渐变折射率Ta_2O_5/SiO_2薄膜多脉冲激光损伤特性

采用离子束溅射(IBS)的方式,制备了1064nm高反射Ta2O5/SiO2渐变折射率光学薄膜。对其光学性能和在基频多脉冲下抗损伤性能进行了分析。通过渐变折射率的设计方式,很好地抑制了边带波纹,增加了1064nm反射率。通过对损伤阈值的分析发现,随着脉冲个数的增加,损伤阈值下降明显;但是在20个脉冲数后,损伤阈值(维持在22J/cm2左右)几乎保持不变直到100个脉冲数。通过Leica显微镜对损伤形貌的观察,发现损伤诱因是薄膜表面的节瘤缺陷。通过扫描电镜(SEM)以及聚集离子束(FIB)对薄膜表面以及断面的观察,证实了薄膜的损伤起源于薄膜表面的节瘤缺陷。进一步研究得出,渐变折射率薄膜在基频光单脉冲下损伤主要是由初始节瘤缺陷引起的,在后续多脉冲激光辐照下初始节瘤缺陷引起烧蚀坑的面积扩大扫过薄膜上的其他节瘤缺陷,引起了其他节瘤缺陷的喷射使损伤加剧,造成损伤的"累积效应"。     

Influence of overcoat on laser-induced damage threshold of 532 and 800 nm TiO2/SiO2 high reflectors

TiO₂/SiO₂ high reflectors with and without a SiO₂ overcoat are deposited by electron-beam evaporation. The film properties are characterized by visible spectrometry measures, structure analysis, roughness and laser-induced damage threshold (LIDT) tests, surface defects and damage morphology observation. The effects of overcoats on LIDT at 532 nm, 8 ns and 800 nm, 220 ps laser pulses are investigated. The relations between film structure, roughness, surface defects, electric field and LIDT are discussed. It is found that overcoats can increase the LIDT at these two laser wavelengths. The reduction of peak temperature, the low defects density and roughness, the low intrinsic absorption of SiO₂ and its amorphous structure are the main reasons for LIDT improvement by overcoats.     

Effects of annealing on laser-induced damage threshold of TiO2/SiO2 high reflectors

The mechanism of improving 1064 nm, 12 ns laser-induced damage threshold (LIDT) of TiO₂/SiO₂ high reflectors (HR) prepared by electronic beam evaporation from 5.1 to 13.1 J/cm² by thermal annealing is discussed. Through optical properties, structure and chemical composition analysis, it is found that the reduced atomic non-stoichiometric defects are the main reason of absorption decrease and LIDT rise after annealing. A remarkable increase of LIDT is found at 300 °C annealing. The refractive index and film inhomogeneity rise, physical thickness decrease, and film stress changes from compress stress to tensile stress due to the structure change during annealing.     

Effect of Process Parameters on Laser Damage Threshold of TiO2 Coatings

We investigate the laser damage behaviour of an electron-beam-deposited TiO2 monolayer at different process parameters. The optical properties, chemical composition, surface defects, absorption and laser-induced damage threshold （LIDT） of films are measured. It is found that TiO2 films with the minimum absorption and the highest LIDT can be fabricated using a TiO2 starting material after annealing. LIDT is mainly related to absorption and is influenced by the non-stoichiometric defects for TiO2 films. Surface defects show no evident effects on LIDT in this experiment.     

Investigation of annealing effects on the laser-induced damage threshold of amorphous Ta2O5 films

Ta₂O₅ films were deposited using the conventional electron beam evaporation method and then annealed at temperatures in the range 373-673 K. Chemical composition, scattering and absorption were examined by X-ray photoelectron spectroscopy (XPS), total integrated scattering (TIS) measurement and the surface thermal lensing (STL) technique, respectively. The laser-induced damage threshold (LIDT) was assessed using the output from an Nd:YAG laser with a pulse length of 12 ns. The results showed that the improvement of the LIDT after annealing was due to the reduced substoichiometric and structural defects present in the film. The LIDT increased slightly below 573 K and then increased significantly with increase in annealing temperature, which could be attributed to different dominant defects. Moreover, the root mean square (RMS) roughness and scattering had little effect on the LIDT, while the absorption and the LIDT were in accord with a general relation.     

Effect of SiO2 protective layer on the femtosecond laser-induced damage of HfO2/SiO2 multilayer high-reflective coatings

Two kinds of HfO₂/SiO₂ 800 nm high-reflective (HR) coatings, with and without SiO₂ protective layer were deposited by electron beam evaporation. Laser-induced damage thresholds (LIDT) were measured for all samples with femtosecond laser pulses. The surface morphologies and the depth information of all samples were observed by Leica optical microscopy and WYKO surface profiler, respectively. It is found that SiO₂ protective layer had no positive effect on improving the LIDT of HR coating. A simple model including the conduction band electron production via multiphoton ionization and impact ionization is used to explain this phenomenon. Theoretical calculations show that the damage occurs first in the SiO₂ protective layer for HfO₂/SiO₂ HR coating with SiO₂ protective layer. The relation of LIDT for two kinds of HfO₂/SiO₂ HR coatings in calculation agrees with the experiment result.     

Influence of substoichiometer on the laser-induced damage characters of HfO2 thin films

HfO₂ is one of the most important high refractive index materials for depositing high power optical mirrors. In this research, HfO₂ thin films were prepared by dual-ion beam reactive sputtering method, and the laser-induced damage thresholds (LIDT) of the sample were measured in 1-on-1 mode for laser with 1064 nm wavelength. The results indicate that the LIDT of the as-grown sample is only 3.96 J/cm², but it is increased to 8.98 J/cm² after annealing under temperature of 200 °C in atmosphere. By measuring the laser weak absorption and SIMS of the samples, we deduced that substoichiometer is the main reason for the low LIDT of the as-grown sample, and the experiment results were well explained with the theory of electronic-avalanche ionization.     

The effect of porosity on the laser induced damage threshold of TiO2 and ZrO2 single layer films

Monolayer ZrO₂ and TiO₂ films were prepared on BK7 glass by physical vapor deposition (PVD) and were subsequently annealed for 1 h at 300 °C. By using the transmission spectra of two samples and the envelope method, the refractive index dispersion and extinction coefficients have been calculated. Laser induced damage threshold (LIDT) measurement shows that despite slight differences between the extinction coefficients of the two samples, the LIDT parameter of the ZrO₂ film is greater than that of the TiO₂ film. This fact leads us to consider thermal conductivity as an important parameter for interpreting the LIDT difference. According to our theoretical analysis, as a consequence of increase in the number of thermal barriers along poorer film, its thermal conductivity, and hence LIDT, decreased, which is in agreement with our experimental results. The measured porosity of the two samples shows higher porosity for TiO₂ single layer, which is in agreement with atomic force (AFM) images. The gradual and smooth damage morphology of ZrO₂ observed in optical images implies higher thermal conductivity than TiO₂.     

溶胶-凝胶ZrO2-TiO2高折射率光学膜层的抗激光损伤性能研究

采用溶胶-凝胶方法制备了ZrO₂-TiO₂(Ti含量为0—100mol%)高折射率光学薄膜. 借助激光动态光散射技术研究溶胶微结构. 采用傅里叶变换红外光谱、原子力显微镜、薄膜光学常数分析仪、漫反射吸收光谱及强激光辐照实验，对膜层的结构、光学性能及抗激光损伤性能进行了系统表征. 结果显示，溶胶-凝胶工艺可以在部分牺牲折射率的情况下，使膜层的抗激光损伤性能得到大幅度提升. 随Ti含量从0mol%增加至100mol%，膜层的平均损伤阈值呈下降趋势，当Ti含量从0mol%增加至60mol%时，平均损伤阈值从57.1J/cm²下降到21.1J/cm²(辐照激光波长为1053nm，脉冲宽度为10ns，“R/1”测试模式)，当Ti含量从60mol%增加至100mol%时，平均损伤阈值变化很小. 综合溶胶微结构、膜层光学性能和损伤实验结果可以推断，强激光诱导多光子吸收是引起膜层损伤的主要原因. 不同配比的复合膜之间光学带隙的显著差异导致相同辐照激光情况下多光子吸收的概率发生变化，从而导致损伤阈值的规律性变化. 关键词： 2-TiO₂薄膜')" href="#">ZrO₂-TiO₂薄膜 溶胶-凝胶 激光诱导损伤 光学带隙     

Detection and characterization of absorption heterogeneities in KH2PO4 crystals

The SOCRATE facility is used for the detection of heterogeneous absorption in large and rapidly grown KH₂PO₄ (KDP) crystals. The different regions are subsequently characterized by spectrophotometry and laser-damage measurement. In accordance with previous results from the literature we found that, by using the SOCRATE damage measurement set-up with a large beam (300 ∗ 600 μm²), the absorption level does not play a major role in the damage mechanism at 355 nm. However, by testing the damage resistance of the same KDP component with a focused beam (9 μm diameter) at 355 nm, we highlight for the first time significantly different damage resistances between highly and weakly absorbing regions from a KDP crystal. Indeed, with a focused beam, we demonstrate that the laser-damage threshold may be lower in some sectors cut in the pyramidal part than in sectors from the prismatic part. This means that the absorbing defects at high concentration are not the predominant damage precursors at 355 nm.     

Calculation of temperature fields with a film-substrate interfacial layer model to discuss the layer-pair number effects on the damage thresholds of LaF3/MgF2 high reflectors at 355 nm

Laser induced damage thresholds (LIDT) of LaF₃/MgF₂ high reflectors at 355 nm were measured and investigated as a function of layer-pair number. Generally, LaF₃/MgF₂ coatings with more layer pairs possessed higher LIDT, but coatings with too high layer-pair number crazed because of high tensile stress, so the LIDT of them decreased badly. The temperature rise in the coatings was calculated based on a film-substrate interfacial absorption model, and the depth of the damage in the coatings were measured by a Veeco optical profilograph. The two characterization methods together were used to interpret the effects of layer-pair number on LIDT, and the damage mechanism of coatings at laser wavelength of 355 nm was also discussed.     

Y2O3 stabilized ZrO2 thin films deposited by electron beam evaporation: Structural, morphological characterization and laser induced damage threshold

Four kinds of Y₂O₃ stabilized ZrO₂ (YSZ) thin films with different Y₂O₃ content have been prepared on BK7 substrates by electron-beam evaporation method. Structural properties and surface morphology of thin films were investigated by X-ray diffraction (XRD) spectra and scanning probe microscope. Laser induced damage threshold (LIDT) was determined. It was found that crystalline phase and microstructure of YSZ thin films was dependent on Y₂O₃ molar content. YSZ thin films changed from monoclinic phase to high temperature phase (tetragonal and cubic) with the increase of Y₂O₃ content. The LIDT of stabilized thin film is more than that of unstabilized thin films. The reason is that ZrO₂ material undergoes phase transition during the course of e-beam evaporation resulting in more numbers of defects compared to that of YSZ thin films. These defects act as absorptive center and the original breakdown points.     

Preparation of sol-gel ZrO2-SiO2 highly reflective multilayer films and laser-induced damage threshold characteristic

Sol-gel (ZrO₂/SiO₂)¹² ZrO₂ films were prepared by spin coating method. The reflectivity spectrum of the films was measured with a Lambda 900 spectrometer. In order to investigate laser-induced damage threshold (LIDT) characteristic of highly reflective films, one-layer ZrO₂ and SiO₂ films, two-layer ZrO₂/SiO₂ and SiO₂/ZrO₂ films were also prepared by spin coating method. LIDT of each film was measured. Damage morphology after laser irradiation was characterized by optical microscopy (Nikon E600K). The experimental results showed that the reflectivity of (ZrO₂/SiO₂)¹² ZrO₂ film at 1064 nm and 355 nm wavelength is 99.7%. The LIDT results decreases as the number of layer of films increases. All the films have similar damage morphology. The experimental results are explained by the different temperature profiles of the films.     

Effects of deposition parameters on laser-induced damage threshold of Ta2O5 films

Ta₂O₅ films were deposited on BK7 substrates by e-beam evaporation with different deposition parameters such as substrate temperature (323-623 K), oxygen pressure (0.5-3.0×10⁻² Pa) and deposition rate (0.2-0.5 nm/s). Absorption, scattering and chemical composition were investigated by surface thermal lensing (STL) technique, total integrated scattering (TIS) measurement and X-ray photoelectron spectroscopy (XPS), respectively. The laser-induced damage threshold (LIDT) was assessed using pulsed Nd:YAG 1064 nm laser at a pulse length of 12 ns. The results showed that optical properties, absorption and LIDT were influenced by the deposition parameters and annealing. However, scattering was little correlated with the deposition parameters. On the whole, the LIDT increased with increasing substrate temperature and oxygen pressure, whereas it increased firstly and then decreased upon increasing deposition rate. After annealing at 673 K for 12 h, the LIDT of films improved significantly. The dependence of possible damage mechanism on deposition parameters was discussed.     

Electron beam evaporated LaF3 thin films prepared by different temperatures and deposition rates

LaF₃ thin films were prepared by electron beam evaporation with different temperatures and deposition rates. Microstructure properties including crystalline structure and surface roughness were investigated by X-ray diffraction (XRD) and optical profilograph. X-ray photoelectron spectroscopy (XPS) was employed to study the chemical composition of the films. Optical properties (transmittance and refractive index) and laser induce damage threshold (LIDT) at 355 nm of the films were also characterized. The effects of deposition rate and substrate temperature on microstructure, optical properties and LIDT of LaF₃ thin films were discussed, respectively.     

等离子体氧轰击硅生成缺陷的研究

本文对等离子体氧轰击硅产生的缺陷进行了研究。发现等离子体氧轰击在硅中引入两个缺陷E₁(E_c—0.46eV)及E₂(E_c—0.04eV)。测量了缺陷的光电离截面谱,分析表明,缺陷E₂的电子声子相互作用很强,其Frank-Condon移动达0.76eV,缺陷E₁的电子声子相互作用较小,其Frank-Condon移动为0.04eV。由实验结果得到与缺陷E₁、E₂相耦合的声子模分别为hω_p⁽¹⁾=28meV,hω_p⁽²⁾=20meV。 关键词：     

Phonon modes in KH2PO3-type crystals

New infrared reflectivity spectroscopic measurements for polarization of the electric field perpendicular to the ferroelectric axis of KDP in its ferroelectric phase at 7K, are presented and discussed. The optical mode parameters of modes belonging to B₁ and B₂ symmetry are deduced from the experimental infrared reflectivity, together with the fractional number of dipoles pointing in the + c direction.     

Comparison of TiO2 and ZrO2 Films Deposited by Electron-Beam Evaporation and by Sol-Gel Process

TiO2 and ZrO2 films are deposited by electron-beam （EB） evaporation and by sol-gel process. The film properties are characterized by visible and Fourier-transform infrared spectrometry, x-ray diffraction analysis, surface roughness measure, absorption and laser-induced damage threshold （LIDT） test. It is found that the sol-gel films have lower refractive index, packing density and roughness than EB deposited films due to their amorphous structure and high OH group concentration in the film. The high LIDT of sol-gel films is mainly due to their amorphous and porous structure, and low absorption. LIDT of EB deposited film is considerably affected by defects in the film, and LIDT of sol-gel deposited film is mainly effected by residual organic impurities and solvent trapped in the film.     

Linear and nonlinear optical properties of dye-doped KDP crystals: Effect of thermal treatment

Potassium dihydrogen phosphate crystals (KDP, KH₂PO₄) doped with the organic xylenol orange (XO) dye are grown, the XO concentration in the crystal matrix is about 10 ppm. The spectral and luminescent properties of nominally pure, dye-doped and dye-doped/annealed at 150 °C crystals (KDP, KDP:XO and KDP:XO_an) were measured. The annealing temperature effect on the degree of dye protonation in the crystal matrix is established. Analysis of the IR-absorption spectra reveals a strong interaction between the incorporated dye molecules and the hydrogen subsystem of the matrix. The nonlinear optical (NLO) properties of KDP, KDP:XO and KDP:XO_an crystals are studied within the self-action effect of picosecond laser pulses at 532 nm. The mechanism of photoinduced bleaching and the effects of laser beam self-focusing (in KDP) and self-defocusing (in KDP:XO and KDP:XO_an) are supposed to be due to resonance excitation of the subsystems of intrinsic defects and dye molecules, correspondingly. For KDP:XO_an it is shown that thermal annealing of intrinsic crystal defects leads to domination of more effective NLO response of the subsystem of dye molecules that is correlated with photoluminescence data.     

Working Pressure Dependence of Properties of Al2O3 Thin Films Prepared by Electron Beam Evaporation

The effects of working pressure on properties of Al2O3 thin films are investigated. Transmittance of the Al2O3 thin film is measured by a Lambda 900 spectrometer. Laser-induced damage threshold （LIDT） is measured by a Nd：YAG laser at 355 nm with a pulse width of 7ns. Microdefects were observed under a Nomarski microscope. The samples are characterized by optical properties and defect, as well as LIDT under the 355 nm Nd：YAG laser radiation. It is found that the working pressure has fundamental effect on the LIDT. It is the absorption rather than the microdefect that plays an important role on the LIDT of Al2O3 thin film.