Corrosion inhibitive evaluation and DFT studies of 2-(Furan-2-yl)-4,5-diphenyl-1H-imidazole on mild steel at 1.0M HCl

A novel heterocyclic compound 2-(Furan-2-yl)-4,5-Diphenyl-1H-Imidazole (FDPI) was synthesized by a simple and cost effective one pot synthetic protocol and the structure of FDPI was confirmed by FT-IR, ¹H NMR and ¹³C NMR spectra. The corrosion inhibition activity of FDPI was investigated using gravimetric and electrochemical methods. It resulted a maximum inhibition efficiency of 95.84% at 10 mmolL⁻¹ concentrations of FDPI. The excellent inhibition efficiency is reasoned as the adsorption of FDPI on the mild steel surface as a protective layer immersed in the 1 ​M HCl. The adsorbed layer obeys Langmuir adsorption isotherm and the ΔG^o_ads values of FDPI suggested that process involves physisorption. The polarization curves showed that the FDPI behaves as a mixed type inhibitor. Surface morphology studied by SEM confirmed the formation of a protective film of FDPI on the mild steel surface. The computational studies using DFT have been analyzed for the FDPI to determine the HOMO-LUMO energy gap.     

A sustainable method of mitigating acid corrosion of mild steel using jackfruit pectin (JP) as green inhibitor: Theoretical and electrochemical studies

This study is attempted to develop a green corrosion inhibitor from a waste material of Jack fruit (Artocarpus heterophyllus). This method is therefore quite valuable to health, environment, and economic point of view. Pectin is isolated from the jackfruit peel waste using 0.05 ?N oxalic acid and used as an inhibitor for mild steel corrosion in acidic environment as it is highly water soluble. 250–1000 ?ppm of pectin was used in this study at a temperature range of 303–323 ?K. The protection efficiency of jack fruit pectin (JP) in 0.5 ?M HCl was evaluated by conventional weight loss and electrochemical techniques. The potentiodynamic polarization results revealed that JP could effectively reduce the corrosion of mild steel in acidic medium at 1000 ?ppm concentration with an inhibition efficiency of 89.75% and corrosion rate of 2.392 mpy. The mixed type behavior of the inhibitor is identified from Tafel polarization studies. Electrochemical impedance spectroscopy (EIS) measurements suggest that the corrosion inhibition process is kinetically controlled. adsorption and kinetic behavior of the inhibitor also have been studied. Surface manifestations were followed using FESEM and AFM techniques. DFT calculations and Monte Carlo simulations were also carried out to corroborate the experimental results with theoretical outputs and succeeded to a great extent.     

Experimental,DFT studies and molecular dynamic simulation on the corrosion inhibition of carbon steel in 1 M HCl by two newly synthesized 8-hydroxyquinoline derivatives

In the present work, two new 8-hydroxyquinoline derivatives namely, 5-(((2-hydroxybenzylidene)amino)methyl) 8-hydroxyquinoline [HBMQ] and 5-(((4-chlorobenzylidene)amino)methyl) 8-hydroxyquinoline [CBMQ] were synthesized and investigated as corrosion inhibitors against the dissolution of carbon steel (C38 steel) in 1 M HCl. These compounds were obtained with high yield, and their structures were characterized by nuclear magnetic resonance spectroscopy (NMR) and elemental analysis. Gravimetric, electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PDP), and surface morphology analyses utilizing scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) were used to quantify inhibitory performance. The adsorption process of inhibitory compounds was then demonstrated using quantum mechanics approaches such as Density Functional Theory (DFT) and Molecular Dynamic Simulation (MD). Based on EIS results, the investigated derivatives effectively inhibit the degradation of C38 steel over the entire concentration range with a maximum efficiency of 91.9% and 88.0% for [CBMQ] and [HBMQ], respectively, at 10^?3 M. In addition, the PDP studies revealed that [HBMQ] and [CBMQ] compounds acted according to a mixed-type mechanism. Moreover, the adsorption mechanism follows the Langmuir isotherm model. The quantum theoretical study by DFT and MD simulation confirmed the experimental results.     

Electropolymerized coatings of poly(o‐anisidine) and poly(o‐anisidine)‐TiO2 nanocomposite on aluminum alloy 3004 by using the galvanostatic method and their corrosion protection performance

Poly(o‐anisidine) (POA) and poly(o‐anisidine)‐TiO₂ (POA‐TiO₂) nanocomposite coatings on aluminum alloy 3004 (AA3004) have been investigated by using the galvanostatic method. The electrosynthesized coatings were characterized by FT ‐ IR spectroscopy, XRD, SEM ‐ EDX and SEM. The corrosion protection performance of POA and POA‐TiO₂ nanocomposite coatings was investigated in the 3.5% NaCl solution by using potentiodynamic polarization technique and electrochemical impedance spectroscopy. The results show that the corrosion rate of the nanocomposite coatings is about 900 times lower than the bare AA3004 under optimal conditions. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis,characterization, corrosion inhibition of mild steel in HCl (0.5 N) solution and solid‐state electrical conductivity of new Co(II), Ni(II), Cu(II) and Zn(II) complexes

This work consists of a study of the corrosion‐inhibiting and semiconducting properties of new binuclear Co(II), Ni(II), Cu(II) and Zn(II) complexes with a Schiff base, H₂L, obtained from the 2:1 M condensation of salicylaldehyde and o‐dianisidine, respectively. Elemental, spectral and thermal analyses were used to characterize these complexes. The magnetic susceptibilities of these complexes were also determined. Weight loss, potentiodynamic polarization and scanning optical microscopy were the techniques used to investigate the efficiency of these new compounds as corrosion inhibitors. The antibacterial activity of the compounds was measured against sulfate‐reducing bacteria. It was found that inhibition occurs via the chemisorption of metal complexes on the steel surface. This absorption obeys the Langmuir adsorption isotherm model.     

Removal of Pb(II) from water samples using surface modified core/shell CdZnS/ZnS QDs as adsorbents: Characterization,adsorption, kinetic and thermodynamic studies

This research presents aqueous colloidal method to synthesize CdZnS/ZnS surface modified core/shell quantum dots (QDs) with capping agents 2-mercaptoacetic acid and 3-mercaptopropanoic acid. The QDs were characterized by the different analytical techniques. Using Plackett–Burman and Central composite designs, optimum conditions for the removal of Pb(II) from aqueous medium were developed: QDs (0.013 g) at pH 6.9, time of adsorption and desorption (20 min), temperature (61.1 °C) and dilution on 100 ppb standard solutions. Moreover, Freundlich models suggested that Pb(II) adsorption was favorable on the heterogeneous surface of QDs. The values of ΔG^° and ΔH^° (?59.26 KJ/mol.K) suggested the process was spontaneous and exothermic. The negative ΔS^° (?0.16 KJ/mol.K) indicates that the Pb(II) chemisorb on QDs. While, system follows the pseudo-second order rate equation which indicates that rate limiting step involves chemical reaction and could be influenced by the intraparticle/pore diffusion of Pb(II) ions with QDs. By using atomic absorption spectrophotometer, developed method was tested for Pb(II) removal from tap and ground water samples taken from the different districts of Karachi City. The % recovery for Pb(II) was found to be 96.4 % (tap water) and 94.8 % (ground water) with LOD = 0.1 ng mL^?1 and LOQ = 0.90 ng mL^?1.     

Synthesis,spectral, magnetic,electrochemical and kinetic studies of copper(II), nickel(II) and zinc(II) acetate complexes derived from phenol based ‘end-off’ ligands: Effect of p-substituents

A new class of symmetric, end-off, N-methyl piperazine armed binucleating ligands 2,6-bis(4-methyl piperazin-1-yl-methyl)-4-acetyl phenol (HL¹) and 2,6-bis[(4-methyl piperazin-1-yl-methyl)]-(4-methylcarboxy) phenol (HL²) were synthesized by the Mannich reaction. Their mononuclear and binuclear Cu(II), Ni(II) and Zn(II) complexes have been synthesized. These complexes were characterized by elemental analysis, infra-red and electronic spectral analysis. In the electronic spectra, the lower electron withdrawing nature of the C(O)CH₃p-substituent (HL¹) compared with the C(O)OCH₃p-substituent (HL²) of the phenolic ring causes a red shift in the LMCT-charge transfer band. The mononuclear Cu(II) complexes 1 and 7 have a magnetic moment value close to the spin only value with four hyperfine EPR signals. The binuclear Cu(II) complexes 4 and 10 illustrate an antiferromagnetic interaction (μ_eff 1.56 and 1.55 BM) at 298 K with a broad EPR signal. A variable temperature magnetic moment study of the binuclear copper(II) complexes shows that the extent of antiferromagnetic coupling increases in the order: CHO [K. Shanmuga Bharathi, A. Kalilur Rahiman, K. Rajesh, S. Sreedaran, P.G. Aravindan, D. Velmurugan, V. Narayanan, Polyhedron 25 (2006) 2859] < C(O)CH₃ < C(O)OCH₃ (−2J values 134 [Shanmuga Bharathi et al., mentioned above], 149 and 158 cm⁻¹, respectively). The mononuclear Ni(II) complexes 2 and 8 are square planar and diamagnetic. The six coordinated binuclear Ni(II) complexes 5 and 11 show a magnetic moment value of 2.96 and 2.95 BM, respectively. Electrochemical studies of the complexes reveal that all the mononuclear complexes show a single irreversible one-electron transfer reduction wave and the binuclear complexes show two irreversible one-electron transfer reduction waves in the cathodic region. There is an anodic shift in the reduction of the metal centres when the electron withdrawing nature of the p-substituent of the phenolic ring increases. The catecholase activity of the mono and binuclear copper(II) complexes, using pyrocatechol as a model substrate, and the hydrolysis of 4-nitrophenyl phosphate using the mono and binuclear copper(II), nickel(II) and zinc(II) complexes as catalysts showed that the binuclear complexes have higher rate constant values than those of the corresponding mononuclear complexes. A comparison of the spectral, electrochemical and magnetic behaviour of the complexes derived from the ligands is discussed on the basis of the substituent at the para position of the phenolic ring.     

New anti-corrosion inhibitor (3ar,6ar)-3a,6a-di-p-tolyltetrahydroimidazo[4,5-d]imidazole-2,5(1 h,3h)-dithione for carbon steel in 1 M HCl medium: gravimetric,electrochemical, surface and quantum chemical analyses

The inhibition of (3ar,6ar)-3a,6a-di-p-tolyltetrahydroimidazo[4,5-d]imidazole-2,5(1 h,3h)-dithione (TTHIIDT) for carbon steel was full characterized in a 1 M hydrochloride acid environment at various inhibitor concentrations and temperatures by the gravimetric, electrochemical, surface and quantum chemical analyses. The obtained results confirmed that the inhibition efficiency of TTHIIDT was over 95–97% and nearly stable in the rise of temperature and concentration; TTHIIDT was mixed type inhibitor and effectively influenced both anodic and cathodic corrosion reactions; a protective hydrophobic thin layer of this inhibitor on the carbon steel surface is more stable and non soluble in 1 M HCl medium; this inhibitor adsorbed endothermically on the carbon steel surface by the chemical and physical adsorption processes. The quantum chemical calculations supported the experimental results and showed that the inhibition efficiency is depends on the structure of inhibitor.     

DFT calculations, DRIFT spectroscopy and kinetic studies on the hydrolysis of isocyanic acid on the TiO2-anatase (1 0 1) surface

The co-adsorption of isocyanic acid (HNCO) and water (H₂O) and their reaction to ammonia and carbon dioxide on the anatase phase of TiO₂ were studied with ab initio density functional theory (DFT) calculations using a cluster model as well as with in situ DRIFTS investigations and kinetic experiments. We found that isocyanic acid can in principle adsorb both molecularly and dissociatively on the TiO₂(1 0 1) surface, but the moment at which water gets involved in the process, is vital for determining the further course of the surface reaction. In the absence of water, it was found that HNCO can adsorb in molecular form on the TiO₂ surface. Assuming this case to be the first step of the HNCO hydrolysis, the surface HNCO rearranges into an intermediate complex with a modified NCO skeleton. After decarboxylation water attacks the complex from the gas phase and ammonia is finally formed.

However, when water is present at the beginning of the hydrolysis reaction, it immediately attacks the NCO group present at the surface, yielding a carbamic acid complex, which is further transformed into a carbamate complex. After decarboxylation an NH₂ group remains at the surface. Finally, NH₃ is formed by hydrogen transfer from molecularly adsorbed water at a neighboring titanium center and the hydrolysis reaction is completed.

Since water is always present in diesel exhaust gas, only the second mechanism is relevant under practical conditions. Moreover, the calculated energy barrier is lower for the second mechanism compared to the first reaction pathway. The comparison between the sum of the theoretical vibrational spectra of the reaction intermediates with the in situ DRIFT spectra also strongly supports the accuracy of the second reaction pathway. The experimental investigation of the kinetics of the HNCO hydrolysis on TiO₂-anatase revealed a second order reaction—first order with respect to HNCO and first order with respect to water, which can only be reconciled with the second mechanism.     

Crystal structure,electrochemical and photochemical studies of the trans-[Fe(cyclam)(NO)Cl]Cl2 complex (cyclam = 1,4,8,11-tetraazacyclotetradecane)

The trans-[Fe(cyclam)(NO)Cl]Cl₂ complex was synthesized by the reaction of cis-[Fe(cyclam)Cl₂]Cl with NO gas. The X-ray structure of the complex showed that the [Fe–NO] moiety is linear, consistent with the NO⁺ character of the nitric oxide ligand. This suggestion was reinforced by the IR data, which showed the νNO at 1888 cm⁻¹. The cyclic voltammogram of the trans-[Fe(cyclam)(NO)Cl]²⁺ complex presented three electrochemical processes at −0.70, 0.08 and 0.40 V versus Ag/AgCl. The first and last redox processes are centered at the NO ligand, whereas the second is characteristic of the generated aqua species, trans-[Fe(cyclam)Cl(H₂O)]²⁺. Upon irradiation at 330 nm, pH 3.4, the title complex releases the NO moiety with the concomitant generation of the trans-[Fe(cyclam)(H₂O)Cl]⁺ complex as suggested by electronic and IR spectroscopy as well as by cyclic voltammetry technique.     

Synthesis, characterization and electrochemical studies of the heterometallic diclusters [{Fe2(μ-CO)(CO)6(μ-PPh2)Au}2(diphosphine)] (diphosphine=dppm, dppip, dppe, dppp)

Treatment of [(ClAu)₂(diphosphine)] {diphosphine=bis(diphenylphosphino)methane (dppm), bis(diphenylphosphino)isopropane (dppip), 1,2-bis(diphenylphosphino)ethane (dppe), 1,3-bis(diphenylphosphino)propane (dppp)} with two equivalents of the anion [Fe₂(μ-CO)(CO)₆(μ-PPh₂)]⁻ in the presence of TlBF₄ gives the new heterometallic diclusters [{Fe₂(μ-CO)(CO)₆(μ-PPh₂)Au}₂(diphosphine)] that have been isolated and characterized. Their ³¹P-NMR spectra show different patterns as a function of the diphosphine ligand. The electrochemical behavior of these compounds has been investigated and compared with that of the mono- [Fe₂(μ-CO)(CO)₆(μ-PPh₂)(μ-AuPPh₃)] and tricluster [{Fe₂(μ-CO)(CO)₆(μ-PPh₂)Au}₃(triphos)] derivatives.     

Synthesis,spectral characterization,electrochemical studies and catalytic properties in Suzuki–Miyaura coupling reactions of the mononuclear PdII,trinuclear PdII(BPh2)2 and RuII?PdII?RuII type complexes containing 4‐amino‐1‐benzyl piperidine and phenyl groups

The ligand containing the 4‐amino‐1‐benzyl piperidine group, N, N′‐(4‐amino‐1‐benzyl piperidine)‐glyoxime, (LH₂) (1) was prepared from 4‐amino‐1‐benzyl piperidine with anti‐dichloroglyoxime at ? 15 °C in absolute Tetrahydrofuran (THF). In the trinuclear [Pd(L)₂Ru₂(phen)₄](ClO₄)₂ (4) and [Pd(L)₂Ru₂(bpy)₄](ClO₄)₂ (5) metal complexes, the Pd^II ion centered into the main oxime core by the coordination of the imino groups while the two Ru^II ions coordinated dianionic oxygen donors of the oxime groups and linked to the ligands of 1,10‐phenanthroline and 2,2′‐bipyridine. The mono and trinuclear metal complexes were characterized by elemental analyses, FT‐IR, UV–vis, ¹H and ¹³C‐NMR spectra, magnetic susceptibility measurements, molar conductivity, cyclic voltammetry, mass spectra, X‐ray powder techniques and their morphology by SEM measurements. The cyclic voltammetric results show that the cathodic peak (E_pc) potential of (3) shifts towards more positive values compared with that of (2) as a result of the BPh₂⁺‐bridged complex formation. The Suzuki–Miyaura reaction was used to investigate their activity as catalyst either prepared in‐situ or from well‐defined complexes. Copyright © 2008 John Wiley & Sons, Ltd.     

Comment on “Theoretical studies on the ground states in [M(terpyridine)2] and [M(4-(4-(t-butyl)phenyl)terpyridine)2] (M = Fe, Ru, Os) and excited states in [Ru(terpyridine)2] using density functional theory”

The nature of the first excited state of [Fe(terpyridine)₂]²⁺ has been reinvestigated. In contrast to previous findings, it is metal-to-ligand charge transfer in nature, thus fitting in the series of the Ru and Os complexes.