增容剂对聚对苯二甲酸乙二酯/聚丙烯共混体系结构流变学的影响

采用马来酸酐接枝聚丙烯(PP-g-MAH)对聚丙烯/聚对苯二甲酸乙二酯(PP/PET)共混体系进行增容,研究了增容前后复合体系的相形态和流变行为的变化.结果表明,共混体系中当PP组分为分散相时,增容剂能够显著减小PP液滴尺寸,使其形状松弛时间减小,变形与破裂的剪切敏感性降低;当共混体系两组分配比处于临界相反转点周围时,增容剂则会导致其内部部分双连续与“海-岛”结构共存的复杂相形态消失,低频区模量频率依赖性的增加表明体系内部界面结合程度的增加;而当共混体系中的PET组分为分散相时,增容剂的引入对体系结构流变学影响较小,表明增容效果不大.     

纳米SiO_2/聚丙烯复合材料的反应性增容

利用反应性增容技术制备了纳米二氧化硅/聚丙烯复合材料.首先探讨了将甲基丙烯酸缩水甘油酯-丙烯酸丁酯共聚物接枝到纳米二氧化硅粒子表面进行改性的各种影响因素,然后将接枝改性纳米二氧化硅与聚丙烯以及作为反应性增容剂的氨基化聚丙烯共混.结果表明,改性粒子上的环氧基与氨基化聚丙烯上的氨基之间的化学反应大大增强了复合材料的界面作用,从而在粒子含量很低时明显提高了聚丙烯的拉伸强度、模量和冲击强度.     

PP－g－PMMA在PP／PVDF共混体系中的应用

利用聚丙烯等离子体接枝甲基丙烯酸甲酯共聚物（ＰＰ－ｇ－ＰＭＭＡ）作增容剂，研究了其在聚丙烯／聚偏氟乙烯（ＰＶＤＦ）共混体系中的作用。增容是通过ＰＭＭＡ与ＰＶＤＦ的偶极－偶极相互作用实现的。接枝共聚物使共混体系的抗张强度和模量均有提高，由不同等离子体处理时间所得的ＰＰ－ｇ－ＰＭＭＡ，接枝率在７．７％～３００％具有最好的增容效果；而由不同后聚合时间所得的共聚物，接枝率在３０％～８０％具有最好的增容效果。     

增容剂对煤直接液化残渣改性沥青低温性能的影响

为了评价不同增容剂对煤直接液化残渣改性沥青低温性能的影响,首先,通过正交实验确定出三种增容剂（硅烷偶联剂、苯甲醛、二甲苯）各自的最佳掺量及掺入方式;其次,采用双边缺口拉伸（DENT）试验评价加入三种增容剂后沥青的低温抗延性断裂性能;最后,结合SEM照片并利用Image Pro plus图像处理软件计算加入三种增容剂后沥青中煤直接液化残渣的分散面积比,以定量地表征三种增容剂对煤直接液化残渣改性沥青低温性能的改善效果。结果表明,加入适量增容剂在一定程度上有助于煤直接液化残渣在沥青中的分散,提高两者之间的相容性,保持煤直接液化残渣改性沥青体系的长期稳定状态,避免因煤直接液化残渣的沉淀聚集而在相界面产生应力集中,增强煤直接液化残渣改性沥青的低温抗延性断裂性能。三种增容剂对煤直接液化残渣改性沥青低温性能改善效果不同,硅烷偶联剂最优,次之为苯甲醛,最差为二甲苯。     

PP/PP-g-MAH/PA6共混物结构与可纺性研究

运用DSC、SEM、纺丝成形等手段研究了增容剂聚丙烯接枝马来酸酐 (PP g MAH)对聚丙烯 聚酰胺 6(PP PA6 )共混物结构和性能的影响 .结果表明 ,共混物呈典型海岛型两相结构 ;增容剂PP g MAH与PA6之间的在位反应改善了PP PA6共混体系的相容性 ,使共混物中PA6的热结晶峰消失 ,PP的结晶生长速率和成核速率降低 ,可纺性提高     

反应挤出合成带不饱和官能团端基的聚己内酯

用带双键官能团的2-烯丙氧基乙醇与四丙醇钛酸酯进行酯交换,可合成用于ε-己内酯配位开环聚合的钛化合物引发剂;利用此引发剂,引发ε-己内酯聚合得到了分子链一端为双键的功能化聚己内酯.研究了物料配比和反应温度对聚合转化率和速率的影响,进而在双螺杆挤出机中实施快速本体聚合,合成了带活性双键的功能化聚己内酯.引发剂和聚合物的化学结构由 1H-NMR予以表征,GPC测定的结果表明聚合物的分子量与物料摩尔比相关.     

等规聚丙烯离聚体增容聚丙烯/尼龙11共混体系研究

以碘代等规聚丙烯为大分子反应中间体,通过季胺化亲核取代反应和点击化学反应,制备了N-甲基咪唑聚丙烯离聚体(IA)和邻巯基苯胺盐酸盐聚丙烯离聚体(IB),并将其作为等规聚丙烯/生物基尼龙11 (i PP/PA11)共混体系的增容剂.通过动态力学分析(DMA)、扫描电镜(SEM)和力学性能测试,对i PP/PA11/聚丙烯离聚体三元共混体系的相形态与性能进行了系统研究. DMA测试结果显示,2种聚丙烯离聚体使i PP/PA11共混体系的玻璃化转变温度Tg相互靠近;SEM结果显示,离聚体的加入使分散相粒子尺寸显著减小,两相界面作用力增加;力学性能测试表明,i PP/PA11/IA、i PP/PA11/IB三元共混体系的拉伸强度和冲击强度保持较好的水平.以上研究结果表明,IA和IB均可以显著改善i PP/PA11共混体系的相容性.     

反应性杂化纳米粒子的合成及其对不相容共混物的增容研究

采用八环氧多面体低聚倍半硅氧烷(POSS(epoxy)8)和端羧基聚甲基丙烯酸甲酯(PMMA-COOH)的开环反应,运用Graft-onto的方法合成了一种反应性杂化纳米粒子:四环氧多面体低聚倍半硅氧烷-接枝-四聚甲基丙烯酸甲酯(POSS(epoxy)4-g-PMMA4).通过傅里叶红外光谱仪(FTIR),示差扫描量热仪(DSC),热失重分析仪(TGA),核磁共振波谱仪(1H-NMR)等对反应性杂化纳米粒子的结构进行了表征,结果表明成功合成了POSS(epoxy)4-g-PMMA4.并将上述合成的反应性杂化纳米粒子应用于聚偏氟乙烯/聚乳酸(PVDF/PLLA)不相容体系的增容,运用万能材料试验机、扫描电子显微镜(SEM)和透射电子显微镜(TEM)对其增容原理和效果进行研究,结果表明POSS(epoxy)4-g-PMMA4可以作为PVDF/PLLA不相容体系的反应性增容剂.     

乙酰化稻草/聚己内酯接枝共聚物的合成及表征

以稻草秸秆为原料,经粉碎后进行全植物秸秆的乙酰化改性,再用此乙酰化稻草同ε-己内酯(ε-CL)接枝共聚合成乙酰化稻草/聚己内酯接枝共聚物(ACSW-g-PCL)。研究了反应时间、反应温度、及单体用量对接枝率(G%)的影响。在反应温度140℃,反应时间10h,ε-CL对乙酰化稻草的质量比2:1时获得的接枝率最大为39%。产物的结构和性能通过红外光谱、核磁共振、扫描电镜、X-射线衍射和热分析仪表征,结果表明乙酰化稻草秸秆已成功接枝上聚己内酯(PCL)链段,经接枝ε-CL改性后的ACSW-g-PCL热稳定性有所改善,并具有了一定的热塑性。     

HDPE/PA6反应增容体系的形态演化与黏弹行为

采用扫描电子显微镜(SEM)与先进流变扩展系统(ARES),研究了马来酸酐接枝高密度聚乙烯(HDPE-g-MAH)对高密度聚乙烯/尼龙6(HDPE/PA6)共混体系形态结构和黏弹行为的影响.发现HDPE-g-MAH的加入可原位生成尼龙6-高密度聚乙烯接枝共聚物(HDPE-g-PA6),使基体与分散相间的相容性显著改善,且随其添加量的增加两者相容性更好,导致HDPE/PA6体系形态结构变化.研究结果表明,由ARES获得的体系黏弹行为参数随HDPE-g-MAH含量的变化可与由SEM所观察到的微观形貌演化很好关联,动态流变学方法可敏感表征增容剂的加入所引起的HDPE/PA6界面性质变化,且能够反映分子链间相互作用的变化及由此导致的分散相颗粒网络的形成.     

Morphology of isotactic polypropylene-polyamide 66 blends and their mechanical properties

Compounds were prepared with isotactic polypropylene (iPP) matrix and recycled polyamide 66 fibres (PA66), which were obtained as soft waste in industrial production process. Blends with pristine PA66 pellets were prepared as comparison. The blends showed the presence of PA66 particles dispersed in the PP continuous phase. Considering the incompatibility of the two polymers the addition of isotactic polypropylene grafted with maleic anhydride (iPPgMA) as compatibilizer was investigated: the blends were characterized by thermal, mechanical, dynamic-mechanical and morphological analyses. The presence of the compatibilizer significantly influences the morphology of the blends, inducing a finer dispersion and promoting interfacial adhesion. The characterization of pristine and recycled PA66 did not show a meaningful difference in the value of molecular weight, on the other hand marked differences were presented in the flexural moduli of the two materials; analogous differences were exhibited by the blends: compounds prepared with recycled PA66 showed flexural moduli higher than compatibilized blends with pristine PA66.     

Influence of hyperbranched polymers on the interfacial tension of polypropylene/polyamide‐6 blends

The compatibilizing effect of polypropylene (PP) grafted with hyperbranched polymers (PP–HBP) has been investigated in PP/polyamide‐6 (PA‐6) blends. Because of its high reactivity and diffusitivity, PP–HBP has been shown to be a more effective compatibilizer in decreasing the interfacial tension than the commonly used maleic anhydride–grafted polypropylene (PP–MAH). This article describes the influence of PP–HBP and PP–MAH on the interfacial tension between PP and PA‐6, as measured by the deformed drop‐retraction method (DDRM). Overall, PP–HBP yielded lower interfacial tension values between PP and PA‐6, which resulted in a finer particle size of the secondary phase. The time dependence of the interfacial tension can be monitored by DDRM, enabling evaluation of the diffusitivity and reactivity of the compatibilizer. A model based on particle coarsening has been developed to describe the time dependence of the interfacial tension. This model showed that the diffusitivity and reactivity for PP–HBP was higher than that of PP–MAH. Therefore, PP–HBP has strong potential as a compatibilizer in diffusitivity‐dependant processes such as film coextrusion and fusion bonding. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2069–2077, 1999     

The effect of various compatibilizers on thermal,mechanical, and morphological properties of polystyrene/polypropylene blends

The effects of various compatibilizers on thermal, mechanical and morphological properties of 50/50 polypropylene/polystyrene blends were investigated. Various compatibilizers, polystyrene-(ethylene/butylenes/ styrene) (SEBS), ethylene vinyl acetate (EVA), polystyrene-butylene rubber (SBR) and blend of compatibilizers SEBS/PP-g-MAH, EVA/PP-g-MAH, and SBR/PP-g-MAH were used. Differential scanning calorimetry, thermogravimetric analysis, wide-angle X-ray scattering, scanning electron microscopy, microhardness, and Izod impact strength were adopted. It was found that the influence of various compatibilizers was appeared on all the properties studied. The properties of the blends compatibilized with SEBS, EVA, and SBR are very distinct from those of blends compatibilized with blend of compatibilizers. Results show that compatibilized blends with the blend of compatibilizers EVA/PP-g-MAH, SBR/PP-g-MAH, and SEBS/PP-g-MAH or SBR were relatively more stable than the uncompatibilized blend and blend compatibilized with SEBS or EVA. The compatibilizer does not only reduce the interfacial tension or increase the phase interfacial adhesion between the immiscible polymers, but greatly affects the degree of crystallinity of blends.

     

Morphology development of immiscible polymer blends during melt blending: Effects of interfacial agents on the liquid-solid interfacial heat transfer

This article reports on a new phenomenon: The presence of a compatibilizer accelerates the melting/plastification of an immiscible polymer blend during melt blending. The increase in the rate of melting as a result of the addition of a compatibilizer is believed to be one of the important factors responsible for the fact that the morphology of compatibilized blends develops much faster than that of their uncompatibilized counterparts. To substantiate the above statement, blends based on polypropylene (PP) and polyamide 6 (PA6) were used as model systems. The compatibilizer was a graft copolymer (PP-g-PA6) with PP as the backbone and PA6 as grafts. Its presence in a PP/PA6 blend accelerated the rate of melting of the PA6. This effect was observed only when the compatibilizer itself was molten and migrated to the interfacial layer between the PA6 and PP phases. It is likely that the presence of the compatibilizer increased the chain entanglements at the PP and PA6 interface and consequently reduced the thermal resistance of the interfacial layer. Detailed mechanisms are discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 3368–3384, 1999     

POE-g-PMAH反应性增容PA1010/PP共混物的性能研究

乙烯-辛烯共聚物-g-聚马来酸酐(POE-g-PMAH)作为反应性增容剂,采用熔体共混的方法制备了PA1010/PP共混物,通过扫描电镜(SEM)、力学性能、傅立叶变换红外光谱(FTIR)和示差扫描量热(DSC)测试,研究了POE-g-PMAH对PA1010/PP共混物的增容作用.结果表明,POE-g-PMAH的加入可以减小共混物的相区尺寸,当PA1010/PP/POE-g-PMAH=70/30/15时,分散相尺寸小而均匀;FTIR结果表明接枝在POE上的马来酸酐基团和PA1010在熔融共混期间发生了化学反应;DSC研究结果表明共混体系中PA1010和PP的结晶温度和结晶度随POE-g-PMAH的加入而降低,表明POE-g-PMAH的增容作用对PA1010和PP的结晶有抑制作用.力学性能测试结果表明随着POE-g-PMAH的增加,共混物的冲击强度逐渐增加,当POE-g-PMAH含量增加到15%时,干态冲击强度达到21.13 kJ/m2,是不加增容剂的3.1倍,而拉伸和弯曲强度可以保持较高水平.POE-g-PMAH的增容机理在于其支链中的马来酸酐能与PA1010中的胺基(NH2—)发生化学反应,而主链POE与PP有较好的亲和性,从而降低界面张力,减少相区尺寸,大幅度提高力学性能.     

离子聚合物在Nylon－1010／PP共混物中的增容作用

离子聚合物在Ｎｙｌｏｎ－１０１０／ＰＰ共混物中的增容作用曲桂杰，刘景江（中国科学院长春应用化学研究所长春１３００２２）关键词聚丙烯，Ｎｙｌｏｎ－１０１０，离子聚合物，增容选择离子聚合物作为高聚物共混的增容剂，通过离子间的相互作用可达到增容效果［１］。...     

Reactive compatibilization of blends of PET and PP modified by GMA grafting

The melt radical grafting of glycidyl methacrylate (GMA) onto isotactic polypropylene (PP) was carried out in Brabender internal mixer and the influence of reaction procedure, radical initiator concentration and addition of co-monomer (styrene) on the grafting efficiency was examined. The viscosity, the thermal behaviour and melt rheology of PP-g-GMA samples was then analysed as a function of grafted GMA content. Blends of poly(ethylene terephthalate) (PET) with PP and PP-g-GMA (5.2 wt% GMA), prepared in internal mixer, were characterised by SEM, DSC and melt viscosimetry. The morphological analysis of PET/PP-g-GMA blends (80/20, 50/50 w/w) pointed out a marked improvement of phase dispersion (with particle size of about 0.6 μm for 80/20 blend) and interfacial adhesion, as compared to non-compatibilized PET/PP blend. The results of mixing torque and thermal analysis supported the occurrence of in-situ compatibilization reaction between epoxy groups of GMA modified PP and carboxyl end-groups of PET in the melt.     

Reactive compatibilization of nylon copolymer/EPDM blends: experimental aspects and their comparison with theory

In situ reactive compatibilization was first time applied to a low melting nylon (nylon 6 and 66 copolymer) and EPDM blend system. The effects of in situ compatibilization and concentration of compatibilizer on the morphology and mechanical properties of nylon/EPDM blends have been investigated. The influence of EPM‐g‐MA on the phase morphology was examined by the scanning electron microscopy (SEM) after preferential extraction of the minor phase. The SEM micrographs were quantitatively analyzed for domain size measurements. The compatibilizer concentrations used were 0, 1, 2.5, 5, and 10 wt%. The graft copolymer (nylon‐g‐EPM) formed at the interface showed relatively high emulsifying activity. A maximum phase size reduction was observed when 2.5 wt% of compatibilizer was added to the blend system. This was followed by a leveling‐off at higher loadings indicating interfacial saturation. The conformation of the compatibilizer at the interface was deduced based on the area occupied by the compatibilizer at the blend interface. The experimental compatibilization results were compared with theoretical predictions of Noolandi and Hong. It was concluded that the molecular state of compatibilizer at interface changes with concentration. The in situ compatibilized blends showed considerable improvement in mechanical properties. Measurement of tensile properties shows increased elongation as well as enhanced modulus and strength up on compatibilization. At higher concentrations of compatibilizer, a leveling‐off of the tensile properties was observed. A good correlation has been observed between the mechanical properties and morphological parameters. Copyright © 2007 John Wiley & Sons, Ltd.     

二元乙丙橡胶的环氧官能化及其增韧尼龙6的研究

在双螺杆挤出机中制备了环氧官能化的二元乙丙橡胶(gEPR) ,采用红外光谱工作曲线法测量了EPR的接枝率.将环氧官能化的EPR与尼龙6 (Nylon- 6 )熔融共混,并对共混体系的相形态、断裂形貌、增韧机理、力学性能进行了研究.结果表明,gEPR的环氧官能团与Nylon- 6的端羧基和(或)端氨基发生了化学反应生成Nylon -6 co EPR共聚物,该共聚物作为界面改性剂降低了Nylon -6与EPR之间的界面张力,使EPR在Nylon -6基体中均匀、稳定地分散,而且随着EPR接枝率的增加,EPR的粒径尺寸逐渐减小.断面形貌观察发现,与Nylon -6 EPR体系相比,Nyon -6 gEPR共混体系呈现明显的韧性断裂特征.通过对Nylon -6 gEPR共混体系缺口冲击形变区的研究得出EPR增韧Nylon -6的机理是橡胶粒子的空洞化和塑料基体的剪切屈服.力学性能测试表明gEPR的引入显著提高了Nylon -6的缺口冲击强度.