Eco friendly synthesis of fluorescent carbon dots for the sensitive detection of ferric ions and cell imaging

This study established a ferric ion (Fe³⁺) detection method as a result of the fluorescence quenching effect of Fe³⁺ on carbon dots (CDs). Specifically, we proposed, a green microwave synthesis route towards fluorescent CDs that requires only the brewer’s spent grain as starting materials. Transmission electron microscopy, X-ray diffraction, Fourier-transform infrared spectra and X-ray photoelectron spectroscopy were performed to investigate the CDs characteristic: morphology, size distribution, functional groups, and composition, respectively. The experimental results, which were run under optimal experimental conditions, indicated that the fluorescence intensity and concentration of Fe³⁺ were within the desired linear range (0.3–7 μM). The detection limit of this assay towards Fe³⁺ was 95 nM. The proposed method showed significant selectivity with respect to interfering ions. We evaluated the potential application of this method with tap water, lake water and fetal bovine serum as real samples. Additionally, the CDs could be served as superior bioimaging probes in Hela cells as a result of their excellent optical stability and good biocompatibility. In a word, the present study provides a new idea for CDs derived from the waste of agricultural products for detecting food or environmental contaminants and cell imaging.     

Inner filter effect (IFE) as a simple and selective sensing platform for detection of tetracycline using milk-based nitrogen-doped carbon nanodots as fluorescence probe

A simple, selective, and sensitive turn-off fluorescent assay for detecting of tetracycline in pharmaceutical dosage form based on inner filter effect (IFE) sensing platform has been described. In this IFE sensing strategy, N-doped carbon dots (CDs) were prepared by one-pot solvothermal synthesis using milk as a precursor and were directly used as a fluorophore in IFE. The prepared CDs were characterized by common spectroscopic and microscopic techniques. The CDs exhibited excitation-wavelength dependent emission with 10% as the fluorescence quantum yield. The fluorescence of CDs was decreased in correlation to the addition of absorber (tetracycline), as the excitation spectrum of the fluorophore (CDs) matches the absorption spectrum of the absorber. The present IFE-based sensing platform showed a good linear relationship from 2.0 µM to 200 µM (R² = 0.9960) and provided a detection limit of 0.6 µM (signal-to-noise ratio of 3). Additionally, the cytotoxic effects of CDs were determined using normal healthy male Balb/C mice model treated with various doses of CDs and at the end of the study, no mortality or even no sign of toxicity was observed at oral doses of 100 and 200 mg/kg CDs in all treated animals. The proposed nanoprobe assay is a free from interferences, low-cost, biocompatible, and accurate for the detection of tetracycline in pharmaceutical formulation.     

Cu–N Dopants Boost Electron Transfer and Photooxidation Reactions of Carbon Dots

The broadband light‐absorption ability of carbon dots (CDs) has inspired their application in photocatalysis, however this has been impeded by poor electron transfer inside the CDs. Herein, we report the preparation of Cu–N‐doped CDs (Cu‐CDs) and investigate both the doping‐promoted electron transfer and the performance of the CDs in photooxidation reactions. The Cu–N doping was achieved through a one‐step pyrolytic synthesis of CDs with Na₂[Cu(EDTA)] as precursor. As confirmed by ESR, FTIR, and X‐ray photoelectron spectroscopies, the Cu species chelates with the carbon matrix through Cu–N complexes. As a result of the Cu–N doping, the electron‐accepting and ‐donating abilities were enhanced 2.5 and 1.5 times, and the electric conductivity was also increased to 171.8 μs cm^?1. As a result of these enhanced properties, the photocatalytic efficiency of CDs in the photooxidation reaction of 1,4‐dihydro‐2,6‐dimethylpyridine‐3,5‐dicarboxylate is improved 3.5‐fold after CD doping.     

Carbon dots-peroxyoxalate micelle as a highly luminous chemiluminescence system under physiological conditions

Chemiluminescence (CL) has been widely used for bioanalysis owing to its high sensitivity, low background and simplicity. However, most of the CL systems need acidic/alkaline conditions or organic solvent to enhance their luminescent efficiency, and the non-physiological conditions can usually lead to the misfunction of biomolecules during biosensing. Herein, we report a highly luminous CL system under physiological conditions based on carbon dots-bis(2-carbopentyloxy-3,5,6-trichlorophenyl) oxalate (CDs-CPPO) micelles, and further used it in biosensing application. In the CL system, the amphiphilic surfactant packed CPPO and hydrophobic CDs together to form CDs-CPPO micelles. Such micelles solution not only isolated the CPPO from water to prevent its hydrolysis but also made the close proximity between CPPO and CDs, thus significantly enhancing the CDs quantum yield. The CL quantum yield was calculated to be 5.26 × 10⁻⁴ einsteins/mol, about 200-fold higher than that of the most commonly used luminol CL system. The oxidases (e.g., glucose oxidase) were tested to be susceptible to the organic solvent and non-physiological pH. Hence, the CL system was used for the detection of oxidase substrates (exemplified by glucose) in serum samples, and the limit of detection was as low as 8.4 nmol/L. The highly luminous CL system that can work under physiological conditions is promising for biosensing applications     

Synthesis and characterization of CDs/Al2O3 nanofibers nanocomposite for Pb2+ ions adsorption and reuse for latent fingerprint detection

This study reports a new approach of preparation of carbon dots coated on aluminum oxide nanofibers (CDs/Al₂O₃NFs) nanocomposite and reusing the spent adsorbent of lead (Pb²⁺) ions loaded adsorbent (Pb²⁺-CDs/Al₂O₃NFs) nanocomposite for latent fingerprint detection (LFP) after removing Pb²⁺ ions from aqueous solution. CDs/Al₂O₃NFs nanocomposite was prepared by using CDs and Al₂O₃NFs with adsorption processes. The prepared nanocomposite was then characterized by using UV–visible spectroscopy (UV–visible), Fourier transforms infrared spectroscopy (FTIR), Fluorescence, X-ray diffraction pattern (XRD), scanning electron microscope (SEM), Transmission electron microscopy (TEM), Energy-dispersive X-ray spectroscopy (EDS), Zeta potential, X-ray photoelectron spectroscopy (XPS). The average size of the CDs was 51.18 nm. The synthesized CDs/Al₂O₃NFs nanocomposite has proven to be a good adsorbent for Pb²⁺ ions removal from water with optimum pH 6, dosage 0. 2 g/L. The results were best described by the Freundlich Isotherm model. The adsorption capacity of CDs/Al₂O₃NFs nanocomposite showed the best removal of Pb²⁺ ions with q_m = (177. 83 mg/g), when compared to the previous reports. This adsorption followed the pseudo-second order kinetic model. ΔG and ΔH values indicated spontaneity and the endothermic nature of the adsorption process. CDs/Al₂O₃NFs nanocomposite therefore showed potential as an effective adsorbent. The data were observed from adsorption–desorption after 6 cycles which showed good adsorption stability and re- usability of CDs/Al₂O₃NFs nanocomposite. Furthermore, the spent adsorbent of Pb²⁺-CDs/Al₂O₃NFs nanocomposite has proven to be sensitive and selective for LFP detection on various porous substrates. Hence Pb²⁺-CDs/Al₂O₃NFs nanocomposite can be reused as a good fingerprint labelling agent in LFP detection so as to avoid secondary environmental pollution by disposal of the spent adsorbent.     

pH effects on the rate of heterogeneous electron transfer across a fluorine doped tin oxide/monolayer interface

Spontaneously adsorbed monolayers of [Ru(bpy)₂PIC](PF₆)₂ have been formed on fluorine doped tin oxide macro- and microelectrodes, bpy is 2,2′-bipyridyl and PIC is 2-(4-carboxyphenyl)imidazo[4,5-f][1,10]phenanthroline. These monolayers exhibit well-defined, almost ideal electrochemical responses over a wide range of voltammetric scan rates. The formal potential of the Ru^2+/3+ process shifts by less than 30 mV upon immobilization suggesting that the monolayers are well solvated. Significantly, chronoamperometry, conducted on a microsecond timescale, reveals that protonation of the PIC bridging ligand modulates the rate of interfacial electron transfer. The heterogeneous electron transfer rate constant, measured at an overpotential of +50 mV, decreases from 7.0 ± 1.1 × 10⁵ to 0.7 ± 0.1 × 10⁵ s⁻¹ as the pH of the supporting electrolyte is increased from 1.7 to 9.3. These observations are consistent with the redox mechanism occurring via a heterogeneous electron transfer process, the rate of PIC which depends on the energy difference between the metal dπ-orbitals and the lowest unoccupied molecular orbital (LUMO) of the bridge. Protonation of the bridging ligand decreases this energy gap, resulting in an overall increase in the rate of the redox reaction. Significantly, despite the close proximity of the luminophores to a conducting surface, the monolayers remain luminescent suggesting that the electronically excited state is only weakly coupled to the electrode surface. This is consistent with bipyridyl as the site of the excited state in the metal complex.     

Time-dependent Phosphorescence Color of Carbon Dots in Binary Salt Matrices through Activations by Structural Confinement and Defects for Dynamic Information Encryption

The emergence of time-dependent phosphorescence color (TDPC) materials has taken information encryption to high-security levels. However, due to the only path of exciton transfer, it is almost impossible to obtain TDPC for chromophores with a single emission center. Theoretically, in inorganic-organic composites, the exciton transfer of organic chromophores depends on the inorganic structure. Here, we assign two structural effects to inorganic NaCl by metal (Mg²⁺ or Ca²⁺ or Ba²⁺) doping, which triggers the TDPC performance of carbon dots (CDs) with a single emission center. The resulting material is used for multi-level dynamic phosphorescence color 3D coding to achieve information encryption. The structural confinement activates the green phosphorescence of CDs; while the structural defect activates tunneling-related yellow phosphorescence. Such simply doped inorganic matrices can be synthesized using the periodic table of metal cations, endowing chromophores with tremendous control over TDPC properties. This demonstration extends the design view of dynamic luminescent materials.     

Symmetry‐Breaking Charge‐Transfer Chromophore Interactions Supported by Carbon Nanodots

Carbon dots (CDs) and their derivatives are useful platforms for studying electron‐donor/acceptor interactions and dynamics therein. Herein, we couple amorphous CDs with phthalocyanines (Pcs) that act as electron donors with a large extended π‐surface and intense absorption across the visible range of the solar spectrum. Investigations of the intercomponent interactions by means of steady‐state and pump‐probe transient absorption spectroscopy reveal symmetry‐breaking charge transfer/separation and recombination dynamics within pairs of phthalocyanines. The CDs facilitate the electronic interactions between the phthalocyanines. Thus, our findings suggest that CDs could be used to support electronic couplings in multichromophoric systems and further increase their applicability in organic electronics, photonics, and artificial photosynthesis.     

Green synthesis of fluorescent carbon dots from Kumquat (Fortunella margarita) for detection of Fe3+ ions in aqueous solution

In this study, kumquat was first time used for synthesizing carbon dot structures (CDs) with the hydrothermal method. These newly synthesized CDs was characterized structurally and optically. The ion sensor application of the new CDs was carried out using 20 different metal ions. It was observed that CDs have high selectivity only for Fe³⁺ ions among the metal ions studied. Detection limit for Fe³⁺ ions was calculated as 0.70 µM. The results showed that these new CDs are highly selective against Fe³⁺ ions and have a very short response time such as 0.5 min. The Fe³⁺ ions selectivity of CDs was tested on real (tap water) samples. The results exhibited that this new CDs, obtained with green synthesis from Kumquat fruit without using chemical agents in one-pot simple and economical process, can be used as fluorometric sensor for detection of Fe³⁺ ions with high selectivity and sensitivity, low detection limit and rapid response time.

     

Symmetry-Breaking Charge-Transfer Chromophore Interactions Supported by Carbon Nanodots

Carbon dots (CDs) and their derivatives are useful platforms for studying electron-donor/acceptor interactions and dynamics therein. Herein, we couple amorphous CDs with phthalocyanines (Pcs) that act as electron donors with a large extended π-surface and intense absorption across the visible range of the solar spectrum. Investigations of the intercomponent interactions by means of steady-state and pump-probe transient absorption spectroscopy reveal symmetry-breaking charge transfer/separation and recombination dynamics within pairs of phthalocyanines. The CDs facilitate the electronic interactions between the phthalocyanines. Thus, our findings suggest that CDs could be used to support electronic couplings in multichromophoric systems and further increase their applicability in organic electronics, photonics, and artificial photosynthesis.     

Breaking the barrier to fast electron transfer

A study of the electron transfer for a non-glycosylated redox variant of GOx is reported, immobilised onto an electrode via a polyhistidine tag. The non-glycosylated variant allows the enzyme to be brought closer to the electrode, and within charge transfer distances predicted by Marcus' theory. The enzyme-electrode-hybrid shows direct very fast reversible electrochemical electron transfer, with a rate constant of ~ 350 s^− 1 under anaerobic conditions. This is 2 orders of magnitude faster than the enzyme-free flavin adenine dinucleotide (FAD). These results are discussed in the context of the conformation of FAD in the active site of GOx. Further data, presented in the presence of oxygen, show a reduced electron transfer rate (~ 160 s^− 1) that may be associated with the oxygen interaction with the histidines in the active site. These residues are implicated in the proton transfer mechanism and thus suggest that the presence of oxygen may have a profound effect in attenuating the direct electron transfer rate and thus moderating ‘short-circuit’ incidental electron transfer between proteins.     

Intramolecular photoinduced electron transfer in a ruthenium polypyridyl functionalised β-cyclodextrin capped with a hydroxo bridged Cu(II) dimer

The synthesis of a novel donor–acceptor system comprising a ruthenium polypyridyl unit covalently linked to the secondary face of β-cyclodextrin which has a hydrxy bridged dinuclear copper(II) moiety on its primary face is described and the spectroscopic, electrochemical and photophysical properties of this complex are outlined. Photophysical studies demonstrate evidence for photoinduced electron transfer from the excited ruthenium to the copper centre. The rate of electron transfer, was estimated from luminescence lifetime studies to be 1.86 × 10⁻⁶ s⁻¹. The parent ruthenium polypyridyl functionalized β-cyclodextrin complex binds to both Cu(II) and Zn(II) in alkaline aqueous solution and the affects of these cations on the luminescence intensity of this complex is explored and compared with the photophysics of the isolated supramolecular complex. Whereas Cu(II) statically quenches the ruthenium centre, Zn(II) has little effect. This work suggests luminescent CD complexes, with long-lived luminophores may have value in metal ion sensing.     

Photoinduced electron transfer in a triarylamine-organoboron-Ru(2,2′-bipyridine)32+ compound

Long-range electron transfer reactions play a key role in biological photosynthesis, and they are likely to play an important role for future artificial photosynthetic endeavors as well. The possibility to control the rates for long-range electron transfer with external stimuli is of particular interest in this context. In the work presented herein, we explored a donor–bridge–acceptor compound in which intramolecular electron transfer from a triarylamine donor to a photoexcited Ru(bpy)₃²⁺ (bpy = 2,2′-bipyridine) acceptor occurs across an organoboron bridge over a distance of approximately 22 Å. Fluoride has a high binding affinity to the organoboron bridge in apolar solutions, and the resulting organofluoroborate has a significantly different electronic structure. We explored to what extent the change from an electron-deficient organoboron wire to an electron-rich organofluoroborate bridge affects long-range electron transfer between the distant triarylamine donor and the Ru(bpy)₃²⁺ acceptor.     

Gold nanoparticles stabilized by modified halloysite nanotubes for catalytic applications

A highly sustainable prototype of a flow system based on gold nanoparticles (4.2 nm) supported on thiol‐functionalized halloysite nanotubes (HNTs) was developed for catalytic applications. The catalytic performances were evaluated using the reduction of 4‐nitrophenol to 4‐aminophenol as a model system. Under the best experimental conditions (0.0001 mol%, 1.97 × 10^?8 mg of Au nanoparticles), an impressive apparent turnover frequency value up to 2 204 530 h^?1 was achieved and the halloysite‐based catalyst showed full recyclability even after ten cycles. The high catalytic activity confirms the importance of the use of HNTs as support for Au nanoparticles that can exert a synergistic effect both as medium for transfer of electrons from borohydride ions to 4‐nitrophenol and by modulating interfacial electron transfer dynamics. With the application of flow technology, the obtained heterogeneous HNT@Au catalyst was fully recovered and reused for at least one month.     

Effects of local matrix environment on the spectroscopic properties of ensemble to single-particle level carbon dots

Carbon dots(CDs), because of their unique properties, are being rapidly developed as important luminescent materials for imaging, sensing, and use in photonic devices. However, most of the reported fundamental properties of the CDs are results of investigations conducted in the solution state, which may be completely different from those conducted in the solid state. In this work, we study the luminescence properties, photostability, and the dynamics of CDs in different matrix environments, from...     

Yellow emissive carbon dots in ludox silica matrix with anticancer activity for enhanced imaging of developed sweat latent fingermarks

The recognition of fingermarks plays a vital role during a criminal investigation. In the current scenario, fluorescent nano-powders emerged as a potential candidate for latent fingermark detection. We pioneer the use of microwave technology for the synthesis of carbon dots (CDs) with the cationic surfactant (cetylpyridinium chloride). The surfactant-derived CDs exhibit yellow fluorescence and emission at 545 nm with high quantum yield of (QY～34%). The prepared CDs also demonstrated amphiphilic properties. These luminous CDs were combined with ludox HS-30 to develop fluorescent hybrid nano-powders for the detection of sweat latent fingermarks on a non-porous surface. The ludox@CDs accumulate particle size 11.36 ± 1.235 nm and surface area 111 cm³/g^?1. The fluorescent hybrid nano-powders emerged to be successful in creating high contrast and accurate latent fingermark images. Furthermore, cytotoxicity studies on breast cell lines (fR-2 and MCF-7) were conducted by using ludox@CDs. The results revealed that ludox@CDs were less toxic and biocompatible in comparison to the commercialized dusting reagents. Fortunately, ludox@CDs demonstrated anticancer efficacy against MCF-7 breast cancer cell lines. Thus, our findings herald a new age for fluorescent hybrid nano-powders in criminal investigation and biomedical applications.     

Rapid and Large‐Scale Production of Multi‐Fluorescence Carbon Dots by a Magnetic Hyperthermia Method

The intrinsic low yield of carbon dots (CDs) is a barrier that limits practical application. Now, a magnetic hyperthermia (MHT) method is used to synthesize fluorescent CDs on a large scale (up to 85 g) in one hour (yield ca. 60 %). The reaction process is intensified by MHT since the efficient heating system enhances the energy transfer. CDs with blue, green, and yellow luminescence are synthesized by using carbamide and citrate with three different cations (Zn²⁺, Na⁺, K⁺), respectively. The CDs exhibit bright fluorescence under UV light and show excellent monodispersity and solubility in water. The alternation of photoluminescence (PL) emissions of these CDs is probably due to the difference in particle sizes and surface state. A bar coating technique is used to construct large‐area emissive polymer/CDs films. CDs can insert themselves into the polymer chains by hydrogen bonding and electrostatic interactions. Wound healing efficiency can be enhanced by the Zn‐CDs/PCL nanofibrous scaffold.     

Calorimetric investigations of luminescent films polycarbonate (PC) doped with europium complex [Eu(TTA)<Subscript>3</Subscript>(H<Subscript>2</Subscript>O)<Subscript>2</Subscript>]

Polymers doped with rare earth complexes are advantaged in film production for many applications in the luminescent field. In this luminescent polycarbonate (PC) films doped with diaquatris(thenoyltrifluoroacetonate)europium(III) complex [Eu(TTA)₃(H₂O)₂] were prepared and their calorimetric and luminescent properties in the solid state are reported. The thermal behavior was investigated by utilization of differential scanning calorimetry (DSC) and thermogravimetry (TG). Due of the addition of rare earth [Eu(TTA)₃(H₂O)₂] into PC matrix, changes were observed in the thermal behavior concerning the glass transition and thermal stability. Characteristic broadened narrow bands arising from the ⁵D₀ → ⁷F_J transitions (J = 4−0) of Eu³⁺ ion indicate the incorporation of the Eu³⁺ ions in the polymer. The luminescent films show enhancement emission intensity with an increase of rare earth concentration in polymeric matrix accompanied by decrease in thermal stability.     

Light-induced electron transfer reactions

The reactions of the luminescent excited states of the polypyridine-ruthenium(II) complexes (^*RuL₃²⁺) with electron acceptors and donors are discussed. These electron transfer reactions convert the excited state into RuL₃³⁺ and RuL₃⁺, respectively. The former ruthenium complex is a more powerful oxidant and the latter is a more powerful reductant than the excited state itself. Some applications of these complexes in the conversion and storage of solar energy are presented. Theoretical models for electron transfer reactions are described and the implications of these models for the quenching and back electron transfer reactions are discussed. It is pointed out that the exploitation of the inverted region may provide a useful means of slowing down back electron transfer reactions.     

Quenching dynamics study on photoinduced excited triplet duroquinone by TEMPO in 1,2-propandiol

Chemically induced dynamic electron polarization (CIDEP) spectrum and transient absorptive spectrum are recorded in photolysis of duroquinone (DQ) in 1,2-propanodiol (PG). Durosemiquinone neutral radical DQH^• and PG ketyl radical \textCH₃[(\textC)\dot]\textOHCH₂\textOH{\text{CH}}_{3}{{{\dot{\text{C}}}\text{OHCH}}}_{2}{\text{OH}} are produced through hydrogen transfer reaction from PG to ³DQ*. When stable radical TEMPO is added to DQ/PG solution, photolysis results in CIDEP on TEMPO, which can be interpreted as a quartet precursor radical-triplet pair mechanism (QP-RTPM). There is competition between PG and TEMPO to quench ³DQ*. The CIDEP intensity of DQH^• decreases with the increase of TEMPO concentration. The quenching dynamics in photolysis of DQ/TEMPO/PG system is analyzed in detail. Based on the dynamics analysis and the measurement of the lifetime of ³DQ* by its transient absorbance decay, the quenching rate constant of ³DQ* by TEMPO in PG is obtained as 1.34 × 10⁷ L mol⁻¹ s⁻¹. This quenching rate constant is closely diffusion-controlled.