Determination of selenium in water by electrothermal atomic absorption spectrometry

Summary The electrothermal atomization of selenium has been investigated for the accurate determination of selenium in water samples. Hydrogen seriously affects the atomization temperature of selenium in a molybdenum micro-tube atomizer. The atomization of selenium also suffers from serious interferences caused by salts and other elements. The extraction of selenium diethyldithiocarbamate complex serves to eliminate the interferences from the matrix. The addition of copper allows the suppression of interferences from elements extracted with selenium. The method permits the determination of selenium(IV) and selenium(VI) separately.This research was in part funded by the Ministry of Education, Science and Culture, Japan, under Grant-in-Aid for Scientific Research, for which we express our appreciation.     

Determination of vanadium in urine by electrothermal atomic absorption spectrometry

After wet ashing of the urine sample with nitric acid, vanadium is chelated with cupferron, extracted into 4-methylpentan-2-one and determined by atomic absorption spectrometry with a pyrolytically-coated graphite furnace atomizer. The sensitivity allows the precise determination of 1–500 μg V l^-1 in urine. The coefficient of variation for triplicate urine measurements is <8% for 10 μg V l^-1.     

Determination of aluminium in silicon by electrothermal atomic absorption spectrometry

The sample is decomposed with hydrofluoric and nitric acids and the diluted solution is injected into the graphite furnace. For a 100-mg sample, the detection limit (3 σ) is 1.2 μg AI g^-1. The coefficient of variation is 3–13% for 9–7000 μg Al g^-1 in silicon.     

Use of cetyltrimethylammonium bromide as surfactant for the determination of copper and chromium in gasoline emulsions by electrothermal atomic absorption spectrometry

In this work, the use of cetyltrimethylammonium bromide as surfactant for the preparation of oil-in-water emulsions for the determination of Cu and Cr in gasoline by electrothermal atomic absorption spectrometry (ET AAS) was evaluated. The surfactant amount was tested in the range of 25 to 300 mg, added to 2 ml of gasoline, and completed to 10 mL with 0.1% (v/v) nitric acid solution. 150 mg of surfactant was found optimum, and a sonication time of 10 min sufficient to form an oil-in-water emulsion that was stable for several hours. The ET AAS temperature program was established based on pyrolysis and atomization curves. The pyrolysis temperatures were set at 700 and 1300 °C for Cu and Cr, respectively and the selected atomization temperatures were 2400 and 2500 °C. The time and temperature of the drying stage and the atomization time were experimentally tested to provide optimum conditions. The limits of detection were found to be 5 μg L^− 1 and 1.5 μg L^− 1 for Cu and Cr, respectively in the original gasoline samples. The relative standard deviation (RSD) ranged from 4 to 9% in oil-in-water emulsions spiked with 5 μg L^− 1 and 15 μg L^− 1 of each metal, respectively. Recoveries varied from 90 to 98%. The accuracy of the proposed method was tested by an alternate procedure using complete evaporation of the gasoline sample. The method was adequate for the determination of Cu and Cr in gasoline samples collected from different gas stations in Salvador, BA, Brazil.     

Determination of gallium in biological materials by electrothermal atomic absorption spectrometry

In this determination of gallium, the condition of the graphite tubes influences the peak height. Common acids and salts seriously affect the results, but in the presence of EDTA, interferences of nitric and hydrochloric acids are suppressed completely, and interferences of phosphoric acid and some salts are suppressed partly. To compensate for the effects, a standard addition procedure is proposed, and is applied to healthy and tumor.bearing mice. A linear calibration is obtained for 0.12–12 ng Ga in 50-μl aliquots. The method is applied to tissues and body fluids with good recovery and precision.     

Determination of arsenic in biological fluids by electrothermal atomic absorption spectrometry

A procedure for the determination of the total content of arsenic in urine, serum and blood by electrothermal atomic absorption spectrometry (ETAAS) is described. Zeeman correction is used to compensate the high background signals. The samples are diluted (1 + 1 for urine and 1 + 3 for both serum and blood samples) in a medium containing 0.1% w/v Triton X-100 before being introduced directly into the furnace. A solution containing 15% w/v hydrogen peroxide, 0.65% w/v nitric acid and 0.5% w/v nickel is also introduced into the atomizer by means of a separate injection. Calibration is carried out against aqueous standards for blood and serum samples and using the standard additions method for urine samples. The detection limit is 20 pg (2 ng ml-1). The reliability of the procedure is checked by analyzing three certified reference materials and by recovery studies.     

Determination of thallium in natural waters by electrothermal atomic absorption spectrometry

Thallium is determined in natural waters by electrothermal atomic absorption Spectrometry after preconcentration. Thallium is oxidized and retained as the tetrachlorothallate (III) ion on an anion exchange column, followed by elution with ammonium sulfite solution. A concentration factor of 400 is achieved. The detection limit of the method is 3.3 ng/1.     

Determination of lithium in human serum by electrothermal atomic absorption spectrometry

An efficient method was developed for the determination of nanogram levels of lithium in biological samples. Serum samples from human subjects from southeastern Spain, treated or not treated with lithium carbonate, were analyzed by electrothermal atomic absorption spectrometry. The samples were previously treated with a matrix modifier consisting of 0.1% Triton X-100 and injected through a graphite tube with L'vov platform. The Li concentrations measured by the procedure described for the 3 certified reference samples used were not significantly different (p > 0.05) than certified levels. Sample recoveries and variability during several days, with coefficients of variation from 4.00 to 14.8%, demonstrated the reliability and accuracy of this technique. Mean Li concentration determined in the serum of individuals with psychiatric disorders treated with Li (n = 117, 5.077 +/- 1.795 microg Li/mL) was significantly higher (p < 0.001) than that in individuals not treated with Li (n = 24, 1.902 +/- 2.054 ng Li/mL).     

Determination of chromium in gallium arsenide by electrothermal atomic absorption spectrometry

The sample is decomposed with 50% (v/v) aqua regia and the diluted solution is injected into the graphite furnace. The temperature program developed minimizes non-specific background signals, so that correction is not required. For a 100-mg sample, the 3σ detection limit is 70 ng Cr g^?1. The relative standard deviation of the overall procedure is 5–7%.     

Determination of copper in milk powder by electrothermal atomic absorption and atomic emission spectrometry

Summary Electrothermal atomic absorption spectrometry (ETA-AAS) and atomic emission spectrometry (ETA-AES) have been applied to the determination of copper in powdered milk. A homogeneous dispersion procedure for the preparation of the milk powder is described which was found to be simple, rapid and less susceptible to contamination than dry ashing or wet digestion methods. Both ETA-AAS and ETA-AES techniques were found to provide satisfactory results using conventional tube wall atomisation only when the method of standard additions was employed. The application of graphite probe atomisation in ETA-AES and ETA-AAS allowed the development of direct methods for the determination of copper in milk powder using aqueous standard calibration curves. The accuracy of the probe ETA-AAS method was confirmed using new reference materials prepared by the EEC Community Bureau of Reference. Acceptable agreement was obtained for the other procedures using a commercial milk powder sample with a copper content of 6.0g g^–1.     

Determination of manganese in serum and urine by electrothermal atomic absorption spectrometry

Manganese is determined in serum and urine by graphite-furnace atomic absorption spectrometry after dilution (1 + 1) with distilled water. Simple aqueous standards are used for calibration. Background absorption from the matrix is decreased by attention to the heating programme, sample dilution and gas flow-rate during atomisation. Remaining background absorption is removed by a deuterium-arc background correction system. To obtain accurate results, great care is needed in collecting samples to avoid contamination. Blood is collected through a plastic cannula, because stainless steel needles introduce considerable contamination. The mean normal concentration of manganese in serum was found to be 0.58 μg l^?1 (it- = 9) which is in agreement with other literature values. For urine, the mean normal concentration found was 0.7 μg l^?1 (it- = 16). Patients on total parenteral nutrition with manganese supplements show elevated serum and urine manganese concentrations.     

Determination of micromolar concentrations of iodide by electrothermal atomic absorption spectrometry

When a solution (at pH 3.4–4.8) containing iodide and mercury(II) nitrate in a graphite tube is heated by increasing the temperature at a uniform rate, two mercury absorption peaks appear because the decomposition temperature of mercury(II) iodide is higher than that of mercury(II) nitrate. Measurement of the second peak allows 1 × 10^-6–5 × 10^-5 M iodide to be determined with good reproducibility. Equimolar concentrations of cyanide, sulfide and thiosulfate interfered, but these anions could be destroyed with hydrogen peroxide. Interfering cations were removed by extraction of 8-quinolinol complexes.     

Determination of traces of molybdenum in foods by electrothermal atomic absorption spectrometry

Low levels of molybdenum in different food samples were determined by atomic absorption spectrometry with electrothermal atomization after destruction of organic matter using four different methods, involving dry ashing at 600°C, wet digestion with heating with nitric/sulphuric and nitric/sulphuric/perchloric acid mixtures or direct extraction with dilute hydrochloric acid. In all cases the working conditions, reproducibility, precision and accuracy were investigated. The dry ashing method was generally the optimum destruction method.     

Determination of Mo and Bi in steels by electrothermal atomic absorption spectrometry after complexation and sorption on activated carbon

A simple method for the preconcentration of Mo and Bi in steels is proposed. The analytes are complexed with the ammonium salt of dithiophosphoric acid O,O-diethyl ester and sorbed onto activated carbon. After desorption into a small volume of nitric acid at low pH, Mo and Bi are determined by electrothermal atomic absorption spectrometry. Iron(III) is reduced to Fe(II), which is not complexed and not significantly retained on the carbon. Enrichment factor of 23 and 26 were obtained for Mo and Bi, respectively. The method was applied to the analysis of four certified reference steels, after acid dissolution in a microwave system and good agreement was obtained with the certified or recommended values.     

Determination of lead in biological materials by constant-temperature electrothermal atomic absorption spectrometry

A comparison is made between a platform-equipped Perkin-Elmer HGA-500 and a recently designed two-step constant-temperature graphite furnace with respect to susceptibility to interference effects as well as attainable detection limits. It is shown that larger quantities of biological samples can be used with the constant-temperature furnace without suppressing the analyte signal, resulting in lower detection limits. Materials studied include NBS Olyster Tissue and Bovine Liver, and human lung tissue and human blood.     

Determination of lead in blood by tungsten coil electrothermal atomic absorption spectrometry

A method for the determination of lead in blood using a tungsten coil atomizer is described. A 100 μl volume of the whole blood sample is transferred to a sampler cup containing 100 μl of water plus 300 μl of 0.25% v/v Triton X-100. After lysis of blood cells, 500 μl of 10% w/v trichloroacetic acid is added for protein precipitation and 10 μl of the supernatant solution is automatically delivered into the tungsten coil. The furnace heating program is implemented in 41 s. It is shown by the paired t-test that there is no significant difference at the 5% probability level between results obtained by the proposed method and by using a transversely heated graphite atomizer with a longitudinal Zeeman background correction. Accuracy is also assessed by employing reference materials. The proposed tungsten coil procedure presents a characteristic mass of 15 pg Pb and a detection limit of 1.9 μg Pb dl⁻¹.     

Determination of copper in sulfide minerals by Zeeman electrothermal atomic absorption spectrometry

A method for the determination of copper in some sulfide minerals (lorandite, realgar, orpiment, marcasite, stibnite, galenite and sphalerite) by Zeeman electrothermal atomic absorption spectrometry is presented. After the dissolution of samples, copper was extracted with sodium diethyldithiocarbamate into different organic solvents (carbon tetrachloride, chloroform and methylisobutyl ketone) at pH 11.0–12.0. The procedure was verified by standard addition. The standard deviation (SD) for 0.5 ng Cu is 0.01 ng, the relative standard deviation ranges from 3.5 to 5.5% and the detection limit of the method, calculated as 3 SD of the blank, was found to be 0.05 μg · g^–1.