Molecular materials derived from MPc (M=Fe, Pb, Co) and 1,8-dihydroxiantraquinone thin films: Formation, electrical and optical properties

Semiconductor-like thin films were grown using metallic phthalocyanines (MPc) (M=Fe, Pb, Co) and 1,8 dihydroxiantraquinone as initial compounds. The morphology of the deposited films was studied by using scanning electron microscopy and atomic force microscopy. The powder and thin-film samples of the synthesized materials, deposited by vacuum thermal evaporation, showed the same intra-molecular bonds as in IR spectroscopy studies, which suggests that the evaporation process does not alter these bonds. The optical band gap values of C₆₀H₂₈N₈O₈Fe, C₆₀H₂₈N₈O₈Pb and C₆₀H₂₈N₈O₈Co calculated from the absorption coefficient were found to be 1.60, 1.89 and 1.75 eV, respectively, arising from non-direct transitions. The effect of temperature on conductivity was also measured in these samples. It was found that the temperature-dependent electric current in all cases showed a semiconductor behavior with conductivities in the order of 10⁻⁶ Ω⁻¹ cm⁻¹ where the highest value corresponded to the cobalt material. The linear dependence observed in the films implies only one type of conduction mechanism in all cases, with mean activation energies of the order of 1.55, 1.77 and 1.50 eV for iron, lead and cobalt-based thin films, respectively.     

Improved dielectric properties of (Pb,Ca)TiO3 thin films prepared by metal-organic decomposition method

(Pb,Ca)TiO₃ (PCT) thin films have been deposited on Pt/Ti/SiO₂/Si substrate by metal-organic decomposition (MOD) technique. The film processing parameters such as drying and annealing temperatures have been optimized to obtain good-quality PCT films. Compositional analysis of the film has been studied by X-ray photoelectron spectroscopy (XPS). The effect of the annealing temperature on the crystalline structure, microstructure and electrical properties have been investigated by X-ray diffraction, atomic force microscopy (AFM) and impedance analyzer, respectively. Amorphous PCT films form at 350 °C and crystallize in the perovskite phase following the isothermal annealing at ?650 °C for 3 h in oxygen ambient. Typical tetragonal structure of the PCT film is evidenced from X-ray diffraction pattern. The grain size in the PCT films increases with an increase in annealing temperature. Significant improvement in the dielectric constant value is observed as compared to other reported work on PCT films. The observed dielectric constant and dissipation factor at 100 kHz for 650 °C annealed PCT films are 308 and 0.015, respectively. The correlation of the film microstructural features and electrical behaviors is described.     

A study of structural, compositional and optical properties of spray-deposited non-stoichiometric (Zn,Fe)S thin films

Non-stoichiometric ternary chalcogenides (Zn,Fe)S were prepared in the film form by pyrolytic spray deposition technique, using air/nitrogen as the carrier gas. The precursor solution comprised of ZnCl₂, FeCl₂ and thiourea. The depositions were carried out under optimum conditions of experimental parameters viz. carrier gas (air/nitrogen) flow rate, concentration of precursor constituents, nozzle substrate distance and temperature of quartz substrate. The deposited thin films were later sintered in argon at 1073 K for 120 min.The structural, compositional and optical properties of the sintered thin films were studied. X-ray diffraction studies of the thin films indicated the presence of (Zn,Fe)S solid solution with prominent cubic sphalerite phase while surface morphology as determined by scanning electron microscopy (SEM) revealed a granular structure.The chemical composition of the resulting thin films as analyzed by energy dispersive X-ray analysis (EDAX) reflected the composition of the precursor solutions from which the depositions were carried out with Fe at% values ranging from 0.4 up to 33.SEM micrographs of thin films reveal that the grain sizes of the thin films prepared using air as carrier gas and N₂ as carrier gas are in the vicinity of 300 and 150 nm, respectively.The diffuse transmittance measurements for thin films, as a function of wavelength reveal the dependence of direct optical band gap on Fe content and type of phase.     

Effect of indium doping in CdO thin films prepared by spray pyrolysis technique

Preparation of transparent and conducting indium doped CdO thin films by spray pyrolysis on glass substrate is reported for various concentration of indium (2-8 wt%) in the spray solution. The electrical, optical and structural properties of indium doped CdO films were investigated using different techniques such as Hall measurement, optical transmission, X-ray diffraction and scanning electron microscope. X-ray analysis shows that the undoped CdO films are preferentially orientated along (2 0 0) crystallographic direction. Increase of indium doping concentration increases the films packing density and reorient the crystallites along (1 1 1) plane. A minimum resistivity of 4.843×10⁻⁴ Ω cm and carrier concentration of 3.73×10²⁰ cm⁻³ with high transmittance in the range 300-1100 nm were achieved for 6 wt% indium doping. The band gap value increases with doping concentration and reaches a maximum of 2.72 eV for 6 wt% indium doping from 2.36 eV of that of undoped film. The minimum resistivity achieved in the present study is found to be the lowest among the reported values for In-doped CdO films prepared by spray pyrolysis method.     

Structural, electrical and optical properties of AgInS2 thin films grown by thermal evaporation method

Structural electrical and optical properties of AgInS₂ (AIS) thin films grown by the single-source thermal evaporation method were studied. The X-ray diffraction spectra indicated that the AIS single phase was successful grown by annealing above 400 °C in air. The AIS grain sizes became large with increasing the annealing temperatures. All polycrystalline AIS thin films were sulfur-poor from the electron probe microanalysis and indicated n-type conduction by the Van der Pauw technique. It was deduced that the sulfur vacancies were dominant in the films and enhanced n-type conduction.     

Structure and optical properties of chemically synthesized titanium oxide deposited by evaporation technique

Titanium oxide inorganic ion exchange material was synthesized by hydrolysis with water and ammonia solution. Structural feature of the synthesized titanium oxide was analyzed using X-ray diffraction, X-ray fluorescence and infrared spectrometer technique. Tentative formula of titanium oxide was determined and written as TiO₂·0.58H₂O. Titanium oxide films were deposited on glass substrates by means of an electron beam evaporation technique at room temperature from bulk sample. The films were annealed at 250, 350, 450, and 550 °C temperatures. Transmittance, reflectance, optical energy gap, refractive index and extinction coefficient were investigated. The transmittance values of 85% in the visible region and 88% in the near infrared region have been obtained for titanium oxide film annealed at 550 °C. Kubelka-Munk function was used to evaluate the absorption coefficient which was used to determine the optical band gap. It was found that the optical band gap increases with increasing annealing temperature whereas the refractive index and extinction coefficient decreases.     

Electrical and optical properties of GexFexSe100−2x chalcogenide thin films

Optical absorption at room temperature and electrical conductivity at temperatures between 283 and 333 K of vacuum evaporated Ge_xFe_xSe_100−2x (0≤x≤15) amorphous thin films have been studied as a function of composition and film thickness. It was found that the optical absorption is due to indirect transition and the energy gap increases with increasing both Ge and Fe content; on the other hand, the width of the band tail exhibits the opposite behavior. The optical band gap E_opt was found to be almost thickness independent. The electrical conductivity show two types of conduction, at higher temperature the conduction is due to extended states, while the conduction at low temperature is due to variable range hopping in the localized states near Fermi level. Increasing Ge and Fe contents were found to decrease the localized state density N(E_F), electrical conductivity and increase the activation energy for conduction, which is nearly thickness independent. Variation of the atomic densities ρ, molar volume V, glass transition temperature T_g cohesive energy C.E and number of constraints N_Co with average coordination number Z was investigated. The relationship between the optical gap and chemical composition is discussed in terms of the cohesive energy C.E, average heat of atomization and coordination numbers.     

Electrical and magnetic properties of Ni-Cu-Si heterojunction prepared by the liquid phase epitaxy technique

Ni-Cu-Si heterojunction was prepared by the liquid phase epitaxy (LPE) technique. Two growth solutions containing Indium (In) with Cu pieces and In with Ni pieces were employed during the fabrication process. The as-formed junction was directly characterized by different techniques including scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and thin film X-ray diffraction (XRD) measurements. The current-voltage (I-V) characteristics of the Au/Ni/Cu/Si diode were found to be nonlinear, asymmetric, having a good rectification behavior with a very small leakage current of 0.003 μA at a reverse bias voltage of 2.0 V. The value of turn on voltage was located at 0.2 V. The magnetic properties were also evaluated at room temperature with a vibrating sample magnetometer. Systematic study of junction fabrication and characterization of such a heterosystem, comparison of the behavior of flat silicon and nanoporous silicon as substrates are presented and thoroughly discussed.     

Leakage current, ferroelectric and structural properties in Pb1−xBaxTiO3 thin films prepared by chemical route

Single-phase perovskite structure Pb_1−xBa_xTiO₃ thin films (x=0.30, 0.50 and 0.70) were deposited on Pt/Ti/SiO₂/Si substrates by the spin-coating technique. The dielectric study reveals that the thin films undergo a diffuse type ferroelectric phase transition, which shows a broad peak. An increase of the diffusivity degree with the increasing Barium contents was observed, and it was associated to a grain decrease in the studied composition range. The temperature dependence of the phonon frequencies was used to characterize the phase transition temperatures. Raman modes persist above tetragonal to cubic phase transition temperature, although all optical modes should be Raman inactive. The origin of these modes was interpreted in terms of breakdown of the local cubic symmetry by chemical disorder. The absence of a well-defined transition temperature and the presence of broad bands in some interval temperature above FE-PE phase transition temperature suggested a diffuse type phase transition. This result corroborates the dielectric constant versus temperature data, which showed a broad ferroelectric phase transition in these thin films. The leakage current density of the PBT thin films was studied at different temperatures and the data follow the Schottky emission model. Through this analysis the Schottky barrier height values 0.75, 0.53 and 0.34 eV were obtained to the PBT70, PBT50 and PBT30 thin films, respectively.     

Nanocrystalline formation and optical properties of germanium thin films prepared by physical vapor deposition

Amorphous and nanocrystalline germanium thin films were prepared on glass substrates by physical vapor deposition (PVD). The influence of thermal annealing on the characteristics of the Ge thin films has been investigated. X-ray diffraction (XRD) and SEM show amorphous structure of films deposited at room temperature. After thermal annealing, the crystallinity was improved when the annealing temperature increases. The Ge thin films annealed at different temperatures in air were nanocrystalline, having the face-centered cubic structure with preferred orientation along the 〈1 1 1〉 direction. The nanostructural parameters have been evaluated by using a single-order Voigt profile analysis. Moreover, the analysis of the optical transmission and reflection behavior was carried out. The values of direct and indirect band gap energies for amorphous and nanocrystalline phases are 0.86±0.02, 0.65±0.02 and 0.79±0.02, 0.61±0.02 eV, respectively. In addition, the complex optical functions for the wavelength range 600-2200 nm are reported. The refractive index of the nanocrystalline phase drops from 4.80±0.03 to 2.04±0.02, and amorphous phase changes from 5.18±0.03 to 2.42±0.02 for the whole wavelength range. The dielectric functions ε₁ and ε₂ of the deposited films were recorded as a function of wavelength within the range from 600 to 2200 nm.     

Optical properties and adhesion of air oxidized vacuum evaporated bismuth thin films

Highly adhesive bismuth oxide thin films on glass have been prepared by air oxidation of vacuum evaporated bismuth thin films at various temperatures. The transmittance, optical band gap, refractive index and adhesion show temperature and oxidation time effects. The films show a direct band gap between 2 and 2.5 eV. The refractive indices are in the range 1.854-1.991. The transmittances of the bismuth oxide films are quite high in a large wavelength range. These bismuth oxide films can have potential use in optical waveguides.     

Deposition and characterization of transparent and conductive sprayed ZnO:B thin films

Highly transparent and conductive Boron doped zinc oxide (ZnO:B) thin films were deposited using chemical spray pyrolysis (CSP) technique on glass substrate. The effect of variation of boron doping concentration in reducing solution on film properties was investigated. Low angle X-ray analysis showed that the films were polycrystalline fitting well with a hexagonal wurtzite structure and have preferred orientation in [002] direction. The films with resistivity 2.54×10⁻³ Ω-cm and optical transmittance >90% were obtained at optimized boron doping concentration. The optical band gap of ZnO:B films was found ∼3.27 eV from the optical transmittance spectra for the as-deposited films. Due to their excellent optical and electrical properties, ZnO:B films are promising contender for their potential use as transparent window layer and electrodes in solar cells.     

Property enhancement of transparent conducting zinc oxide thin films—Effect of simultaneous (Sn+F) doping

Undoped and simultaneously (Sn+F) doped ZnO thin films were fabricated using a simplified spray pyrolysis technique and the effects of Sn doping level on their electrical, structural, optical and surface morphological properties were studied. The XRD patterns confirmed the hexagonal wurtzite structure of ZnO. The minimum electrical resistivity of 0.45×10⁻² Ω cm was obtained for ZnO films having Sn+F doping levels of 8+20 at%. All the films exhibited average optical transmittance of 85% in the visible region, suitable for transparent electrode applications. The overall quality of the fabricated films was confirmed from photoluminescence (PL) studies. The PL and surface morphological studies along with the elemental analysis showed the increase of Sn diffusion into the ZnO lattice which was consistent with the concentration of Sn in the starting solution. The results of the analysis of physical properties of simultaneously doped ZnO films proved that these films might be considered as promising candidates for solar cells and other opto-electronic applications.     

Investigation of optical properties of annealed aluminum phthalocyanine derivatives thin films

Semiconducting molecular materials based on aluminum phthalocyanine chloride (AlPcCl) and bidentate amines have been successfully used to prepare thin films by using a thermal evaporation technique. The morphology of the deposited films was studied by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Studies of the optical properties were carried out on films deposited onto quartz and (1 0 0) monocrystalline silicon wafers and films annealed after deposition. The absorption spectra recorded in the UV–vis region for the as-deposited and annealed samples showed two absorption bands, namely the Q- and B-bands. In addition, an energy doublet in the absorption spectra of the monoclinic form at 1.81 and 1.99 eV was observed. A band-model theory was employed in order to determine the optical parameters. The fundamental energy gap (direct transitions) was determined to be within the 2.47–2.59 and 2.24–2.44 eV ranges, respectively, for the as-deposited and annealed thin films.     

Derivation of the optical constants of spin coated CeO2-TiO2-ZrO2 thin films prepared by sol-gel route

Ternary thin films of cerium titanium zirconium mixed oxide were prepared by the sol-gel process and deposited by a spin coating technique at different spin speeds (1000-4000 rpm). Ceric ammonium nitrate, Ce(NO₃)₆(NH₄)₂, titanium butoxide, Ti[O(CH₂)₃CH₃]₄, and zirconium propoxide, Zr(OCH₂CH₂CH₃)₄, were used as starting materials. Differential calorimetric analysis (DSC) and thermogravimetric analysis (TGA) were carried out on the CeO₂-TiO₂-ZrO₂ gel to study the decomposition and phase transition of the gel. For molecular, structural, elemental, and morphological characterization of the films, Fourier Transform Infrared (FTIR) spectral analysis, X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS), cross-sectional scanning electron microscopy (SEM), and atomic force microscopy (AFM) were carried out. All the ternary oxide thin films were amorphous. The optical constants (refractive index, extinction coefficient, band gap) and thickness of the films were determined in the 350-1000 nm wavelength range by using an nkd spectrophotometer. The refractive index, extinction coefficient, and thickness of the films were changed by varying the spin speed. The oscillator and dispersion energies were obtained using the Wemple-DiDomenico dispersion relationship. The optical band gap is independent of the spin speed and has a value of about E_g≈2.82±0.04 eV for indirect transition.     

Characterization of poly (3-methyl thiophene) thin films prepared by modified chemical bath deposition

Poly (3-methyl thiophene) thin films were prepared by chemical bath deposition technique on glass substrate; the prepared thin films were characterized for structural, morphological and optical properties. The variation in the oxidant concentration has an influence on the properties of the P3MeT thin films. The increase in the oxidant concentration leads to increase in the thickness of the film. The binding energy increases due to increase in oxidation concentration. The P3MeT thin films show smooth surface morphology with increase in oxidant concentration whereas the contact angle of the thin film decreases with increase in oxidant concentration. The optical absorbance of these thin films was found to increase with decrease in the optical band gap due to increase in oxidant concentration.     

Evolution of structural and optical properties of rutile TiO2 thin films synthesized at room temperature by chemical bath deposition method

Nanocrystalline thin films of TiO₂ were prepared on glass substrates from an aqueous solution of TiCl₃ and NH₄OH at room temperature using the simple and cost-effective chemical bath deposition (CBD) method. The influence of deposition time on structural, morphological and optical properties was systematically investigated. TiO₂ transition from a mixed anatase–rutile phase to a pure rutile phase was revealed by low-angle XRD and Raman spectroscopy. Rutile phase formation was confirmed by FTIR spectroscopy. Scanning electron micrographs revealed that the multigrain structure of as-deposited TiO₂ thin films was completely converted into semi-spherical nanoparticles. Optical studies showed that rutile thin films had a high absorption coefficient and a direct bandgap. The optical bandgap decreased slightly (3.29–3.07 eV) with increasing deposition time. The ease of deposition of rutile thin films at low temperature is useful for the fabrication of extremely thin absorber (ETA) solar cells, dye-sensitized solar cells, and gas sensors.     

Improvement of electrical properties of Sr-modified (Pb,Ca)TiO3 thin films grown by soft chemistry route

Strontium and calcium-modified lead titanate (Pb_0.70Ca_0.15Sr_0.15)TiO₃ soft chemistry-derived thin films were prepared on platinum-coated silicon substrate by spin-coating method. Investigations were made on the structure, surface morphology and electrical properties of the film. The results by XRD and FE-SEM showed that the film exhibits a pure tetragonal perovskite phase and an average grain size of about 50-60 nm, respectively. Electrical measurements of a metal-ferroelectric-metal type capacitor exhibited a stable and switchable electrical polarization in the film. The structure of the Au/PCST/Pt capacitor showed well-saturated hysteresis loops at an applied voltage of 300 kV/cm with remanent polarization and coercive field values of 22 μC/cm² and 100 kV/cm, respectively. At 100 kHz, the dielectric constant and the dielectric loss of the (Pb_0.70Ca_0.15Sr_0.15)TiO₃ thin film with thickness 240 nm were 528 and 0.05, respectively.     

Changes in the optical properties of as-deposited plasma polymerized 2,6-diethylaniline thin films by iodine doping

In this study, plasma polymerized 2, 6-diethylaniline (PPDEA) thin films of different thicknesses were synthesized using a glow discharge plasma polymerization method. Scanning electron microscopy showed that the surface morphology of an as-deposited PPDEA thin film was comparatively smooth after iodine doping. The iodine-doped PPDEA was found to be thermally stable up to ca about 560 K, which was slightly lower than that observed for as-deposited PPDEA. Ultraviolet-visible spectroscopic analyses demonstrated that iodine doping resulted in a significant decrease in the optical energy gap. As the doping period increased, the direct optical transition energy gap was reduced from 3.56 to 2.79 eV and the indirect optical transition energy gap was decreased from 2.23 to 1.97 eV. Thus it is observed that, the optical parameters of as-deposited PPDEA thin films with different thicknesses can be modified with different iodine doping periods.     

Influence of deposition parameters on the structural and optical properties of CdS thin films obtained by micro-controlled SILAR deposition

Polycrystalline CdS films were obtained by a micro-controlled SILAR deposition technique, using aqueous solutions of cadmium acetate and thiourea as precursors. The structural and optical properties of the films were found to be influenced by various deposition parameters such as number of immersion cycles, concentration of the precursors and temperature of the solutions. Contrary to the observations made by some researchers, we found that the thickness of the films increased continuously with number of immersion cycles and also with concentration of the precursor solutions. We also found that the films covered the substrates uniformly, without any voids, unlike the films obtained by others. Effect of deposition parameters on thickness, substrate coverage, grain size, chemical composition, optical band gap and other properties of the films is discussed in detail.