Low-temperature thermoelectric properties of Bi85Sb15−xNbx alloys prepared by high-press sintering

The nanocrystalline materials with the general formula Bi₈₅Sb_15−xNb_x (x=0, 0.5, 1, 2, 3) were prepared by mechanical alloying and subsequent high-pressure sintering. Their transport properties involving electrical conductivity, Seebeck coefficient and thermal conductivity have been investigated in the temperature range of 80-300 K. The absolute value of Seebeck coefficient of Bi₈₅Sb₁₃Nb₂ reaches a maximum of 161 μV/K at 105 K, which is 69% larger than that of Bi₈₅Sb₁₅ at the same temperature. The power factor and figure-of-merit are 4.45×10⁻³ WK⁻²m⁻¹ at 220 K and 1.79×10⁻³ K⁻¹ at 196 K, respectively. These results suggest that thermoelectric properties of Bi₈₅Sb₁₅ based material can be improved by Nb doping.     

Thermoelectric performance of ternary Bi-Sb-Ag alloys prepared by mechanical alloying and subsequent pressureless sintering

The alloys with the general formula of Bi₈₅Sb_15−xAg_x (x=0, 1, 3, 5, 7) were prepared by mechanical alloying and subsequent pressureless sintering (Bi₈₅Sb₁₅ alloy was used for comparison). Their transport properties involving electrical conductivity, Seebeck coefficient, and thermal conductivity had been investigated in the temperature range of 80-300 K. The maximum absolute value of Seebeck coefficient (120 μV/K) was found at 160 K in the alloy Bi₈₅Sb_15−xAg_x (x=3). The figure-of-merit of alloy Bi₈₅Sb_15−xAg_x (x=1) reached a maximum value of 2.16×10⁻³ K⁻¹ at 219 K, which is as large again as that of the reference sample Bi₈₅Sb₁₅.     

Thermoelectric properties of Bi0.9Sb0.1 prepared by high pressure

The Bi_0.9Sb_0.1 powders were prepared by mechanical alloying and then pressed under 6 GPa at different pressing temperatures. X-ray diffraction spectra showed that the single phase was formed. The nanostructure of grain was observed by bright-field imaging. Electrical conductivity, Seebeck coefficient, and thermal conductivity had been investigated in the temperature range of 80-300 K. The absolute Seebeck coefficient value of 120.3 μV/K was measured at 130 K. The figure-of-merit reached a maximum value of 0.90×10⁻³ K⁻¹ at 140 K.     

Thermoelectric properties of Bi-Sb semiconducting alloys prepared by quenching and annealing

Bi_100−xSb_x (x=8-17) alloys were prepared by direct melting of constituent elements, which was followed by quenching and annealing. The synthesis of high-homogeneity alloys was confirmed by X-ray diffraction, differential thermal analyses and electron microprobe analysis. The semiconducting and thermoelectric properties of the samples were investigated by measuring Hall coefficient, electrical resistivity and Seebeck coefficient in the temperature range from 20 to 300 K for both the as-quenched and annealing samples. The properties change gradually with the Sb concentration x, which is attributed to the variation of the energy gap. The Hall mobility was enhanced by annealing, which leads to a small electrical resistivity and a large Seebeck coefficient. Consequently, large values of about 8.5 mW/mK² for the power factor were obtained in the annealed alloys of x=8,12, and 14.     

Power factor enhancement in Pr-substituted alloys prepared by high-pressure sintering

Bi₈₅Sb_15−xPr_x (x=0,1,2,3) alloys with partial substitution of Pr for Sb were synthesized by mechanical alloying followed by high-pressure sintering. The crystal structure was characterized by X-ray diffraction. The electrical conductivity and Seebeck coefficient were measured in the temperature range of 80–300 K. The results show that the electrical conductivity and Seebeck coefficient of Pr-substituted samples are both larger than those of the reference sample, Bi₈₅Sb₁₅, in the whole measurement temperature range. The power factor of Bi₈₅Sb₁₃Pr₂ reaches a maximum value of 3.83×10⁻³ W K⁻² m⁻¹ at 235 K, which is about four times larger than that of the reference sample, Bi₈₅Sb₁₅, at the same temperature.     

Thermoelectric properties of Ge-doped Bi85Sb15 alloys at low temperatures

Bulk polycrystalline Bi₈₅Sb_15−xGe_x (x=0, 0.5, 1, 1.5, 2) composites were prepared by mechanical alloying followed by pressureless sintering. The thermoelectric properties were studied in the temperature range of 77–300 K. The results indicate that increasing the Ge concentration causes the Seebeck coefficient to change sign from negative to positive. Moreover, it is found that the maximum value of the Seebeck coefficient can be precisely controlled with the Ge concentration. The maximum dimensionless figure of merit reaches 0.07 at 140 K. These results suggest that the preparation of p-type Bi–Sb alloys is possible by using the Ge-doping approach.     

Transport coefficients and defect structure of Sb2−xAgxTe3 single crystals

Incorporation of Ag in the crystal lattice of Sb₂Te₃ creates structural defects that have a strong influence on the transport properties. Single crystals of Sb_2−xAg_xTe₃ (x=0.0; 0.014; 0.018 and 0.022) were characterized by measurements of the temperature dependence of the electrical resistivity, Hall coefficient, Seebeck coefficient and thermal conductivity in the temperature range of 5-300 K. With an increasing content of Ag the electrical resistance, the Hall coefficient and the Seebeck coefficient all decrease. This implies that the incorporation of Ag atoms in the Sb₂Te₃ crystal structure results in an increasing concentration of holes. However, the doping efficiency of Ag appears to be only about 50% of the expected value. We explain this discrepancy by a model based on the interaction of Ag impurity with the native defects in the Sb_2−xAg_xTe₃ crystal lattice. Defects have a particularly strong influence on the thermal conductivity. We analyze the temperature dependence of the lattice thermal conductivity in the context of the Debye model. Of the various phonon scattering contributions, the dominant influence of Ag incorporation in the crystal lattice of Sb₂Te₃ is revealed to be point-defect scattering where both the mass defect and elastic strain play a pivotal role.     

Temperature dependence of thermoelectric properties of Ni-doped CoSb3

Temperature dependences of the Hall coefficient, Hall mobility and thermoelectric properties of Ni-doped CoSb₃ have been characterized over the temperature range from 20 to 773 K. Ni-doped CoSb₃ is an n-type semiconductor and the conduction type changes from n-type to p-type at around 450 K. The temperature for the transition from n-type to p-type increased with increasing Ni content x. The Seebeck coefficient reaches a maximum value near the transition temperature. The electrical resistivity indicates that Co_1−xNi_xSb₃ is a typical semiconductor when x≤0.03 and a degenerate semiconductor when x>0.03. Thermal conductivity analyses show that the lattice component is predominant at lower temperatures and carrier and bipolar components become large at temperatures higher than the transition temperature. The thermoelectric figure of merit reaches a maximum value close to the transition temperature and the largest value, 4.67×10⁻⁴ K⁻¹ at 600 K, was obtained for x=0.05.     

Annealing effects on the structural and electrical transport properties of n-type Bi2Te2.7Se0.3 thin films deposited by flash evaporation

N-type Bi₂Te_2.7Se_0.3 thermoelectric thin films with thickness 800 nm have been deposited on glass substrates by flash evaporation method at 473 K. Annealing effects on the thermoelectric properties of Bi₂Te_2.7Se_0.3 thin films were examined in the temperature range 373-573 K. The structures, morphology and chemical composition of the thin films were characterized by X-ray diffraction, field emission scanning electron microscope and energy dispersive X-ray spectroscopy, respectively. Thermoelectric properties of the thin films have been evaluated by measurements of the electrical resistivity and Seebeck coefficient at 300 K. The Hall coefficients were measured at room temperature by the Van der Pauw method. The carrier concentration and mobility were calculated from the Hall coefficient. The films thickness of the annealed samples was measured by ellipsometer. When annealed at 473 K, the electrical resistivity and Seebeck coefficient are 2.7 mΩ cm and −180 μV/K, respectively. The maximum of thermoelectric power factor is enhanced to 12 μW/cm K².     

Annealing temperature influence on electrical properties of ion beam sputtered Bi2Te3 thin films

Ion beam sputtering process was used to deposit n-type fine-grained Bi₂Te₃ thin films on BK7 glass substrates at room temperature. In order to enhance the thermoelectric properties, thin films are annealed at the temperatures ranging from 100 to 400 °C. X-ray diffraction (XRD) shows that the films have preferred orientations in the c-axis direction. It is confirmed that grain growth and crystallization along the c-axis are enhanced as the annealing temperature increased. However, broad impurity peaks related to some oxygen traces increase when the annealing temperature reached 400 °C. Thermoelectric properties of Bi₂Te₃ thin films were investigated at room temperature. The Bi₂Te₃ thin films, including as-deposited, exhibit the Seebeck coefficients of −90 to −168 μV K⁻¹ and the electrical conductivities of 3.92×10²-7.20×10² S cm⁻¹ after annealing. The Bi₂Te₃ film with a maximum power factor of 1.10×10⁻³ Wm⁻¹ K⁻² is achieved when annealed at 300 °C. As a result, both structural and transport properties have been found to be strongly affected by annealing treatment. It was considered that the annealing conditions reduce the number of potential scattering sites at grain boundaries and defects, thus improving the thermoelectric properties.     

Effect of varying mixture ratio of raw material powders on the thermoelectric properties of AlMgB14-based materials prepared by spark plasma sintering

Thermoelectric properties of AlMgB₁₄-based materials prepared by spark plasma sintering were investigated. Al, Mg, and B powders were used as raw material powders. The raw powders were mixed using a V-shaped mixer, and then the mixture was sintered at 1673 K or 1773 K. The mixture ratio of raw powders was varied around stoichiometric ratio of AlMgB₁₄. X-ray diffraction patterns of samples showed that all samples consist of AlMgB₁₄ and MgAl₂O₄. The Seebeck coefficient of the samples exhibited significant change depending on the varying mixture ratio and sintering temperature. One sample exhibited a large negative value for the Seebeck coefficient (approximately −500 μV/K) in the temperature range from 573 K to 1073 K, while others showed positive value (250–450 μV/K). Thus n-type AlMgB₁₄-based material has been realized by varying raw material ratio and sintering temperature.     

Third-order nonlinear optical properties of Bi2S3 and Sb2S3 nanorods studied by the Z-scan technique

Bismuth sulfide (Bi₂S₃) and antimony sulfide (Sb₂S₃) nanorods were synthesized by hydrothermal method. The products were characterized by UV-vis spectrophotometer, X-ray powder diffraction (XRD) and transmission electron microscope (TEM). Bi₂S₃ and Sb₂S₃ nanorods were measured by Z-scan technique to investigate the third-order nonlinear optical (NLO) properties. The result of NLO measurements shows that the Bi₂S₃ and Sb₂S₃ nanorods have the behaviors of the third-order NLO properties of both NLO absorption and NLO refraction with self-focusing effects. The third-order NLO coefficient χ⁽³⁾ of the Bi₂S₃ and Sb₂S₃ nanorods are 6.25×10⁻¹¹ esu and 4.55×10⁻¹¹ esu, respectively. The Sb₂S₃ and Bi₂S₃ nanorods with large third-order NLO coefficient are promising materials for applications in optical devices.     

Study of the microstructure influence on the transport properties of Bi86.5Sb13.5 polycrystalline alloy

This study is focused on the investigation of the transport properties of Bi_86.5Sb_13.5 polycrystalline alloys. Bulk materials were prepared by cold pressing ultrafine powders of alloy and by annealing the resulting pellets. Special care was taken to avoid contamination of the powders. Starting with powders of average grain size of 0.06 μm bulk semi-conducting sample with mean grain size respectively of 0.1, 0.8, 2.5 and 200 μm were obtained. The influence of the grain size on both electrical resistivity, thermal conductivity, thermoelectric power, thermoelectric figure of merit is presented within the range 80-330 K. The thermoelectric properties are discussed and compared with those of single crystals presented in previous studies.     

Influence of negative pressure on thermoelectric properties of Sb2Te3

We investigated the influence of negative pressure on the electrical conductivity, the Seebeck coefficient, and the power factor of Sb₂Te₃. We performed first-principles calculations with the linearized-augmented plane-wave method considering negative hydrostatic pressure in the range from zero to −2 GPa and doping for electrons and holes up to 10²⁰ cm⁻³. Our results predict a significant increase of the Seebeck coefficient and the power factor under negative pressure for certain doping concentrations.     

Optical and thermoelectric characterizations of electroplated n-Bi2(Te0.9Se0.1)3

Bismuth selenotelluride (Bi₂(Te_0.9Se_0.1)₃) films were electrodeposited at constant current density from acidic aqueous solutions with Arabic gum in order to produce thin films for miniaturized thermoelectric devices. X-ray fluorescence spectroscopy determined film compositions. X-ray diffraction pattern shows that the films as deposited are polycrystalline, isostructural to Bi₂Te₃ and covered by crystallites. Mueller-matrix analysis reveals that the electroplated layers are optically like an isotropic medium. Their pseudo-dielectric functions were determined using mid-infrared spectroscopic ellipsometry. Tauc-Lorentz combined with Drude dispersion relations were successfully used. The energy band gap E_g was found to be about 0.15 eV. Moreover, the fundamental absorption edge was described by an indirect optical band-to-band transition. From Seebeck coefficient measurement, films exhibit n-type charge carrier and the value of thermoelectric power is about −40 μV/K.     

Anomalous increase of the thermopower and thermoelectric figure of merit in Ga-doped <Emphasis Type="Italic">p</Emphasis>-(Bi<Subscript>0.5</Subscript>Sb<Subscript>0.5</Subscript>)<Subscript>2</Subscript>Te<Subscript>3</Subscript> single crystals

The effect of Ga doping on the temperature dependences (5 K ≤ T ≤ 300 K) of the Seebeck coefficient α, electrical conductivity σ, thermal conductivity coefficient κ, and thermoelectric figure of merit Z of p-(Bi_0.5Sb_0.5)₂Te₃ single crystals has been investigated. It has been shown that, upon Ga doping, the hole concentration decreases, the Seebeck coefficient increases, the electrical conductivity decreases, and the thermoelectric figure of merit increases. The observed variations in the Seebeck coefficient cannot be completely explained by the decrease in the hole concentration and indicate a noticeable variation in the density of states due to the Ga doping.     

Effect of composition and thermal annealing on the absorption and electrical conduction of Se85−xTe15Sbx glasses

The optical absorption of the as-prepared and thermally annealed Se_85−xTe₁₅Sb_x (0≤x≤9) thin films was measured. The mechanism of the optical absorption follows the rule of non-direct transition. The optical energy gap (E₀) decreased from 1.12 to 0.84 eV with increasing Sb content of the as-prepared films from 0 to 9 at.%. The as-prepared Se₇₆Te₁₅Sb₉ films showed an increase in (E₀) with increasing the temperature of annealing in the range above T_g (363 K). The electrical conductivity of the as-prepared and annealed films was found to be of Arrhenius type with temperature in the range 300-360 K. The activation energy for conduction was found to decrease with increasing both the Sb content and temperature of annealing. The results were discussed on the basis of the lone-pair electron effect and of amorphous crystalline transformation.     

Seebeck and magnetoresistive effects of Ga-doped ZnO thin films prepared by RF magnetron sputtering

In this paper, Ga-doped ZnO (GZO) films were deposited on glass substrates at different substrate temperatures by RF magnetron sputtering. The effect of substrate temperature on the structural, surface morphological properties, Seebeck and magnetoresistive effects of GZO films was investigated. It is found that the GZO films are polycrystalline and preferentially in the [0 0 2] orientation, and the film deposited at 300 °C has an optimal crystal quality. Seebeck and magnetoresistive effects are apparently observed in GZO films. The thermoelectromotive forces are negative. Decreasing substrate temperature and annealing in N₂ flow can decrease carrier concentration. The absolute value of the Seebeck coefficient increases with decreasing carrier concentration. The maximal absolute value of Seebeck coefficient is 101.54 μV/K for the annealed samples deposited at the substrate temperature of 200 °C. The transverse magnetoresistance of GZO films is related to both the magnetic field intensity and the Hall mobility. The magnetoresistance increases almost linearly with magnetic field intensity, and the films deposited at higher substrate temperature have a stronger magnetoresistance under the same magnetic field, due to the larger Hall mobility.     

Hall mobility of amorphous Ge2Sb2Te5

The electrical conductivity, Seebeck coefficient, and Hall coefficient of three-micron-thick films of amorphous Ge₂Sb₂Te₅ have been measured as functions of temperature from room temperature down to as low as 200 K. The electrical conductivity manifests an Arrhenius behavior. The Seebeck coefficient is p-type with behavior indicative of multi-band transport. The Hall mobility is n-type and low (near 0.07 cm²/V s at room temperature).     

Structure and low-temperature properties of Ba8Ni6Ge40

Structural, magnetic, heat capacity, electrical and thermal transport properties are reported on polycrystalline Ba₈Ni₆Ge₄₀. Ba₈Ni₆Ge₄₀ crystallizes in a cubic type I clathrate structure with unit cell a=10.5179 (4) Å. It is diamagnetic with susceptibility χ_dia=−1.71×10^-6 emu/g Oe. An Einstein temperature 75 K and a Debye temperature 307 K are estimated from heat capacity data. It exhibits n-type conducting behavior below 300 K. It shows high Seebeck coefficients (−111×10^-6 V/K), low thermal conductivity (2.25 W/K m), and low electrical resistivity (8.8 mΩ cm) at 300 K.