毛细管气相色谱法测定中药中有机磷农药残留量

建立了中药中多种有机磷农药残留量的毛细管气相色谱测定方法。样品以丙酮-石油醚混合溶剂为提取剂,超声提取后,用固相吸附层析柱(装填4g弗罗里硅土和2g中性氧化铝)净化,采用GC—FPD法同时测定中药中多种有机磷农药残留量。方法检出限为0．011～0．015μg／mL,回收率为85．5％～107．8％。该法简便、准确,能满足实际样品分析。     

基质固相分散法与固相萃取法在检测水产品中己烯雌酚残留中的应用

分别建立了基质固相分散（MSPD）法、固相萃取（SPE）法与气相色谱/质谱联用（GC-MS）测定水产品中己烯雌酚（DES）残留量的分析方法,并对MSPD与SPE 2种样品前处理方法的效果进行了比较。MSPD法中样品以弗罗里硅土（Florisil）作为固相分散剂,经乙酸乙酯提取,再用Florisil净化;SPE法中样品经乙酸乙酯超声提取,过Florisil小柱进行净化,最后经GC-MS在选择离子监测模式下测定水产品中DES。在优化的色谱条件下,方法的线性范围为1-300 μg/L,相关系数为0.9985。M     

固相萃取高效液相色谱法测定冬虫夏草中的甘露醇

研究了用固相萃取预分离高效液相色谱法测定冬虫夏草中甘露醇的方法。冬虫夏草样品用水超声振荡提取后用Waters Sep-Pak—C18固相萃取小柱预分离，以HC-75钙型阳离子交换柱为固定相，水为流动相，示差折光仪为检测器检测测定冬虫夏草样品中的甘露醇含量。方法检测限为2．0μg/mL，RSD在1．1％-1．6％之间，标准回收率在96％-104％之间。     

微波辅助萃取-固相微萃取联用气相色谱-质谱法测定土壤中的扑草净

研究了微波辅助萃取-固相微萃取联用、气相色谱-质谱联用测定土壤中除草剂扑草净的分析方法。采用正交设计实验优化了萃取溶剂种类和体积、微波辐射时间和微波功率等微波辅助萃取条件;研究了SPME萃取涂层、搅拌速度、萃取时间和解吸时间等对萃取效率的影响。方法的检出限为0．01ng／g;线性范围为0．2—200μg／L。在优化的条件下测定了5和50ng/g的合成土壤样品,回收率分别为90．1％和91.6％;相对标准偏差分别为9．4％和8．8％(n=6)。本法综合了微波辅助萃取和固相微萃取的优点,操作简便．灵敏度高,特别适合于固体样品中痕量有机物的萃取分离。     

DNA荧光探针—荧光素-中性红体系的研究

基于DNA对荧光素(FL)-中性红(NR)分子间荧光能量转移的抑制作用，以荧光素-中性红为荧光探针，考察该探针与DNA的结合反应，建立了准确测定DNA的新方法，在pH＝6.5条件下，hsDNA、ctDNA和smDNA的浓度与荧光素-中性红体系的荧光比值变化量Δ(Fd／Fa)成线性关系，响应线性范围分别为0．25-6．25μg／mL、0．10-5．00μg／mL、0．10-4．00μg／mL，0.025μg/mL和0．023μg／mL；分析测定了DNA合成样品，回收率91．3％-101．4％，相对标准偏差小于4．2％．     

固相萃取-毛细管气相色谱法测定中草药及其土壤中多种有机氯农药残留量

建立了中草药及其土壤中多种有机氯农药残留量的固相萃取-毛细管气相色谱(SPE-CGC)分析方法,并对7种中草药及其土壤中多种有机氯农药残留量的相关性进行了初步研究。样品以正己烷-丙酮用超声波提取,Florisil(1 g)固相萃取小柱快速净化提取物。采用SPB-5弹性石英毛细管柱分离样品,GC-ECD检测7种中草药及其土壤中的13种有机氯农药的残留量。方法的线性范围为1.26×10-10~2.24×10-7g/mL;检出限为6.4×10-11~6.1×10-10g/mL;加样平均回收率为87.3%~104.4%(RSD为1.1%~7.0%)。     

高效液相色谱法测定禽蛋及其制品中的三聚氰胺

建立了高效液相色谱测定禽蛋类及加工品中三聚氰胺的检测方法．以经三聚氰胺标准添加的鸡蛋、咸鸭蛋和松花蛋为代表性样品,优化了提取溶剂的种类、用量和提取时间条件,探讨了直接过滤、正己烷反萃和固相萃取三种前处理方式的净化效果,并考察了测定时流动相比例和缓冲液的pH条件．实验结果表明：当添加浓度为0．20和10．0μg／g时,三聚氰胺的回收率分别为87．6％-101．5％,测量标准偏差为1．6％～2．8％,方法检出限为0．05μg／g．标准溶液在0．10～2．00μg／mL范围内,线性关系良好,相关系数r=0．9999．利用本方法对12个实际禽蛋样品进行测定,结果表明能够满足禽蛋及其制品中三聚氰胺残留的快速筛查要求．     

高效液相色谱法同时测定调味料中的8种合成着色剂

建立一种同时测定调味料中8种合成着色剂的高效液相色谱分析方法。样品经30％甲醇水溶液提取,采用Diamonsil—C18柱（250mm×4．6mm）,以甲醇-1．55g／L乙酸铵为流动相,在最佳梯度洗脱条件下对8种合成着色剂进行分离,二极管阵列检测器检测,外标法定量。8种合成着色剂的线性范围为0．5～10．0μg／mL,回收率为95．0％～101％。对样品进行6次重复测定,峰面积测定结果的相对标准偏差为0．84％-3．51％（n=6）。     

高效毛细管电泳-电导检测对四环素衍生物分离测定的研究

运用毛细管电泳-电导检测方法对4种四环素衍生物——土霉素(OTC)、金霉素(CTC)、强力霉素(DOC)和四环素(TC)的分离进行了研究。在3．5mmol/L三羟基氨基甲烷(Tris)-7．5mmol/L柠檬酸(Cit)pH4．0的运行缓冲液中，4种四环素衍生物在15min内获得完全分离。四环素衍生物的线性范围分别为5．0-500μg/mL OTC，3．6-420μg/mL CTC，4.5-470μg/mL DOC和2.5-400μg/mL TC。检测限(S／N＝3)分别为OTC2．0μg/mL，CTC 1．8μg／mL，DOC2．5μg/mL和TC1．0μg/mL。采用本法对实际样品强力霉素片中强力霉素和土霉素片中土霉素进行测定，回收率分别为97．2％和96.4％。     

固相微萃取-气相色谱/三重四级质谱法测定土壤中氯代苯胺类残留

建立了固相微萃取-气相色谱/三重四级质谱法( SPME-GC/QQQ)同时测定土壤中多种氯代苯胺的方法。优化了多反应监测( MRM)的仪器条件,研究了土壤取样量、加水量、萃取温度、萃取时间对SPME富集效果的影响,确定最佳实验条件为：取8 g土壤样品加入4 mL纯净水中,80℃下萃取40 min。方法的检出限为1~10 pg/g,线性范围为5~1000 pg/g。200 pg/g加标土壤的回收率在96.8%~144.2%,相对标准偏差在13.4%~27.8%(n=5)。方法综合了SPME简便快捷和MRM高选择性的优点,尤其适合于土壤中痕量氯代苯胺类污染物的大量快速筛查分析。     

Miniaturized matrix solid‐phase dispersion combined with ultrasound‐assisted dispersive liquid–liquid microextraction for the determination of three pyrethroids in soil

A simple and miniaturized pretreatment procedure combining matrix solid‐phase dispersion (MSPD) with ultrasound‐assisted dispersive liquid–liquid microextraction (UA‐DLLME) technique was proposed in first time for simultaneous determination of three pyrethroids (fenpropathrin, cyhalothrin and fenvalerate) in soils. The solid samples were directly extracted using MSPD procedure, and the eluent of MSPD was used as the dispersive solvent of the followed DLLME procedure for further purification and enrichment of the analytes before GC‐ECD analysis. Good linear relationships were obtained for all the analytes in a range of 5.0–500.0 ng/g with LOQs (S/N=10) ranged from 1.51 to 3.77 ng/g. Average recoveries at three spiked levels were in a range of 83.6–98.5% with RSD≤7.3%. The present method combined the advantages of MSPD and DLLME, and was successfully applied for the determination of three pyrethroids in soil samples.     

Matrix solid-phase dispersion extraction of carbadox and olaquindox in feed followed by hydrophilic interaction ultra-high-pressure liquid chromatographic analysis

A new method involving matrix solid-phase dispersion (MSPD) extraction and hydrophilic interaction ultra-high-pressure liquid chromatography (HILIC-UHPLC) with photodiode array detection was developed for the determination of carbadox and olaquindox in feed. Separation of carbadox and olaquindox was achieved within 1 min on the 1.7 microm Acquity UPLC BEH HILIC column by using isocratic elution with a mobile phase consisting of 10 mmol L(-1) ammonium acetate in acetonitrile-water (95:5, v/v) at a flow rate of 0.5 mL min(-1). Optimization of MSPD extraction parameters, such as type of solid sorbent and elution solvent were carried out. Optimal conditions selected for MSPD extraction were: 0.25 g of feed sample, 0.5 g of octadecylsilica as solid sorbent and 10 mL of acetonitrile-methanol (8:2, v/v) as eluting solvent. Both analytes provided average recoveries from spiked feed samples ranging from 89.1 to 98.4% with relative standard deviations less than 10%. Obtained performance characteristics are comparable to those achieved by liquid-liquid extraction-HPLC with the advantages of being simpler and significantly faster.     

Determination of 266 pesticide residues in apple juice by matrix solid-phase dispersion and gas chromatography-mass selective detection

A macro matrix solid-phase dispersion (MSPD) method was developed to extract 266 pesticides from apple juice samples prior to gas chromatography-mass selective detection (GC-MSD) determination. A 10 g samples was mixed with 20 g diatomaceous earth. The mixture was transferred into a glass column. Pesticide residues were leached with a 160 mL hexane-dichloromethane (1:1) at 5 mL/min. Two hundred and sixty-six pesticides were divided into three groups and detected by GC-MSD under selective ion monitoring. The proposed method takes advantage of both liquid-liquid extraction and conventional MSPD methods. Application was illustrated by the analysis of 236 apple juice samples produced in Shaanxi province China mainland this year.     

Determination of phenolic compounds in wines by novel matrix solid-phase dispersion extraction and gas chromatography/mass spectrometry

A novel matrix solid-phase dispersion (MSPD) extraction method was developed to extract simultaneously 23 phenolic compounds from wine samples prior to determination by gas chromatography with mass spectrometric detection in the selected ion monitoring mode. Different parameters of the MSPD technique such as dispersant solid-phase, eluting solvent, and sample ionic strength and pH were optimized. The optimized MSPD procedure requires a small volume of wine (1 mL), commercial silica gel (1.5 g) as dispersant solid-phase and a small volume of ethyl acetate (5 mL) as eluting solvent. Under these conditions, the extraction of the studied compounds was almost complete (mean values of recoveries between 87 and 109%) in a short time (15 min). Moreover, satisfactory standard deviations of repeatability (RSD<9% in most cases), linear regression coefficients (r(2)>0.993) and detection limits (<8 microg/L) confirm the usefulness of the methodology for routine monitoring of the concentration of individual phenolic antioxidants in wines. Application was illustrated by analysis of different wine samples.     

在对映体水平上测定土壤中烯效唑的方法

目前使用的农药中约25％是手性化合物.手性农药对映体的生物活性往往有很大差异,例如常用的三唑类植物生长调节剂烯效唑(Uniconazole),其S体的活性是R体的7倍.但目前绝大多数手性农药是以消旋体形式使用的.对于手性农药,目前的研究工作主要集中在其作为农药的生物活性的对映体选择性上,而对其环境行为的对映体选择性研究则很少,缺乏在对映体水平上测定环境介质.     

Evaluation of two fast and easy methods for pesticide residue analysis in fatty food matrixes

Two rapid methods of sample preparation and analysis of fatty foods (e.g., milk, eggs, and avocado) were evaluated and compared for 32 pesticide residues representing a wide range of physicochemical properties. One method, dubbed the quick, easy, cheap, effective, rugged, and safe (QuEChERS) method for pesticide residue analysis, entailed extraction of 15 g sample with 15 mL acetonitrile (MeCN) containing 1% acetic acid followed by addition of 6 g anhydrous magnesium sulfate and 1.5 g sodium acetate. After centrifugation, 1 mL of the buffered MeCN extract underwent a cleanup step (in a technique known as dispersive solid-phase extraction) using 50 mg each of C18 and primary secondary amine sorbents plus 150 mg MgSO4. The second method incorporated a form of matrix solid-phase dispersion (MSPD), in which 0.5 g sample plus 2 g C18 and 2 g anhydrous sodium sulfate was mixed in a mortar and pestle and added above a 2 g Florisil column on a vacuum manifold. Then, 5 x 2 mL MeCN was used to elute the pesticide analytes from the sample into a collection tube, and the extract was concentrated to 0.5 mL by evaporation. Extracts in both methods were analyzed concurrently by gas chromatography/mass spectrometry and liquid chromatography/tandem mass spectrometry. The recoveries of semi-polar and polar pesticides were typically 100% in both methods (except that basic pesticides, such as thiabendazole and imazalil, were not recovered in the MSPD method), but recovery of nonpolar pesticides decreased as fat content of the sample increased. This trend was more pronounced in the QuEChERS method, in which case the most lipophilic analyte tested, hexachlorobenzene, gave 27 +/- 1% recovery (n=6) in avocado (15% fat) with a<10 ng/g limit of quantitation.     

Metal–organic framework assisted matrix solid-phase dispersion microextraction of saponins using response surface methodology

An efficient and simple metal–organic framework (MOF) assisted matrix solid-phase dispersion (MSPD) microextraction was developed for the extraction of the five saponins in P. ginseng leaves. The target analyses were detected by ultra high performance chromatography coupled with time-of-flight MS. Experimental conditions for MSPD microextraction were optimized by the Box–Behnken design of the response surface methodology. The optimal conditions were as follows: 20 mg adsorbent, 80% methanol–water solution for elution, 60 s grinding time, and the MOF-808 as the adsorbent. With the final optimized method, the calibration curves for five saponins showed good linearity (R² > 0.998) within range of 0.01–100 μg/mL. In addition, analytical recoveries ranged from 87.04 to 103.78%, with the RSD below 5%. The limit of detection and LOQ range from 0.087 to 0.114 μg/mL and 0.292 to 0.379 μg/mL, respectively. Compared with the traditional extraction method and published methods, the newly MOF-assisted MSPD extract exhibited higher extraction efficiency, simpler operation, and provided a cleaner extract with low consumption of organic reagents that was applied for rapid evaluation and quality control of active compounds from plants.     

Fast and precise determination of phenthoate and its enantiomeric ratio in soil by the matrix solid-phase dispersion method and liquid chromatography

A fast and precise method was developed for the determination of phenthoate and its enantiomeric ratio (ER) in three soil samples. A recently developed sample pretreatment technology--matrix solid-phase dispersion (MSPD) was used to extract phenthoate simply and effectively. MSPD conditions, i.e. solid-phase Florisil amount, water content of Florisil-soil mixture, the constituent and volume of the eluting solvent, were optimized stepwise. The MSPD extract was directly used for quantitative determination of phenthoate by silica-based high-performance liquid chromatography (HPLC) with UV detection. The recoveries of phenthoate from three different types of soils fortified at three levels of 0.1, 1, 10 microg/g ranged from 75 to 94% with RSDs of 1.5-6.5%. On this basis, phenthoate was further isolated from the remainder of MSPD extract by silica-based HPLC and then ER determined on HPLC with cellulose tris-3, 5-dimethylphenylcarbamate as chiral stationary phase. The ERs determined in the soils spiked with racemic or enantiomer-enriched phenthoate agreed sufficiently well with those in the corresponding standard solutions. Finally, the proposed method was successfully applied to the study of enantioselective degradation of phenthoate in the three soils under laboratory conditions. High enantioselectivity was observed in the two alkaline soils with (+)-enantiomer degrading faster than the (-)-enantiomer, while there was little to no enantioselectivity in the acidic soil. The methodology can be used to study the enantioselective environmental behavior of chiral pollutants.     

New micromethod combining miniaturized matrix solid-phase dispersion and in-tube in-valve solid-phase microextraction for estimating polycyclic aromatic hydrocarbons in bivalves

Miniaturized matrix solid-phase dispersion (MSPD) was developed for the extraction of common polycyclic aromatic hydrocarbons (PAHs) from bivalve samples (100mg, dry weight). Additional clean-up and analyte enrichment was accomplished by in-tube solid-phase microextraction (SPME). For this purpose the extracts collected after MSPD were diluted with water and injected into a capillary column coated with the extractive phase. This capillary column was connected to the analytical column by means of a switching valve. Separation and quantification of the PAHs were carried out using a monolithic LC column and fluorescence detection. Since the in-tube SPME device allowed the processing of large volumes of the extracts (2.0 mL) excellent sensitivity was achieved, thus making solvent evaporation operations unnecessary. The overall recoveries ranged from 10% to 28% for the studied compounds. The relative standard deviation (RSD) ranged from 2% to 10% for intra-day variation (n=3), and the limits of detection (LODs) were < or =0.6 ng/g (dry weight). The proposed procedure was very simple and rapid (total analysis time was approximately 20 min), and the consumption of organic solvents and extractive phases was drastically reduced. The reliability of the proposed MSPD/in-tube SPME method was tested by analysing several bivalves (mussels and tellins) as well as a standard reference material (SRM).     

A rapid method based on hot water extraction and liquid chromatography-tandem mass spectrometry for analyzing tetracycline antibiotic residues in cheese

A rapid, specific, and sensitive procedure for determining residues of 4 widely used tetracycline antibiotics and 3 of their 4-epimers in cheese is presented. The method is based on the matrix solid-phase dispersion (MSPD) technique followed by liquid chromatography/tandem mass spectrometry (LC/MS/MS). After dispersing samples of mozzarella, asiago, parmigiano, gruyere, emmenthal, and camembert on sand, target compounds were eluted from the MSPD column by passing through it 6 mL water heated at 70 degrees C. After acidification and filtration, 200 microL of the aqueous extract was directly injected into the LC column. For analyte identification and quantification, MS data acquisition was performed in the multireaction monitoring mode, selecting 2 precursor ion-to-product ion transitions for each target compound. Hot water appeared to be an efficient extractant, because absolute recoveries were no lower than 78%. Using demeclocycline as a surrogate analyte, recoveries of analyte added to the 6 types of cheeses at the 30 ng/g level were 96-117%, with relative standard deviation (RSD) not higher than 9%. Statistical analysis of the mean recovery data showed that the extraction efficiency was not dependent on the type of cheese analyzed. This result indicates that this method could be applied to other cheese types not considered here. At the lowest concentration considered, i.e., 10 ng/g, the accuracy of the method ranged between 90 and 107%, with RSDs not larger than 12%. Based on a signal-to-noise ratio of 10, limits of quantitation were estimated to be 1-2 ng/g.