M(TNR)·H2O的热分解机理

本文用TG—DTA、DSC、IR和X光衍射分析考察了三硝基间苯二酚金属盐M(TNR)·H_2O(M=Pb、1/4Pb3/4Ba、Ba)的热行为及其热分解机理。结果表明,M(TNR)·H_2O晶体的热分解过程均分三个阶段进行。即脱水阶段;脱硝逸出NO_2伴随苯环碎裂成凝聚相产物的阶段和凝聚相产物分别生成PbO和少量碳;BaCO_3、PbO和少量碳;BaCO_3的阶段。     

硝酸盐热反应法制备Y-Ba-Cu-O系超导材料的反应条件与性能关系

本文用硝酸盐热反应法制备了Y-Ba-Cu-O系高Tc超导材料,并探讨了不同的制备条件对材料结构和性能的影响,确定了合适的制备条件,在此条件下,可制备出零电阻温度T_(R=0)=90K,转变温度T_0=93K的超导体材料,经X射线衍射物相分析表明以YBa_2Cu_3O_(6.5+δ)物相为主夹杂少量非超导相,制备过程的最高热处理温度较以氧化物和(或)碳酸盐为原料要低100℃左右.     

添加Cu2S对Bi-Pb-Sr-Ca-Cu-O体系超导性的影响

本文对Cu_2S添加的Bi-Pb-Sr-Ca-Cu-O体系进行了低温电阻、X射线衍射和XPS研究．实验结果表明，加入少量的Cu_2S能够降低高T_c相的形成温度，改善超导性能，加入Cu_2S引起了Cu 2p_(3/2)谱的主峰向低结合能方向移动，并减少其卫星峰的面积．这表明Cu_2S的加入减少了Cu~(2+)的量，即导致空穴载流子浓度的减小．     

用于X射线成像板的Ba_7F_(12)Cl_2:Eu~(2+)水热合成及其表征

X射线成像板的成像性能很大程度上取决于存储荧光粉材料的物理化学性能。本文采用水热制备方法,以BaCl2、EuBr2、NaBF4为反应原料,以乙二胺四乙酸(EDTA)为辅助剂制备了Ba7F12Cl2:Eu2+荧光粉。利用X射线粉末衍射(XRD)、场发射扫描电镜(SEM)、X射线能量损失谱(EDS)、拉曼光谱(Raman)、荧光光谱(PL)等对制备的Ba7F12Cl2:Eu2+进行了表征。根据反应条件对产物的影响,初步提出了产物的形成过程。结果表明:反应温度及EDTA用量对产物物相和形貌有显著影响;制备的Ba7F12Cl2:Eu2+荧光粉有较好的发光性能。     

过渡金属氢化物和聚集双键化合物反应的研究——Ⅴ.Cp_2MH_2(M=Zr,Hf)与RNCS(R=n-Bu,c-C_6H_(11),C_6H_5,2-C_(10)H_7)、CS_2的反应

本文研究了Cp_2ZrH_2与CS_2、RNCS(R=n-Bu,c-C_6H_11,C_6H_5,2-C_(10)H_7)和Cp_2HfH_2与c-C_6H_(11)NCS的反应,探讨了在这类新型脱硫反应中锆氢与铪氢配合物化学反应性能上的差异.从以上反应中分别得到两个硫桥同核双金属配合物(Cp_2MS)_2(1,M=Zr;2,M=Hf)和有机铪配合物Cp_2Hf[SC(H)NR]_2(3,R=c-C_6H_(11)).产物结构由元素分析、IR、~1H和~(13)C NMR及MS谱分析鉴定,产物1的晶体结构由X光四圆衍射方法测定,有机产物X=CH_2和CH_3X(H)(X=S,NR)由GC-MS谱分析测定.     

Nb_3X_4(X=S,Se,Te)的能带结构研究

固相过渡金属原子簇化合物Nb_3X_4(X=S,Se,Te)在低温下出现超导行为,且从S到Te,Nb_3X_4的超导转变温度Tc呈下降趋势。本文采用EHT近似下的紧束缚能带方法,计算了Nb_3X_4的能带结构。讨论其电子结构与超导电性的关系,并从化学键的观点出发对其Tc的递变加以解释。此外,本文还给出了Nb金属晶体的能带结构。     

超导相YBa_2Cu_3O_(7-d)的制备与结构研究

本文按计量式Y_(0.334)Ba_(0.666)CuO_(3-y)制备和得到了题目超导物相的样品。实验中使用柠檬酸为复合剂显著改善了金属氧化物的分散性和超导物相的均匀性。我们发现制备所得样品中,偏离四方晶格愈甚者,其超导性能愈佳。由X射线粉晶衍射数据测定了晶体结构,确认了金属离子的化学计量比和给出了氧原子的位置。正交或假四方晶胞的晶胞参数为a=3.893,b=3.813和c=11.867。晶胞由铜原子占据顶点位置的三个钙钛矿型立方体所组成,二个钡原子居于上层和底层的两个体心位置,而钇原子则占据居中立方体的体心位置。氧原子均占据诸立方体的稜心位置,但001/2处为空位,而01/20处的空位则导致晶格对称性由四方畸变为正交,这一畸变对超导相有深远的影响。钇和钡原子的配位多面体系由立方-八面体所派生的八配位和十配位的多面体,两者分别与移去晶胞中001/2和01/20处的氧原子后的氧多面体相对应。根据键价理论,以Y—O,Ba—O和Cu—O键长为基础,我们合理地论述了,即使在001/2及01/20处氧缺位的情况下,1/200处氧原子的占有率亦将低于1,与晶胞对应的该物相化学式为YBa_2Cu_bO_(7-d),0.2相似文献   

Li_3V_2(PO_4)_3制备及其电化学性能

应用碳包覆固相法合成锂离子电池Li3V2(PO4)3正极材料.X射线衍射、扫描电子显微镜表征材料的结构和观察表面形貌.材料的电阻和电化学性能测试表明,碳包覆Li3V2(PO4)3材料可避免颗粒团聚,减小颗粒尺寸,提高材料电导率,改善其电极的电化学性能.     

Gd—Ba—Cu氯氧化物新相

在探索高Tc超导材料的过程中,人们采用替换元素的方法,试图寻找新体系的高温超导体。例如用钇取代La-Ba-Cu-O体系中的镧,结果使新体系的Tc(ρ=0)由原体系的30K提高到90K;在Y-Ba-Cu-O体系中掺入适量的氯后,观察到155K的超导电性。在此,我们对Gd-Ba-Cu-O体系掺氯后的物相变化情况,用X射线粉末衍射和电     

超导相(Bi_(1.7)Pb_(0.2)In_(0.1))Sr_2Ca_2Cu_3O_(10)的制备和晶体结构研究

Bi-Sr-Ca-Cu-O体系的掺杂可以改善超导性能和消除堆垛层错。由于铋氧双层的作用还未能很好地了解,我们合成X_2Sr_2Ca_2Cu_3O_(10)的纯相,[X为(Bi_(0.85)Ph_(0.1)In_(0.05)]以确定其是(XOXO)还是(XO_2X),以及如何影响晶体结构,超导性质和生成机理。合成和鉴定CaCO_3、SrO、CuO的混合物于900℃烧结20hr得到Sr_2Ca_2Cu_3O_7,然后与Bi_2O_3、PbO按摩尔比1∶0.87∶0.3混匀,压片,于870℃加热20hr,重新研磨,在880℃加热30hr,再加0.6%mol In_2O_3,于890℃烧结20hr,然后在空气中淬火,样品表面部分微熔。     

Metastable 11 K Superconductor Na(1-y)Fe(2-x)As(2)

The topochemical deintercalation of Na(+) ions from solid NaFeAs at room temperature in THF with iodine yields the superconducting phase Na(1-y)Fe(2-x)As(2) (T(c) ≈ 11 K). This metastable iron arsenide decomposes at 120 °C and is not accessible by high-temperature solid-state synthesis. X-ray powder diffraction confirms the ThCr(2)Si(2)-type structure, but reveals very small coherently scattering domains with a mean composition Na(0.9(2))Fe(1.7(1))As(2). HRTEM investigations show crystalline as well as strongly distorted areas with planar defects. The latter are probably due to sodium loss and disorder which is also detected by (23)Na solid state NMR. The (57)Fe-M?ssbauer spectrum of Na(1-y)Fe(2-x)As(2) shows one type of iron atoms in tetrahedral coordination. All results point to one crystallographic phase with very small domains due to fluctuations of the chemical composition. From electronic reasons we suggest the superconducting phase is presumably NaFe(2)As(2) in the ordered fractions of the sample.     

Comparison of liquid chromatographic behaviors on N-methylimidazolium functionalized ZrO(2)/SiO(2)-4 and N-methylimidazolium functionalized SiO(2) stationary phases

A new stationary phase N-methylimidazolium functionalized ZrO(2)/SiO(2)-4 (Zr/SilprMim) has been prepared. The chromatographic property of this stationary phase is investigated by ion chromatography (IC) with inorganic and organic anions, and normal phase HPLC with basic compounds and hydroxybenzenes. The effects of pH and the strength of Lewis base of eluent on separation of anions are studied. This new stationary phase is also compared with a N-methylimidazolium functionalized SiO(2) stationary phase (SilprMim). The results show that this new stationary phase can be used in analysis of inorganic anions with great prospects. At the same time, successful separations of some organic anions can be obtained by using phosphate buffer solution as mobile phase. This new stationary phase also has a distinct advantage in the separation of basic compounds in normal phase. But due to the presence of Lewis acid sites on the surface of ZrO(2)/SiO(2)-4, Lewis bases such as hydroxybenzenes adsorb very strongly on this new stationary phase, and Lewis acid sites can be masked or modified by the eluent that contain Lewis base groups.     

Topological metastability and oxide ionic conduction in La(2)-(x)Eu(x)Mo(2)O(9)

The effect of partial substitution, up to x = 0.4, of La by trivalent Eu on the phase stability, thermal expansion, and transport properties of La2Mo2O9 are investigated using temperature-controlled X-ray powder diffraction, differential thermal analysis, and complex impedance spectroscopy. At low europium content (x < or = 0.1), the alpha-beta phase transition is observed at a temperature dependent on the sample shaping (powder, pellet, etc.). At high europium content (x > or = 0.25), the samples remain cubic (beta phase), regardless of the shaping. In the intermediate range of europium content (x = 0.15, 0.2), the phase stability is highly sensitive to the thermal history and the sample shaping, with a double-reversed beta-alpha-beta transition suppressed by the shaping/sintering process. The influence of the amount of europium on the transport mechanisms and parameters is studied in both low- (Arrhenius) and high-temperature (Vogel-Tammann-Fulcher = VTF) regimes. If the effect of substitution is rather mild and monotonous within each transport regime and crystallographic phase, an abrupt change in the Arrhenius parameters between the alpha- and beta-type phases is observed.     

一种合成聚(2-甲氧基-5-(2′-乙基-己氧基)-对苯乙炔)的新方法

聚对苯乙炔 (ＰＰＶ)及其衍生物是制备聚合物发光二极管的最重要的聚合物之一[1] .这主要是因为它们具有优越的电致发光性能 ,易于合成以及良好的环境稳定性[2 ] .而聚 (2 甲氧基 5 (2′ 乙基 己氧基 ) 对苯乙炔 ) (ＭＥＨ ＰＰＶ)由于其可溶性好 ,发光效率和亮度高 ,在电致发光领域广受关注 .现在有许多ＭＥＨ ＰＰＶ的多步化学合成方法以及电化学合成方法 .但是 ,这些方法常常产率低 ,成本高且产品不纯 .本文报道一种固 液两相反应一步合成分子量大、溶解性好的ＭＥＨ ＰＰＶ的新方法 .1　主要原料对甲氧基苯酚 (纯度≥ 98% ,Ａｌｄｒ…     

Reactive Uptake of N(2)O(5) on Aqueous H(2)SO(4) Solutions Coated with 1-Component and 2-Component Monolayers

Reactive uptake of N(2)O(5) on aqueous sulfuric acid solutions was studied in the presence of 1-component (octadecanol) and 2-component (octadecanol + phytanic acid) monolayers. In the 1-component monolayer experiments, the reactive uptake coefficient depended strongly on the molecular surface area of the surfactant. Also, the 1-component monolayer showed significant resistance to mass transfer even when the fractional surface coverage of the surfactant was less than 1. For example, a monolayer of 1-octadecanol with a fractional surface coverage of 0.75 decreased the reactive uptake coefficient by a factor of 10. This is consistent with previous studies. In the 2-component monolayer experiments, the reactive uptake coefficient depended strongly on the composition of the monolayer. When the monolayer contained only straight-chain molecules (1-octadecanol), the reactive uptake coefficient decreased by a factor of 42 due to the presence of the monolayer. However, when the monolayer contained 0.20 mole fraction of a branched surfactant (phytanic acid) the reactive uptake coefficient only decreased by a factor of 2. Hence, a small amount of branched surfactant drastically changes the overall resistance to reactive uptake. Also, our results show that the overall resistance to reactive uptake of 2-component monolayers can be predicted reasonably accurately by a model that assumes the resistances to mass transfer can be combined in parallel.     

LiTi2(PO4)3/C 复合材料的制备及电化学性能

采用聚乙烯醇(PVA)辅助溶胶-凝胶法合成了具有Na+超离子导体(NASICON)结构的LiTi2(PO4)3/C复合材料.运用X射线衍射(XRD)、扫描电子显微镜(SEM)、充放电测试、循环伏安(CV)、电化学阻抗谱(EIS)等对其结构形貌和电化学性能进行表征.实验结果表明:合成的LiTi2(PO4)3/C具有良好的NASICON结构,首次放电容量为144mAh·g-1.电化学阻抗谱测试结果显示,LiTi2(PO4)3/C复合材料电极在首次嵌锂过程中分别出现了代表固体电解质相界面(SEI)膜及接触阻抗、电荷传递阻抗和相变阻抗的圆弧,并详细分析了它们的变化规律.计算了Li+在LiTi2(PO4)3中嵌入/脱出时的扩散系数,分别为2.40×10-5和1.07×10-5cm2·s-1.     

Magnetic structure of Ni(DCOO)2(D2O)2

Ni(HCOO)(2)(H(2)O)(2) is a structurally simple coordination polymer showing interesting magnetic phase transitions at low temperature (<16K). Previously published studies of these phase transitions have yielded inconsistent results, questioning the correctness of the published magnetic structure. Here heat capacity and magnetic susceptibility of a fully, a partly and a non-deuterated sample were measured, and they all exhibit magnetic phase transitions around 3 and 15 K. Neutron powder diffraction data was collected on the fully deuterated sample at various temperatures between 1.5 and 25 K. A magnetic model was refined against the neutron diffraction data using a spin system composed of two canted antiferromagnetic sublattices. The magnetic moments of the two sublattices show different magnitude, 1.7 μ(B) and 1.3 μ(B), and the temperature dependence of the magnetic sublattices is quite different. One of the sublattices shows the expected temperature behavior of an antiferromagnetic compound whereas the other sublattice follows a Brillouin like function with a slowly increasing magnetization below the Ne?el temperature.     

Characterization of Pore Structure and Coordination of Titanium in TiO(2) and SiO(2)-TiO(2) Sol-Pillared Clays

Titania sol-pillared clay (TiO(2) PILC) and silica-titania sol-pillared clay (SiO(2)-TiO(2) PILC) were synthesized by the sol-gel method. Supercritical drying (SCD) and treatment with quaternary ammonium surfactants were used to tailor the pore structure of the resulting clay. It was found that SCD approach increased the external surface area of the PILCs dramatically and that treatment with surfactants could be used to tailor pore size because the mesopore formation in the galleries between the clay layers follows the templating mechanism as observed in the synthesis of MCM-41 materials. Highly mesoporous solids were thus obtained. In calcined TiO(2) PILC, ultrafine crystallites in anatase phase, which are active for photocatalytic oxidation of organics, were observed. In SiO(2)-TiO(2) PILCs and their derivatives, titanium was highly dispersed in the matrix of silica and no crystal phase was observed. The highly dispersed titanium sites are good catalytic centers for selective oxidation of organic compounds. Copyright 2001 Academic Press.     

旋转铂盘电极上Cu(phen)_2~(2 )与6-巯基嘌呤的相互作用

在Tris-NaC1*(pH=7.2)缓冲溶液中,应用循环伏安法,微分脉冲伏安法、旋转圆盘电极实验、交流阻抗法及其数据模拟等技术研究了Cu(phen)2 25(phcn=1.10-邻菲咯啉)与6-巯基嘌呤(6-MP)的相互作用.结果显示.Cu(phen)2 2MP与6-MP无论在扩散控制过程或电化学控制过程都发生了相互作用.Cu(phen)2 2及其与6-MP的作用产物于铂电极上均呈现一对氧化还原峰,但后者呈现的氧化还原峰负移.峰电流减小.交流阻抗结果显示,无论6-MP存在与否,Cu(phen)2 2在交流阻抗谱上均呈现两个清晰的电容弧,但当6-MP存在时,电化学反应电阻和电化学吸脱附电阻均增大.Cu(phen)2 2在不同转速下的阻抗拟合结果显示.随转速增大.电化学反应电阻和电化学吸脱附电阻均减小.双电层电容呈增大趋势,而吸脱附电容呈减小趋势:当6-MP存在时.仍然呈现此变化规律.     

Cubic form of Pb(2-x)Sn(x)S2 stabilized through size reduction to the nanoscale

We demonstrate the synthesis of semiconductor Pb(2-x)Sn(x)S(2) nanocrystals with a cubic rock salt crystal structure in a composition range where this structure is unstable in the bulk. The cubic Pb(2-x)Sn(x)S(2) nanocrystals were prepared using a modified hot injection colloidal synthetic route. The x value is in the range 0.40 < x < 1. Even though these compositions lie in a region of the PbS-SnS phase diagram where no single phase exists, and despite the fact that PbSnS(2) is a distorted orthorhombic phase, the Pb(2-x)Sn(x)S(2) nanocrystals are single phase solid solutions with cubic NaCl-type structure. Experimental evidence for this derives from powder X-ray diffraction (PXRD), electron diffraction, and pair distribution function (PDF) analysis. Elemental compositions determined using scanning transmission electron microscopy/energy dispersive spectroscopy (STEM/EDS), inductively coupled plasma-atomic emission spectroscopy (ICP-AES), and electron energy loss spectroscopy (EELS) reveal a composition close to the nominal ones. The band gaps of the Pb(2-x)Sn(x)S(2) nanocrystals (0.52-0.57 eV) are blue-shifted by quantum confinement relative to that of the hypothetical cubic PbSnS(2) phase which density functional theory (DFT) calculations show to be much narrower (0.2 eV) than in the case of orthorhombic PbSnS(2) (1.1 eV). The Pb(2-x)Sn(x)S(2) nanocrystals exhibit a well-defined band gap in the near-IR region and are stable up to ~300 °C above which they phase separate into cubic PbS and orthorhombic α-SnS.