Analysis of chloride, bromide and iodide using miniaturised isotachophoresis on a planar polymer chip

A new method has been developed to allow the determination of the halide anions chloride, bromide and iodide using isotachophoresis. This method employs a new electrolyte system which incorporates the novel application of indium(III) as a complexing agent. This electrolyte system was devised based on the findings of an investigation into the potential for using indium(III) as a complexing counter ion to selectively manipulate the effective mobilities of halide ions. A leading electrolyte incorporating 3.5 mmol dm(-3) of indium(III) allowed the simultaneous determination of chloride, bromide and iodide to be successfully achieved. The new procedure allows such separations to be made without interference from common inorganic anions such as sulfate and nitrate. Separations were performed using a miniaturised planar poly(methyl methacrylate) chip with integrated platinum wire conductivity detection electrodes. Using this instrumentation the limits of detection were calculated to be 0.7 mg dm(-3), 1.7 mg dm(-3) and 2.2 mg dm(-3) for chloride, bromide and iodide respectively.     

Simultaneous determination of DTPA,EDTA, and NTA by capillary electrophoresis after complexation with copper

We present a method for simultaneous determination of the aminopolycarboxylic acids DTPA, EDTA and NTA in dishwashing detergents, paper mill waters, and natural waters by capillary electrophoresis (CE). The complexing agents were examined as their copper(II) complexes and separated by conventional CE with reversed polarity of the applied voltage. The optimum separation conditions were established by varying the pH and phosphate and tetradecyltrimethylammonium bromide (TTAB) concentrations in the run buffer. The separations were carried out in a fused-silica capillary (61 cm×75 m i.d.) filled with phosphate buffer (80 mmol L^–1, TTAB concentration 0.5 mmol L^–1, pH 7.1, voltage –20 kV) using direct UV detection at 191 and 254 nm. With this CE method all the peaks in the electropherograms were properly separated, the calibration plots gave good correlation coefficients and all three complexing agents could be detected in less than 4 min. Linear calibration plots were obtained for CuDTPA, CuEDTA and CuNTA; limits of detection were 0.03 mmol L^–1 for all complexing agents and recoveries for all tested samples were within the range 104±7%. Results obtained from dishwashing detergent samples were found to be reliable and comparable with those from HPLC (R²=0.989) and UV–Vis (R²=0.985) methods.     

Spectrophotometric determination of indium(III) with the polymeric chromogenic reagent PV · FPAQ

Summary The polymeric chromogenic reagent PV · FPAQ has been synthesized by condensing 7-(4-formylphenylazo)-8-quinolinol (FPAQ) with poly(vinyl alcohol) (PVA). With indium(III) the reagent forms in weakly acidic media a water-soluble yellow complex, whose absorption maximum is at 445 nm. The molar absorptivity of the complex was found to be 3.16×10⁴ l · mol^–1 · cm^–1 and Sandell's sensitivity 3.6 ng · cm^–2. Beer's law is obeyed over the range 0–30 g of indium(III) per 25 ml of solution. A Spectrophotometric method for the determination of indium has been worked out and applied to synthetic and authentic samples with satisfactory results.

---

Spektrophotometrische Bestimmung von Indium(III) mit dem polymeren chromogenen Reagens PV · FPAQ

---

Lecture given at the 2nd National Symposium for Inorganic Micro and Trace Analysis, Xi-An, Peoples Republic of China, September 1988 (see [3])     

Selective extraction of U(VI), Th(IV), and La(III) from acidic matrix solutions and environmental samples using chemically modified Amberlite XAD-16 resin

A new grafted polymer has been developed by the chemical modification of Amberlite XAD-16 (AXAD-16) polymeric matrix with [(2-dihydroxyarsinoylphenylamino)methyl]phosphonic acid (AXAD-16-AsP). The modified polymer was characterized by a combination of ¹³C CPMAS and ³¹P solid-state NMR, Fourier transform-NIR-FIR-Raman spectroscopy, CHNPS elemental analysis, and thermogravimetric analysis (TGA). The distribution studies for the extraction of U(VI), Th(IV), and La(III) from acidic solutions were performed using an AXAD-16-AsP-packed chromatographic column. The influences of various physiochemical parameters on analyte recovery were optimized by both static and dynamic methods. Accordingly, even under high acidities (>4 M), good distribution ratio (D) values (10²–10⁴) were achieved for all the analytes. Metal ion desorption was effective using 1 mol L^–1 (NH₄)₂CO₃. From kinetic studies, a time duration of <15 min was sufficient for complete metal ion saturation of the resin phase. The maximum metal sorption capacities were found to be 0.25, 0.13, and 1.49 mmol g^–1 for U(VI); 0.47, 0.39, and 1.40 mmol g^–1 for Th(IV); and 1.44, 1.48, and 1.12 mmol g^–1 for La(III), in the presence of 2 mol L^–1 HNO₃, 2 mol L^–1 HCl, and under pH conditions, respectively. The analyte selectivity of the grafted polymer was tested in terms of interfering species tolerance studies. The system showed an enrichment factor of 365, 300, and 270 for U(VI), Th(IV), and La(III), and the limit of analyte detection was in the range of 18–23 ng mL^–1. The practical applicability of the polymer was tested with synthetic nuclear spent fuel and seawater mixtures, natural water, and geological samples. The RSD of the total analytical procedure was within 4.9%, thus confirming the reliability of the developed method.     

Development and Validation of a Capillary Electrophoresis Method for the Determination of Denatonium Benzoate in Denaturated Alcohol Formulations

Capillary electrophoretic (CE) technique was investigated for the rapid analysis of denatonium benzoate (Bitrex), a quaternary ammonium salt, in several denaturated alcohol formulations. The optimized separations were carried out in 0.025 mol L^–1 Tris-phosphate electrolyte (pH 7.0) using direct UV detection at 214 nm. In order to prevent precipitation of hydrophobic matrix components in aqueous electrolyte, an electrokinetic sample introduction mode with internal standard (triethylbenzylammonium chloride) was used. Valid calibration (r²=0.998) was demonstrated in the range 2-50 mg L^–1 of Bitrex. The detection limit determined for 10 s electrokinetic (5 kV) injection was 0.45 mg L^–1 (three times the baseline noise). The proposed method was applied to the determination of Bitrex in various Lithuanian denaturated alcohol formulations and the results were statistically comparable with those obtained by HPLC technique.     

Rapid determination of telmisartan in pharmaceuticals and serum by the parallel catalytic hydrogen wave method

The polarographic characteristics of telmisartan have been investigated in 0.8 mol L^–1 NH₃.H₂O–NH₄Cl (pH 8.9)–0.01 mol L^–1 H₂O₂ as supporting electrolyte. The results demonstrate that the polarographic reduction wave at ca. –1.30 V in the absence of H₂O₂ is a catalytic hydrogen wave, and the reduction wave enhanced by H₂O₂ is a so-called parallel catalytic hydrogen wave. The analytical sensitivity of the parallel catalytic hydrogen wave is ca. 60 times higher than that of the corresponding catalytic hydrogen wave. Based on the parallel catalytic hydrogen wave a novel method has been developed for determination of telmisartan by linear sweep polarography. The calibration curve is linear in the range 2.0×10^–8–2.0×10^–6 mol L^–1 and the detection limit is 1.0×10^–8 mol L^–1. The precision is excellent with relative standard deviations of 2.6% at a concentration of 1.0×10^–7 mol L^–1 telmisartan. The proposed method has been applied to the direct determination of the telmisartan in capsule forms and biological samples. The proposed method has been proved to be advantageous over existing CZE and MEKC methods in simplicity, rapidity, and reproducibility.     

Determination of potassium in sea-water by capillary isotachophoresis

Summary A new analytical procedure for the determination of potassium in sea-water was developed using capillary isotachophoresis and ion-exchange. After the sea-water sample was passed through the column packed with an ammonium form cation-exchange resin, sodium ion was removed with 2×10^–2 mol/l ammonium chloride solution and then potassium ion was eluted with 3×10^–1 mol/l ammonium chloride solution. Simultaneous determination of potassium and sodium ions was performed with a newly developed electrolyte system; the leading electrolyte was 5 mmol/l cesium hydroxide containing 2 mmol/l 18-crown-6, 0.01% hydroxypropyl methylcellulose (HPMC) and 70% methanol; the terminating electrolyte was 5 mmol/l tetrabutylammonium bromide containing 0.01% HPMC and 70% methanol. A large amount of ammonium in the eluate did not interfere with the isotachophoretic measurement of potassium and sodium ions. A linear working curve was obtained for artificial sea-water samples containing up to 700 mg/l potassium ion. The proposed method was applied to the determination of potassium in surface and bottom sea-water samples.

---

Kaliumbestimmung in Meereswasser durch Capillar-Isotachophorese

     

Analysis of Zoledronic Acid and Its Related Substances by Ion-Pair RP-LC

A simple high-performance liquid chromatographic method – ion-pair reversed- phase high performance liquid chromatography (RPIC) has been developed and employed for the analysis of zoledronic acid and its related substances in bulk material and commercial dosage forms. The mobile phase was a mixture of methanol (20%) and 5 mmol L^–1 phosphate buffer (80%) containing 6 mmol L^–1 tetrabutylammonium bromide, adjusted to pH 7.0 with sodium hydroxide. C₈ column was used as the stationary phase. The chromatographic conditions were optimized. The active ingredient – zoledronic acid was successfully separated from its related substances, including remained imidazol-1-yiacetic acid in the synthesis of zoledronic acid and other possible impurities of oxidation and decomposition. The excipients did not interfere with the determination of zoledronic acid in commercial dosage formulations. The method was rapid, simple, accurate and reproducible. It was not only successfully employed for the assay of zoledronic acid in bulk material and pharmaceutical dosage forms but also for the determination of its related substances.     

Determination of rofecoxib,in the presence of its photodegradation product,in pharmaceutical preparations by micellar electrokinetic capillary chromatography

A simple and rapid micellar electrokinetic capillary chromatographic (MEKC) method for analysis of rofecoxib (ROF) and its photodegradation product (PDP) in pharmaceutical preparations has been developed and validated. Analyses were conducted in a fused silica capillary (72 cm effective length, 50 m i.d.) with a background electrolyte consisting of 25 mmol L^–1 borate buffer at pH 7.0 containing 15 mmol L^–1 sodium dodecyl sulfate (SDS) and 10% acetonitrile (ACN). The separation was performed by voltage-controlled system, applying 30 kV at 30 °C, detecting at 225 nm; injection was hydrodynamic at 50 mbar for 2 s. Nifedipine was used as internal standard (IS). Under the optimum conditions ROF, PDP, and IS were well separated with in 10 min. The method was validated with regard to linearity, limit of detection and quantitation, precision, accuracy, specificity, and robustness. The detection limit of the method was low, 0.8 g mL^–1, and the linearity range was wide, 2.5 to 125 g mL^–1. The method was highly efficient—5×10⁵ plates m^–1 for ROF. The method was applied to the tablet form of ROF-containing pharmaceutical preparations. The data were compared with those from the voltammetric method described in literature. No statistically significant difference was found.     

Highly Sensitive Spectrofluorimetric Determination of Trace Amounts of Indium with 5-Bromine-Salicylaldehyde Salicyloylhygrazone

The fluorescence reaction of 5-bromine-salicylaldehyde salicyloylhydrazone (5-Br-SASH) with indium was studied in detail. Based on this chelating reaction, a sensitive spectrofluorimetric method was developed for the determination of indium in a water–ethanol (63%) medium at PH 4.6. Under these conditions, the In-5-Br-SASH complex has excitation and emission maxima at 395 nm and 461 nm, respectively. The linear range of the method is from 0 to 1000 ng mL^–1and the detection limit is 2.4 ng mL^–1of indium. The molar ratio of indium to the reagent is 1 : 3. Interferences from other ions were studied. The method was successfully applied to the determination of indium in lead, tin, spelter, zinc sulfide using the standard additions method.     

Square-wave voltammetric determination of cefoperazone in a bacterial culture,pharmaceutical drug,milk, and urine

Use of square-wave voltammetry (SWV) for determination of cefoperazone (CFPZ) in some buffers, bacterial culture, urine, and milk is described. CFPZ provides a specific voltammetric signal which is affected by pH and solution components. Determination of CFPZ in Britton–Robinson buffer, pH 4.4, is sensitive with a low detection limit (about 0.5 nmol L^–1). In a more complex medium (bacterial 2YT medium, pH 7.2) the detection limit was approximately 1.5 mol L^–1. We provide evidence that SWV is a suitable and quick method for CFPZ determination in a culture of living bacteria without separation of biomass. We have found big differences between methicillin-resistant Staphylococcus aureus (MRSA) and methicillin-sensitive Staphylococcus aureus (MSSA) in cultivation in the presence of CFPZ, depending on time. When CFPZ is cleaved by penicillinase, a new SWV peak b appears at more positive potentials. This peak rises both with increasing concentration of enzyme and with cleavage time while the original CFPZ peak is simultaneously decreasing. We determined the concentration of CFPZ in the drug Pathozone by the standard addition method and achieved good agreement with the declared value of CFPZ in the drug. With a simple pretreatment procedure it is possible to determine CFPZ in milk; for urine no pretreatment was required. Using SWV we could detect CFPZ concentrations as low as 500 nmol L^–1 in bovine milk and human urine.     

Spectrophotometric determination of manganese with derivatives of 1,3,3-trimethyl-2-[3-(1,3,3-trimethyl-1,3- H-indol-2-ylidene)propenyl]-3 H-indolium

A new, simple, rapid, and sensitive spectrophotometric method has been developed for the determination of manganese in sewage. The method is based on the reaction of manganese with derivatives of 1,3,3-trimethyl-2-[3-(1,3,3-trimethyl-1,3-H-indol-2-ylidene)propenyl]-3H-indolium to form a colored ion associate with a sensitive absorption maximum at 560 nm. The appropriate reaction conditions have been established: pH 8.5–10.0, 1.25–2.3×10^–3 mol L^–1 1-nitroso-2-naphthol, and 1.6–2.4×10^–4 mol L^–1 dye reagent. Beer's law is obeyed for manganese concentrations up to 4.2 mg L^–1. The limit of detection is 0.01 mg L^–1 Mn²⁺; the molar absorptivity of the ion associate was 7.5×10⁴ L mol^–1 cm^–1. The effect of various foreign ions was examined. A reaction mechanism is suggested. The developed procedure was tested for determination of manganese in sewage with satisfactory precision and accuracy.     

Simultaneous Determination of Trimethoprim, Sulfadiazine, Florfenicol and Oxolinic Acid in Surface Water by Liquid Chromatography Tandem Mass Spectrometry

A liquid chromatographic/tandem mass spectrometric method using atmospheric pressure chemical ionisation (LC-APCI-MS-MS) was developed for simultaneous determination of trimethoprim, sulfadiazine, florfenicol and oxolinic acid in surface water. The compounds were extracted by solid phase extraction on a polymeric sorbent. Two transition products were monitored for each compound. The detection capabilities related to the transition products of lowest abundance were 1 ng L^–1 for trimethoprim, sulfadiazine and florfenicol and 2 ng L^–1 for oxolinic acid. The mean recoveries were 84%, 83%, 96% and 78% at a level of 10 ng L^–1. The relative repeatability standard deviations were less than 11% at a level of 10 ng L^–1.     

Simple and sensitive assay for nucleic acids by use of the resonance light-scattering technique with copper phthalocyanine tetrasulfonic acid in the presence of cetyltrimethylammonium bromide

On the basis of enhancement of resonance light scattering (RLS) of copper phthalocyanine tetrasulfonic acid (CuTSPc) by nucleic acids and cetyltrimethylammonium bromide (CTMAB) under suitable conditions, a new RLS method for determination of nucleic acids in aqueous solutions has been developed. At pH 9.80–10.95 and ionic strength 0.01 mol L^–1 (NaCl), the interaction of copper phthalocyanine tetrasulfonic acid with nucleic acids in the presence of cetyltrimethylammonium bromide results in enhanced RLS signals at 282.0 nm, 383.6 nm, and 616.2 nm in the enhanced regions. It was found that the enhanced RLS intensity at 383.6 nm was proportional to the concentration of nucleic acids within suitable ranges. The limits of detection were 10.6 ng mL^–1 for fish sperm DNA and 32.4 ng mL^–1 for calf thymus DNA when the concentration of copper phthalocyanine tetrasulfonic acid was 2.0×10^–6 mol L^–1. This method is rapid, simple and sensitive. In addition, the reagents used are relatively inexpensive, stable, and easily synthesised. The method can be applied to the determination of nucleic acids in the presence of coexisting substances, and we have applied it to the determination of DNA in synthetic samples, with satisfactory results.     

Separation of traces of heavy metals from an iron matrix by use of an emulsion liquid membrane

An emulsion liquid membrane method has been developed for separating traces of heavy metals from an iron matrix. A 1.0-mL volume of aqueous iron(III) solution (pH 2.0) was emulsified with a mixture of 0.6 mL toluene, 2.4 mL n -heptane, and 80 mg sorbitan monooleate (Span-80). The resulting water-in-oil type emulsion was gradually injected into 25 mL of 1.5 mol L^–1 hydrochloric acid solution containing 30 mmol L^–1 8-quinolinol and 1.0 mol L^–1 of ammonium sulfate and was dispersed as numerous tiny globules by stirring for 40 min. More than 90% of the iron(III) diffused through the oil layer to the external hydrochloric acid solution with the aid of complexation with 8-quinolinol, whereas trace heavy metals, e.g. Cr(III), Mn(II), Co(II), Ni(II), Cu(II), and Pb(II), remained quantitatively in the internal aqueous phase. After collecting the dispersed emulsion globules, they were demulsified and trace metals in the segregated aqueous phase were determined by graphite-furnace atomic absorption spectrometry. Owing to sufficient removal of the iron matrix trace metal impurities in high-purity iron were successfully determined without interference, as was confirmed by analysis of certified reference materials.     

Determination of Ca, K, Mg, Na, sulfate, phosphate, formate, acetate, propionate, and glycerol in biodiesel by capillary electrophoresis with capacitively coupled contactless conductivity detection

In this work, a new method employing capillary electrophoresis (CE) for the determination of several species in biodiesel is introduced. The concentrations of inorganic species (Na⁺, K⁺, Ca²⁺, Mg²⁺, SO₄²⁻, and PO₄³⁻) and glycerol are of interest to the regulatory authorities due to their ability to form undesirable compounds in engines. Additionally, other species of low molecular weight (e.g., acetate, formate, and propionate) are of interest because they contribute towards increasing the acidity. These species are formed by the degradation of biodiesel and cause damage to engines and the environment. The cation separation was performed in background electrolyte (BGE) composed of 30 mmol L⁻¹ of 2-(n-morpholino)ethanesulfonic acid (MES)/L-histidine (His), pH 6. The separation of anionic species was carried out in similar BGE with 0.2 mmol L⁻¹ cetyltrimethylammonium bromide (CTAB) added. For glycerol, a neutral species, its oxidation with periodate was employed. This well-known reaction is specific to polyols and generates iodate. The amount of iodate produced by the reaction was determined by CE. The separation was carried out in approximately 1 min using BGE composed of 30 mmol L⁻¹ acetic acid, pH 3. The analytical parameters evaluated were: linearity (r > 0.99), the RSD values for area and migration time were < 3.4% and 0.9%, respectively, and recovery was in the range of 89 to 107%.     

Voltammetric study of glibenclamide at carbon paste and Sephadex-modified carbon paste electrodes

The oxidative behaviour of the antidiabetic agent glibenclamide on a bare carbon paste electrode (CPE) and a Sephadex-modified carbon paste electrode (SMCPE) was explored by cyclic and differential pulse voltammetry (DPV). The analysis procedure consisted of an open circuit accumulation step in stirred sample solution of Britton-Robinson buffer (0.04 mol L^–1, pH 2.0). This was followed by medium exchange to a clean solution of Britton-Robinson buffer (0.04 mol L^–1, pH 5.0), and subsequently an anodic potential scan was effected to obtain the voltammetric peak. The glibenclamide oxidation peak current obtained by DPV was proportional to the concentration of the glibenclamide in the range of 1.0×10^–9 mol L^–1 to 5.0×10^–8 mol L^–1 for 180 s accumulation time, with a detection limit of 4.0×10^–10 mol L^–1. A method was developed for the determination of glibenclamide in formulation and spiked human serum. Moreover, the proposed procedure was used to estimate the serum concentrations after oral administration of a 5 mg tablet of glibenclamide to three diabetic subjects.     

Mercury-free sono-electroanalytical detection of lead in human blood by use of bismuth-film-modified boron-doped diamond electrodes

We report the electroanalytical determination of lead by anodic stripping voltammetry at in-situ-formed, bismuth-film-modified, boron-doped diamond electrodes. Detection limits in 0.1 mol L^–1 nitric acid solution of 9.6x10^–8 mol L^–1 (0.2 ppb) and 1.1x10^–8 mol L^–1 (2.3 ppb) were obtained after 60 and 300 s deposition times, respectively. An acoustically assisted deposition procedure was also investigated and found to result in improved limits of detection of 2.6×10^–8 mol L^–1 (5.4 ppb) and 8.5×10^–10 mol L^–1 (0.18 ppb) for 60 and 300 s accumulation times, respectively. Furthermore, the sensitivity obtained under quiescent and insonated conditions increased from 5.5 (quiescent) to 76.7 A mol^–1 L (insonated) for 60 s accumulation and from 25.8 (quiescent) to 317.6 A mol^–1 L (insonated) for 300 s accumulation. Investigation of the use of ultrasound with diluted blood revealed detection limits of the order of 10^–8 mol L^–1 were achievable with excellent inter- and intra-reproducibility and sensitivity of 411.9 A mol^–1 L . For the first time, electroanalytical detection of lead in diluted blood is shown to be possible by use of insonated in-situ-formed bismuth-film-modified boron-doped diamond electrodes. This method is a rapid, sensitive, and non-toxic means of clinical sensing of lead in whole human blood.     

Enhancing effect of DNA on chemiluminescence from the decomposition of hydrogen peroxide catalyzed by copper(II)

In the absence of any special luminescence reagent, emission of weak chemiluminescence has been observed during the decomposition of hydrogen peroxide catalyzed by copper(II) in basic aqueous solution. The intensity of the chemiluminescence was greatly enhanced by addition of DNA and was strongly dependent on DNA concentration. Based on these phenomena, a flow-injection chemiluminescence method was established for determination of DNA. The chemiluminescence intensity was linear with DNA concentration in the range 2×10^–7–1×10^–5 g L^–1 and the detection limit was 4.1×10^–8 g L^–1 (S/N=3). The relative standard deviation was less than 3.0% for 4×10^–7 g L^–1 DNA (n=11). The proposed method was satisfactorily applied for determination of DNA in synthetic samples. The possible mechanism of the CL reaction is discussed.     

Determination of uric acid in human saliva by capillary electrophoresis with electrochemical detection: potential application in fast diagnosis of gout

The clinical manifestations of gout result from the formation and deposition of uric acid (UA) crystals. The monitoring of UA level in less invasive biological samples such as saliva is suggested for diagnosis and therapy of gout, hyperuricemia and the Lesch–Nyhan syndrome. In order to investigate the correlation between trace amounts of UA in human saliva and urine and explore the potential application in fast diagnosis of gout, capillary electrophoresis with electrochemical detection (CE–ED) was applied for the determination of UA in human saliva and urine in this work. Under the optimum conditions, UA and three coexisting analytes could be well separated within 14 min at the separation voltage of 14 kV in 80 mmol L^–1 borax running buffer (pH 7.8). A good linear relationship was established between peak current and concentration of analytes over two orders of magnitude with detection limits (S/N=3) ranging from 1.09×10^–7 to 5.0×10^–7 mol L^–1 for all analytes. This proposed method has been successfully applied for study of the correlation between the UA content of human saliva and urine, providing an alternative and convenient method for rapid diagnosis of gout.