Synthesis of CaCO3 nanoparticles via citrate method and sequential preparation of CaO and Ca(OH)2 nanoparticles

Calcium carbonate nanoparticles were synthesized via so‐called sol–gel citrate method using calcium nitrate as precursor in presence of different concentration of citric acid, selected to be 0.0, 0.5, 1.25 and 2.5 times of the concentration of the precursor, on calcining at 600 °C for 5 h. Stable phase of the calcite is formed in presence of citric acid. The roles of organic additive concentration, calcination temperature and sonication on the particle size of the products were investigated. Calcium oxide nanoparticles were prepared by facial calcination of the resulted product at 900 °C for 5 h. Calcium hydroxide nanoparticles, however, were synthesized on sonication of the product for 20 min in water at room temperature. Samples were characterized by XRD and FT‐IR studies. Crystallite size of samples was calculated by XRD data and was measured by TEM analysis. The specific surface are (SSA) of samples was calculated by the XRD data and compared by the measured BET. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

The effect of calcination temperature on the crystallinity of TiO2 nanopowders

TiO₂ nanopowders have been prepared using 0.1 M titanium tetraisopropoxide (TTIP) in varied pH aqueous solution containing TMC and NP-204 surfactants. Only the powder acquired from a solution of pH=2 has a regular particle size distribution. Anatase phase powders are obtained by calcination in nitrogen in the 250–500°C temperature range. When calcined at 400°C, the diameter of the nanoparticles is approximately 10 nm with a specific surface area of 106.9 m²/g. As the calcination temperature is increased, the particle size increases. Rutile phase powders are formed at calcination temperatures above 600°C.     

Solvothermal synthesis of flower‐like lanthanum tartrate and lanthanum oxide microspheres in ethanol‐water mixed system

Monodispersed lanthanum tartrate microspheres with flower‐like shape were synthesized by a mild solvothermal method using ethanol‐water mixed system as the solvent. Lanthanum oxide with reserved spherical shape was subsequently fabricated by a following calcination process. X‐ray diffraction analyses (XRD), X‐ray spectroscopy (EDS), scanning electron microscopy (SEM), thermogravimetry‐differential thermal analysis (TG‐DTA) were employed to characterize the composition, structure, and morphology of the products. The lanthanum tartrate microspheres were aggregated by nanosheets as petals. Size of the aggregation and thickness of the petal vary with the vol.% of ethanol. As the vol.% of ethanol increases the degree of aggregation and the thickness of the petal decrease, and other properties such as the size distribution, dispersion are also modulated. These alterations can be interpreted by the changing dielectric constant of mixed solvent. Such lanthanum tartrate can be applied to fabricate micro‐sphereshaped lanthanum oxide after calcination. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Size-controlled synthesis of LaAlO3 by reverse micelle method: Investigation of the effect of water-to-surfactant ratio on the particle size

Lanthanum monoaluminate (LaAlO₃) nanoparticles have been synthesized using microreactors made of poly(oxyethylene) nonylphenyl ether (Igepal CO-520)/water/cyclohexane microemulsions. The control of particle size was achieved by varying the water-to-surfactant molar ratio. The synthesized and calcined powders were characterized by thermogravimetry–differential thermal analysis (TGA-DTA), X-ray diffraction analysis (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Fourier transform infrared spectroscopy (FTIR). Differential thermal analysis showed that LaAlO₃ phase transformation decreases with increase in water/surfactant (R) value. Pure LaAlO₃ phase was synthesized by annealing at 800 °C for 2 h in air directly from amorphous precursors, without formation of intermediate phase. The average particle size was found to increase with increase in water-to-surfactant ratio (R). FTIR analysis was carried to monitor the elimination of residual oil and surfactant phases from the microemulsion-derived precursor and calcined powder.     

Formation of the Perovskite Phase Pb3NiNb2O9

Pb₃NiSNb₂O₉ was synthesized via various methods in order to investigate the mechanisms of perovskite formation. Two relatively simple routes to precursors that give single-phase perovskite after calcination at 900°C are described: a modified columbite-method and a synthesis from a freezedried complex salt solution. The results show that the formation of perovskite Pb₃NiNb₂O₉ does not start below 900 °C and that the pyrochlore formation beginning at lower temperatures has be hindered by a thermal shock calcination.     

Direct preparation of K0.5Na0.5NbO3 powders

K_0.5Na_0.5NbO₃ powders have been directly synthesized by an alternative solid–state method. Stoichimometric mixture of ammonium niobium oxalate and C₄H₄O₆KNa·4H₂O were calcined in temperature range from 500 to 800 °C for 3 h. The precursor and calcination products were characterized with respect to stoichiometry, purity, crystalline structure, particle size and powder morphology using X–ray diffraction (XRD), X‐ray fluorescence (XRF) spectrometer, scanning electron microscope (SEM), Fourier transform infrared (FTIR) spectra, thermogravimetric (TG) analysis, differential scanning calorimetry (DSC) and UV–Vis diffuse reflectance (UV–Vis) spectroscopy. XRD and XRF results reveal that stoichiometric K_0.5Na_0.5NbO₃ powders could be synthesized by the method. The particle size is about 68 nm for the precursor calcined at 500 °C according to XRD data, which is in good agreement with SEM data. The average band gap energy is estimated to be 3.18 eV by UV–vis diffuse reflectance spectra. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of citric acid concentration as emulsifier on perovskite phase formation of nano‐sized SrMnO3 and SrCoO3 samples

In this study the effects of citric acid concentration, used as organic emulsifier, on the perovskite phase formation of the nano strontium manganite or cobaltite samples were studied. Stoichiometric perovskites in the absence and presence of citric acid were prepared by drying a solution containing molar ratio of Sr(NO₃)₂/Mn(NO₃)₂·4H₂O and Sr(NO₃)₂/Co(NO₃)₂·6H₂O = 1 followed by calcination at 900 °C for 5 h. Citric acid concentration, selected to be 0.0, 0.3, 0.6, 1.0, 1.3, 2.5 and 5 times of the total number of moles of the nitrate ions. The results revealed that increase in the citric acid concentration, larger than number of moles of the nitrate ions equivalent, deteriorates the perovskite phase formation. Instead, a new phase of carbonates and metal oxides are appeared. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural and optical properties of CdO nanowires synthesized from Cd(OH)2 precursors by calcination

CdO nanowires were produced by calcination process using Cd(OH)₂nanowires as precursors. The Cd(OH)₂ nanowires were synthesized via arc discharge method submerged in de‐ionized water. Transmission electron microscopy (TEM) analysis of the as‐synthesized Cd(OH)₂ nanowires revealed that nanowire morphology was abundant form with the diameters range from 5 to 40 nm. In addition to the nanowire morphology, Cd(OH)₂ nanospheres and hexagonal shaped nanoparticles were also displayed. The Cd(OH)₂ nanostructures were used as precursors to produce CdO nanowires and calcinated in air at 400 °C for four hours. After calcination, the structural, morphological and optical properties of the as‐synthesized CdO nanowires were characterized by means of TEM, selected area electron diffraction (SAED), X‐ray diffraction (XRD) and UV‐vis spectroscopy. The XRD and SAED techniques showed that the as‐synthesized Cd(OH)₂ nanostructures could be transformed into CdO nanostructures after the calcination process. TEM results revealed that the as‐synthesized CdO nanowires were 5–30 nm in diameter and shorter than corresponding Cd(OH)₂ nanowires. In addition, the diameters of the spherical or irregular CdO nanoparticles ranged from 20 nm to 50 nm. UV‐vis spectroscopy analysis was showed that the direct gap of the CdO nanowires were found to be 2.60 eV which is slightly higher than the earlier reported values of the bulk CdO for direct band gaps (2.3 eV) due to quantum size effect. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Morphology and crystal structure of A1-doped TiO2 nanoparticles synthesized by vapor phase oxidation of titanium tetrachloride

Al-doped titanium dioxide nanoparticles with precisely controlled characteristics were synthesized in an aerosol reactor between 900 °C and 1500 °C by vapor-phase oxidation of titanium tetrachloride. The effect of process variables (reactor temperature, initial TiCl₄ concentration, residence time and feeding temperature of oxygen) on particle morphology and phase characteristics was investigated using TEM, XRD, EDS, ICP and XPS, etc. The average particle size increased with decreasing oxygen feeding temperature and increasing reaction temperature, residence time and TiCl₄ concentration. The presence of aluminum during gas phase reaction increased the rate of phase transformation from anatase to rutile and altered the particle morphology from polyhedral to irregular crystals. TiO₂ and Al₂O₃ co-precipitated during particle formation which lead to the aluminum solid solution in titania. α-Al₂O₃ and Al₂TiO₅ were observed at AlCl₃/TiCl₄ ratios higher than 1.1 and reactor temperatures in excess of 1400 °C. The rutile content, which increased with increasing Al/Ti ratio and residence time, was at a maximum at about 1200 °C and decreased at both lower and higher reactor temperatures.     

Preparation and characterization of indium doped tin oxide (ITO) via a non-aqueous sol-gel

ABSTRACT

Tin-doped indium oxide (ITO) nanoparticles (NPs) were conceived as promising materials using as noncarbon support for Pt NPs on the cathode side of Proton Exchange Membrane Fuel Cells (PEMFC). In this paper, ITO nanoparticles have been synthesized via a nonaqueous sol-gel process using indium acetylacetonate and tin bis(acetylacetonate)dichloride in oleyamine as starting materials. The ITO exhibits solid solution phase, relatively porous, good crystallinity with a uniform size of 15–20 nm, resulting in a high specific surface area and excellent conductivity. The effects of reaction temperature, calcination temperature on the specific surface area as well as the conductivity of ITO nanoparticles were studied in this paper. We found that the ITO nanoparticles synthesized at 235°C and calcination temperature at 500°C for 3 hours shows the excellent conductivity of 1.242 S/cm, was significantly ～8-fold higher than that of commercial ITO produced by Sigma-Aldrich (0.15 S/cm). The results of this research suggested that the ITO synthesized by non-aqueous sol-gel process exhibits relatively good properties as well as can apply this process to prepare the others nanomaterial support based on In₂O₃-materials by doping different oxide into indium oxide.     

Effect of Thermal Annealing on Structural Properties,Morphologies and Electrical Properties of TiO2 Thin Films Grown by MOCVD

TiO₂ thin films, were deposited on Si(100) and Si(111) substrates by metalorganic chemical vapor deposition at 500 °C, and have been annealed for 2 min, 30 min and 10 hours at the temperature from 600 °C to 900 °C, in oxygen and air flow, respectively. XRD and atomic force microscopy characterized the structural properties and surface morphologies of the films. As‐deposited films show anatase polycrystalline structure with a surface morphology of regular rectangled grains with distinct boundaries. Rutile phase formed for films annealed above 600 °C, and pure rutile polycrystalline films with (110) orientation can be obtained after annealing under adequate conditions. Rutile annealed films exhibit a surface morphology of equiaxed grains without distinct boundaries. The effects of substrate orientation, annealing time and atmosphere on the structure and surface morphology of films have also been studied. Capacitance‐Voltage measurements have been performed for films deposited on Si(100) before and after annealing. The dielectric properties of TiO₂ films were greatly improved by thermal annealing above 600 °C in oxygen.     

煅烧温度对溶胶-凝胶合成BCZT纳米粉体的影响

针对传统固相反应法制备粉体存在的成分偏离和引入杂质等问题,采用溶胶-凝胶方法合成了0.5Ba(Zr0.2Ti0.8)O3-0.5(Ba0.7Ca0.3) TiO3(BCZT)无铅纳米粉体,主要研究了煅烧温度对其结构和形貌的影响.TG-DSC、XRD、SEM、TEM、FTIR等测试结果表明:在900～1100℃的温度范围内,溶胶-凝胶合成的BCZT粉体表现为单一的立方相结构;随着煅烧温度的升高,粉体的结晶性逐渐增强,颗粒尺寸增大;适宜的粉体煅烧温度为900,与传统固相反应法相比可降低约400℃;在此煅烧温度下得到的BCZT粉体粒径均匀,尺寸约50 ～ 60 nm,结晶良好,成分均匀.     

Preparation of nanocrystalline lithium niobate powders at low temperature

A facile route to prepare lithium niobate (LiNbO₃) powders was proposed by an alternative solid‐state method. Stoichiometric Li₂C₂O₄ and ammonium niobium oxalate were mixed with small amounts of water and then dried at room temperature. It was demonstrated that Li[NbO(C₂O₄)₂]·n H₂O intermediate was produced by an ion‐exchange reaction. Pure LiNbO₃ powders were successfully synthesized by heating the intermediate at 500, 600 and 700 °C for 3 h. X‐ray diffraction (XRD), scanning electron microscopy (SEM), Fourier‐transform infrared (FTIR) spectroscopy, UV‐Vis diffuse reflectance (UV‐Vis) spectroscopy and thermogravimetric (TG) analysis were used to characterize the precursor compound and as‐prepared samples. XRD results reveal that all the products are identified as hexagonal structure with high relative crystallinity (>87%). The particle size is found to be about 40 nm for the mixture calcined at 500 °C according to XRD data, which is in good agreement with SEM data. The as‐prepared LiNbO₃ powders by this method are high quality according to FTIR spectra. (Li_0.996Nb_0.005)Nb_0.999O₃ phase was formed when the calcination temperature was raised to 800 °C. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis of mercuric iodide and bismuth tri‐iodide nanoparticles for heavy metal iodide films nucleation

We synthesized mercuric iodide and bismuth tri‐iodide nanoparticles by suspension in octadecene, from Hg(NO₃)₂.H₂O and I₂, and from Bi(NO₃)₃.5H₂O and I₂, respectively. The best synthesis conditions were 2 h at 70‐80 °C, followed by 10 min at 110 °C for mercuric iodide nanoparticles, and 4 h at 80‐110 °C, followed by 10 min at 180‐210 °C for bismuth tri‐iodide ones. Nanoparticles were then washed and centrifuged with ether repeatedly. Compounds identity was confirmed by X‐ray diffraction (XRD) and energy dispersive spectrometry (EDS). We found shifts of the X‐ray diffraction maxima for nanoparticles of both compounds. We characterized the nanoparticles by transmission (TEM) and scanning (SEM) electron microscopy. We obtained disk‐like and squared mercuric iodide nanostructures, 80‐140 nm and 100‐125 nm in size respectively. We also obtained rounded and rod‐like bismuth tri‐iodide nanoparticles, 30‐500 nm in size. Acetonitrile and isopropanol suspensions of mercuric iodide nanoparticles, and acetonitrile suspension of bismuth tri‐iodide nanoparticles exhibited peak maxima shifts in their UV‐Vis spectra. We synthesized for the first time mercuric iodide and bismuth tri‐iodide nanoparticles by the suspension method, although we have not yet obtained uniform shape and size distributions. They offer interesting perspectives for crystalline film nucleation and for improving current applications of these materials, as well as for opening new ones. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

TiO2 nanoparticles synthesis for application in proton exchange membranes

In the present paper, suitable TiO₂ nanoparticles are successfully synthesized by sol‐gel method, in order to utilize the freshly prepared TiO₂ nanoparticles for proton exchange membrane (PEM) preparation. Titanium tetrachloride (TiCl₄) is used as precursor and ethanol as a solvent. The optimum and suitable TiO₂ nanoparticles were obtained by varying gelatinisation time (4–120 h), concentration of precursor (TiCl₄) in ethanol (2–15 vol%), and reaction temperature (15–35 °C). The morphology, size and purity of the nanoparticles are investigated by transmission electron microscope (TEM), dynamic light scattering (DLS) and X‐ray diffraction (XRD). Optimum results were found at 4 h of gelatinisation time, 10% precursor concentration and 25 °C temperature for preparation of TiO₂ nanoparticles. Thus prepared nanoparticles are found to be suitable for preparation of nanocomposite PEM, and consequently the prepared PEM indicates enhanced properties, such as, higher thermal stability (high glass transition temperature of 184.1 °C), excellent proton conductivity (0.0822 S cm⁻¹ at room temperature) and low methanol permeability (1.11 × 10⁻⁹ cm2 s⁻¹).     

A novel thermolysis method of colloidal protein precursors to prepare hydroxyapatite nanocrystals

A novel thermolysis method of colloidal protein precursors is introduced to prepare hydroxyapatite (HAP) nanocrystals. The colloidal protein precursors are sonochemically synthesized from saturated Ca(OH)₂ aqueous solution, Ca(H₂PO₄)₂ aqueous solution and bovine serum albumin (BSA) molecules. The colloidal protein precursors are amorphous and composed of 15‐90 nm near spherical calcium phosphate nanoparticles and BSA molecules. The particle size analysis shows the volume particle size distribution is from 9.0 nm to 222.6 nm and the volume‐averaged particle size is 45.8 nm. During the calcination procedure BSA molecules are burningly removed and the HAP nanocrystals can be obtained at 500 °C. The effects of BSA concentration on the properties of samples are discussed. Results show that BSA combustion can promote the transformation of crystalline HAP from amorphous material. Moreover, the increase of BSA concentration reduces the crystalline sizes of HAP crystals and the crystallinity of product. With BSA concentration of 5 g/L, the obtained HAP nanocrystals are mainly 25∼100 nm similar spherical nanoparticles besides some 40∼70 nm×75∼150 nm short rod‐like crystals. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

A novel approach for the synthesis of monodispersed porous silica microspheres with high surface area

Monodispersed porous silica microspheres are synthesized by the hydrolysis and condensation of tetraethoxysilane (TEOS) in a water–ethanol mixed solution containing 1-alkylamine as a template and hydrolysis catalyst. The as-prepared products were characterized with scanning electron microscopy (SEM), transmission electron microscopy (TEM), small angle X-ray diffraction (SAXRD), Fourier transform infrared spectroscopy (FTIR) and nitrogen adsorption, respectively. It was found that the alkyl chain length of 1-alkylamine and calcination temperature have an obvious influence on the particle size, morphology, specific surface area and pore structure of the as-prepared silica powder. The specific surface area, porosity and pore volume increased with increasing calcination temperature. Further observation showed that at 600 °C, with increasing the alkyl chain length of template from C₁₂ to C₁₈, the specific surface area decreased and the pore size, porosity and pore volume increased. This research may provide new insight into the control of morphology and pore structures of oxide materials.     

纳米ZnO合成中醇水体系和熔盐介质的粒径调控效应研究

采用液相法制备了纳米ZnO,在沉淀过程中采用乙醇-水混合溶液,煅烧过程中加入碱金属硝酸盐介质,以研究两者对粒径的调控作用和机理.并利用XRD、TEM、BET和PL等测试手段进行产物表征.结果表明:相同条件下,采用NaNO_3和LiNO_3熔盐辅助煅烧后,产物粒径较直接煅烧明显减小;同量的LiNO_3相对于NaNO_3,其产物粒径小于后者;当醇水比例增加时,由于介电常数的减小,产物粒径也明显减小.最后讨论了醇水体系和熔盐介质粒径调控的机理.     

Synthesis of BaCeO3 powders by a fast aqueous citrate–nitrate process

A fast aqueous citrate–nitrate process has been successfully used to prepare the stoichiometric BaCeO₃ powders. It was found that an optimal amount of water added in the mixing process of barium nitrate, cerium nitrate, and citric acid is helpful on the formation of a clear gel that was subsequently formed by the condensation of added diethylene glycol monomers at room temperature. The gel was heated to an easily handled precursor in a powder form at 400 °C for 1 h. The precursors were characterized by X-ray powder diffraction (XRD), differential thermal analysis (DTA), thermal gravimetric analysis (TGA), thermal mechanical analysis (TMA), Fourier transform infrared spectrometry (FTIR), and scanning electron microscopy (SEM). The phase evolution from the precursor to the desired BaCeO₃ powders by XRD and FTIR revealed that the presence of BaCO₃ is a complex problem in this process. A high-temperature trigonal BaCO₃ intermediate was found between 800 °C and 1000 °C by the in-situ X-ray powder diffraction experiments. The phase purity of the formed BaCeO₃ powders may be more properly identified by FTIR instead of XRD because of the amorphous feature of the carbonate phase. The TMA revealed that at 1100 °C part of the precursor crystallized to needle-shaped BaCeO₃ crystals accompanied by a small expansion, which is also related to the presence of BaCO₃ in the precursor, and this can be removed by a preheating treatment of the precursor at 900 °C for 4 h.     

An X‐ray powder diffraction study of the microstructural evolution on heating 3:2 and 2:1 mullite single‐phase gels

Single‐phase gels with compositions 3Al₂O₃·2SiO₂ and 2Al₂O₃·SiO₂ were prepared by gelling mixtures of aluminium nitrate and tetraethylorthosilicate. Gels were fast heated at different temperatures between 900°C and 1600°C. The phase transformation and microstructural changes of both mullite precursor gels over the temperature range were followed by X‐ray powder diffraction (XRD), lattice parameter determination (LP), and scanning and transmission electron microscopies (SEM and TEM). The distribution of crystallite sizes and strains were determined by linewidth refinements of X‐ray diffraction patterns using the integral breadth method of Langford and the Warren‐Averbach analysis. XRD of both heated gels showed the formation of crystalline mullite single phase. Some amount of glassy phase coexisted with mullites at low temperatures, i. e. below 900°C. The compositional range of mullites formed on heating gels at temperatures between 900°C and 1600°C was dependent on the starting nominal composition of gels. SEM and TEM micrographs of both heated gels below 1200°C showed the formation of small, discrete, prismatic, well‐shaped nanocrystals in a very ordered arrangement. The size of these nanocrystals was dependant on the nominal composition of gels and increased on rising the heating temperature of gel precursors. The microstructural features obtained from linewidth refinement results of X‐ray diffraction patterns also allowed to suggest the formation of prismatic a little elongated nanocrystals at temperatures below 1200°C. Microstrain values were small and only displayed a relatively significant value for mullites processed at 900°C. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)