Magnetic and dielectric properties of low vanadium doped nickel-zinc-copper ferrites

The new spinel-type of general formula Ni_0.6+xZn_0.2Cu_0.2V_xFe_2−2xO₄ with 0.0≤x≤0.25 was synthesized by the usual ceramic method. Structure of the prepared ferrites was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX). Room temperature magnetic hysteresis loops were measured using magnetic field strength up to 6 kOe. Saturation magnetization (M_s) increased with vanadium content up to x=0.05 and then decreased. Variation of (M_s) as a function of x is explained in terms of cation redistribution between A and B sublattices. Coercive force (H_c), remanent induction (B_r) and squareness of the hysteresis loop (B_r/M_s) as functions of x are presented. Dielectric permittivity (ε′, ε″) and dielectric loss tangent (tan δ) were measured as functions of frequency and temperature. These parameters were found to be strongly dependent on V₂O₅ concentration. The variation of dielectric loss tangent with frequency at different temperatures shows abnormal behavior, where more than one relaxation peaks were observed at low and high temperatures. This behavior could be attributed to the collective contribution of two types of carriers (p and n) to polarization.     

Magnetic and dielectric properties of Ni0.8Co0.1Cu0.1Fe2O4+PZT composites

Magnetoelectric composites of Ni_0.8Co_0.1Cu_0.1Fe₂O₄ and Lead Zirconate Titanate (PZT) were prepared by using conventional ceramic method. The measured values of saturation magnetization (M_s) and magnetic moments (μ_B) are in accordance with the volume fraction of ferrite content in the composite. The dielectric constant of the composites decreases with frequency. The plots of dielectric constant () against temperature (T) show a peak at their respective transition temperatures. The ME output was measured by varying dc bias magnetic field. A large ME output signal of 776 mV/cm was observed for 35% ferrite +65% ferroelectric composite. The magnetoelectric (ME) response is found to be dependent on the content of ferrite phase.     

Structural characterization of dense reduced BaTiO3 and Ba0.95La0.05TiO3 nanoceramics showing colossal dielectric values

BaTiO_3−x and Ba_0.95La_0.05TiO_3−x nanoceramics showing colossal permittivity values have been characterized. While starting powders are of cubic symmetry, X-ray and Neutron Diffraction techniques and Raman Spectroscopy measurements show that the one-step processed ceramics obtained by Spark Plasma Sintering (SPS) contain cubic and tetragonal phases. Rather large oxygen deficiency determined in such ceramics by Electron Micro Probe analysis and Electron Energy Loss Spectroscopy analyzes is explained by the presence of Ti³⁺, as evidenced by X-ray Photoelectron Spectroscopy measurements. Transmission Electron Microscopy and High Resolution Transmission Electron Microscopy show that these ceramics contain 50-300 nm grains, which have single-domains, while grain boundaries are of nanometer scale. Colossal permittivity values measured in our dense nanoceramics are explained by a charge hopping mechanism and an interfacial polarization of a large number of polarons generated after sample reduction in SPS apparatus.     

Characterization, sintering and dielectric properties of nanocrystalline zinc oxide prepared by a citric acid-based combustion route

Nanosized zinc oxide has been synthesized through a novel single step solution combustion route using citric acid as fuel. The X-ray diffraction (XRD) analysis revealed that the synthesized ZnO nanopowder has the pure wurtzite structure. The phase purity of the nanopowder has been confirmed using differential thermal analysis (DTA), thermogravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FT-IR). The morphology and crystalline size of the as-prepared nanopowder characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed that the powder consisted of a mixture of nanoparticles and nanorods. The nanocrystalline ZnO could be sintered to ∼97% of the theoretical density at 1200 °C in 4 h. The dielectric constant (ε_r) and dielectric loss (ε_i) of sintered ZnO pellets at 5 MHz were 1.38 and 9×10⁻², respectively, at room temperature.     

Low temperature synthesis of Mn0.4Zn0.6In0.5Fe1.5O4 nanoferrite for high-frequency applications

In the present study, nanoferrite of composition Mn_0.4Zn_0.6In_0.5Fe_1.5O₄ has been synthesized by co-precipitation method. Decomposition of residue at a temperature as low as 200 °C gives the ferrite powder. The ferrite has been, finally, sintered at 500 °C. The structural studies have been made by using X-ray diffraction (XRD) technique and scanning electron microscopy (SEM), which confirm the formation of single spinel phase and nanostructure. The dc resistivity is studied as a function of temperature and values found are more than twice those for the samples prepared by the other chemical methods. It is found that the resistivity decreases with increase in temperature. The initial permeability value is found to be higher as compared to the other chemical routes. The initial permeability value is found to increase with increase in temperature. At a certain temperature called Curie temperature, it attains a maximum value, after which the initial permeability decreases sharply. Even at nanolevel, appreciable value of initial permeability is obtained and low magnetic losses make these ferrites especially suitable for high-frequency applications. The particle size is calculated using Scherrer's equation for Lorentzian peak, which comes out between 35 and 49 nm. Possible mechanisms contributing to these processes have been discussed.     

Preparation and characterization of surface modified γ-Fe2O3 (maghemite)-silica nanocomposites used for the purification of benzaldehyde lyase

γ-Fe₂O₃ (maghemite)-silica nanocomposite particles were synthesized using a sol-gel method. The condensation products of 3-glycidoxy propyltrimethoxy silane (GPTMS) and nitrilotriacetic acid (NTA) were introduced onto the surfaces of the γ-Fe₂O₃-silica nanocomposite particles and subsequently, these modified surfaces were complexed with cobalt (Co⁺²) metal ions. A possibility of using these surface modified γ-Fe₂O₃-silica particles for the purification of 6×histidine tagged recombinant benzaldehyde lyase (BAL, EC 4.1.2.38) based on magnetic separation was investigated. X-ray diffraction (XRD), thermal analysis, and vibrating sample magnetometry (VSM) methods were used to characterize the surface modified superparamagnetic γ-Fe₂O₃ (maghemite)-silica nanoparticles. XRD (Scherer's equation) results indicate that the primary particle size of maghemite was around 11 nm. Magnetic characterization results confirmed that the γ-Fe₂O₃ (maghemite)-silica nanoparticles were superparamagnetic. According to sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) results, these superparamagnetic nanoparticles specifically capture 6×His-tagged BAL from crude extract of Escherichia coli (E. coli) BL21(DE3)pLysS/BAL_HIS. This study shows that the surface modified γ-Fe₂O₃ (maghemite)-silica nanoparticles are eligible for immobilized metal-ion affinity adsorption for histidine tagged recombinant proteins with its high capacity (3.16±0.4 mg/g) and selectivity.     

Phase evolution and microwave dielectric properties of Bi3SbO7 ceramic

The Bi₃SbO₇ ceramic was prepared by the solid state reaction method and its phase evolution at different temperatures was studied. Low temperature phase α-Bi₃SbO₇ was formed at about 890 °C and it started to transform to high temperature phase β-Bi₃SbO₇ at about 960 °C. Microwave dielectric constants of α-Bi₃SbO₇ ceramic and β-Bi₃SbO₇ ceramic were 43.2 and 37.6, Qf value were 2080 and 5080 GHz, respectively. TCF of α-Bi₃SbO₇ ceramic was near zero and TCF of β-Bi₃SbO₇ ceramic was about −120 ppm/°C. The Bi₃SbO₇ ceramic is a promising candidate for low temperature co-fired ceramic (LTCC) technology due to its large dielectric constant, low dielectric loss at microwave region, low sintering temperature and simple composition.     

Magnetostriction of a single crystal of nickel observed with an X-ray four-circle goniometer

We proposed a technique to observe magnetostrictive coefficients of a single crystal specimen with X-ray diffraction. An angle between a direction of crystallographic orientation and a direction of magnetic field could be estimated with two kinds of diffraction peaks which were found with an X-ray four-circle goniometer. The magnetostriction was measured by a shift of Bragg angle. This technique was suitable for a case to observe the magnetostrictive coefficient which varied as a function of the magnetic field direction. We applied the technique to a single crystal specimen of nickel and showed dependences of the magnetostriction on the magnetic field strength and its direction around an axis of easy magnetization at room temperature.     

Improvement in electrical and magnetic properties of mixed Mg-Al-Mn ferrite system synthesized by citrate precursor technique

In the present work, mixed magnesium-manganese ferrites of composition Mg_0.9Mn_0.1Al_0.3Co_zFe_1.7−zO₄ where z=0.3, 0.5 and 0.7 have been synthesized by the citrate precursor technique. X-ray diffraction patterns of the samples confirmed the formation of single-phase spinel structure. The ferrites have been investigated for their electric and magnetic properties such as dc resistivity, Curie temperature, saturation magnetization, initial permeability and relative loss factor (RLF). Fairly constant value of initial permeability over a wide frequency range (0.1-20 MHz) and low values of the relative loss factor of the order of 10⁻⁴-10⁻⁵, in the frequency range 0.1-30 MHz, are the cardinal achievements of the present investigation. In addition to this, initial permeability was found to increase with an increase in temperature while RLF was observed to be low at these temperatures. The dc resistivity and Curie temperature were found to increase with an increase in cobalt content. The mechanisms contributing to these results are discussed in detail in this paper.     

Enhanced multiferroic properties in La and Ce co-doped BiFeO3 nanoparticles

Room temperature multiferroic properties of BiFeO₃ (BFO), Bi_0.9La_0.1FeO₃ ((La)BFO) and Bi_0.9La_0.075Ce_0.025FeO₃ ((La,Ce)BFO) nanoparticles have been reported in this paper. XRD (X-ray diffraction) analyses of the nanoparticles show a decrease in the lattice constants and cell volume with the substitution of La and Ce. It is evident from the SEM (scanning electron microscope) micrographs that the (La,Ce) co-doped sample possesses dense microstructure made of smaller particles. Raman study accounts for the weakening of the strong hybridization between Bi-O by the substitution of La and Ce ions. This is also accompanied by an increase in the remanent magnetization, dielectric constant, and ferroelectric polarization. BFO nanoparticles show exchange bias effect under an applied magnetic field while the (La)BFO and (La,Ce)BFO samples show no trace of such effect. Ac-conductivity of (La,Ce) co-doped sample is observed to be several orders lesser in magnitude than bulk BFO ceramics. These results are interpreted by means of the subtle change in the structure, suppression of the spin cycloid and reduction of oxygen vacancies in the doped samples.     

Orientation-dependent dielectric properties of Ba(Sn0.15Ti0.85)O3 thin films prepared by sol-gel method

The orientation-dependent dielectric properties of barium stannate titanate (Ba(Sn_0.15Ti_0.85)O₃, BTS) thin films grown on (1 0 0) LaAlO₃ single-crystal substrates through sol-gel process were investigated. The nonlinear dielectric properties of the BTS films were measured using an inter-digital capacitor (IDC). The results show that the in-plane dielectric properties of BTS films exhibited a strong sensitivity to orientation. The upward shift of Curie temperature (T_c) of the highly (1 0 0)-oriented BTS thin films is believed to be attributing to a tensile stress along the in-plane direction inside the film. A high tunability of 47.03% was obtained for the highly (1 0 0)-oriented BTS films, which is about three times larger than that of the BTS films with random orientation, measured at a frequency of 1 MHz and an applied electric field of 80 kV/cm. This work clearly reveals the highly promising potential of BTS films for application in tunable microwave devices.     

A systematic study on magnetic, dielectric and magnetocapacitance properties of Ni doped bismuth ferrite

In this paper we report the structural, magnetic, magnetocapacitance and dielectric properties of BiFe_1−xNi_xO₃ nanoceramics (with x=0, 0.1) prepared by the sol-gel method. XRD analysis showed formation of single phase nanoceramics (particle size ∼50 nm by TEM). Samples of BiFe_1−xNi_xO₃ were divided into two parts—one of them quenched in liquid nitrogen and another sintered in the normal way. We observed the enhancement in magnetic and dielectric properties of quenched sample. The splitting of zero field cool (ZFC) and field cool (FC) magnetization curves at low temperature reveals spin- glass behavior. Quenched sample showed the enhancement of blocking temperature.     

Magnetoelectric characterization of xNi0.75Co0.25Fe2O4-(1−x)BiFeO3 nanocomposites

Magnetoelectric (ME) nanocomposites containing Ni_0.75Co_0.25Fe₂O₄-BiFeO₃ phases were prepared by citrate sol-gel process. X-ray diffraction (XRD) analysis showed phase formation of xNi_0.75Co_0.25Fe₂O₄-(1−x)BiFeO₃ (x=0.1, 0.2, 0.3 and 0.4) composites on heating at 700 °C. Transmission electron microscopy revealed the formation of powders of nano order size and the crystal size was found to vary from 30 to 85 nm. Dispersion in dielectric constant (ε) and dielectric loss (tan δ) in the low-frequency range have been observed. It is seen that nanocomposites exhibit strong magnetic properties and a large ME effect. On increasing Ni_0.75Co_0.25Fe₂O₄ contents in the nanocomposites, the saturation magnetization (M_S) and coercivity (H_C) increased after annealing at 700 °C. The large ME output in the nanocomposites exhibits strong dependence on magnetic bias and magnetic field frequency. The large value of ME output can be attributed to small grain size of ferrite phase of nanocomposite being prepared by citrate precursor process.     

Structural, magnetic and electrical properties of NiCuZn ferrites prepared by microwave sintering method suitable for MLCI applications

Polycrystalline NiCuZn soft ferrites with stoichiometric iron were prepared by a novel microwave sintering method. The powders were calcined, compacted and sintered at 950 °C for 30 min in a microwave sintering furnace. X-ray diffraction patterns confirm the formation of single phase cubic spinel structure. The grain size was estimated using SEM micrographs. The lattice constant is found to increase with increase in zinc concentration. The sintered ferrites have been investigated for their physical, magnetic and electrical properties such as bulk density, X-ray density, porosity, anisotropy constant, initial permeability, saturation magnetization, DC resistivity, dielectric constant and dielectric loss as a function of zinc concentration. Permeability, saturation magnetization, dielectric constant and dielectric loss were found to increase while DC resistivity was found to decrease with the replacement of Zn with Ni. The present series of ferrites are found to posses properties that are suitable for the core materials in multilayer chip inductors.     

Synthesis and magnetic properties of the size-controlled Mn-Zn ferrite nanoparticles by oxidation method

Size-controlled Mn_0.67Zn_0.33Fe₂O₄ nanoparticles in the wide range from 80 to 20 nm have been synthesized, for the first time, using the oxidation method. It has been demonstrated that the particle size can be tailor-made by varying the concentration of the oxidant. The magnetization of the 80 nm particles was 49 A m² kg⁻¹ compared to 34 A m² kg⁻¹ for the 20 nm particles. The Curie temperatures for all the samples are found to be within 630±5 K suggesting that there is no size-dependent cation distribution. The critical particle size for the superparamagnetic limit is found to be about 25 nm. The effective magnetic anisotropy constant is experimentally determined to be 7.78 kJ m⁻³ for the 25 nm particles, which is about an order of magnitude higher than that of the bulk ferrite.     

Influence of Ca additives on the optical and dielectric studies of sol-gel derived PbTiO3 ceramics

Sintered ceramic powders of calcium-doped lead titanate [Pb_1−xCa_xTiO₃] ceramics with different Ca dopant concentration in the range (x=0-0.35) have been prepared using a sol-gel chemical route. The sol-gel technique is known to offer better purity and homogeneity, and can yield stoichiometric powders with improved properties at relatively lower processing temperature in comparison to conventional solid-state reaction. X-ray diffraction (XRD) and Raman spectroscopy studies have been carried out to identify the crystallographic structure and phase formation. The infrared absorption spectra in the mid-IR region (400-4000 cm⁻¹) show the band corresponding to the Ti-O bond at ∼576 cm⁻¹ and is found to shift to a higher wave number 592 cm⁻¹ with increasing Ca content. The dielectric properties as a function of frequency, and phase transition studies on sintered ceramic Pb_0.65Ca_0.35TiO₃ has been investigated in detail over a wide temperature range 30-600 °C and the results are discussed.     

Densification, microstructural evolution, and dielectric properties of CaTiO3-LaGaO3 microwave ceramics

The relations among the densification, microstructural evolution, and microwave dielectric properties of the (1−x)CaTiO₃-xLaGaO₃ ceramics with x=0.34 and 0.36 were investigated in this study. The results indicated that (1−x)CaTiO₃−xLaGaO₃ ceramics can be densified at 1300 °C with at least 97% of the theoretical value. The ceramics reported an orthorhombic perovskite structure, and no other detectable phases were found. Both ε_r and Q×f values can be improved by slowing the cooling rate during sintering. The ε_r and Q×f values of the 0.64CaTiO₃-0.36LaGaO₃ ceramics at cooling rates of >10 °C/min and 0.1 °C/min are 48.1 and 27,500 and 48.7 and 38,000, respectively. The higher densification obtained at a slower cooling rate plays an important role in improving the microwave dielectric properties.     

Microstructural, dielectric and spectroscopic properties of Li2O-Nb2O5-ZrO2-SiO2 glass system crystallized with V2O5

Li₂O-Nb₂O₅-ZrO₂-SiO₂ glasses mixed with different concentrations of V₂O₅ were crystallized. The samples were characterized by XRD, SEM and DTA techniques. The SEM pictures indicated that the samples contain well defined and randomly distributed crystal grains. The X-ray diffraction studies have revealed the presence of several crystalline phases in these samples. Optical absorption, ESR and photoluminescence spectral studies on these samples have indicated that a considerable proportion of vanadium ions do exist in V⁴⁺ state in addition to V⁵⁺ state and the redox ratio seems to be increasing with increase in the concentration of crystallizing agent V₂O₅. The infrared spectral studies have pointed out the existence of conventional SiO₄, ZrO₄, NbO₆, VO structural units in the glass ceramic network. The study of dielectric properties suggested a decrease in the insulating character of the glass ceramics with increase in the crystallizing agent. A.C. conductivity in the high temperature region seems to be connected mainly with the polarons involved in the process of transfer from V⁴⁺↔V⁵⁺ ions.     

Studies of dielectric and impedance properties of KCa2V5O15 ceramics

A polycrystalline sample, KCa₂V₅O₁₅, with tungsten bronze structure was prepared by a mixed-oxide method at low temperature (i.e., at 630 °C). A preliminary structural analysis of the compound showed an orthorhombic crystal structure at room temperature. Surface morphology of the compound was studied by scanning electron microscopy (SEM). Two dielectric anomalies at 131 and 275 °C were observed in the temperature dependency of dielectric response at various frequencies, which may be attributed to the ferroelastic-ferroelectric and ferroelectric-paraelectric transitions, respectively. The nature of variation of the electrical conductivity, and value of activation energy of different temperature regions, suggest that the conduction process is of mixed-type (i.e., ionic-polaronic and space charge generated from the oxygen ion vacancies). The impedance plots showed only bulk contributions, and non-Debye type of relaxation process occurs in the material. A hopping mechanism of electrical transport processes in the system is evident from the modulus analysis. The activation energy of the compound (calculated both from loss and modulus spectrum) is same, and hence the relaxation process may be attributed to the same type of charge carriers.     

Microstructure and piezoelectric properties of Bi0.5(Na0.82K0.18)0.5TiO3−NaSbO3 ceramics

Lead-free piezoelectric ceramics (1−x)Bi_0.5(Na_0.82K_0.18)_0.5TiO₃−xNaSbO₃ have been prepared by a conventional ceramics technique, and their microstructure and electrical properties have been investigated. The addition of NaSbO₃ has no remarkable effect on the crystal structure within the studied doping content; however, an obvious change in microstructure took place. With increase in NaSbO₃ content, the temperature from a ferroelectric to antiferroelectric phase transition increases, and the temperature for a transition from antiferroelectric phases to paraelectric phases changes insignificantly. Simultaneously, the temperature range between the rhombohedral phase transition point and the Curie temperature point becomes smaller. The piezoelectric properties significantly increase with increase in NaSbO₃ content and the piezoelectric constant and electromechanical coupling factor attain maximum values of d₃₃=160 pC/N and k_p=0.333 at x=0.01. The results indicate that (1−x)Bi_0.5(Na_0.82K_0.18)_0.5TiO₃−xNaSbO₃ ceramic is a promising lead-free piezoelectric candidate material.