Comparative investigation on spectroscopic properties of Er between Ce-doped and B2O3-added bismuth glasses

The comparative investigation on the spectroscopic properties of Er³⁺ in low phonon energy Bi₂O₃-GeO₂-Ga₂O₃-Na₂O glasses codoped with Ce³⁺ ion and added with B₂O₃ component, respectively, is presented. With increasing Ce₂O₃ content from 0 to 0.8 mol% or B₂O₃ content from 0 to 15 mol%, the lifetime of Er³⁺:⁴I_11/2 level decreases dramatically from 607 to 283 μs or to 197 μs, and the upconversion fluorescence is quenched in both glass samples. The nonradiative energy transfer from Er³⁺:⁴I_11/2→Ce³⁺:²F_5/2 or the enhanced multiphonon relaxation process together with the energy transfer between Er³⁺ and OH⁻ groups are, respectively, responsible for the results. Meanwhile, the lifetime of ⁴I_13/2 level remains almost unchanged in Er³⁺/Ce³⁺-codoped glasses whereas it decreases rapidly in B₂O₃-added cases. As a result, Er³⁺/Ce³⁺ codoping improves the 1.5 μm fluorescence emission intensity, however, B₂O₃ addition has a negative effect on it. The research results indicate that the Er³⁺/Ce³⁺-codoped bismuth glasses will be preferable for obtaining efficient 980 nm pumped EDFA.     

Effect of Bi2O3 on EPR, optical transmission and DC conductivity of vanadyl doped alkali bismuth borate glasses

Glasses with composition xBi₂O₃·(30−x)M₂O·70B₂O₃ (M=Li, Na) containing 2 mol% V₂O₅ have been prepared over the range 0≤x≤15 (x is in mol%). The electron paramagnetic resonance spectra of VO²⁺ of these glasses have been recorded in the X-band (≈9.3 GHz) at room temperature (RT≈300 K). Spin Hamiltonian parameters, g_∥, g_⊥, A_∥, A_⊥, dipolar hyperfine coupling parameter, P, and Fermi contact interaction parameter, K, have been calculated. The molecular orbital coefficients, α² and γ², have been calculated by recording the optical transmission spectra. In xBi₂O₃·(30−x)Li₂O·70B₂O₃ glasses there is decrease in the tetragonality of the V⁴⁺O₆ complex for x up to 6 mol% whereas for x≥6 mol%, tetragonality increases. In xBi₂O₃·(30−x)Na₂O·70B₂O₃ glasses there is increase in the tetragonality of the V⁴⁺O₆ complex with increasing x. The 3d_xy orbit expands with increase in Bi₂O₃:M₂O ratio. Values of the theoretical optical basicity, Λ_th, have also been reported. The DC conductivity increases with increase in temperature. The order of conductivity is 10⁻⁵ ohm⁻¹ m⁻¹ at low temperature and 10⁻³ ohm⁻¹ m⁻¹ at high temperature. The DC conductivity decreases and the activation energy increases with increase in Bi₂O₃:M₂O ratio.     

Optical absorption spectrum of Cu2O-CaO-P2O5 glasses

Homogeneous CaO-P₂O₅ and Cu₂O-CaO-P₂O₅ glasses were prepared using a melt-quenched method under controlled conditions. The binary glasses were found to be colourless and transparent while the ternary glasses changed from light green to dark green as the Cu₂O content increased. From the absorption edge studies, the values of the optical band gap, E_opt and Urbach energy, ΔE were evaluated. The position of the absorption edge and hence the optical band gap were found to depend on the glass composition. Analysis of the optical band gap shows that for the binary glasses, the value increases as the content of CaO decreases, while for the ternary glasses, the value of the optical band gap increases as the content of the Cu₂O decreases. The density of the glasses was also measured and was found to increase with the increase in CaO and Cu₂O contents.     

The photoluminescent properties of Eu in MgO-Ga2O3-SiO2 nanocrystalline glass-ceramic

The MgO-Ga₂O₃-SiO₂ glass-ceramic (GC) containing MgGa₂O₄ nanocrystals and glasses doped with Eu³⁺ ions were prepared by the sol-gel method. The down-conversion and up-conversion luminescence (UCL) properties were studied. The results indicated that the relative intensity of f-f transitions of Eu³⁺ decreased in contrast with that of charge transfer (CT) absorption with the increase in heating temperature. Using a Xe lamp and 800 nm femtosecond (fs) laser excitation, strong red luminescence of Eu³⁺ in MgO-Ga₂O₃-SiO₂ glasses and GC was observed.     

Dielectric relaxation and a.c. conduction phenomena of PbO-PbF2-B2O3 glasses doped with FeO

PbO-PbF₂-B₂O₃ glasses containing different concentrations of FeO have been prepared. The glasses are characterized by X-ray diffraction and differential thermal analysis. The dielectric properties viz., dielectric constant, loss, conductivity, over a moderately wide range of frequency and temperature and dielectric breakdown strength have been investigated. The results of these studies have been analyzed in the light of different oxidation states of iron with the aid of the data on IR, ESR, optical absorption and magnetic susceptibility measurements. The analysis shows that iron ions exist mainly in Fe³⁺ state, occupy tetrahedral positions and increase the insulating strength of the glass if FeO is present in smaller concentrations. However, if FeO is present in higher concentrations in the glass matrix, (i) the dielectric relaxation intensity has been observed to increase, (ii) the intensity and the half width of the ESR signal has been observed to decrease and (iii) the value of magnetic moment (evaluated from magnetic susceptibility) has been observed to drop to a value of 4.6 μ_B from 5.7 μ_B. From these results it has been concluded that in this concentration range, iron ions exist mainly in divalent state.     

Effect of ZnO/CdO on the structure and electrical conductivity in Li2O·MO·Bi2O3·B2O3 glasses (M=Zn, Cd)

Studies of structural and electrical properties have been carried out on a number of glasses with wide ranging compositions in the glass systems Li₂O·MO·Bi₂O₃·B₂O₃ (where M=Zn or Cd), in order to understand the effect of transition metal (TM) ions on the structure of these glasses. The density and molar volume measurements have also been made to understand the structural changes occurring in these glasses. The dc conductivity measured in the temperature range 423-623 K obeys Arrhenius law. It increases with increase in Li₂O/MO ratio. The results of infrared spectra indicate that TM ions (Zn²⁺ or Cd²⁺) behave as network former in the present system. Boron exists in both tri- and tetra-hedral units in these glasses and no boroxol ring formation takes place in the glass structure. Values of theoretical optical basicity have also been reported.     

EPR and optical studies on transition metal doped LiRbB4O7 glasses

Electron paramagnetic resonance and optical investigations of copper and chromium doped LiRbB₄O₇ glasses are carried out. From the results and discussions, it is predicted that both the transition metal ions exhibit octahedral environment. In the case of Cr³⁺, the site symmetry is near octahedral, whereas in the case of Cu²⁺, it is tetragonally distorted octahedral environment. Crystal field, spin-Hamiltonian and bonding parameters are evaluated. The bonding parameters are suggesting ionic.     

Microstructural, dielectric and spectroscopic properties of Li2O-Nb2O5-ZrO2-SiO2 glass system crystallized with V2O5

Li₂O-Nb₂O₅-ZrO₂-SiO₂ glasses mixed with different concentrations of V₂O₅ were crystallized. The samples were characterized by XRD, SEM and DTA techniques. The SEM pictures indicated that the samples contain well defined and randomly distributed crystal grains. The X-ray diffraction studies have revealed the presence of several crystalline phases in these samples. Optical absorption, ESR and photoluminescence spectral studies on these samples have indicated that a considerable proportion of vanadium ions do exist in V⁴⁺ state in addition to V⁵⁺ state and the redox ratio seems to be increasing with increase in the concentration of crystallizing agent V₂O₅. The infrared spectral studies have pointed out the existence of conventional SiO₄, ZrO₄, NbO₆, VO structural units in the glass ceramic network. The study of dielectric properties suggested a decrease in the insulating character of the glass ceramics with increase in the crystallizing agent. A.C. conductivity in the high temperature region seems to be connected mainly with the polarons involved in the process of transfer from V⁴⁺↔V⁵⁺ ions.     

Crystal field analysis of the absorption spectra and electron-phonon interaction in Ca3Sc2Ge3O12:Ni

Exchange charge model of crystal field [B.Z. Malkin, in: A.A. Kaplyanskii, B.M. Macfarlane (Eds.), Spectroscopy of Solids Containing Rare-earth Ions, North-Holland, Amsterdam, 1987, pp. 33-50.] was used to analyze the energy level schemes of Ni²⁺ ion at both possible positions (octahedral and tetrahedral) in Ca₃Sc₂Ge₃O₁₂. The crystal field parameters were calculated from the crystal structure data; the crystal field Hamiltonian was diagonalised in the complete basis consisting of 25 wave functions of all LS terms of the Ni²⁺ ion. Results of calculations are in a good agreement with experimental data. From the experimental spectra available in the literature, the Huang-Rhys parameter S=3.5 and effective phonon energy were evaluated for the octahedral Ni²⁺ ion.     

Enhanced luminescence from transparent Ni-doped MgO–Al2O3–SiO2 glass ceramics by Ga2O3 addition

Transparent Ni²⁺-doped MgO–Al₂O₃–SiO₂ glass ceramics without and with Ga₂O₃ were synthetized. The precipitation of spinel nanocrystals, which was identified as solid solutions in the glass ceramics, could be favored by Ga₂O₃ addition and their sizes were about 7.6 nm in diameter. The luminescent intensity of the Ni²⁺-doped glass ceramics was largely enhanced by Ga₂O₃ addition which could mainly be caused by increasing of Ni²⁺ in the octahedral sites and the reduction of the mean frequency of phonon density of states in the spinel nanocrystals of solid solutions. The full width at half maximum (FWHM) of emissions for the glass ceramics with different Ga₂O₃ content was all more than 200 nm. The emission lifetime increased with the Ga₂O₃ content and the longest lifetime is about 250 μs. The Ni²⁺-doped transparent glass ceramics with Ga₂O₃ addition have potential application as broadband optical amplifier and laser materials.     

Dielectric spectroscopy on Bi3Zn2Sb3O14 ceramic: an approach based on the complex impedance

The dielectric properties and loss of Bi_1.5ZnSb_1.5O₇ a poor-semiconducting ceramic were investigated by impedance spectroscopy, in the frequency range from 5 Hz to 13 MHz. Electric measurements were performed from 100 to 700 °C. Pyrochlore type phase was synthesized by the polymeric precursor method. Dense ceramic with 97% of the theoretical density was prepared by sintering via constant heating rate. The dielectric permittivity dependence as a function of frequency and temperature showed a strong dispersion at frequency lower than 10 kHz. The losses exhibit slight dependence with the frequency at low temperatures presenting a strong increase at temperatures higher than 400 °C. A decrease of the loss magnitude occurs with increasing frequency. Relaxation times were extracted using the dielectric functions Z″(ω) and M″(ω). The plots of the relaxation times τ_Z′ and τ_M″ as a function of temperature follow the Arrhenius law, where a single slope is observed with activation energy values equal to 1.38 and 1.37 eV, respectively.     

Studies on the influence of lithium incorporation in the photoluminescence of Y2O3:Eu thin films

Nanostructured europium-doped yttrium oxide thin films with lithium as a co-dopant were prepared using pulsed laser ablation technique. X-ray diffraction studies of the films indicated amorphous nature of the as deposited films and a transformation to crystalline phase with increase of annealing temperature. In this transformation, lithium co-doped films showed early crystallization. Lithium substitution resulted not only in enhancement of photoluminescence at 612 nm, resulting from ⁵D₀-⁷F₂ transition within europium, but also found to reduce the required processing temperature for intense photoemission. The deviation observed in the value of lattice constant of films annealed at different temperatures is found to be sensitive to annealing temperature. In the light of this, the dependence of photoluminescence intensity on the magnitude of lattice imperfection is also discussed. The morphology and transmittance of the films are also found to be sensitive to annealing process and lithium doping.     

Third-order nonlinear optical properties of Bi2S3 and Sb2S3 nanorods studied by the Z-scan technique

Bismuth sulfide (Bi₂S₃) and antimony sulfide (Sb₂S₃) nanorods were synthesized by hydrothermal method. The products were characterized by UV-vis spectrophotometer, X-ray powder diffraction (XRD) and transmission electron microscope (TEM). Bi₂S₃ and Sb₂S₃ nanorods were measured by Z-scan technique to investigate the third-order nonlinear optical (NLO) properties. The result of NLO measurements shows that the Bi₂S₃ and Sb₂S₃ nanorods have the behaviors of the third-order NLO properties of both NLO absorption and NLO refraction with self-focusing effects. The third-order NLO coefficient χ⁽³⁾ of the Bi₂S₃ and Sb₂S₃ nanorods are 6.25×10⁻¹¹ esu and 4.55×10⁻¹¹ esu, respectively. The Sb₂S₃ and Bi₂S₃ nanorods with large third-order NLO coefficient are promising materials for applications in optical devices.     

Synthesis,photophysical properties,and photocatalytic applications of Bi doped NaTaO3 and Bi doped Na2Ta2O6 nanoparticles

Phase formation and photophysical properties of bismuth doped sodium tantalum oxide (perovskite, defect pyrochlore) nanoparticles prepared by a hydrothermal method were studied in detail. It was revealed that the synthesis conditions like NaOH concentration and bismuth precursor (NaBiO₃·2H₂O) markedly affect the crystal structure of sodium tantalum oxide. At low NaOH concentration and high bismuth precursor (NaBiO₃·2H₂O) content, Bi doped Na₂Ta₂O₆ (defect pyrochlore) phase was predominantly formed, while at higher NaOH concentration, Bi doped NaTaO₃ (perovskite) phase was formed. It was observed that the defect pyrochlore (Bi doped Na₂Ta₂O₆) phase was formed and stabilized by the presence of dopant precursor (NaBiO₃·2H₂O). The chemical analysis of the samples confirmed the doping of Bi³⁺ cations in both phases. Doping of bismuth enabled visible light absorption up to 500 nm in perovskite and defect pyrochlore type sodium tantalum oxide. Bi doped NaTaO₃ samples showed better performance for the photocatalytic degradation of rhodamine B than that of Bi doped Na₂Ta₂O₆, under visible light irritation (λ>420 nm). The present results shed light on phase formation of sodium tantalate and these results are useful in understanding properties of NaTaO₃ based compounds, synthesized by the hydrothermal method.     

Investigation of spectroscopic properties and thermal stability of Er/Yb-co-doped Bi2O3-B2O3-Ga2O3 glasses

A series of Er³⁺/Yb³⁺-co-doped 60Bi₂O₃-(40−x) B₂O₃ -xGa₂O₃ (BBGA x=0, 4, 8, 12, 16 mol%) glasses have been prepared. The absorption spectra, emission spectra, fluorescence lifetime of Er³⁺:⁴I_13/2 level and thermal stability were measured and investigated. Three Judd-Ofelt intensity parameters Ω_t (t=2,4,6) (Ω₂=(4.67-5.93)×10⁻²⁰ cm², Ω₄=(1.50-1.81)×10⁻²⁰ cm², Ω₆=(0.92-1.17)×10⁻²⁰ cm²) of Er³⁺ ions were calculated by Judd-Ofelt theory. It is found that the Ω₆ first increases with the increase of Ga₂O₃ content from 0 to 8 mol% and then decreases, which is mainly affected by the number of non-bridging oxygen ions of the glass network. The high peak of stimulated emission cross-section () of Er³⁺: ⁴I_13/2→⁴I_15/2 transition were obtained according to McCumber theory and broad full width at half maximum (FWHM=69-76 nm) of the ⁴I_13/2→⁴I_15/2 transition of Er³⁺ ions were measured. The results indicate that these new BBGA glasses can be used as a candidate host material for potential broadband optical amplifiers.     

The influence of different fabrication processes on characteristics of excess Bi2O3-doped 0.95 (Na0.5Bi0.5)TiO3–0.05 BaTiO3 ceramics

In this study, we will develop the influences of the excess x wt% (x=0, 1, 2, and 3) Bi₂O₃-doped and the different fabricating process on the sintering and dielectric characteristics of 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃ ferroelectric ceramics with the aid of SEM and X-ray diffraction patterns, and dielectric–temperature curves. The 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ ceramics are fabricated by two different processes. The first process is that (Na_0.5Bi_0.5)TiO₃ composition is calcined at 850 °C and BaTiO₃ composition is calcined at 1100 °C, then the calcined (Na_0.5Bi_0.5)TiO₃ and BaTiO₃ powders are mixed in according to 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ compositions. The second process is that the raw materials are mixed in accordance to the 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ compositions and then calcining at 900 °C. The sintering process is carried out in air for 2 h from 1120 to 1240 °C. After sintering, the effects of process parameters on the dielectric characteristics will be developed by the dielectric–temperature curves. Dielectric–temperature properties are also investigated at the temperatures of 30–350 °C and at the frequencies of 10 kHz–1 MHz.     

Optical spectroscopy of Yb/Er codoped NaY(WO4)2 crystal

Erbium and ytterbium codoped double tungstates NaY(WO₄)₂ crystals were prepared by using Czochralski (CZ) pulling method. The absorption spectra in the region 290-2000 nm have been recorded at room temperature. The Judd-Ofelt theory was applied to the measured values of absorption line strengths to evaluate the spontaneous emission probabilities and stimulated emission cross sections of Er³⁺ ions in NaY(WO₄)₂ crystals. Intensive green and red lights were measured when the sample were pumped by a 974 nm laser diode (LD), especially, the intensities of green upconversion luminescence are very strong. The mechanism of energy transfer from Yb³⁺ to Er³⁺ ions was analyzed. Energy transfer and nonradiative relaxation played an important role in the upconversion process. Photoexcited luminescence experiments are also fulfilled to help analyzing the transit processes of the energy levels.     

Photoluminescence spectra of rare earth doped CaGa2S4 single crystals

Six kind CaGa₂S₄ single crystals doped with different rare earth (RE) elements are grown by the horizontal Bridgman method, and their photoluminescence (PL) spectra are measured in the temperature range from 10 to 300 K. The PL spectra of Ce or Eu doped crystals have broad line shapes due to the phonon assisted 4f-5d transitions. On the other hand, those of Pr³⁺, Tb³⁺, Er³⁺ or Tm³⁺ doped samples show narrow ones owing to the 4f-4f transitions. The assignments of the electronic levels are made in reference to the reported data of RE 4f multiplets observed in same materials.     

Thermoluminescence studies of LiBa2B5O10:RE (RE=Dy, Tb and Tm)

LiBa₂B₅O₁₀:RE³⁺ (RE=Dy, Tb and Tm) was synthesized by the method of high-temperature solid-state reaction and the thermoluminescence (TL) properties of the samples under the irradiation of the γ-ray were studied. The result showed that Dy³⁺ ion was the most efficient activator. When the concentration of Dy³⁺ was 2 mol%, LiBa₂B₅O₁₀:Dy³⁺ exhibited a maximum TL output. The kinetic parameter of LiBa₂B₅O₁₀:0.02Dy was estimated by the peak shape method, for which the average activation energy was 0.757 eV and the frequency factor was 1.50×10⁷ s⁻¹. By the three-dimensional (3D) TL spectrum, the TL of the sample was contributed to the characteristic f-f transition of Dy³⁺. The dose-response of LiBa₂B₅O₁₀:0.02Dy to γ-ray was linear in the range from 1 to 1000 mGy. In addition, the decay of the TL intensity of LiBa₂B₅O₁₀:0.02Dy was also investigated.