High repetition rate mid-infrared generation with singly resonant optical parametric oscillator using multi-grating periodically poled MgO:LiNbO3

A high repetition rate mid-infrared singly resonant optical parametric oscillator (OPO) using MgO-doped multi-grating periodically poled LiNbO₃ (MgO:PPLN) is demonstrated. A 1064 nm Q-switched Nd:YVO₄ laser at 10 kHz repetition rate and pulse width of 17.8 ns was used to pump the OPO. The period of the quasi-phase matched (QPM) grating in the multi-grating MgO:PPLN chip varied from 25.5 to 31.5 μm in steps of 0.5 μm. This corresponds to the generation of a signal beam from 1.37 to 1.64 μm and an idler beam from 3.0 to 4.8 μm, respectively. A maximum signal power of 250 mW and idler power of 140 mW has been obtained with an input pump beam of power 1.92 W, for a grating period of 30.5 μm. A maximum optic-optic conversion efficiency of 20% and 7.4% in the idler has been observed. It has been observed that the output power increases as the period of the grating increases.     

Widely tunable, high-repetition-rate, dual signal-wave optical parametric oscillator by using two periodically poled crystals

This paper reports on a high-repetition-rate dual signal-wave (DSW) optical parametric oscillator (OPO) operating at the 1.5 μm band with tunable wavelength intervals from 2.5 nm to 69.1 nm. Two periodically poled crystals, a periodically poled lithium niobate (PPLN) with multiple gratings and a single grating MgO-doped PPLN (PPMgOLN), are cascaded in the same OPO cavity to generate dual signal-waves by using quasi-phase-matched (QPM) technique. The pump source was a Q-switched diode-pumped Nd:YVO₄ laser operating at 50 kHz. At an incident pump power of 3 W, an average output power of 169.6 mW at 1489.2 nm and 1558.3 nm has been achieved.     

High efficiency and high energy parametric wavelength conversion using a large aperture periodically poled MgO:LiNbO3

We have demonstrated an efficient high energy 2 μm laser generation with a 36 mm long large aperture 5 mol% MgO-doped periodically poled LiNbO₃ (PPMgLN) nonlinear optical crystal. A high power Q-switched Nd:YAG laser (1.064 μm) was used to pump the quasi-phase matched (QPM) optical parametric oscillator (OPO). A total output energy of 186 mJ with 58% slope efficiency was obtained in two separate beams at 2 μm.     

A High-Power,Long-Wavelength Infrared ZnGeP<Subscript>2</Subscript> Opo Pumped by a <Emphasis Type="Italic">Q</Emphasis>-Switched Tm,Ho:GdVO<Subscript>4</Subscript> Laser

We report a high-power, long-wavelength infrared ZnGeP₂ (ZGP) optical parametric oscillator (OPO) pumped by a Q-switched Tm,Ho:GdVO₄ laser. The wavelength tuning range of 7.8–9.9 μm is realized by rotating the external angle of the ZGP crystal. We obtain an output power over 30 mW across the whole wavelength range and achieve a 1.71 W output power at 8.08 μm by transmitting the OPO parameters, corresponding to an idler laser slope efficiency of 12.1%.     

Q-switched Nd lasers pumped directly into the F3/2 emitting level

The influence of the direct pumping into the ⁴F_3/2 emitting level on the output characteristics of continuous-wave (CW) pumped, passively or actively (acoustooptic, AO) Q-switched Nd lasers is discussed. In case of passive Q-switching by Cr⁴⁺:YAG saturable absorber (SA) crystal, the change of pumping wavelength from 0.81 μm into the highly-absorbing ⁴F_5/2 level to 0.88 μm into the ⁴F_3/2 level of Nd does not modify the energy of the Q-switch pulse, but increases the pulse repetition rate and the laser average power for the same absorbed pump power. This is demonstrated with 0.81 and 0.88 μm CW laser diode-pumped Nd:YAG and Nd-vanadate lasers with average output power in the watt-level range at 1.06 μm. The effect is explained by the control of passive Q-switching by the intracavity photon flux that is influenced by the pump wavelength and by the initial transmission of the SA crystal. On the other hand, it is discussed and experimentally proved that due to the possibility to control externally the frequency of switching, in case of the AO Q-switched Nd laser the change of the pump wavelength from 0.81 to 0.88 μm increases the pulse energy for a fixed frequency, leading to a corresponding increase of the average laser power.     

Silicon donor and Stokes terahertz lasers

Two types of lasers based on hydrogen-like impurity-related transitions in bulk silicon operate at frequencies between 1 and 7 THz (wavelength range of 50-230 μm). These lasers operate under mid-infrared optical pumping of n-doped silicon crystals at low temperatures (<30 K). Dipole-allowed optical transitions between particular excited states of group-V substitutional donors are utilized in the first type of terahertz silicon lasers. These lasers have a gain ∼1-3 cm⁻¹ above the laser thresholds (>1 kW cm⁻²) and provide 10 ps-1 μs pulses with a few mW output power on discrete lines. Raman-type Stokes stimulated emission in the range 4.6-5.8 THz has been observed from silicon crystals doped by antimony and phosphorus donors when optically excited by radiation from a tunable infrared free electron laser. The scattering occurs on the 1s(E)→1s(A₁) donor electronic transition accompanied by an emission of the intervalley transverse acoustic g-phonon. The Stokes lasing has a peak power of a few tenths of a mW and a pulse width of a few ns. The Raman optical gain is about 7.4 cm GW⁻¹ and the optical threshold intensity is ∼100 kW cm⁻².     

Electro-optic Q-switched intracavity optical parametric oscillator at 1.53 μm based on KTiOAsO4

An eye-safe, high peak power optical parameter oscillator (OPO) intracavity pumped by electro-optic Q-switched Nd:YAG laser is presented. This OPO is based on a 20 mm length KTiOAsO₄ crystal with non-critical phase matching (θ = 90°, ?=0°) cut. An aperture ∅3 mm acted as limiting diaphragm to get good beam quality of pumping laser. The output energy of 25 mJ at the signal wavelength 1.53 μm was obtained with repetition rate of 1 Hz. The highest peak power intensity was up to 88 MW/cm² with pulse width of 4 ns. Without diaphragm, the maximum output energy of 90 mJ was achieved with area of light spot (∅6 mm) four times larger, but the peak power intensity was lower.     

Diode-end-pumped linear-polarized single-frequency Tm:YAG laser at room temperature

By using two solid uncoated etalons, we present a diode-pumped linear-polarized single-frequency Tm:YAG laser operating at 2 μm. Placing one 0.1 mm F-P etalon at nearly Brewster angle in the cavity, the linear-polarization laser is achieved. The other 1 mm F-P etalon was turned in the range of very small angle, single-longitudinal-mode (SLM) could be obtained. The maximum output power of linear-polarized single-frequency laser of 60 mW is achieved at the wavelength of 2013 nm. The degree of the polarization is over 30 dB. Long-term frequency stability was also investigated, with the results of wavelength fluctuation about 2.55 × 10⁻¹³ m within 3 min and frequency change about 18.86 MHz, corresponding to a frequency stability of 1.27 × 10⁻⁷.     

Diode-pumped passively Q-switched Nd:LuxY1−xVO4 laser at 1.34 μm with two V:YAG saturable absorbers

Laser performance with the mixed Nd:Lu_0.15Y_0.85VO₄ crystal at 1.34 μm wavelength has been demonstrated. The continuous wave (cw) operation was carried out in a simple plano-concave resonator with an optical conversion efficiency of 23% and a slop efficiency of 25%. At a pump power of 6.78 W, the Q-switched pulses with the largest average output power of 349 mW, the shortest pulse width of 30.6 ns, the largest repetition rate of 42.5 kHz, the highest peak power of 268 W and the largest pulse energy of 8.2 μJ were obtained, corresponding to the V:YAG with initial transmission of 89%.     

Visible femtosecond pulses by second-harmonic generation of a cw mode-locked KTP optical parametric oscillator

Efficient generation of femtosecond pulses in the wavelength range from 520 to 675 nm by external frequency doubling the signal wave of a non-critically phase-matched picosecond KTP Optical Parametric Oscillator (OPO) in a non-critically phase-matched temperature tuned LiB₃O₅(LBO) crystal is demonstrated. An average power of the second harmonic as high as 310 mW at 575 nm was generated. In the absence of group velocity mismatch of LBO for a wavelength of the OPO at about 1.3 µm the minimum second-harmonic pulse width was 400 fs at 645 nm.     

Efficient 1.8 μm KTiOPO4 optical parametric oscillator pumped within an Nd:YAG/SrWO4 Raman laser

A 1.8?μm optical parametric oscillator (OPO) based on a noncritically phase-matched KTiOPO4 crystal is demonstrated. OPO and stimulated Raman scattering techniques are successfully combined in an acousto-optically Q-switched Nd:YAG/SrWO4 Raman laser. The device efficiently realizes three steps of conversion: from a laser diode wavelength of 808?nm to the fundamental wavelength of 1064?nm; next, to the Stokes wavelength of 1180?nm; and finally to the OPO signal wavelength of 1810?nm. With an incident diode power of 7.2?W and a pulse repetition rate of 15?kHz, an average signal power of 485?mW is obtained with a diode-to-signal conversion efficiency of 6.75%. The beam quality factors (M2) of the signal wave in both horizontal and vertical directions are measured to be 1.7±0.2. The numerical output power results of the system, the thermal lensing, and the stability parameter of the cavity are also discussed.     

Efficient Nd:YAG pumped mid-IR laser based on cascaded KTP and ZGP optical parametric oscillators and a ZGP parametric amplifier

Efficient conversion into the mid-IR of a low pulse-energy (2.5 mJ) Nd:YAG laser is achieved by cascaded KTiOPO₄ (KTP) and ZnGeP₂ (ZGP) optical parametric oscillators followed by a ZGP optical parametric amplifier. The first stage 2.13 μm degenerate KTP OPO uses four KTP crystals in a walk-off compensated geometry and an elliptical pump beam focal geometry to produce up to 2.2 W from 6.3 W incident. The 2.13 μm e-ray pumps a Type-I ZGP OPO, which produces 0.5 W of light in the 3.8-4.8 μm spectral region that in turn is amplified by a 2.13 μm o-ray pumped optical parametric amplifier generating 0.84 W with an M² of <2.     

Continuously wavelength-spacing-tunable and idler-output multiwavelength fiber optical parametric oscillator

We demonstrate a continuously wavelength-spacing-tunable and high-power multiwavelength fiber optical parametric oscillator based on the multiwavelength idler-output technique. The laser cavity for multiwavelength idler outputs is constructed by a pumped highly-nonlinear dispersion-shifted fiber as parametric gain medium, two highly-reflective chirped fiber Bragg gratings (CFBGs) and a superimposed CFBG as comb-like filter. At a pump power of 1.1 W, the idler output of 10 wavelengths around 1.56 μm is achieved with a wavelength spacing of 0.39 nm. The wavelength spacing can be continuously tuned from 0.39 to 1.0 nm by utilizing a cantilever beam-based chirp tuning method to change the FSR of the superimposed CFBG. Our experimental results show that the designed multiwavelength idler-output scheme can significantly increase the multiwavelength output power with a total output power of 98 mW and each idler-channel power of 16.3 mW.     

Broadband Er-Yb co-doped superfluorescent fiber source

In this paper, extensive experimental results on broad-band double cladding Er³⁺-Yb³⁺ co-doped superfluorescent fiber sources (SFSs), characterizing their output power, mean wavelength, and bandwidth (BW) stability with variations of pump power, pump wavelength, and fiber temperature, have been reported. For a 55-cm fiber, SFS power from 3.7755 (maximum BW condition of more than 80 nm) to 9.1837 mW (maximum power condition, BW is about 34 nm) has been achieved. The SFS mean wavelength dependence on pump wavelength is highly pump temperature sensitive, and can be reduced to zero in a chosen pump temperature field. The intrinsic variation of the SFS mean wavelength λ_m with fiber temperature is also measured, and a linear variation from 15 to 45 °C with a slop of −0.053 nm/°C for L_f = 100 cm and −0.04 nm/°C for L_f = 55 cm is found.     

High repetition rate Q-switched microchip Nd:YVO4 laser with pulse duration as short as 1.1 ns

We have demonstrated a compact and an efficient passively Q-switched microchip Nd:YVO₄ laser by using a composite semiconductor absorber as well as an output coupler. The composite semiconductor absorber was composed of an LT (low-temperature grown) In_0.25Ga_0.75As absorber and a pure GaAs absorber. To our knowledge, it was the first demonstration of the special absorber for Q-switching operation of microchip lasers. Laser pulses with durations of 1.1 ns were generated with a 350 μm thick laser crystal and the repetition rate of the pulses was as high as 4.6 MHz. The average output power was 120 mW at the pump power of 700 mW. Pulse duration can be varied from 1.1 to 15.7 ns by changing the cavity length from 0.45 to 5 mm. Pulses with duration of 1.67 and 2.41 ns were also obtained with a 0.7 mm thick laser crystal and a 1 mm thick laser crystal, respectively.     

Mid-infrared tunable dual-wavelength generation based on a quasi-phase-matched optical parametric oscillator

We report an efficient optical parametric oscillator (OPO) of dual idler wave output based on periodically poled MgO:LiNbO₃ with a periodically-phase-reversed grating structure, which is pumped by a Q-switched 1.064 μm laser with a repetition rate of 50 kHz. 0.98 W of dual idler-waves at 3.824 μm and 3.731 μm is achieved at room temperature, leading to a 12.9% conversion efficiency. The crystal temperature tuning provides output tunability of the dual idler wavelengths. In addition, the sum frequency generation of the dual signal waves is simultaneously observed in the OPO cavity.     

A photonic wire-based directional coupler based on SOI

A photonic wire-based directional coupler based on SOI was fabricated by e-beam lithography (EBL) and the inductively coupled plasma (ICP) etching method. The size of the sub-micron waveguide is 0.34 μm × 0.34 μm, and the length in the coupling region and the separation between the two parallel waveguides are 410 and 0.8 μm, respectively. The measurement results are in good agreement with the results simulated by 3D finite-difference time-domain method. The transmission power from two output ports changed reciprocally with about 23 nm wavelength spacing between the coupled and direct ports. The extinction ratio of the device was between 5 and 10 dB, and the insertion loss of the device in the wavelength range 1520-1610 nm was between 22 and 24 dB, which included an about 18.4 ± 0.4 dB coupling loss between the taper fibers and the polished sides of the device.     

High-power 1.5 and 3.4 μm intracavity KTA OPO driven by a diode-pumped Q-switched Nd:YAG laser

With a non-critically phase-matched KTA crystal, a high-power intracavity optical parametric oscillator (IOPO) driven by a diode-side-pumped acousto-optically Q-switched Nd:YAG laser has been realized. The maximum average output power of 13.6 W at the signal wavelength of 1534 nm and 3 W at the idler wavelength of 3472.7 nm were obtained with the repetition rate of 18 kHz, giving the optical-optical conversion efficiency of about 5.7% from diode-power at 808 nm to OPO signal output, which was the highest conversion efficiency for intracavity KTA OPO with diode-side-pumping configurations to our best knowledge. At the highest output power of 13.6 W, the signal pulse duration of 5.46 ns was obtained, corresponding to the single pulse energy of 756 μJ and peak power of 138 kW, respectively.     

Semiconductor optical amplifier based swept wavelength source at 1060 nm using a scanning Fabry-Perot filter and an YDFA-based booster amplifier

We demonstrate a tuneable laser operating in the 1-1.1 μm wavelength region with a tuning range of 43 nm (FWHM), an output power of 19 mW and coherence length of 14 mm. The source is based on a master laser consisting of a cavity tuned ring configuration with a fibre Fabry-Perot filter used as a tuning element and a semiconductor amplifier as gain medium. The output of the master laser is subsequently power boosted using an Ytterbium doped fibre amplifier (YDFA). In addition to providing a power boost, we demonstrate that by tailoring the gain spectrum of the YDFA it is possible to increase the FWHM scanning range by 7 nm compared to that of the master laser.     

Tunable terahertz generation from one CO2 laser in a GaSe crystal

Coherent terahertz pulses have been generated at a range of 236.3-1104.5 μm (0.27-1.3 THz) by one CO₂ laser with dual-wavelength output based on collinearly phase-matched different frequency generation (DFG) in a GaSe crystal. This source has the advantages of compact and simplicity for tuning. The output power of the THz pulse and phase-matching conditions were investigated. The maximum single pulse energy of 11 nJ was generated at a frequency of 1.23 THz (243.6 μm), corresponding to a peak output power 182 mW.