoethanol) and computations at the M06-2X/6-311++G(d,p) level were used to confirm the identity of the fragmentation products for 2-hydroxyethylcarbamate (derived from 2-aminoethanol), in particular the ions CN⁻, NCO⁻ and facile neutral losses of CO₂ and water; there is precedent for the latter in condensed phase isocyanate chemistry. The fragmentations of 2-hydroxyethylcarbamate were generalized for carbamate anions derived from other capture amines, including ethylenediamine, diethanolamine, and piperazine. We also report unequivocal evidence for the existence of carbamate anions derived from sterically hindered amines (Tris(2-hydroxymethyl)aminomethane and 2-methyl-2-aminopropanol). For the suite of carbamates investigated, diagnostic losses include the decarboxylation product (−CO₂, 44 mass units), loss of 46 mass units and the fragments NCO⁻ (m/z 42) and CN⁻ (m/z 26). We also report low energy CID results for the dicarbamate dianion (⁻O₂CNHC₂H₄NHCO₂⁻) commonly encountered in CO₂ capture solution utilizing ethylenediamine. Finally, we demonstrate a promising ion chromatography-MS based procedure for the separation and quantitation of aqueous anionic carbamates, which is based on the reported CID findings. The availability of accurate quantitation methods for ionic CO₂ capture products could lead to dynamic operational tuning of CO₂ capture-plants and, thus, cost-savings via real-time manipulation of solvent regeneration energies.     

A Rational Design of Microporous Aerogel for Excellent CO<Subscript>2</Subscript> Capture and Selectivities via Co-Synergistic Effects of Electrostatic In-plane and π–π Stacking Interactions

Microporous aerogel (PEINK) with a nitrogen-containing framework, high CO₂ capture and selectivity were obtained through the condensation polymerization of 1,3,5-tris-(4-fluorobenzoyl)benzene with 5-hydroxyindol. The uptake capacity for CO₂ reached up to 17.7 wt % (1.0 bar, 273 K), and the high CO₂/N₂ = 16, CO₂/CH₄ = 29 selectivity. Density functional theory illustrated that a CO₂ molecular was captured via synergistic efforts with π–π stacking of indole group and electrostatic in-plane binding of an adjacent ether unit, thus the selectivity and adsorption of CO₂ were strengthen. The proposed co-synergistic effect on one CO₂ molecular is expected to be a new theory for the design of high CO₂ capture materials.     

Equilibrium isotherms and isosteric heat for CO<Subscript>2</Subscript> adsorption on nanoporous carbons from polymers

Four nanoporous carbons obtained from different polymers: polypyrrole, polyvinylidene fluoride, sulfonated styrene–divinylbenzene resin, and phenol–formaldehyde resin, were investigated as potential adsorbents for carbon dioxide. CO₂ adsorption isotherms measured at eight temperatures between 0 and 60 °C were used to study adsorption properties of these polymer-derived carbons, especially CO₂ uptakes at ambient pressure and different temperatures, working capacity, and isosteric heat of adsorption. The specific surface areas and the volumes of micropores and ultramicropores estimated for these materials by using the density functional theory-based software for pore size analysis ranged from 840 to 1990 m² g^?1, from 0.22 to 1.47 cm³ g^?1, and from 0.18 to 0.64 cm³ g^?1, respectively. The observed differences in the nanoporosity of these carbons had a pronounced effect on the CO₂ adsorption properties. The highest CO₂ uptakes, 6.92 mmol g^?1 (0 °C, 1 atm) and 1.89 mmol g^?1 (60 °C, 1 atm), were obtained for the polypyrrole-derived activated carbon prepared through a single carbonization-KOH activation step. The working capacity for this adsorbent was estimated to be 3.70 mmol g^?1. Depending on the adsorbent, the CO₂ isosteric heats of adsorption varied from 32.9 to 16.3 kJ mol^?1 in 0–2.5 mmol g^?1 range. Overall, the carbons studied showed well-developed microporosity and exceptional CO₂ adsorption, which make them viable candidates for CO₂ capture, and for other adsorption and environmental-related applications.