Utilization of the magnetogranulometric analysis to estimate the thermal conductivity of magnetic fluids

In this study, the semi-empirical equation for the effective thermal conductivity of the Holotescu-Stoian model was applied to a set of four dilutions of a transformer oil based magnetic fluid with magnetite nanoparticles as magnetic phase, using the results obtained for the size distributions from the magnetogranulometry analysis, followed by a comparison with the measured values of the effective thermal conductivity obtained by the hot ball method. The link between the size distribution by number and by volume used in the magnetogranulometry analysis and the Holotescu-Stoian model adaptation to the lognormal distribution were presented. The comparison between the results given by the model and the corresponding experimental data showed that by using the approximated size distribution to calculate the effective thermal conductivity the analytical results much closer to the experimental ones are obtained, compared to those given by the Maxwell classical model.     

Numerical and Analytical Approaches to Modeling Critical Two-Phase Flow with Granular Layer

Based on data obtained in the previous experimental study conducted by the authors, two approaches are proposed for analytical and numerical modeling of a critical two-phase flow in a pipe with a granular layer. An analytical approach is based on a polytrophic model, while a numerical approach was developed using a smoothed particle hydrodynamics method. A model of isenthalpic flow of vapor–water mixture in a fixed bed of solid particles is considered is this study. The mixture expansion process is considered to be polytropic. Similarly to the known problem of gas dynamics of a granular bed, an analytical relationship for calculation of a critical mass velocity was obtained. The results of the calculation based on the analytical and numerical models were compared with the experimental data and agreement between analytical and numerical data and the experiment was observed.     

Wind noise measured at the ground surface

Measurements of the wind noise measured at the ground surface outdoors are analyzed using the mirror flow model of anisotropic turbulence by Kraichnan [J. Acoust. Soc. Am. 28(3), 378-390 (1956)]. Predictions of the resulting behavior of the turbulence spectrum with height are developed, as well as predictions of the turbulence-shear interaction pressure at the surface for different wind velocity profiles and microphone mounting geometries are developed. The theoretical results of the behavior of the velocity spectra with height are compared to measurements to demonstrate the applicability of the mirror flow model to outdoor turbulence. The use of a logarithmic wind velocity profile for analysis is tested using meteorological models for wind velocity profiles under different stability conditions. Next, calculations of the turbulence-shear interaction pressure are compared to flush microphone measurements at the surface and microphone measurements with a foam covering flush with the surface. The measurements underneath the thin layers of foam agree closely with the predictions, indicating that the turbulence-shear interaction pressure is the dominant source of wind noise at the surface. The flush microphones measurements are intermittently larger than the predictions which may indicate other contributions not accounted for by the turbulence-shear interaction pressure.     

Shear horizontal surface waves on piezoelectric ceramic with layered structure

This paper presents theoretical and experimental results describing the propagation of SH (shear, horizontal) surface waves on a piezoelectric ceramic with a surface layer of different polarization than that in the substrate. An analytical formula for the group velocity of the SH surface waves is developed. The velocity of impulses of the SH surface waves is determined experimentally. Further, the theoretical results are compared to the experimental values.     

对流放电CO2激光器的饱和特性

本文从微观的分子模型出发,得到了饱和强度的定量解析表达式。考虑了激励区气压、温度、流速的变化,计算了不同参量下激励区各点的饱和强度和小信号增益。分析讨论了气压、流速、气比、放电比功率对饱和强度及小信号增益的影响。并将饱和强度的计算结果与实验进行了比较,结果符合较好。 关键词：     

Experimental investigation of cooling of a plate by ionic wind from a corona-forming wire electrode

We report on the results of experimental investigations of the kinematic structure of ionic wind from a wire electrode placed near a heated plate, which plays the role of the earthed electrode. Experiments are carried out in a wide range of voltages for different polarities of the wire for several values of the electrode gap. We compare the structures of the flows emerging as a result of natural convection in open air for different positions of the plate and in the presence of a fast ionic wind jet that considerably intensifies heat transfer in the boundary layer at the heated planar electrode. Local temperature distributions over the plate surface are obtained, as well as the integral dependences of the effective heat removal on the electric parameters of the corona discharge. The velocity of air flows with ionic wind reaches 4 m/s, and the heat power removed from the plate for fixed overheating increases ninefold compared to the situation with natural convection.     

梯度倾斜相关测量水平C_n~2和横向风速廓线的理论与仿真研究

根据Rytov近似以及泰勒湍流冻结假设,推导出以不同距离的前向散射光为信标的水平路径上梯度倾斜角的相关表达式.基于该表达式,在理论上提出了计算湍流强度与横向风速的新方法,并通过数值仿真对该方法进行了初步验证.结果表明,在5%高斯误差情况下,大气折射结构常数和风速的计算结果与理论真值在整体变化上具有较好的一致性,线性相关系数分别能达到0.8与0.9.该方法能够得到不同湍流与风速条件下的湍流强度廓线以及风速廓线,为反演大气湍流强度以及风速提供了一种新思路.     

A rotating arc gas pump for circuit breaking and other applications

A rotating arc circuit breaker is described which uses an auxiliary current source to generate the magnetic field for driving the arc. Test results obtained using optical fiber measurement systems have shown that there are three main arcing phases. Initially the arc rotates at an essentially constant but low velocity, subsequently its velocity oscillates between this and much higher values, and finally the are plasma may become diffuse in nature. Test results obtained with dielectric strength probes have indicated that a unidirectional flow of arc heated gas is generated. The flow is away from the moving contact of the interrupter so promoting good dielectric strength in this critical contact region. The combination of the optical fiber and dielectric probe results indicates two possible modes of gas pumping represented, respectively, by a fan and a piston-type action of the arc. Simplified analytical models for both modes are developed with predictions obtained showing good agreement with the experimental results. Discussion of experimental results suggests that the transition from oscillatory velocity changes to diffuse arcing represents an important parameter for scaling the geometries of future interrupters and arc heaters     

Sound waves in a liquid with polydisperse vapor–gas bubbles

A mathematical model is presented for the propagation of plane, spherical, and cylindrical sound waves in a liquid containing polydisperse vapor–gas bubbles with allowance for phase transitions. A system of integro-differential equations is constructed to describe perturbed motion of a two-phase mixture, and a dispersion relation is derived. An expression for equilibrium sound velocity is obtained for a gas–liquid or vapor–liquid mixture. The theoretical results agree well with the known experimental data. The dispersion curves obtained for the phase velocity and the attenuation coefficient in a mixture of water with vapor–gas bubbles are compared for various values of vapor concentration in the bubbles and various bubble distributions in size. The evolution of pressure pulses of plane and cylindrical waves is demonstrated for different values of the initial vapor concentration in bubbles. The calculated frequency dependence of the phase sound velocity in a mixture of water with vapor bubbles is compared with experimental data.     

A probability density function of liftoff velocities in mixed-size wind sand flux

With the discrete element method (DEM), employing the diameter distribution of natural sands sampled from the Tengger Desert, a mixed-size sand bed was produced and the particle-bed collision was simulated in the mixed-size wind sand movement. In the simulation, the shear wind velocity, particle diameter, incident velocity and incident angle of the impact sand particle were given the same values as the experimental results. After the particle-bed collision, we collected all the initial velocities of rising sand particles, including the liftoff angular velocities, liftoff linear velocities and their horizontal and vertical components. By the statistical analysis on the velocity sample for each velocity component, its probability density functions were obtained, and they are the functions of the shear wind velocity. The liftoff velocities and their horizontal and vertical components are distributed as an exponential density function, while the angular velocities are distributed as a normal density function. Supported by the Key Project of the National Natural Science Foundation of China (Grant No. 10532040)     

Material property estimates from ultrasound attenuation in fibre suspensions

An investigation of a new method for measuring fibre material properties from ultrasonic attenuation in a dilute suspension of synthetic fibres of uniform geometry is presented. The method is based on inversely solving an ultrasound scattering and absorption model of suspended fibres in water for the material properties of the fibres. Experimental results were obtained from three suspensions of nylon 66 fibres each with different fibre diameters. A forward solution to the model with reference material values is compared to experimental data to verify the model’s behaviour. Estimates of the shear and Young’s modulus, the compressional wave velocity, Poisson’s ratio and loss tangent from nylon 66 fibres are compared to data available from other sources. Experimental data confirms that the model successfully predicts that the resonance features in the frequency response of the attenuation are a function of diameter. Consistent estimated values for the compressional wave velocity and the Poisson’s ratio were found to be difficult to obtain but in combination gave values of shear modulus within previously reported values and with low sensitivity to noise. Young’s modulus was underestimated by 54% but was consistent and had low sensitivity to noise. The underestimation is believed to be caused by the assumption of isotropic material used in the model. Additional tests on isotropic fibre would confirm this. Further analysis of the model sensitivity and the reasons for the resonance features are required.     

Turbulent statistical characteristics associated to the north wind phenomenon in southern Brazil with application to turbulent diffusion

A parameterization for the transport processes in a shear driven planetary boundary layer (PBL) has been established employing turbulent statistical quantities measured during the north wind phenomenon in southern Brazil. Therefore, observed one-dimensional turbulent energy spectra are compared with a spectral model based on the Kolmogorov arguments. The good agreement obtained from this comparison leads to well defined formulations for the turbulent velocity variance, local decorrelation time scale and eddy diffusivity. Furthermore, for vertical regions in which the wind shear forcing is relevant, the eddy diffusivity derived from the north wind data presents a similar profile to those obtained from the non-extensive statistical mechanics theory. Finally, a validation for the present parameterization has been accomplished, using a Lagrangian stochastic dispersion model. The Prairie Grass data set, which presents high mean wind speed, is simulated. The analysis developed in this study shows that the turbulence parameterization constructed from wind data for north wind flow cases is able to describe the diffusion in a high wind speed, shear-dominated PBL.     

激光雷达数据应用于海气界面气体传输速率的估算

选取2007年1、4、7、10月4个月夜间无云的云-气溶胶激光雷达和红外探测者观测卫星(CALIPSO)星载激光雷达Version 3.01数据,提取532nm激光海面后向散射系数并计算海面波浪均方斜率。同时选用准同步AMSR-E海面风速数据,利用Wanninkhof等于2009年提出的包含线性、平方、立方项的海面风速与气体传输速率混合关系模型计算海水施密特数为660时的海气界面气体传输速率k660。通过回归分析,得到由星载激光雷达数据反演k660的关系模型。将激光雷达数据反演结果与采用4种典型海面风速关系模型的计算结果进行比较,给出由星载激光雷达数据反演的4个月平均的海气界面气体传输速率全球分布图和纬度分布图。研究表明,CALIPSO星载激光雷达532nm单脉冲测量数据可用于反演海气界面气体传输速率。     

钨合金的高压本构研究

通过静高压实验、动高压实验及理论计算相结合的方法，确定了钨合金的一种高压本构方程 （Steinberg模型方程）中的各参数.用数值模拟计算方法，采用几种不同的本构模型进行了 计算，并与实测结果进行了比较.结果显示，确定的高压本构方程计算值与实测值符合最好. 关键词： 高压本构方程 Steinberg 模型 数值模拟计算 粒子速度波形     

Acoustic radiation from the elastic impact of a sphere with a slab

The transient sound radiation from the impact of a spherical object with a slab is analysed theoretically and compared with experimental results. It is shown that the major source of sound radiation when a sphere impinges on a massive plate is due to the sudden change of velocity of the sphere. By using the method of images, an analytical expression predicting the sound pressure waveform is obtained. Experimental results confirm the theoretical analysis and provide further explanation of this rigid body type of acoustic radiation.     

Quantitative analysis of PC MRI velocity maps: pulsatile flow in cylindrical vessels.

The accuracy of MR phase contrast (PC) velocity mapping, and the subsequent derivation of wall shear stress (WSS) values, has been quantitatively assessed. Using a retrospectively gated PC gradient-echo technique, the temporal-spatial velocity fields were measured for pulsatile flow in a rigid cylindrical vessel. The experimental data were compared with values derived from the Womersley solution of the Navier-Stokes equations. For a sinusoidal waveform, the overall root-mean-square (rms) difference between the measured and analytical velocities corresponded to 13% of the peak fluid velocity. The WSS derived from the data displayed a 14% rms difference with the analytical model. As an example of a more complicated flow, a triangular saw-tooth waveform was deconstructed into its Fourier components. Velocity maps and the WSS were calculated by the superposition of the individual solutions, weighted by the Fourier series coefficient, for each harmonic. The velocity and experimentally derived WSS agreed with the analytical results (4% and 12% rms difference, respectively). Evaluation of the analytical models allowed an estimate of the inherent accuracy in the measurement of velocity maps and WSS values.     

Velocity of weakly turbulent flames of finite thickness

The velocity increase of a weakly turbulent flame of finite thickness is investigated using analytical theory developed in previous papers. The obtained velocity increase depends on the flow parameters: on the turbulent intensity, on the turbulent spectrum and on the characteristic length scale. It also depends on the thermal and chemical properties of the burning matter: thermal expansion, the Markstein number and the temperature dependence of transport coefficients. It is shown that the influence of the finite flame thickness is especially strong close to the resonance point, when the wavelength of the turbulent harmonic is equal to the cut off wavelength of the Darrieus–Landau instability. The velocity increase is almost independent of the Prandtl number. On the contrary, the Markstein number is one of the most important parameters controlling the velocity increase. The relative role of the external turbulence and the Darrieus–Landau instability for the velocity increase is studied for different parameters of the flow and the burning matter. The velocity increase for turbulent flames in methane and propane fuel mixtures is calculated for different values of the equivalence ratio. The present theoretical results are compared with previous experiments on turbulent flames. In order to perform the comparison, the theoretical results of the present paper are extrapolated to the case of a strongly corrugated flame front using the ideas of self-similar flame dynamics. The obtained theoretical results are in a reasonable agreement with the experimental data, taking into account the uncertainties of both the theory and the experiments. It is shown that in many experiments on turbulent flames the Darrieus–Landau instability is more important for the flame velocity than the external turbulence.     

Photonic device as a second-order system

The present work presents the analysis of a photonic device. Starting from a laser model, it is shown that, if a two-level simplification is used and both low pumping and no losses are assumed, a second-order control system model is obtained. This model no longer describes a laser, but only a photonic device. The system response to a step input is analyzed and the results are compared with experimental data obtained when pumping a neodymium crystal with a diode laser. Both theoretical and experimental results are then compared with the analyzed photonic device. A good qualitative agreement is shown between the analytical, experimental, and computational results.     

Analytic prediction of unconfined boundary layer flashback limits in premixed hydrogen–air flames

Flame flashback is a major challenge in premixed combustion. Hence, the prediction of the minimum flow velocity to prevent boundary layer flashback is of high technical interest. This paper presents an analytic approach to predicting boundary layer flashback limits for channel and tube burners. The model reflects the experimentally observed flashback mechanism and consists of a local and global analysis. Based on the local analysis, the flow velocity at flashback initiation is obtained depending on flame angle and local turbulent burning velocity. The local turbulent burning velocity is calculated in accordance with a predictive model for boundary layer flashback limits of duct-confined flames presented by the authors in an earlier publication. This ensures consistency of both models. The flame angle of the stable flame near flashback conditions can be obtained by various methods. In this study, an approach based on global mass conservation is applied and is validated using Mie-scattering images from a channel burner test rig at ambient conditions. The predicted flashback limits are compared to experimental results and to literature data from preheated tube burner experiments. Finally, a method for including the effect of burner exit temperature is demonstrated and used to explain the discrepancies in flashback limits obtained from different burner configurations reported in the literature.     

Acoustic sounding of wind velocity profiles in a stratified moving atmosphere.

The paper deals with analytical and numerical studies of the effects of atmospheric stratification on acoustic remote sensing of wind velocity profiles by sodars. Both bistatic and monostatic schemes are considered. Formulas for the Doppler shift of an acoustic echo signal scattered by atmospheric turbulence advected with the mean wind in a stratified moving atmosphere are derived. Numerical studies of these formulas show that errors in retrieving wind velocity can be of the order of 1 m/s if atmospheric stratification is ignored. Formulas for the height at which wind velocity is retrieved are also derived. Approaches are proposed which allow one to take into account the effects of atmospheric stratification when restoring the wind velocity profile from measured values of the Doppler shift and the time interval of acoustic impulse propagation from a sodar to the scattering volume and back to the ground.