Investigation of the vibrational modes of ZnO grown by MOCVD on different orientation planes

Wurtzite ZnO thin films were prepared on sapphire substrate by metal organic chemical vapor deposition (MOCVD). Raman scattering studies on different crystallographic textures were performed in the backscattering geometry, and polarization effect is investigated in different configurations and . ZnO Raman modes are investigated in each texture. In the case of ZnO thin film deposed on r‐() sapphire plane and using backscattering geometry, new Raman line was observed at 390 cm⁻¹ because this mode has not been noticed in this geometry. It is shown that the frequencies of the quasi‐phonon modes of the examined thin film are in good agreement with the theoretical values calculated within the framework of Loudon model. Copyright © 2014 John Wiley & Sons, Ltd.     

Phonon anomalies and structural transition in spin ice Dy2Ti2O7: a simultaneous pressure‐dependent and temperature‐dependent Raman study

We revisit the assignment of Raman phonons of rare‐earth titanates by performing Raman measurements on single crystals of O¹⁸ isotope‐rich spin ice and nonmagnetic pyrochlores and compare the results with their O¹⁶ counterparts. We show that the low‐wavenumber Raman modes below 250 cm⁻¹ are not due to oxygen vibrations. A mode near 200 cm⁻¹, commonly assigned as F_2g phonon, which shows highly anomalous temperature dependence, is now assigned to a disorder‐induced Raman active mode involving Ti⁴⁺ vibrations. Moreover, we address here the origin of the ‘new’ Raman mode, observed below T_C ~ 110 K in Dy₂Ti₂O₇, through a simultaneous pressure‐dependent and temperature‐dependent Raman study. Our study confirms the ‘new’ mode to be a phonon mode. We find that dT_C/dP = + 5.9 K/GPa. Temperature dependence of other phonons has also been studied at various pressures up to ~8 GPa. We find that pressure suppresses the anomalous temperature dependence. The role of the inherent vacant sites present in the pyrochlore structure in the anomalous temperature dependence is also discussed. Copyright © 2012 John Wiley & Sons, Ltd.     

A comparison between ab initio calculated and measured Raman spectrum of triclinic albite (NaAlSi3O8)

Albite is one of the most common minerals in the Earth's crust, and its polymorphs can be found in rocks with different cooling histories. The characteristic spectrum of vibration of the albite mineral reflects its structural Si/Al ordering. In this study, we report on the comparison between the Raman spectra measured on a natural and fully ordered (as deduced on the basis of single‐crystal X‐ray diffraction data) ‘low albite’, NaAlSi₃O₈, and those calculated at the hybrid Hartree–Fock/density functional theory level by employing the WC1LYP Hamiltonian, which has proven to give excellent agreement between calculated and experimentally measured vibrational wavenumbers in silicate minerals. All the 39 expected A_g modes are identified in the Raman spectra, and their wavenumbers and intensities, in different scattering configurations, correspond well to the calculated ones. The average absolute discrepancy is ~3.4 cm⁻¹, being the maximum discrepancy |Δv|_max ~ 10.3 cm⁻¹. The very good quality of the WC1LYP results allows for reliable assignments of the Raman features to specific patterns of atomic vibrational motion. Copyright © 2015 John Wiley & Sons, Ltd.     

Resonant Raman scattering of graphite intercalation compounds KC8, KC24, and KC36

Graphite intercalation compounds, due to charge transfer between layers of graphite and intercalants, have a strongly shifted Fermi level. Potassium is known to give its electron leading to a large charge transfer f_c close to for stage 1 (KC₈) and for stage 2 (KC₂₄). The question is more subtle in stage 3 (KC₃₆) for which the graphene layers are not equivalent. For stage 3, two Raman G bands are clearly visible, corresponding to the interior layer and the boundary layers, respectively. By varying the excitation energy from UV to infrared, we observe that the intensity of the boundary layers G band versus that of the interior layer is maximum at 2.5 eV, leading to a sharp resonance profile at room temperature. Using first‐principle calculation, we associate this transition to π → π^∗ of the bounding layers. Copyright © 2014 John Wiley & Sons, Ltd.     

Vibrational and reorientational dynamics,crystal structure and solid–solid phase transition studies in [Ca(H2O)6]Cl2 supported by theoretical (DFT) calculations

[Ca(H₂O)₆]Cl₂ between 93 and 300 K possesses two solid phases. One phase transition (PT) of the first‐order type at = 218.0 K (on heating) and = 208.0 K (on cooling) was determined by differential scanning calorimetry. Thermal hysteresis of this PT (10 K), as well as the heat flow anomaly sharpness, suggests that the detected PT is a first‐order one. The entropy change value [ΔS ≈ 8.5 J mol⁻¹ K⁻¹ ≈ Rln(2.8)] associated with the observed PT suggests a moderate degree of molecular dynamical disorder of the high‐temperature phase. The temperature dependencies of the full width at half maximum values of the infrared band are due to ρ(H₂O)A₂ mode (at 205 cm⁻¹), and two Raman bands are arising from τ(H₂O)E and τ(H₂O)A₁ modes (at ca. 410 and 682 cm⁻¹, respectively), suggesting that the observed PT is associated with a sudden change of speed of the H₂O reorientational motions. The estimated mean value of activation energy for the reorientation of the H₂O ligands in the high‐temperature phase is ca. 11.4 kJ mol⁻¹ from Raman spectroscopy and 11.9 kJ mol⁻¹ from infrared spectroscopy. X‐ray single‐crystal diffraction measurement and spectroscopic studies (infrared, Raman and inelastic neutron scattering) also confirm that [Ca(H₂O)₆]Cl₂ includes two sets of differently bonded H₂O molecules. Ab initio calculations of the complete unit cell of one molecule of calcium chloride with a different number of water molecules (2, 4 and 6) have also been carried out. A comparison of Fourier Transform Infrared (FT‐IR), Fourier Transform Raman Scattering (FT‐RS) and inelastic neutron scattering spectroscopies results with periodic density functional theory calculations was used to provide a complete assignment of the vibrational spectra of [Ca(H₂O)₆]Cl₂. Copyright © 2016 John Wiley & Sons, Ltd.     

Hyper‐Raman and Raman scattering in paratellurite TeO2

Raman spectra of the tetragonal structure of paratellurite TeO₂ have been revisited avoiding anomalous polarization‐selection‐rules violations previously observed and due to optical activity. We present a complementary hyper‐Raman scattering study of paratellurite. Wavenumber and symmetry assignments are given for all expected 21 Raman active optical branches, except one LO component (out of the eight expected TO–LO pairs) of the polar doublet E modes. Also, the four expected hyper‐Raman active A₂ (TO) modes have been observed. Moreover, we have observed a strong Kleinman‐disallowed hyper‐Rayleigh signal, which is tentatively assigned as a first evidence of hyper‐Rayleigh optical activity. Copyright © 2013 John Wiley & Sons, Ltd.     

Raman spectroscopy of M3B7O13X boracites (M = Cr,Co,Ni,Cu,Zn,Cd; X = Cl,Br,I)

We report results of a Raman study on single crystals of 16 boracites M₃B₇O₁₃X (M = Cr,Co,Ni,Cu,Zn,Cd; X = Cl,Br,I) over a broad temperature range. The Raman modes for all boracites in their high‐temperature prototype cubic (F3c) phase are compared. With decreasing temperature, most (but not all) compounds present a transition to the low‐temperature orthorhombic phase (Pca2₁) or to a sequence of orthorhombic, monoclinic (Pa), and trigonal (R3c) phases. The variations of the Raman spectra through different phases are studied in detail. Special attention is paid to the temperature hysteresis near the transitions and the dependence of transition temperature on the direction of crystal growth for the same material. Copyright © 2014 John Wiley & Sons, Ltd.     

Ion–polymer and ion–ion interaction in PEO‐based polymer electrolytes having complexing salt LiClO4 and/or ionic liquid, [BMIM][PF6]

Ion–polymer and ion–ion association in polymer electrolyte films of PEO complexed with salt LiClO₄, ionic liquid (1‐butyl‐3‐methylimidazolium hexafluorophosphate, BMIMPF₆) and (LiClO₄ + BMIMPF₆) have been studied by laser Raman spectroscopy. The cations (Li⁺ and/or BMIM⁺) of the dopant salt/IL are shown to complex with the ether oxygen of the polymer backbone (i.e. C O C bond of PEO). The polymer–cation complexation results in the appearance of an additional peak at ∼1131 cm⁻¹ apart from the C O C stretching vibrations of PEO at ∼1062 and 1141 cm⁻¹. This peak due to polymer–cation complexation is relatively strong for LiClO₄ than BMIMPF₆, indicating stronger interaction for the former. In the PEO:LiClO₄ and PEO:BMIMPF₆ spectra, Raman peaks at 937 and 747 cm⁻¹, respectively related to Li⁺· ClO and BMIM⁺· PF ‘contact ion pairs’, have also been observed as a result of ion–ion association. In the polymer electrolyte PEO:LiClO₄ + BMIMPF₆ which contained two different anions, viz. ClO and PF, an interesting observation of the formation of ‘cross contact ion pairs’ viz. Li⁺· PF and BMIM⁺· ClO is also reported. Copyright © 2011 John Wiley & Sons, Ltd.     

Raman light scattering,infrared absorption and DSC studies of the phase transition and vibrational and reorientational dynamics of H2O ligands and ClO4– anions in [Ba(H2O)3](ClO4)2

[Ba(H₂O)₃](ClO₄)₂ between 90 and 300 K possesses two solid phases. One phase transition of the first‐order type at: = 211.3 K (on heating) and = 204.6 K (on cooling) was determined by differential scanning calorimetry. The entropy change value (ΔS ≈ 15 Jmol^–1 K^–1), associated with the observed phase transition, indicates a moderate degree of molecular dynamical disorder. Both, vibrational and reorientational motions of H₂O ligands and ClO₄^– anions, in the high‐temperature and low‐temperature phases, were investigated by Fourier transform far‐infrared and middle‐infrared and Raman light scattering spectroscopies. The temperature dependences of the full‐width at half‐maximum values of the bands associated with ρ_w(H₂O) mode, in both infrared (~570 cm^–1) and Raman light scattering (~535 cm^–1) spectra, suggest that the observed phase transition is not associated with a sudden change of a speed of the H₂O reorientational motions. Ligands reorient fast, with correlation time of the order of several picoseconds, with a mean activation energy value E_a = 5.1 kJ mol^–1 in both high and low temperature phases. On the other hand, measurements of temperature dependences of full‐width at half‐maximum values of the infrared band at ~460 cm^–1, associated with δ_d(OClO)E mode, and Raman band at ~1105 cm^–1, associated with ν_as(ClO)F₂ mode, revealed the existence of a fast ClO₄^– reorientation in phase I and in phase II, with the E_a(I) and E_a(II) values equal to 8.0 and 6.5 kJ mol^–1, respectively. These reorientational motions of ClO₄^– are slightly distorted at the T_C. Fourier transform far‐infrared and middle‐infrared spectra with decreasing of temperature indicated characteristic changes at the vicinity of PT at T_C, which suggested lowering of the crystal structure symmetry. All these experimental facts suggest that the discovered phase transition is associated with small change of H₂O ligands and somewhat major change of ClO₄^– anions reorientational dynamics, and with insignificant change of the crystal structure, too. Copyright © 2012 John Wiley & Sons, Ltd.     

DFT‐assisted interpretation of the Raman spectra of hydrogen‐ordered ice XV

The vibrational spectra of the condensed phases of water often show broad and strongly overlapping spectral features which can make spectroscopic interpretations and peak assignments difficult. The Raman spectra of hydrogen‐ordered H₂O and D₂O ice XV are reported here, and it is shown that the spectra can be fully interpreted in terms of assigning normal modes to the various spectral features by using density functional theory (DFT) calculations. The calculated lattice‐vibration spectrum of the experimental antiferroelectric structure is in good agreement with the experimental data whereas the spectrum of a ferroelectric Cc structure, which computational studies have suggested as the crystal structure of ice XV, differs substantially. Moreover, the calculated coupled O–H stretch spectrum also seems in better agreement with the experiment than the calculated spectrum for the Cc structure. Both the hydrogen bonds as well as the covalent bonds appear to be stronger in hydrogen‐ordered ice XV than in the hydrogen‐disordered counterpart ice VI. A new type of stretching mode is identified, and it is speculated that this kind of mode might be relevant for other condensed water phases as well. Furthermore, the ice XV spectra are compared to the spectra of ice VIII which is the only other high‐pressure phase of ice for which detailed spectroscopic assignments have been made so far. In summary, we have established a link between crystallographic data and spectroscopic information in the case of ice XV by using DFT‐calculated spectra. Such correlations may eventually help interpreting the vibrational spectra of more structurally‐disordered aqueous systems. Copyright © 2012 John Wiley & Sons, Ltd.     

Abnormal Raman spectra in Er‐doped BaTiO3 ceramics

Greatly enhanced and abnormal Raman spectra were discovered in the nominal (Ba_{1 − x}Er_x)Ti_{1 − x/4}O₃ (x = 0.01) (BET) ceramic for the first time and investigated in relation to the site occupations of Er³⁺ ions. BaTiO₃ doped with Ti‐site Er³⁺ mainly exhibited the common Raman phonon modes of the tetragonal BaTiO₃. Er³⁺ ions substituted for Ba sites are responsible for the abnormal Raman spectra, but the formation of defect complexes will decrease spectral intensity. A large increase in intensity showed a hundredfold selectivity for Ba‐site Er³⁺ ions over Ti‐site Er³⁺ ions. A strong EPR signal at g = 1.974 associated with ionized Ba vacancy defects appeared in BET, and the defect chemistry study indicated that the real formula of BET is expressed by (Ba_{1 − x}Er_3x/4)(Ti_{1 − x/4}Er_x/4)O₃. These abnormal Raman signals were verified to originate from a fluorescent effect corresponding to ⁴S_3/2→⁴I_15/2 transition of Ba‐site Er³⁺ ions. The fluorescent signals were so intense that they overwhelmed the traditional Raman spectra of BaTiO₃. The significance is that the abnormal Raman spectra may act as a probe for the Ba‐site Er³⁺ occupation in BaTiO₃ co‐doped with Er³⁺ and other dopants. A new broad EPR signal at g = 2.23 was discovered, which originated from Er³⁺ Kramers ions. Copyright © 2014 John Wiley & Sons, Ltd.     

Beryllium Silicate,Be2SiO4 (phenakite) – a Novel Trigonal SRS‐Active Crystal

In single crystals of the beryllium silicate Be₂SiO₄ with trigonal symmetry , known also as the mineral phenakite, χ⁽³⁾‐nonlinear lasing by stimulated Raman scattering (SRS) is investigated. All observed Stokes and anti‐Stokes lasing components are identified and ascribed to a single SRS‐promoting vibration mode with ω_SRS ≈876 cm⁻¹. With picosecond single‐wavelength pumping at one micrometer the generation of an octave‐spanning Stokes and anti‐Stokes comb is observed.     

Stimulated Raman scattering in natural crystals of fluorapatite,Ca5(PO4)3F

Hexagonal Ca₅(PO₄)₃F, known as natural crystal fluorapatite and oldest host‐crystal for Ln³⁺‐lasant ions, is presented as a Raman‐active material. High‐order Raman‐induced χ⁽³⁾‐nonlinear processes are discovered in natural crystals of fluorapatite under picosecond pumping at 1.064 μm and 0.532 μm wavelength. A multitude of Stokes and anti‐Stokes components is generated in the ultraviolet, visible and near‐infrared spectral region by stimulated Raman scattering (SRS) and Raman four‐wave mixing (FWHM), resulting in a frequency comb with a width of 520 THz. The spectral lines are identified and attributed to the ν₁(A_g) vibration mode of the tetrahedral [PO₄] units which is related to a Raman shift of ω_SRS ≈ 965 cm⁻¹. The first Stokes steady‐state Raman gain coefficient in the near‐infrared spectral range is estimated to be >0.38 cm·GW⁻¹. Finally, a short review of SRS‐promoting vibration modes and observed χ⁽³⁾‐ nonlinear interactions in all known SRS‐active natural crystals (minerals) is given.

     

Nonlinear optical characteristics of monolayer MoSe2

In this study, we utilized picosecond pulses from an Nd:YAG laser to investigate the nonlinear optical characteristics of monolayer MoSe₂. Two‐step growth involving the selenization of pulsed‐laser‐deposited MoO₃ film was employed to yield the MoSe₂ monolayer on a SiO₂/Si substrate. Raman scattering, photoluminescence (PL) spectroscopy, and atomic force microscopy verified the high optical quality of the monolayer. The second‐order susceptibility χ⁽²⁾ was calculated to be ～50 pm V^?1 at the second harmonic wavelength ～810 nm, which is near the optical gap of the monolayer. Interestingly, our wavelength‐dependent second harmonic scan can identify the bound excitonic states including negatively charged excitons much more efficiently, compared with the PL method at room temperature. Additionally, the MoSe₂ monolayer exhibits a strong laser‐induced damage threshold ～16 GW cm^?2 under picosecond‐pulse excitation_. Our findings suggest that monolayer MoSe₂ can be considered as a promising candidate for high‐power, thin‐film‐based nonlinear optical devices and applications.     

Observation of optomechanical coupling in a microbottle resonator

In this work, we report optomechanical coupling, resolved sidebands and phonon lasing in a solid‐core microbottle resonator fabricated on a single mode optical fiber. Mechanical modes with quality factors (Q_m) as high as 1.57 × 10⁴ and 1.45 × 10⁴ were observed, respectively, at the mechanical frequencies and . The maximum  Hz is close to the theoretical lower bound of 6 × 10¹² Hz needed to overcome thermal decoherence for resolved‐sideband cooling of mechanical motion at room temperature, suggesting microbottle resonators as a possible platform for this endeavor. In addition to optomechanical effects, scatter‐induced mode splitting and ringing phenomena, which are typical for high‐quality optical resonances, were also observed in a microbottle resonator.

     

Layered MoS2 grown on c ‐sapphire by pulsed laser deposition

Layered growth of molybdenum disulphide (MoS₂) was successfully achieved by pulsed laser deposition (PLD) method on c ‐plane sapphire substrate. Growth of monolayer to a few monolayer MoS₂, dependent on the pulsed number of excimer laser in PLD is demonstrated, indicating the promising controllability of layer growth. Among the samples with various pulse number deposition, the frequency difference (A_1g–E¹_2g) in Raman analysis of the 70 pulse sample is estimated as 20.11 cm^–1, suggesting a monolayer MoS₂ was obtained. Two‐dimensional (2D) layer growth of MoS₂ is confirmed by the streaky reflection high energy electron diffraction (RHEED) patterns during growth and the cross‐sectional view of transmission electron microscopy (TEM). The in‐plane relationship, (0006) sapphire//(0002)MoS₂and sapphire//MoS₂ is determined. The results imply that PLD is suitable for layered MoS₂ growth. Additionally, the oxide states of Mo 3d core level spectra of PLD grown MoS₂, analysed by X‐ray photoelectron spectroscopy (XPS), can be effectively reduced by adopting a post sulfurization process. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Chiral expansion and Macdonald deformation of two‐dimensional Yang‐Mills theory

We derive the analog of the large N Gross‐Taylor holomorphic string expansion for the refinement of q‐deformed Yang‐Mills theory on a compact oriented Riemann surface. The derivation combines Schur‐Weyl duality for quantum groups with the Etingof‐Kirillov theory of generalized quantum characters which are related to Macdonald polynomials. In the unrefined limit we reproduce the chiral expansion of q‐deformed Yang‐Mills theory derived by de Haro, Ramgoolam and Torrielli. In the classical limit , the expansion defines a new β‐deformation of Hurwitz theory wherein the refined partition function is a generating function for certain parameterized Euler characters, which reduce in the unrefined limit to the orbifold Euler characteristics of Hurwitz spaces of holomorphic maps. We discuss the geometrical meaning of our expansions in relation to quantum spectral curves and β‐ensembles of matrix models arising in refined topological string theory.     

Control of surface charge for high‐fidelity nanostructuring of materials

The universal problem of surface charging during focused ion milling has been fully resolved using a flood‐gun approach based on simultaneous co‐illumination with a UV light‐emitting diode (LED). Non‐distorted as‐designed nano‐patterns were milled using Ga⁺ ions on dielectric materials which charge up strongly. Deep‐UV (250–280 nm) LED co‐illumination during the ion beam milling fully discharges optically the surface under standard Ga⁺ ion‐milling conditions. Photo‐ionization of electrons trapped at the sub‐surface defects to the free vacuum state is a key to the phenomenon ( nm corresponds to a photon energy  eV). The method is applicable as a solution to other charging problems where electrons (primary or secondary) and their spatial redistribution affect nanofabrication or imaging.