Synthesis and inhibition corrosion effect of two thiazole derivatives for carbon steel in 1 ​M HCl

Inhibition of C38 carbon steel corrosion by 4-methyl-3-phenyl-2(3H)-thiazolethione (TO1) and 4-methyl-2-(methylthio)-3- phenylthiazol-3-ium (ST1) in 1 ​M HCl was investigated by weight loss and electrochemical methods. All of the data obtained reveal that the two compounds act as good inhibitors in this media. At optimized concentration TO1 and ST1 showed the highest inhibition efficiency of 98.8% (2.10⁻⁴ ​M) and 93.86% (10⁻³ ​M) respectively. Polarization curves show that inhibitor molecules act as mixed type inhibitors. The impedance study showed that an increase in the concentration of the two inhibitors is accompanied by an increase in polarization resistance and a decrease in double layer capacitance. The Langmuir isotherm very well describes the adsorption of inhibitors to the surface of the corroding metal and the thermodynamic parameters showed that the adsorption of the two compounds was strong and chemical nature. X-ray photoelectron spectroscopy (XPS) confirms and describes the absorption of inhibitors under investigation on the metal surface.     

The litchi (Litchi Chinensis) peels extract as a potential green inhibitor in prevention of corrosion of mild steel in 0.5 M H2SO4 solution

The corrosion inhibition of mild steel in 0.5 M H₂SO₄ solution by the extract of litchi peel (Litchi chinensis) was studied by weight loss method, potentiodynamics polarization and electrochemical impedance spectroscopy (EIS). The results show that the litchi peels extract acts as mixed-type inhibitor. The inhibition of corrosion is found to be due to adsorption of the extract on metal surface, which is in conformity with Langmuir’s adsorption isotherm. UV–Vis, Fourier transform infrared (FT-IR) spectroscopy and Scanning electron microscopy (SEM) studies confirm that the inhibition of corrosion of mild steel occurs through adsorption of the inhibitor molecules.     

Evaluation of the inhibitive effect of essential oil of Lavandula multifida L., on the corrosion behavior of C38 steel in 0.5 M H2SO4 medium

The essential oil of the aerial parts of Lavandula multifida L., collected in Errachidia region (three samples) in southeast Morocco, was extracted by hydrodistillation and analyzed by GC and GC-MS. The oil was predominated by carvacrol (57.9–59.0%). L. multifida oil was tested as corrosion inhibitor of C38 steel in 0.5 M H₂SO₄ using weight loss measurements, electrochemical polarization, and EIS methods. The results obtained by measurements of weight loss showed that inhibition efficiency increases with inhibitor concentration to attain 72.2% at 2 g/l of oil at 298 K. Polarization curves revealed that L. multifida oil acts as mixed type inhibitor. The temperature effect on the corrosion behavior of steel in 0.5 M H₂SO₄ without and with the inhibitor at 2 g/l was studied in the temperature range from 303 and 343 K. The adsorption of inhibitor on the C38 steel surface was found to be a spontaneous process and to obey Langmuir’s adsorption isotherm. The associated activation energy has been determined.     

Applicability of winged bean extracts as organic corrosion inhibitors for reinforced steel in 0.5 ​M HCl electrolyte

Corrosion inhibition properties of winged bean (WB) extracts on reinforced steel in 0.5 ?M HCl solution was studied through experimental and theoretical calculation methods. The electrochemical studies suggested that inhibition efficiency increased with increasing concentration of WB extracts up to 95%. Nyquist diagrams revealed an increase in the charge transfer resistance values and a decrease in the constant phase element as the concentration of WB extracts were increased. The potentiodynamic polarization results revealed that WB extracts behave as mixed-type inhibitors, which physically adsorbed onto the reinforced steel surface. Effect of temperature study demonstrated that the corrosion resistance behaviour of WB extracts decreased with an increase in temperature, yielding a corrosion rate of 3.39 mmpy and 4.02 mmpy at 333 ?K with the incorporation of 1000 ?ppm WBW and WBE extracts, respectively. The thermodynamic study implied that the adsorption process follows the Langmuir isotherm with free energy adsorption of ΔG_ads WBW ?= ?-17.29 ?kJ ?mol^-1 and ΔG_ads WBE ?= ?-16.81 ?kJ ?mol^-1. Corresponding to the molecular modelling study, the semi-empirical method and molecular dynamics (MD) simulation investigated the correlation between the inhibitor compounds and the metal surface. One of the phenolic molecule constituents (gallic acid) was chosen to establish the structural and electronic parameters responsible for the high inhibition efficiency. A greater E_binding of 0.181 (a.u.) indicates that gallic acid in WB extracts can easily bind with the Fe surface, thus projecting a higher inhibitory performance. Surface morphology study affirmed the effective adsorption of WB extracts onto the surface of reinforced steel.     

Corrosion inhibition performance of 1,3,5-triazinyl urea derivatives as a corrosion inhibitor for mild steel in 1?N HCL

The inhibition effect of 1,3,5-triazinyl urea derivatives, viz. 1-(4-cyclohexyl amino)-6-(3,4-dimethoxy phenyl ethyl amino)-1,3,5-triazin-2-yl)-3-p-tolyurea (4-CADT) and 1-(4-chlorophenyl)-3-(4-(cyclohexyl amino)-6-(3,4-dimethoxy phenyl ethyl amino)-1,3,5-triazin-2-yl) urea (4-CCADT), were evaluated against mild steel (MS) corrosion in 1 N HCl solutions using conventional weight loss, potentiodynamic polarization, linear polarization, electrochemical impedance spectroscopy, and scanning electron microscopic studies. The losses in weights of MS samples have proved that both were efficient corrosion inhibitors. The mixed mode of inhibition was confirmed by electrochemical polarizations and the results of electrochemical impedance spectroscopy have shown the changes in the impedance parameters like charge transfer resistance and double-layer capacitance to confirm the strong adsorption on the MS surface inhibition of MS. The changes in concentrations of the inhibitors were due to the adsorption of the molecules evaluated leading to the formation of a protective layer on the surface of MS. The inhibition action of these compounds was assumed to occur via adsorption on the steel surface through the active centers contained in the molecules.     

Synthesis and evaluation of some quinoline Schiff bases as a corrosion inhibitor for mild steel in 1 N HCl

N-((2-chloroquinolin-3-yl)methylene)aniline (CQM) and N-((2-chloroquinolin-3-yl)methylene)-5-methylthiazol-2-amine (CQMA) were synthesized. The effect of CQM and CQMA have been investigated against mild steel (MS) in 1 N HCl solutions using conventional weight loss, potentiodynamic polarization, linear polarization, electrochemical impedance spectroscopy, UV–Vis spectroscopy and scanning electron microscopic studies. The losses in the weights of MS samples have proved that both CQM and CQMA are efficient inhibitors. The mixed mode of inhibition was confirmed by electrochemical polarizations. The adsorptions of these inhibitors are found to follow the Langmuir adsorption isotherm. CQM and CQMA adsorbs on the MS sample by chemisorptions.     

The effect of some triazole derivatives as inhibitors for the corrosion of mild steel in 5 % hydrochloric acid

Corrosion inhibition by triazole derivatives (n-MMT) on mild steel in 5 % hydrochloric acid (HCl) solutions has been investigated by weight loss and electrochemical methods. The results obtained revealed that these compounds performed excellently as corrosion inhibitors for mild steel in HCl solution. Potentiodynamic polarization studies showed that they suppressed both the anodic and cathodic processes and inhibited the corrosion of mild steel by blocking the active site of the metal. The effect of temperature on the corrosion behavior of mild steel in 5 % HCl with the addition of different concentrations of the inhibitors was studied in the temperature range from 303 to 333 K. The associated activation corrosion and free adsorption energies were determined. The adsorption of these compounds on the mild steel surface obeys the Langmuir adsorption isotherm. The effect of molecular structure on the inhibition efficiency has been investigated by quantum chemical calculations. The electronic properties of inhibitors were calculated and are discussed.     

Synergistic effect of AM-4VP-9 copolymer and iodide ion on corrosion inhibition of mild steel in 1 M H2SO4

The effect of iodide ions on the corrosion inhibition of mild steel in 1 M sulfuric acid in the presence of poly(acrylamide-co-4-vinylpyridine) copolymer abbreviated by (AM-4VP-9) was studied by weight loss measurements and electrochemical techniques (impedance spectroscopy and polarisation curves) at 18 °C. The results obtained showed that the inhibition efficiency increased with increasing copolymer concentration. It was also found that the inhibition efficiency increased with the addition of potassium iodide (KI) to the copolymer. A synergistic effect was observed between the AM-4VP-9 copolymer and KI. On the other hand, it was found that the inhibiting effect of the system (AM-4VP-9 + KI) increased with increasing immersion time. Polarisation curves indicate that (AM-4VP-9) copolymer act as mixed inhibitors. EIS measurements show an increase of the transfer resistance with the inhibitor concentration.     

Monte Carlo simulation and electrochemical performance corrosion inhibition whid benzimidazole derivative for XC48 steel in 0.5 M H2SO4 and 1.0 M HCl solutions

The inhibition of 1-(4-methoxybenzyl)-2-(4-methoxyphenyl)-1H-benzimidazole (MMB) on corrosion of XC48 steel in solutions 1.0 M HCl and 0.5 M H₂SO₄ were studied by potentiodynamic polarization and electrochemical impedance spectroscopy techniques (EIS). Potentiodynmic polarization curves revealed that MMB acts as a mixed-type inhibitor in both acidic media. The impedance results indicated that the corrosion process occurs under activation control. Furthermore, MMB shows a higher inhibition efficiency in HCl (97%) than in H₂SO₄ (92%) at 10^?4 M MMB. The values of ΔG°_ads, ΔH_a, E_a and ΔS_a in temperature range 293–323 K indicated that MMB strongly retarded the corrosion of XC48 steel in both solutions by a chemisorptions process. The adsorption of Benzimidazole (MMB) on carbon steel surface followed Langmuir adsorption isotherm. Scanning electron microscopy (SEM) analysis confirmed that there is an adsorbed film on the surface of XC48 steel. The results of Monte Carlo simulations studies confirmed the inhibition action of MMB.     

Schiff’s base derived from the pharmaceutical drug Dapsone (DS) as a new and effective corrosion inhibitor for mild steel in hydrochloric acid

The inhibition ability of Dapsone’s Schiff’s base with salicylaldehyde (1:2) for mild steel corrosion in 1 M HCl solution at 308 K was studied by means of potentiodynamic polarization, electrochemical impedance spectroscopy techniques, and gravimetric analysis. Results showed that Dapsone salicylaldehyde performed well as a good inhibitor for mild steel in 1 M HCl solution with maximum inhibition efficiency of 95 % at 500 ppm. The adsorption isotherm of the inhibitor followed the Langmuir adsorption. The value of free energy of adsorption showed that it is a spontaneous process and followed typical physical adsorption.     

Solid–Liquid Stable Equilibrium of the Quaternary System LiCl + NaCl + Li2SO4 + Na2SO4 + H2O at 288.15 K

Journal of Solution Chemistry - In this study, the isothermal saturation method was applied to obtain the data for solid–liquid equilibria in a system consisting of four solids...     

Measurement and correlation of the (p, ρ, T) relation of liquid cyclohexane,toluene, and ethanol in the temperature range from 233.15 K to 473.15 K at pressures up to 30 MPa for use as density reference liquids

Comprehensive (p, ρ, T) measurements on cyclohexane, toluene, and ethanol were carried out in the homogeneous liquid phase for temperatures from 233.15 K to 473.15 K at pressures up to 30 MPa. The measurements were performed by using an accurate single-sinker densimeter based on the Archimedes’ buoyancy principle. The total uncertainty of the measurements in density was estimated to be 0.015% (level of confidence 95%). Based on the experimental results, accurate correlation equations for the density of the three liquids have been established; their uncertainty is 0.020%. Comparisons with previous results of other experimentalists and with values calculated from current equations of state are presented. In this context it is also shown that the density of a liquid can vary slightly depending on the batch of the liquid used for the measurements. The purpose of this work was to provide accurate correlation equations for the densities of the three selected liquids so that these liquids can be used as density reference liquids for the calibration of densimeters and, in particular, for the calibration of vibrating-tube densimeters.     

CO2/H2S corrosion behavior of tubular steel SM 80SS in Cl−-containing solution in the absence or presence of Ca2+ and Mg2+

CO₂/H₂S corrosion behavior of tubular steel SM 80SS have been investigated utilizing electrochemical measurement technology, weight loss test, scanning electron microscope (SEM) and X-ray diffraction (XRD). The results showed that temperature increased the corrosion rate and changed the corrosion mechanism of tubular steel SM 80SS. Cl^? quickened the anodic dissolution and increased the corrosion rate of tubular steel SM 80SS. Furthermore, the addition of Ca²⁺ and Mg²⁺ resulted in the corrosion products changing from crystalline FeCO₃ to amorphous Fe(Ca,Mg)(CO₃)₂ and serious corrosion under scale of tubular steel SM 80SS.     

PEG–SO3H as a mild, efficient and green catalytic system for the synthesis of pyrazole derivatives in aqueous medium

A versatile, alternative and environmentally benign strategy for the synthesis of a series of pyrazoles has been successfully performed in water using PEG–SO₃H as an acidic catalyst. The products are obtained in high yield from the one-pot reaction procedure involving dicarbonyl compounds and hydrazines/hydrazides. This new method totally avoids the use of organic acids and toxic or expensive solvents in this reaction. The catalyst is waste-free, easily prepared, and efficiently re-used.     

Flow-calorimetric results for the massic heat capacitycpand the Joule–Thomson coefficient of CH4, of (0.85CH4 + 0.15C2H6), and of a mixture similar to natural gas

As a part of an international project, initiated by the Ruhrgas AG, the massic heat capacity c_pand the Joule–Thomson coefficient μ_JTwere measured with flow calorimeters. Great effort was made in the designing and construction of the equipment and in the experiments to reach a high accuracy of the results. The pressure range of the measurements was 0.5 MPa to 30 MPa and the temperature range 250 K to 350 K. The results are contained in the present paper. They yield the enthalpy as a function of temperature and pressure. Within the project they contribute to the experimental basis for a formulation of an equation of state.     

Crystal structure as the basis for the lack of enantiotropic mesomorphism in 3-hydroxy-4-propionylphenyl-4′-<Emphasis Type="Italic">n</Emphasis>-alkyloxybenzoates

Features of the molecular structure and crystal packing of the mesogenic compounds 3-hydroxy-4-propionylphenyl esters of 4-n-amyloxy (1), 4-n-hexyloxy (2), 4-n-heptyloxy (3), and 4-n-octyloxybenzoic acid (4) have been analyzed on the basis of X-ray diffraction (XRD) data. Comparison of the results of XRD and DSC studies of these compounds has shown that the crystalline modification studied for each of the compounds is not a precursor to the mesophase. The possibility of mesophase formation from the melt is discussed.     

Influence of –SO3H functionalization (N-SO3H or N-R-SO3H,where R = alkyl/benzyl) on the activity of Brönsted acidic ionic liquids in the hydration reaction

Sulfonic acid group functionalized imidazole based Brönsted acidic ionic liquids (BAILs) were synthesized and their activities were investigated in the hydration reaction of alkynes. The Hammett acidity order determined from UV–visible spectroscopy of BAILs is consistent with their activity order observed in hydration reactions. Theoretical studies further help to establish the structure–activity relationship. Recycling experiments suggest that these novel BAILs can be reused without significant loss in activity. Applicability of BAILs in hydration reaction opens a non-toxic, economical, and eco-friendly route to synthesize alkyl ketones from alkynes.     

KAl(SO4)2 · 12H2O as a Recyclable Lewis Acid Catalyst for Synthesis of Spirooxindoles in Aqueous Media

A simple and efficient procedure for the synthesis of spirooxindole has been described that employs a three-component condensation reaction in one pot using isatin, active methylene reagent, and 1,3-dicarbonyl compounds in an aqueous medium.     

Phosphate ion vibrations in dihydrogen phosphate salts of the type M(H2PO4)2·2H2O (M = Mg,Mn, Co,Ni, Zn,Cd): Spectra–structure correlations

The infrared, far-infrared and Raman spectra of acid phosphate salts of the type M(H₂PO₄)₂·2H₂O (M = Mg, Mn, Co, Ni, Zn, Cd) in both protiated and deuterated forms have been recorded at ambient and liquid nitrogen temperature. The vibrational spectra have been interpreted with respect to the vibrations of the H₂PO₄⁻ ions. Strong vibrational couplings are established between the PO₄ stretching modes and POH bending modes as well as between the PO₄ bending modes and the water librations. The magnitude of the correlation field splittings A–B and g–u of the vibrational modes have been estimated. The influence of the metal ions on the frequencies of the stretching vibrations of the PO bonds has been discussed and some trends regarding the frequency variation within the M(H₂PO₄)₂·2H₂O series have been found. It has been established that the extent of the energetic distortions of H₂PO₄⁻ with respect to the PO bond lengths revealed by the spectroscopic data correlates with the extent of the geometric distortion shown by the structural data.     

The measurements of coexistence curves and light scattering for {xC6H5CN + (1 − x)CH3(CH2)10CH3} in the critical region

The coexistence curves and light scattering data for a critical solution of (benzonitrile + dodecane) have been reported. The critical exponents relating to the difference in density variables of two coexisting phases β, the correlation length ν, and the osmotic compressibility γ have been determined. The experimental results of the coexistence curves have also been analyzed to examine the Wegner correction terms and the behavior of the diameter of the coexistence curves. The data analysis shows that the 3D-Ising behavior is valid in a temperature range close to the critical point. However, in a wide temperature range the exponential values of ν and γ change with the temperature significantly, clearly exhibiting the critical crossover from the 3D-Ising universality class to the classical one.