Stability-indicating methods for the determination of linezolid in the presence of its alkaline-induced degradation products

Three methods are presented for the determination of linezolid in the presence of its alkaline-induced degradation products. The first method was based on separation of linezolid from its alkaline degradation product by TLC followed by densitometric measurement of the spots of intact drug at 244 nm. The separation was carried out on silica gel 60 F₂₅₄ using isobutanol:ammonia (9:1 v/v) as a mobile phase. The second method was based on first derivative ¹D ultraviolet spectrophotometry with zero crossing point and peak to base measurement. The ¹D value at 251.4 nm was selected for the assay of linezolid in the presence of degradation product. The third method was depended on the first derivative of the ratio spectra ¹DD by measurement of the value at 263.6 nm. The proposed methods were successfully applied to the determination of the drug in bulk powder, in laboratory prepared mixtures with its degradation product and in commercial tablets.     

Stability-indicating derivative spectrophotometry method for the determination of biapenem in the presence of its degradation products

A first-derivative UV spectrophotometric method, with or without the subtraction technique, was developed for the determination of biapenem in pharmaceutical dosage form in the presence of its degradation products. The method was based on the measurement of first-derivative amplitudes at zero crossing point (λ = 312 nm) and the peak-to-zero technique and validated with regard to linearity, limits of detection and quantitation, selectivity and precision. The observed rate constants for the degradation of biapenem were comparable to those obtained in the stability-indicating HPLC method.      

Stability-indicating RP-HPLC method for simultaneous quantitation of tramadol and aceclofenac in presence of their major degradation products: Method development and validation

Primary objective of this study was to develop a stability-indicating reverse-phase high-performance liquid chromatography (HPLC) method for simultaneous quantitation of tramadol and aceclofenac in presence of their degradation products. The drugs were subjected to various International Conference on Harmonization recommended stress conditions, such as acid hydrolysis, alkaline hydrolysis, peroxide oxidation, thermolysis, and photolysis. The major degradation products got well resoluted from the analytes in HPLC analysis with a mobile phase composed of a mixture of 0.01?M ammonium acetate buffer (pH 6.5) and acetonitrile (65:35, v/v) through a Phenomenex Gemini C18 (250?mm?×?4.6?mm, 5?µm particle size) column. The method was linear over a range of 15–60?µg/mL for tramadol and 40–160?µg/mL for aceclofenac concentration. The analytes were detected at a wavelength of 270?nm. The method was validated and found to be specific, accurate, precise, stable, and robust for its intended use. The method can be recommended for its future use in routine quality control, accelerated and real-time stability analysis of the formulations containing tramadol and aceclofenac combination.     

Stability-indicating methods for determination of pyritinol dihydrochloride in the presence of its precursor and degradation product by derivative spectrophotometry

A first-derivative spectrophotometric (1D) method and a derivative-ratio zero-crossing spectrophotometric (1DD) method were used to determine pyritinol dihydrochloride (I) in the presence of its precursor (II) and its degradation product (III) with 0.1N hydrochloric acid as a solvent. Linear relationships were obtained in the ranges of 6-22 microg/mL for the (1D) method and 6-20 microg/mL for the (1DD) method. By applying the proposed methods, it was possible to determine pyritinol dihydrochloride in its pure powdered form with an accuracy of 100.36 +/- 1.497% (n = 9) for the (1D) method and an accuracy of 99.92 +/- 1.172% (n = 8) for the (1DD) method. Laboratory-prepared mixtures containing different ratios of (I), (II), and (III) were analyzed, and the proposed methods were valid for concentrations of < or = 10% (II) and < or = 50% (III). The proposed methods were validated and found to be suitable as stability-indicating assay methods for pyritinol in pharmaceutical formulations.     

Stability-indicating method for the determination of clorazepate dipotassium-I. Via its final degradation products

A sensitive spectrophotometric procedure is described for the determination of 1,4-benzodiazepine (clorazepate dipotassium) in the presence of its degradation products. The procedure is based on acid hydrolysis of clorazepate dipotassium to yield its final degradation products viz., 2-amino-5-chlorobenzophenone and glycine. The amino-chlorobenzophrenone is extracted from the neutralized hydrolysate with diethyl ether, the extract is evaporated, the residue is dissolved in methanol and its absorbance measured at about 240 nm or 380 nm. Glycine, left in the aqueous layer after etherial extraction of aminochlorobenzophenone, is treated with ninhydrin reagent in the presence of pyridine and the bluish violet colour formed is measured at about 560 nm. The suggested procedures determine 20–100 mg of clorazepate dipotassium via its degradation products aminochlorobenzophenone and glycine with mean accuracies of 100.0 ± 0.5% at 560 nm, 100.2 ± 0.6% at 380 nm and 99.8 ± 0.5%. The suggested procedures are suitable for stability-testing of clorazepate dipotassium in bulk powder and in pharmaceutical preparations.     

Stability-indicating determination of meropenem in presence of its degradation product

Stability-indicative determination of meropenem (MERM) in the presence of its open-ring degradation product, the metabolite, is investigated. The degradation product has been isolated, via acid-degradation, characterized and confirmed. Selective quantification of MERM, singly in bulk form, pharmaceutical formulations and/or in the presence of its major degradate is demonstrated. The indication of stability has been undertaken under conditions likely to be expected at normal storage. Among the analytical techniques adopted for quantification are spectrophotometry [first-derivative (¹D), first-derivative of ratio spectra (¹DD) and bivariate analysis], as well as chromatography [coupled TLC-densitometry and HPLC].     

Reversed-phase high performance liquid chromatographic method for the determination of lansoprazole, omeprazole and pantoprazole sodium sesquihydrate in presence of their Acid-induced degradation products

A simple sensitive, selective and accurate reversed-phase high performance liquid chromatographic method was developed and validated for the quantitative determination of lansoprazole, omeprazole and pantoprazole sodium sesquishydrate in the presence of their acid-induced degradation products. The three compounds were monitored at 280 nm using Nova-Pak C(18) column and a mobile phase consisting of 0.05 M potassium dihydrogen phosphate : methanol : acetonitrile (5 : 3 : 2 v/v/v). Linearity ranges were 2-20 mug ml(-1), 2-36 mug ml(-1) and 0.5-20 mug ml(-1) for lansoprazole, omeprazole and pantoprazole, respectively. The corresponding recoveries were 100.61+/-0.84%, 100.50+/-0.80% and 99.78+/-0.88%. The minimum detection limits were 0.55, 0.54 and 0.03 mug ml(-1) for lansoprazole, omeprazole and pantoprazole, respectively. The method could be successfully applied to the determination of pure, laboratory prepared mixtures and pharmaceutical dosage forms. The results obtained were compared with the reported methods for lansoprazole and pantoprazole or the official U.S.P method for omeprazole.     

Stability-indicating method for the determination of clorazepate dipotassium-II. Via N-desmethyldiazepam and determination of its degradation products

A spectrophotometric method for the determination of the intact clorazepate dipotassium in the presence of its degradation products is developed. It depends upon preliminary hydrolysis of clorazepate dipotassium-thus liberating its equivalent of N-desmethyldiazepam which is extracted, with benzene-methylene chloride (9:1). The extract is evaporated, the residue dissolved in methanol and its absorbance measured at about 315 nm. The procedure determines 0.4-1.6 mg of clorazepate dipotassium with an accuracy of 100.2+/-0.7%. The procedure is applied successfully for the determination of clorazepate dipotassium in bulk powder and in capsules; retaining its accuracy in the presence of up to 80% degradation. Determination of the different degradation products is also possible. Thus, N-desmethyl diazepam is determined after preliminary extraction with benzene-methylene chloride mixture, followed by TLC separation, 2-amino-5-chlorobenzophenone by directly applying the first derivative spectrophotometric technique, and glycine in the aqueous layer determined colorimetrically with ninhydrin reagent in the presence of pyridine.     

Stability-indicating method for determination of oxyphenonium bromide and its degradation product by high-performance liquid chromatography

A high-performance liquid chromatographic (HPLC) method was developed for determination of oxyphenonium bromide (OX) and its degradation product. The method was based on the HPLC separation of OX from its degradation product, using a cyanopropyl column at ambient temperature with mobile phase of acetonitrile-25 mM potassium dihydrogen phosphate, pH 3.4 (50 + 50, v/v). UV detection at 222 nm was used for quantitation based on peak area. The method was applied to the determination of OX and its degradation product in tablets. The proposed method was also used to investigate the kinetics of the acidic and alkaline degradation of OX at different temperatures, and the apparent pseudo first-order rate constant, half-life, and activation energy were calculated. The pH-rate profile of the degradation of OX in Britton-Robinson buffer solutions within the pH range 2-12 was studied.     

Kinetics of omeprazole degradation in the presence of 2-mercaptoethanol

The reactions of omeprazole, a potent proton pump inhibitor, were investigated in the presence of 2-mercapotoethanol. Reactions were monitored in solutions buffered to pH values ranging from 2.0 to 5.0 using differential pulse polarography at the static mercury drop electrode. First-order reaction network was proposed for all conversions. It is demonstrated that acid degradation predominates at pH values ∼2–3, whereas the reaction of sulfenic acid with the more nucleophilic thiol becomes prominent at pH values around 4–5. The acidic medium is necessary for the formation of sulfenic acid, the key intermediate believed to be the active inhibitor, but acid also converts this sulfenic acid into other degradation products that are unreactive toward thiol. The present work suggests that acid inhibition may occur at pH values higher than those previously thought. Thus, “highly acidic medium is required to achieve both accumulation and activation of omeprazole in the parietal cell, but less acidic medium is necessary for the reaction of sulfenic acid intermediate with the sulfhydryl groups of cysteine residues of H⁺/K⁺-ATPase proton pump in vivo.” © 2008 Wiley Periodicals, Inc. Int J Chem Kinet 40: 352–358, 2008     

Synchronized stability indicating RP-LC methods for determination of metolazone with losartan potassium or spironolactone in presence of their degradation products

Abstract

Two precise and selective stability-indicating RP-LC methods have been developed and validated for simultaneous determination of metolazone in its binary mixture with losartan potassium (method 1) and spironolactone (method 2) in the presence of their degradation products. For method 1, the chromatographic separation was achieved on Kromasil C₁₈ column, the mobile phase consisted of a mixture of 0.1% ortho-phosphoric acid in acetonitrile and 0.1% ortho-phosphoric acid in water (28:72, v/v) pumped at flow rate 2?mL/min and UV detection at 235?nm. Linearity was determined over the concentration range of 2–16µg/mL for metolazone and 40–320µg/mL for losartan potassium. For method 2, chromatographic separation of metolazone and spironolactone was achieved on a Symmetry C₈ column using a mobile phase that consisted of acetonitrile, methanol, and 0.1% ortho-phosphoric in water in gradient mode pumped at a flow rate 1.5?mL/min with programed wavelength detection. Linearity was determined over the concentration range of 2–16µg/mL for metolazone and 20–160µg/mL for spironolactone. The suggested methods were proved to be highly selective, precise and accurate for simultaneous determination of the cited drugs in their combined pharmaceutical dosage form in the presence of their degradation products. The proposed methods were validated in compliance with ICH guidelines.

1. Highlights

2. Synchronized determination of metolazone and co-formulated drugs in presence of their degradation products.

3. Act as a method for screening of metolazone and co-formulated drugs in quality control laboratories.

4. Validation of suggested methods according to ICH guidelines.

5. The pathway of degradation of metolazone under different stress conditions was proposed.

     

Stability-indicating methods for the determination of disopyramide phosphate

Four methods were developed for the determination of intact disopyramide phosphate in the presence of its degradation product. In the first and second methods, third-derivative spectrophotometry and first derivative of the ratio spectra were used. For the third-derivative spectrophotometric method, the peak amplitude was measured at 272 nm, while for the derivative ratio spectrophotometric method, disopyramide phosphate was determined by measuring the peak amplitude at 248 and 273 nm. Both methods were used for the determination of disopyramide phosphate in the concentration range 12.5-87.5 microg/mL, with corresponding mean recovery 100.8 +/- 0.7% for the first method and 99.9 +/- 0.7% and 99.6 +/- 0.7% for the second method at 248 and 273 nm, respectively. In the third method, an ion selective electrode (ISE) was fabricated using phosphotungstic acid as an anionic exchanger, PVC as the polymer matrix, and dibutylsebacate as a plasticizer. The ISE was used for the determination of disopyramide phosphate in pure powder form in the concentration range 10(-2)-10(-5) M. The slope was found to be 58.5 (mV/decade), and the average recovery was 99.9 +/- 1.6%. The fourth method depended on the quantitative densitometric determination of the drug in concentration range of 0.25-2.5 microg/spot using silica gel 60 F245 plates and ethyl acetate-chloroform-ammonium hydroxide (85 + 10 + 5, v/v/v) as the mobile phase, with corresponding mean accuracy of 100.3 +/- 1.1%. The 4 proposed methods were found to be specific for disopyramide phosphate in presence of up to 80% of its degradation product for the spectrophotometric methods, 90% of its degradation for the densitometric method, and 40% for the ISE method. The 4 proposed procedures were successfully applied for the determination of disopyramide phosphate in Norpace capsules. Statistical comparison between the results obtained by these methods and the official method of the drug was done, and no significant differences were found.     

Stability-indicating HPLC method for the determination of nicardipine in capsules and spiked human plasma. Identification of degradation products using HPLC/MS

In this stability-indicating, reversed-phase high-performance liquid chromatographic method for nicardipine (NIC), forced degradation has been employed and the formed degradants were separated on a C18 (150 mm × 3.9 mm, 5 μm) analytical column using a mobile phase consisted of 70% methanol: acetic acid containing 0.01 M triethylamine with pH 4. The flow rate was 1.0 mL/min and the photodiode array detection wavelength was 353 nm. Forced degradation of the drug was carried out under acidic, basic, photolytic, and oxidative stress conditions. Chromatographic peak purity data indicated no co-eluting peaks with the main peaks. This method resulted in the detection of seven degradation products. Among these, two major degradation products from basic hydrolysis, one from oxidation by H₂O₂ and four from photolytic stress were identified by mass spectral data. A good linear response was achieved over the range of 0.5–40 μg/mL with a limit of detection (LOD) of 0.011 μg/mL and limit of quantification (LOQ) of 0.036 μg/mL. The suggested method was successfully applied for the analysis of NIC in its commercial capsules, with mean% recovery value of 100.11 ± 2.26%. The method was extended to the in vitro determination on NIC in spiked human plasma samples with mean% recovery of 99.04 ± 5.67%. The suggested method was utilized to investigate the kinetics of photolytic induced degradation.     

Column and thin-layer chromatographic methods for the simultaneous determination of acediasulfone in the presence of cinchocaine, and cefuroxime in the presence of its hydrolytic degradation products

Column liquid chromatography (LC) and thin-layer chromatography (TLC)-densitometry methods are described for simultaneous determination of acediasulfone (Ace) and cinchocaine (Cinco). In the LC method, the separation and quantitation of the 2 drugs was achieved on a Zorbax C8 column (5 microm, 150 x 4.6 mm id) using a mobile phase composed of methanol-phosphate buffer, pH 2.5 (66 + 34, v/v), at a flow rate of 1 mL/min and ultraviolet detection at 300 and 327 nm for Ace and Cinco, respectively. The method showed linearity over concentration ranges of 20-200 and 45-685 microg/mL, respectively. In the TLC-densitometry method, a mobile phase composed of methanol-tetrahydrofuran-acetic acid (45 + 5 + 0.5, v/v/v) was used for the separation of the 2 drugs. The linearity range was 0.5-4 and 2-9 microg/spot, respectively. In addition, stability indicating TLC-densitometry method has been developed for determination of cefuroxime sodium in the presence of 5-70% of its known hydrolytic degradation products. The mobile phase butanol-methanol-tetrahydrofuran-concentrated ammonium hydroxide (50 + 50 + 50' + 5, v/v/v/v) was used. The concentration range was 2-10 microg/spot. The optimized methods proved to be specific and accurate for the analysis of the cited drugs in laboratory-prepared mixtures and dosage forms. The obtained results agreed statistically with those obtained by the reference methods.     

Stability-indicating chromatographic methods for the determination of some oxicams

Two sensitive and selective methods were developed for the determination of some oxicams, namely, lornoxicam (LOX), tenoxicam (TEX), and meloxicam (MEX), in the presence of their alkaline degradation products. The first method is based on the thin-layer chromatographic separation of the 3 drugs from their alkaline degradation products, followed by densitometric measurement of the intact drug spots for LOX, TEX, and MEX at 380, 370, and 364 nm, respectively. The developing systems used for separation are ethyl acetate-methanol-26% ammonia (17 + 3 + 0.35, v/v/v) for LOX and TEX and chloroform-n-hexane-96.0% acetic acid (18 + 1 + 1, v/v/v) for MEX. The linear ranges were 0.25-6.0 microg/spot for LOX and TEX and 0.5-10 microg/spot for MEX, with mean recoveries of 99.80 +/- 1.32, 100.57 +/- 1.34, and 100.71 +/- 1.57%, respectively. The second method is based on the liquid chromatographic separation of the 3 drugs from their alkaline degradation products on a reversed-phase C18 column, using mobile phases of methanol-acetonitrile-acetate buffer, pH 4.6 (4.5 + 0.5 + 5.0, v/v/v) for LOX and MEX and methanol-acetonitrile-acetate buffer, pH 4.6 (1.9 + 0.1 + 3.0, v/v/v) for TEX at ambient temperature. Quantification is achieved by UV detection at 280 nm, based on peak area. The linear ranges were 0.5-20 microg/mL for LOX and TEX and 1.25-50 microg/mL for MEX, with mean recoveries of 99.81 +/- 1.01, 98.90 +/- 1.61, and 100.86 +/- 1.55%, respectively. The methods were validated according to guidelines of the International Conference on Harmonization. The developed methods were successfully applied to the determination of LOX, TEX, and MEX in bulk powder, laboratory-prepared mixtures containing different percentages of degradation products, and pharmaceutical dosage forms.     

Stability-indicating reversed-phase liquid chromatographic method for simultaneous determination of atorvastatin and ezetimibe from their combination drug products

A simple, precise, and rapid stability-indicating reversed-phase column liquid chromatographic (RP-LC) method has been developed and subsequently validated for simultaneous estimation of atorvastatin (ATV) and ezetimibe (EZE) from their combination drug product. The proposed RP-LC method utilizes a LiChrospher 100 C18, 5 microm, 250 x 4.0 mm id column at ambient temperature; the optimum mobile phase consists of acetonitrile-water-methanol (45 + 40 + 15, v/v/v) with apparent pH adjusted to 4.0 +/- 0.1; mobile phase flow rate of 1.0 mL/min; and UV detection at 250 nm. ATV, EZE, and their combination drug product were exposed to thermal, photolytic, hydrolytic, and oxidative stress conditions, and the stressed samples were analyzed by the proposed method. There were no other coeluting, interfering peaks from excipients, impurities, or degradation products due to variable stress conditions, and the method is specific for the estimation of ATV and EZE in the presence of degradation products. The response was linear over the concentration range of 1-80 microg/mL for ATV and EZE. The mean recoveries were 99.27 and 98.5% for ATV and EZE, respectively. The intermediate precision data were obtained under different experimental conditions, and the calculated value of the coefficient of variation was found to be less than the critical value. The proposed method can be useful in the quality control of bulk manufacturing and pharmaceutical dosage forms.     

Determination of pesticides and their degradation products in soil: critical review and comparison of methods

Pesticides are applied widely to protect plants from disease, weeds and insect damage, and usually come into contact with soil, where they undergo a variety of transformations that provide a complex pattern of metabolites. This article reviews the most relevant analytical methods for determining pesticides and their transformation products in soils. We address some recent advances in sampling and sample-preparation technologies for soil analysis. We discuss and critically evaluate procedures, such as liquid extraction methods (pressurized liquid extraction or microwave-assisted extraction) and solid-phase based methods (headspace solid-phase microextraction, solid-phase microextraction or matrix-solid-phase dispersion). Analysis of pesticides is generally carried out by gas chromatography (GC) or liquid chromatography (LC) coupled to different detectors, especially to mass spectrometers (MSs). However, alternative and/or complementary methods, using capillary electrophoresis (CE), biosensors and bioassays have emerged recently. We also consider the advantages and the disadvantages of the various methodologies.     

Stability-indicating reversed-phase liquid chromatographic method for simultaneous determination of simvastatin and ezetimibe from their combination drug products

A simple, precise, and rapid stability-indicating reversed-phase column liquid chromatographic (RP-LC) method has been developed and subsequently validated for simultaneous estimation of simvastatin (SIM) and ezetimibe (EZE) from their combination drug product. The proposed RP-LC method utilizes a LiChrospher 100 C18, 5 microm, 250 x 4.0 mm id column at ambient temperature; optimum mobile phase consisting of acetonitrile-water-methanol (60 + 25 + 15, v/v/v) with apparent pH adjusted to 4.0 +/- 0.1; mobile phase flow rate of 1.5 mL/min; and ultraviolet detection at 238 nm. SIM, EZE, and their combination drug product were exposed to thermal, photolytic, hydrolytic, and oxidative stress conditions, and the stressed samples were analyzed by the proposed method. There were no other coeluting, interfering peaks from excipients, impurities, or degradation products due to variable stress conditions, and the method is specific for the estimation of SIM and EZE in the presence of degradation products. The described method was linear over the range of 1-80 and 3-80 microg/mL for SIM and EZE, respectively. The mean recoveries were 99.17 and 100.43% for SIM and EZE, respectively. The intermediate precision data were obtained under different experimental conditions, and the calculated value of the coefficient of variation was found to be less than the critical value. The proposed method can be useful in the quality control of bulk manufacturing and pharmaceutical dosage forms.